Increase (and rename) the login orb reply timeout value to 20s
to match that of the old firewire stack. 2s simply didn't give
many devices enough time to spin up and reply.

Fixes inability to recognize some devices.
Failure mode was "orb reply timed out"/"failed to login".
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (style, comments, changelog)

Replace an unnecessary subtraction with a bitwise AND when determining the
value of ext_tcode in fw_fill_transaction() to save a cpu cycle or two in a
somewhat critical path.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

read_rom() obtained a fresh new fw_device.generation for each read
transaction.  Hence it was able to continue reading in the middle of the
ROM even if a bus reset happened.  However the device may have modified
the ROM during the reset.  We would end up with a corrupt fetched ROM
image then.

Although all of this is quite unlikely, it is not impossible.
Therefore we now restart reading the ROM if the bus generation changed.

Note, the memory barrier in read_rom() is still necessary according to
tests by Jarod Wilson, despite of the ->generation access being moved up
in the call chain.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This is essentially what I've been beating on locally, and I've yet to hit
another config rom read failure with it.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>

fw_device.node_id and fw_device.generation are accessed without mutexes.
We have to ensure that all readers will get to see node_id updates
before generation updates.

Fixes an inability to recognize devices after "giving up on config rom",
https://bugzilla.redhat.com/show_bug.cgi?id=429950Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Reviewed by Nick Piggin <nickpiggin@yahoo.com.au>.

Verified to fix 'giving up on config rom' issues on multiple system and
drive combinations that were previously affected.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>

We have to use the fw_device.generation here, not the fw_card.generation,
because the generation must never be newer than the node ID when we emit
a transaction.  This cannot be guaranteed with fw_card.generation.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Verified in concert with subsequent memory barriers patch to fix 'giving
up on config rom' issues on multiple system and drive combinations that
were previously affected.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>

There was a small window where a login or reconnect job could use an
already updated card generation with an outdated node ID.  We have to
use the fw_device.generation here, not the fw_card.generation, because
the generation must never be newer than the node ID when we emit a
transaction.  This cannot be guaranteed with fw_card.generation.

Furthermore, the target's and initiator's node IDs can be obtained from
fw_device and fw_card.  Dereferencing their underlying topology objects
is not necessary.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Verified in concert with subsequent memory barriers patch to fix 'giving
up on config rom' issues on multiple system and drive combinations that
were previously affected.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>

Ask the target to grant 4 seconds instead of the standard and minimum of
1 second window after bus reset for reconnection.  This accelerates
reconnection if there are more than one targets on the bus:  If a login
and inquiry to one target blocks the fw-sbp2 workqueue for more than 1s
after bus reset, we now still can reconnect to the other target.

Before that, fw-sbp2's reconnect attempts would be rejected with "error
status: 0:9" (function rejected), and fw-sbp2 would finally re-login.
All those futile reconnect attemps cost extra time until the target
which needs re-login is ready for I/O again.

The reconnect timeout field in the login ORB doesn't have to be honored
by the target though.  I found that we could get up to
  - allegedly 32768s from an old OXFW911 firmware
  - 256s from LSI bridges
  - 4s from OXUF922 and OXFW912 bridges,
  - 2s from TI bridges,
  - only the standard 1s from Initio and Prolific bridges and from
    Apple OpenFirmware in target mode.

We just try to get 4 seconds which already covers the case of a few
HDDs on the same bus quite nicely.

A minor drawback occurs in the following (rare and impractical) border
case:
  - two initiators are there, initiator 1 holds an exclusive login to
    a target,
  - initiator 1 goes off the bus,
  - target refuses login attempts from initiator 2 until reconnect_hold
    seconds after bus reset.

