SYSTEMPORT has its RXCHK parser block that attempts to validate the
packet structures, unfortunately setting the L2 header check bit will
cause Bridge PDUs (BPDUs) to be incorrectly rejected because they look
like LLC/SNAP packets with a non-IPv4 or non-IPv6 Ethernet Type.

Fixes: 4e8aedfe78c7 ("net: systemport: Turn on offloads by default")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN filtering can be built into the kernel, and also dynamically turned
on/off through the bridge master device. Allow re-configuring the switch
appropriately to account for that by deciding whether VLAN table
(v_table) misses should lead to a drop or forward.

Fixes: a2482d2c ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We were not consistent in how the default VID of a given port was
defined, b53_br_leave() would make sure the VLAN ID would be either 0/1
depending on the switch generation, but b53_configure_vlan(), which is
the default configuration would unconditionally set it to 1. The correct
value is 1 for 5325/5365 series and 0 otherwise. To avoid repeating that
mistake ever again, introduce a helper function: b53_default_pvid() to
factor that out.

Fixes: 967dd82f ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzkaller again found a path to a kernel crash through bad gso input.
By building an excessively large packet to cause an skb field to wrap.

If VIRTIO_NET_HDR_F_NEEDS_CSUM was set this would have been dropped in
skb_partial_csum_set.

GSO packets that do not set checksum offload are suspicious and rare.
Most callers of virtio_net_hdr_to_skb already pass them to
skb_probe_transport_header.

Move that test forward, change it to detect parse failure and drop
packets on failure as those cleary are not one of the legitimate
VIRTIO_NET_HDR_GSO types.

Fixes: bfd5f4a3 ("packet: Add GSO/csum offload support.")
Fixes: f43798c2 ("tun: Allow GSO using virtio_net_hdr")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The features attribute is of type u64 and stored in the native endianes on
the system. The for_each_set_bit() macro takes a pointer to a 32 bit array
and goes over the bits in this area. On little Endian systems this also
works with an u64 as the most significant bit is on the highest address,
but on big endian the words are swapped. When we expect bit 15 here we get
bit 47 (15 + 32).

This patch converts it more or less to its own for_each_set_bit()
implementation which works on 64 bit integers directly. This is then
completely in host endianness and should work like expected.

Fixes: fd867d51 ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some PHY drivers like the generic one do not provide a read_status
callback on their own but rely on genphy_read_status being called
directly.

With the current code, this results in a NULL function pointer call.
Call genphy_read_status instead when there is no specific callback.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit c706863b ("net: ip6_gre: always reports o_key to
userspace"), ip6gre and ip6gretap tunnels started reporting TUNNEL_KEY
output flag even if it is not configured.
ip6gre_fill_info checks erspan_ver value to add TUNNEL_KEY for
erspan tunnels, however in commit 84581bda ("erspan: set
erspan_ver to 1 by default when adding an erspan dev")
erspan_ver is initialized to 1 even for ip6gre or ip6gretap
Fix the issue moving erspan_ver initialization in a dedicated routine

Fixes: c706863b ("net: ip6_gre: always reports o_key to userspace")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2019-02-15' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just a few fixes this time:
 * mesh rhashtable fixes from Herbert
 * a small error path fix when starting AP interfaces
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull block fixes from Jens Axboe:

 - Ensure we insert into the hctx dispatch list, if a request is marked
   as DONTPREP (Jianchao)

 - NVMe pull request, single missing unlock on error fix (Keith)

 - MD pull request, single fix for a potentially data corrupting issue
   (Nate)

 - Floppy check_events regression fix (Yufen)

* tag 'for-linus-20190215' of git://git.kernel.dk/linux-block:
  md/raid1: don't clear bitmap bits on interrupted recovery.
  floppy: check_events callback should not return a negative number
  nvme-pci: add missing unlock for reset error
  blk-mq: insert rq with DONTPREP to hctx dispatch list when requeue

Merge tag 'for-5.0/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - Fix bug in DM crypt's sizing of its block integrity tag space,
   resulting in less memory use when DM crypt layers on DM integrity.

 - Fix a long-standing DM thinp crash consistency bug that was due to
   improper handling of FUA. This issue is specific to writes that fill
   an entire thinp block which needs to be allocated.

* tag 'for-5.0/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm thin: fix bug where bio that overwrites thin block ignores FUA
  dm crypt: don't overallocate the integrity tag space

Pull MMC fixes from Ulf Hansson:
 "A couple of MMC fixes intended for v5.0-rc7.

  MMC core:
   - Fix deadlock bug for block I/O requests

  MMC host:
   - sunxi: Disable broken HS-DDR mode for H5 by default
   - sunxi: Avoid unsupported speed modes declared via DT
   - meson-gx: Restore interrupt name"

* tag 'mmc-v5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: meson-gx: fix interrupt name
  mmc: block: handle complete_work on separate workqueue
  mmc: sunxi: Filter out unsupported modes declared in the device tree
  mmc: sunxi: Disable HS-DDR mode for H5 eMMC controller by default

Pull drm fixes from Dave Airlie:
 "Usual pull request, little larger than I'd like but nothing too
  strange in it. Willy found an bug in the lease ioctl calculations, but
  it's a drm master only ioctl which makes it harder to mess with.

 i915:
   - combo phy programming fix
   - opregion version check fix for VBT RVDA lookup
   - gem mmap ioctl race fix
   - fbdev hpd during suspend fix
   - array size bounds check fix in pmu

  amdgpu:
   - Vega20 psp fix
   - Add vrr range to debugfs for freesync debugging

  sched:
   - Scheduler race fix

  vkms:
   - license header fixups

  imx:
   - Fix CSI register offsets for i.MX51 and i.MX53.
   - Fix delayed page flip completion events on i.MX6QP due to
     unexpected behaviour of the PRE when issuing NOP buffer updates to
     the same buffer address.
   - Stop throwing errors for plane updates on disabled CRTCs when a
     userspace process is killed while a plane update is pending.
   - Add missing of_node_put cleanup in imx_ldb_bind"

* tag 'drm-fixes-2019-02-15-1' of git://anongit.freedesktop.org/drm/drm:
  drm: Use array_size() when creating lease
  drm/amdgpu/psp11: TA firmware is optional (v3)
  drm/i915/opregion: rvda is relative from opregion base in opregion 2.1+
  drm/i915/opregion: fix version check
  drm/i915: Prevent a race during I915_GEM_MMAP ioctl with WC set
  drm/i915: Block fbdev HPD processing during suspend
  drm/i915/pmu: Fix enable count array size and bounds checking
  drm/i915/cnl: Fix CNL macros for Voltage Swing programming
  drm/i915/icl: combo port vswing programming changes per BSPEC
  drm/vkms: Fix license inconsistent
  drm/amd/display: Expose connector VRR range via debugfs
  drm/sched: Always trace the dependencies we wait on, to fix a race.
  gpu: ipu-v3: pre: don't trigger update if buffer address doesn't change
  gpu: ipu-v3: Fix CSI offsets for imx53
  drm/imx: imx-ldb: add missing of_node_puts
  gpu: ipu-v3: Fix i.MX51 CSI control registers offset
  drm/imx: ignore plane updates on disabled crtcs

Pull crypto fix from Herbert Xu:
 "This fixes a crash on resume in the ccree driver"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: ccree - fix resume race condition on init

Pull networking fixes from David Miller:

 1) Fix MAC address setting in mac80211 pmsr code, from Johannes Berg.

 2) Probe SFP modules after being attached, from Russell King.

 3) Byte ordering bug in SMC rx_curs_confirmed code, from Ursula Braun.

 4) Revert some r8169 changes that are causing regressions, from Heiner
    Kallweit.

 5) Fix spurious connection timeouts in netfilter nat code, from Florian
    Westphal.

 6) SKB leak in tipc, from Hoang Le.

 7) Short packet checkum issue in mlx4, similar to a previous mlx5
    change, from Saeed Mahameed. The issue is that whilst padding bytes
    are usually zero, it is not guarateed and the hardware doesn't take
    the padding bytes into consideration when generating the checksum.

 8) Fix various races in cls_tcindex, from Cong Wang.

 9) Need to set stream ext to NULL before freeing in SCTP code, from Xin
    Long.

10) Fix locking in phy_is_started, from Heiner Kallweit.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
  net: ethernet: freescale: set FEC ethtool regs version
  net: hns: Fix object reference leaks in hns_dsaf_roce_reset()
  mm: page_alloc: fix ref bias in page_frag_alloc() for 1-byte allocs
  net: phy: fix potential race in the phylib state machine
  net: phy: don't use locking in phy_is_started
  selftests: fix timestamping Makefile
  net: dsa: bcm_sf2: potential array overflow in bcm_sf2_sw_suspend()
  net: fix possible overflow in __sk_mem_raise_allocated()
  dsa: mv88e6xxx: Ensure all pending interrupts are handled prior to exit
  net: phy: fix interrupt handling in non-started states
  sctp: set stream ext to NULL after freeing it in sctp_stream_outq_migrate
  sctp: call gso_reset_checksum when computing checksum in sctp_gso_segment
  net/mlx5e: XDP, fix redirect resources availability check
  net/mlx5: Fix a compilation warning in events.c
  net/mlx5: No command allowed when command interface is not ready
  net/mlx5e: Fix NULL pointer derefernce in set channels error flow
  netfilter: nft_compat: use-after-free when deleting targets
  team: avoid complex list operations in team_nl_cmd_options_set()
  net_sched: fix two more memory leaks in cls_tcindex
  net_sched: fix a memory leak in cls_tcindex
  ...