An alternative approach to the issue at hand would be to parallelize
fw-sbp2's reconnect and login work.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Jarod Wilson <jwilson@redhat.com>

Don't attempt to send a logout ORB if the target was already unplugged
or had its link switched off.  If two targets are attached, this
enhances the chance to quickly reconnect to the remaining target when
one target is plugged out.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Jarod Wilson <jwilson@redhat.com>

Maintainers like to receive less mail, and submitters like to have to Cc
less recipients.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Previously, the fw-ohci driver used fixed-length buffers for storing
descriptors for isochronous receive DMA programs.  If an application
(such as libdc1394) generated a DMA program that was too large, fw-ohci
would reach the limit of its fixed-sized buffer and return an error to
userspace.

This patch replaces the fixed-length ring-buffer with a linked-list of
page-sized buffers.  Additional buffers can be dynamically allocated and
appended to the list when necessary.  For a particular context, buffers
are kept around after use and reused as necessary, so there is no
allocation taking place after the DMA program is generated for the first
time.

In addition, the buffers it uses are coherent for DMA so there is no
syncing required before and after writes.  This syncing wasn't properly
done in the previous version of the code.

-

This is the fourth version of my patch that replaces a fixed-length
buffer for DMA descriptors with a dynamically allocated linked-list of
buffers.

As we discovered with the last attempt, new context programs are
sometimes queued from interrupt context, making it unacceptable to call
tasklet_disable() from context_get_descriptors().

This version of the patch uses ohci->lock for all locking needs instead
of tasklet_disable/enable.  There is a new requirement that
context_get_descriptors() be called while holding ohci->lock.  It was
already held for the AT context, so adding the requirement for the iso
context did not seem particularly onerous.  In addition, this has the
side benefit of allowing iso queue to be safely called from concurrent
user-space threads, which previously was not safe.
Signed-off-by: David Moore <dcm@acm.org>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>

-

Fixes the following issues:
  - Isochronous reception stopped prematurely if an application used a
    larger buffer.  (Reproduced with coriander.)
  - Isochronous reception stopped after one or a few frames on VT630x
    in OHCI 1.0 mode.  (Fixes reception in coriander, but dvgrab still
    doesn't work with these chips.)

Patch update: struct member alignment, whitespace nits
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

The firewire-ohci driver so far lacked the ability to resume cycle
master duty after that condition happened, as added to ohci1394 in Linux
2.6.18 by commit 57fdb58f.  This ports
this patch to fw-ohci.

The "cycle too long" condition has been seen in practice
  - with IIDC cameras if a mode with packets too large for a speed is
    chosen,
  - sporadically when capturing DV on a VIA VT6306 card with ohci1394/
    ieee1394/ raw1394/ dvgrab 2.
    https://bugzilla.redhat.com/show_bug.cgi?id=415841#c7
(This does not fix Fedora bug 415841.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Fix extraction of the source node id from the packet header.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This patch corrects a number of bugs in the current OHCI 1.0
packet-per-buffer support:

1. Correctly deal with payloads that cross a page boundary.  The
previous version would not split the descriptor at such a boundary,
potentially corrupting unrelated memory.

2. Allow user-space to specify multiple packets per struct
fw_cdev_iso_packet in the same way that dual-buffer allows.  This is
signaled by header_length being a multiple of header_size.  This
multiple determines the number of packets.  The payload size allocated
per packet is determined by dividing the total payload size by the
number of packets.

3. Make sync support work properly for packet-per-buffer.

I have tested this patch with libdc1394 by forcing my OHCI 1.1
controller to use the packet-per-buffer support instead of dual-buffer.

I would greatly appreciate testing by those who have a DV devices and
other types of iso streamers to make sure I didn't cause any
regressions.

Stefan, with this patch, I'm hoping that libdc1394 will work with all
your OHCI 1.0 controllers now.

The one bit of future work that remains for packet-per-buffer support is
the automatic compaction of short payloads that I discussed with
Kristian.
Signed-off-by: David Moore <dcm@acm.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This patch fixes the problem where different OHCI 1.1 controllers behave
differently when a received iso packet straddles three or more buffers
when using the dual-buffer receive mode.  Two changes are made in order
to handle this situation:

1. The packet sync DMA descriptor is given a non-zero header length and
non-zero payload length.  This is because zero-payload descriptors are
not discussed in the OHCI 1.1 specs and their behavior is thus
undefined.  Instead we use a header size just large enough for a single
header and a payload length of 4 bytes for this first descriptor.

2. As we process received packets in the context's tasklet, read the
packet length out of the headers.  Keep track of the running total of
the packet length as "excess_bytes", so we can ignore any descriptors
where no packet starts or ends.  These descriptors may not have had
their first_res_count or second_res_count fields updated by the
controller so we cannot rely on those values.

The main drawback of this patch is that the excess_bytes value might get
"out of sync" with the packet descriptors if something strange happens
to the DMA program.  I'm not if such a thing could ever happen, but I
appreciate any suggestions in making it more robust.

Also, the packet-per-buffer support may need a similar fix to deal with
issue 1, but I haven't done any work on that yet.

Stefan, I'm hoping that with this patch, all your OHCI 1.1 controllers
will work properly with an unmodified version of libdc1394.
Signed-off-by: David Moore <dcm@acm.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

SBP2_MAX_SECTORS is nowhere used in fw-sbp2.
It merely got copied over from sbp2 where it played a role in the past.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This somewhat reduces the size of firewire-sbp2.ko.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Bug noted by Pieter Palmers:  Isochronous transmit tasklets were
scheduled on isochronous receive events, in addition to the proper
isochronous receive tasklets.

http://marc.info/?l=linux1394-devel&m=119783196222802Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This patch speeds up sbp2 a little bit --- but more importantly, it
brings the behavior of sbp2 and fw-sbp2 closer to each other.  Like
fw-sbp2, sbp2 now does not limit the size of single transfers to 255
sectors anymore, unless told so by a blacklist flag or by module load
parameters.

Only very old bridge chips have been known to need the 255 sectors
limit, and we have got one such chip in our hardwired blacklist.  There
certainly is a danger that more bridges need that limit; but I prefer to
have this issue present in both fw-sbp2 and sbp2 rather than just one of
them.

An OXUF922 with 400GB 7200RPM disk on an S400 controller is sped up by
this patch from 22.9 to 23.5 MB/s according to hdparm.  The same effect
could be achieved before by setting a higher max_sectors module
parameter.  On buses which use 1394b beta mode, sbp2 and fw-sbp2 will
now achieve virtually the same bandwidth.  Fw-sbp2 only remains faster
on 1394a buses due to fw-core's gap count optimization.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

The code has been in "#if 0 - #endif" since Linux 2.6.12.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Convert ieee1394 from nopage to fault.
Remove redundant vma range checks (correct resource range check is retained).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Replace sg->length by sg_dma_len(sg).  Rename a variable for shorter
line lengths and eliminate some superfluous local variables.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86: (890 commits)
  x86: fix nodemap_size according to nodeid bits
  x86: fix overlap between pagetable with bss section
  x86: add PCI IDs to k8topology_64.c
  x86: fix early_ioremap pagetable ops
  x86: use the same pgd_list for PAE and 64-bit
  x86: defer cr3 reload when doing pud_clear()
  x86: early boot debugging via FireWire (ohci1394_dma=early)
  x86: don't special-case pmd allocations as much
  x86: shrink some ifdefs in fault.c
  x86: ignore spurious faults
  x86: remove nx_enabled from fault.c
  x86: unify fault_32|64.c
  x86: unify fault_32|64.c with ifdefs
  x86: unify fault_32|64.c by ifdef'd function bodies
  x86: arch/x86/mm/init_32.c printk fixes
  x86: arch/x86/mm/init_32.c cleanup
  x86: arch/x86/mm/init_64.c printk fixes
  x86: unify ioremap
  x86: fixes some bugs about EFI memory map handling
  x86: use reboot_type on EFI 32
  ...