Pull signal fix from Eric Biederman:
 "Just a single patch that restores PTRACE_EVENT_EXIT functionality that
  was accidentally broken by last weeks fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  signal: Restore the stop PTRACE_EVENT_EXIT

The starting of AP interface can fail due to invalid
beacon interval, which does not match the minimum gcd
requirement set by the wifi driver. In such case, the
beacon interval of that interface gets updated with
that invalid beacon interval.

The next time that interface is brought up in AP mode,
an interface combination check is performed and the
beacon interval is taken from the previously set value.

In a case where an invalid beacon interval, i.e. a beacon
interval value which does not satisfy the minimum gcd criteria
set by the driver, is set, all the subsequent trials to
bring that interface in AP mode will fail, even if the
subsequent trials have a valid beacon interval.

To avoid this, in case of a failure in bringing up an
interface in AP mode due to interface combination error,
the interface beacon interval which is stored in bss
conf, needs to be restored with the last working value
of beacon interval.

Tested on ath10k using WCN3990.

Cc: stable@vger.kernel.org
Fixes: 0c317a02 ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When rhashtable insertion fails the mesh table code doesn't free
the now-orphan mesh path object.  This patch fixes that.

Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The mesh table code walks over hash tables for two purposes.  First of
all it's used as part of a netlink dump process, but it is also used
for looking up entries to delete using criteria other than the hash
key.

The second purpose is directly contrary to the design specification
of rhashtable walks.  It is only meant for use by netlink dumps.

This is because rhashtable is resizable and you cannot obtain a
stable walk over it during a resize process.

In fact mesh's use of rhashtable for dumping is bogus too.  Rather
than using rhashtable walk's iterator to keep track of the current
position, it always converts the current position to an integer
which defeats the purpose of the iterator.

Therefore this patch converts all uses of rhashtable walk into a
simple linked list.

This patch also adds a new spin lock to protect the hash table
insertion/removal as well as the walk list modifications.  In fact
the previous code was buggy as the removals can race with each
other, potentially resulting in a double-free.

Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Passing an object_count of sufficient size will make
object_count * 4 wrap around to be very small, then a later function
will happily iterate off the end of the object_ids array.  Using
array_size() will saturate at SIZE_MAX, the kmalloc() will fail and
we'll return an -ENOMEM to the norty userspace.

Fixes: 62884cd3 ("drm: Add four ioctls for managing drm mode object leases [v7]")
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Dave Airlie <airlied@redhat.com>

amdgpu:
- Vega20 psp fix
- Add vrr range to debugfs for freesync debugging

sched:
- Scheduler race fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190213202958.3336-1-alexander.deucher@amd.com

Merge tag 'drm-intel-fixes-2019-02-13' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

drm/i915 fixes for v5.0-rc7:
- combo phy programming fix
- opregion version check fix for VBT RVDA lookup
- gem mmap ioctl race fix
- fbdev hpd during suspend fix
- array size bounds check fix in pmu
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/877ee3504b.fsf@intel.com

drm-misc-fixes for v5.0:
- Fix license inconsistency in vkms.
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/812e2f53-d72a-8fba-6c8c-fde8f44cf141@linux.intel.com

When provisioning a new data block for a virtual block, either because
the block was previously unallocated or because we are breaking sharing,
if the whole block of data is being overwritten the bio that triggered
the provisioning is issued immediately, skipping copying or zeroing of
the data block.

When this bio completes the new mapping is inserted in to the pool's
metadata by process_prepared_mapping(), where the bio completion is
signaled to the upper layers.

This completion is signaled without first committing the metadata.  If
the bio in question has the REQ_FUA flag set and the system crashes
right after its completion and before the next metadata commit, then the
write is lost despite the REQ_FUA flag requiring that I/O completion for
this request must only be signaled after the data has been committed to
non-volatile storage.

Fix this by deferring the completion of overwrite bios, with the REQ_FUA
flag set, until after the metadata has been committed.

Cc: stable@vger.kernel.org
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

This reverts commit 8099b047.

It turns out that people do actually depend on the shebang string being
truncated, and on the fact that an interpreter (like perl) will often
just re-interpret it entirely to get the full argument list.
Reported-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 2a5f14f2.

This patch causes xfstests generic/311 to fail. Reverting this for
now until we have a proper fix.
Signed-off-by: Abhi Das <adas@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently the ethtool_regs version is set to 0 for FEC devices.

Use this field to store the register dump version exposed by the
kernel. The choosen version 2 corresponds to the kernel compile test:

        #if defined(CONFIG_M523x) || defined(CONFIG_M527x)
        || defined(CONFIG_M528x) || defined(CONFIG_M520x)
        || defined(CONFIG_M532x) || defined(CONFIG_ARM)
        || defined(CONFIG_ARM64) || defined(CONFIG_COMPILE_TEST)

and version 1 corresponds to the opposite. Binaries of ethtool unaware
of this version will dump the whole set as usual.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The basic idea behind ->pagecnt_bias is: If we pre-allocate the maximum
number of references that we might need to create in the fastpath later,
the bump-allocation fastpath only has to modify the non-atomic bias value
that tracks the number of extra references we hold instead of the atomic
refcount. The maximum number of allocations we can serve (under the
assumption that no allocation is made with size 0) is nc->size, so that's
the bias used.

However, even when all memory in the allocation has been given away, a
reference to the page is still held; and in the `offset < 0` slowpath, the
page may be reused if everyone else has dropped their references.
This means that the necessary number of references is actually
`nc->size+1`.

Luckily, from a quick grep, it looks like the only path that can call
page_frag_alloc(fragsz=1) is TAP with the IFF_NAPI_FRAGS flag, which
requires CAP_NET_ADMIN in the init namespace and is only intended to be
used for kernel testing and fuzzing.

To test for this issue, put a `WARN_ON(page_ref_count(page) == 0)` in the
`offset < 0` path, below the virt_to_page() call, and then repeatedly call
writev() on a TAP device with IFF_TAP|IFF_NO_PI|IFF_NAPI_FRAGS|IFF_NAPI,
with a vector consisting of 15 elements containing 1 byte each.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: fix locking issue

Russell pointed out that the locking used in phy_is_started() isn't
needed and misleading. This locking also contributes to a race fixed
with patch 2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell reported the following race in the phylib state machine
(quoting from his mail):

if (phy_polling_mode(phydev) && phy_is_started(phydev))
	phy_queue_state_machine(phydev, PHY_STATE_TIME);

state = PHY_UP
thread 0			thread 1
				phy_disconnect()
				+-phy_is_started()
phy_is_started()                |
				`-phy_stop()
				  +-phydev->state = PHY_HALTED
				  `-phy_stop_machine()
				    `-cancel_delayed_work_sync()
phy_queue_state_machine()
`-mod_delayed_work()

At this point, the phydev->state_queue() has been added back onto the
system workqueue despite phy_stop_machine() having been called and
cancel_delayed_work_sync() called on it.

Fix this by protecting the complete operation in thread 0.

Fixes: 2b3e88ea ("net: phy: improve phy state checking")
Reported-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell suggested to remove the locking from phy_is_started() because
the read is atomic anyway and actually the locking may be more
misleading.

Fixes: 2b3e88ea ("net: phy: improve phy state checking")
Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The clean target in the makefile conflicts with the generic
kselftests lib.mk, and fails to properly remove the compiled
test programs.

Remove the redundant rule, the TEST_GEN_FILES will be already
removed by the CLEAN macro in lib.mk.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The value of ->num_ports comes from bcm_sf2_sw_probe() and it is less
than or equal to DSA_MAX_PORTS.  The ds->ports[] array is used inside
the dsa_is_user_port() and dsa_is_cpu_port() functions.  The ds->ports[]
array is allocated in dsa_switch_alloc() and it has ds->num_ports
elements so this leads to a static checker warning about a potential out
of bounds read.

Fixes: 8cfa9498 ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With many active TCP sockets, fat TCP sockets could fool
__sk_mem_raise_allocated() thanks to an overflow.

They would increase their share of the memory, instead
of decreasing it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge.  When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.

I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts).  Some interrupts are
directly cleared by reading the Global 1 status register.  However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.

The code only services interrupts whose status bit is set at the time of reading its status
register.  If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.

This is not a problem with polling or level interrupts since the handler will be called
again to process the event.  However, it's a big problem when using level interrupts.