Both the old e1000 driver and the new e1000e driver can drive some
PCI-Express e1000 cards, and we should avoid ambiguity about which
driver will pick up the support for those cards when both drivers are
enabled.

This solves the problem by having the old driver support those cards if
the new driver isn't configured, but otherwise ceding support for PCI
Express versions of the e1000 chipset to the newer driver.  Thus
allowing both legacy configurations where only the old driver is active
(and handles all chips it knows about) and the new configuration with
the new driver handling the more modern PCIE variants.
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We want IPV6HEADER matching for the non-advanced default netfilter
configuration, since it's part of the standard netfilter setup of at
least some distributions (eg Fedora).

Otherwise NETFILTER_ADVANCED loses much of its point, since even
non-advanced users would have to enable all the advanced options just to
get a working IPv6 netfilter setup.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memnode.map is s16 array because of nodeid is 16 bit now.

so need to increase the nodemap_size according to that bits.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

one early crash on one 8 node 256g machine:

Command line: console=uart8250,io,0x3f8,115200n8 initrd=kernel.org/mydisk11_x86_64.gz rw root=/dev/ram0 debug initcall_debug apic=debug acpi.debug_level=0x0000000f pci=routeirq ip=dhcp load_ramdisk=1 ramdisk_size=131072 BOOT_IMAGE=kernel.org/bzImage_2.6.25_k8.1
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009bc00 (usable)
 BIOS-e820: 000000000009bc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000dffe0000 (usable)
 BIOS-e820: 00000000dffe0000 - 00000000dffee000 (ACPI data)
 BIOS-e820: 00000000dffee000 - 00000000dffff050 (ACPI NVS)
 BIOS-e820: 00000000dffff050 - 00000000e0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 0000004020000000 (usable)
Early serial console at I/O port 0x3f8 (options '115200n8')
console [uart0] enabled
end_pfn_map = 67239936
Kernel panic - not syncing: Duplicated early reservation d40000-e42000

Pid: 0, comm: swapper Not tainted 2.6.24-smp-g5a514e21-dirty #3

Call Trace:
 [<ffffffff80221545>] lapic_get_maxlvt+0x0/0x10
 [<ffffffff80221657>] clear_local_APIC+0x5/0xcf
 [<ffffffff80221726>] disable_local_APIC+0x5/0x17
 [<ffffffff8021fe16>] smp_send_stop+0x46/0x4c
 [<ffffffff80235293>] panic+0x94/0x13e
 [<ffffffff80bc3b03>] sctp_eps_proc_init+0x12/0x34
 [<ffffffff80b9f1c5>] reserve_early+0x30/0x6c
 [<ffffffff80803925>] init_memory_mapping+0x2cd/0x2dc
 [<ffffffff80b9dc01>] setup_arch+0x21f/0x44e
 [<ffffffff80b978be>] start_kernel+0x6f/0x2c7
 [<ffffffff80b971cc>] _sinittext+0x1cc/0x1d3

it turns out there is overlap between pgtable and bss...

in System.map we have
ffffffff80d40420 b rsi_table
ffffffff80d40620 B krb5_seq_lock
ffffffff80d40628 b i.20437
ffffffff80d40630 b xprt_rdma_inline_write_padding
ffffffff80d40638 b sunrpc_table_header
ffffffff80d40640 b zero
ffffffff80d40644 b min_memreg
ffffffff80d40648 b rpcrdma_tk_lock_g
ffffffff80d40650 B sctp_assocs_id_lock
ffffffff80d40658 B proc_net_sctp
ffffffff80d40660 B sctp_assocs_id
ffffffff80d40680 B sysctl_sctp_mem
ffffffff80d40690 B sysctl_sctp_rmem
ffffffff80d406a0 B sysctl_sctp_wmem
ffffffff80d406b0 b sctp_ctl_socket
ffffffff80d406b8 b sctp_pf_inet6_specific
ffffffff80d406c0 b sctp_pf_inet_specific
ffffffff80d406c8 b sctp_af_v4_specific
ffffffff80d406d0 b sctp_af_v6_specific
ffffffff80d406d8 b sctp_rand.33270
ffffffff80d406dc b sctp_memory_pressure
ffffffff80d406e0 b sctp_sockets_allocated
ffffffff80d406e4 b sctp_memory_allocated
ffffffff80d406e8 b sctp_sysctl_header
ffffffff80d406f0 b zero
ffffffff80d406f4 A __bss_stop
ffffffff80d406f4 A _end