The fix presented here is to add a loop around the code servicing switch interrupts.  If
any pending interrupts remain after the current set has been handled, we loop and process
the new set.  If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.

Tested on espressobin board.

Fixes: dc30c35b ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

phylib enables interrupts before phy_start() has been called, and if
we receive an interrupt in a non-started state, the interrupt handler
returns IRQ_NONE. This causes problems with at least one Marvell chip
as reported by Andrew.
Fix this by handling interrupts the same as in phy_mac_interrupt(),
basically always running the phylib state machine. It knows when it
has to do something and when not.
This change allows to handle interrupts gracefully even if they
occur in a non-started state.

Fixes: 2b3e88ea ("net: phy: improve phy state checking")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In sctp_stream_init(), after sctp_stream_outq_migrate() freed the
surplus streams' ext, but sctp_stream_alloc_out() returns -ENOMEM,
stream->outcnt will not be set to 'outcnt'.

With the bigger value on stream->outcnt, when closing the assoc and
freeing its streams, the ext of those surplus streams will be freed
again since those stream exts were not set to NULL after freeing in
sctp_stream_outq_migrate(). Then the invalid-free issue reported by
syzbot would be triggered.

We fix it by simply setting them to NULL after freeing.

Fixes: 5bbbbe32 ("sctp: introduce stream scheduler foundations")
Reported-by: syzbot+58e480e7b28f2d890bfd@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jianlin reported a panic when running sctp gso over gre over vlan device:

  [   84.772930] RIP: 0010:do_csum+0x6d/0x170
  [   84.790605] Call Trace:
  [   84.791054]  csum_partial+0xd/0x20
  [   84.791657]  gre_gso_segment+0x2c3/0x390
  [   84.792364]  inet_gso_segment+0x161/0x3e0
  [   84.793071]  skb_mac_gso_segment+0xb8/0x120
  [   84.793846]  __skb_gso_segment+0x7e/0x180
  [   84.794581]  validate_xmit_skb+0x141/0x2e0
  [   84.795297]  __dev_queue_xmit+0x258/0x8f0
  [   84.795949]  ? eth_header+0x26/0xc0
  [   84.796581]  ip_finish_output2+0x196/0x430
  [   84.797295]  ? skb_gso_validate_network_len+0x11/0x80
  [   84.798183]  ? ip_finish_output+0x169/0x270
  [   84.798875]  ip_output+0x6c/0xe0
  [   84.799413]  ? ip_append_data.part.50+0xc0/0xc0
  [   84.800145]  iptunnel_xmit+0x144/0x1c0
  [   84.800814]  ip_tunnel_xmit+0x62d/0x930 [ip_tunnel]
  [   84.801699]  gre_tap_xmit+0xac/0xf0 [ip_gre]
  [   84.802395]  dev_hard_start_xmit+0xa5/0x210
  [   84.803086]  sch_direct_xmit+0x14f/0x340
  [   84.803733]  __dev_queue_xmit+0x799/0x8f0
  [   84.804472]  ip_finish_output2+0x2e0/0x430
  [   84.805255]  ? skb_gso_validate_network_len+0x11/0x80
  [   84.806154]  ip_output+0x6c/0xe0
  [   84.806721]  ? ip_append_data.part.50+0xc0/0xc0
  [   84.807516]  sctp_packet_transmit+0x716/0xa10 [sctp]
  [   84.808337]  sctp_outq_flush+0xd7/0x880 [sctp]

It was caused by SKB_GSO_CB(skb)->csum_start not set in sctp_gso_segment.
sctp_gso_segment() calls skb_segment() with 'feature | NETIF_F_HW_CSUM',
which causes SKB_GSO_CB(skb)->csum_start not to be set in skb_segment().

For TCP/UDP, when feature supports HW_CSUM, CHECKSUM_PARTIAL will be set
and gso_reset_checksum will be called to set SKB_GSO_CB(skb)->csum_start.

So SCTP should do the same as TCP/UDP, to call gso_reset_checksum() when
computing checksum in sctp_gso_segment.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS fixes for net

The following patchset contains Netfilter/IPVS fixes for net:

1) Missing structure initialization in ebtables causes splat with
   32-bit user level on a 64-bit kernel, from Francesco Ruggeri.

2) Missing dependency on nf_defrag in IPVS IPv6 codebase, from
   Andrea Claudi.

3) Fix possible use-after-free from release path of target extensions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2019-02-13

This series introduces some fixes to mlx5 driver.
For more information please see tag log below.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>