need to round up table_start to PAGE_SIZE.

also make the panic more informative.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

This just adds the PCI IDs of AMD's family 10h and 11h CPU's northbridges to
k8topology discovery.
Signed-off-by: Joachim Deguara <joachim.deguara@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Put appropriate pagetable update hooks in so that paravirt knows
what's going on in there.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Use a standard list threaded through page->lru for maintaining the pgd
list on PAE.  This is the same as 64-bit, and seems saner than using a
non-standard list via page->index.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

PAE mode requires that we reload cr3 in order to guarantee that
changes to the pgd will be noticed by the processor.  This means that
in principle pud_clear needs to reload cr3 every time.  However,
because reloading cr3 implies a tlb flush, we want to avoid it where
possible.

pud_clear() is only used in a couple of places:
 - in free_pmd_range(), when pulling down a range of process address space, and
 - huge_pmd_unshare()

In both cases, the calling code will do a a tlb flush anyway, so
there's no need to do it within pud_clear().

In free_pmd_range(), the pud_clear is immediately followed by
pmd_free_tlb(); we can hook that to make the mmu_gather do an
unconditional full flush to make sure cr3 gets reloaded.

In huge_pmd_unshare, it is followed by flush_tlb_range, which always
results in a full cr3-reload tlb flush.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: William Irwin <wli@holomorphy.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

This patch adds a new configuration option, which adds support for a new
early_param which gets checked in arch/x86/kernel/setup_{32,64}.c:setup_arch()
to decide wether OHCI-1394 FireWire controllers should be initialized and
enabled for physical DMA access to allow remote debugging of early problems
like issues ACPI or other subsystems which are executed very early.

If the config option is not enabled, no code is changed, and if the boot
paramenter is not given, no new code is executed, and independent of that,
all new code is freed after boot, so the config option can be even enabled
in standard, non-debug kernels.

With specialized tools, it is then possible to get debugging information
from machines which have no serial ports (notebooks) such as the printk
buffer contents, or any data which can be referenced from global pointers,
if it is stored below the 4GB limit and even memory dumps of of the physical
RAM region below the 4GB limit can be taken without any cooperation from the
CPU of the host, so the machine can be crashed early, it does not matter.

In the extreme, even kernel debuggers can be accessed in this way. I wrote
a small kgdb module and an accompanying gdb stub for FireWire which allows
to gdb to talk to kgdb using remote remory reads and writes over FireWire.

An version of the gdb stub fore FireWire is able to read all global data
from a system which is running a a normal kernel without any kernel debugger,
without any interruption or support of the system's CPU. That way, e.g. the
task struct and so on can be read and even manipulated when the physical DMA
access is granted.

A HOWTO is included in this patch, in Documentation/debugging-via-ohci1394.txt
and I've put a copy online at
ftp://ftp.suse.de/private/bk/firewire/docs/debugging-via-ohci1394.txt

It also has links to all the tools which are available to make use of it
another copy of it is online at:
ftp://ftp.suse.de/private/bk/firewire/kernel/ohci1394_dma_early-v2.diffSigned-Off-By: Bernhard Kaindl <bk@suse.de>
Tested-By: Thomas Renninger <trenn@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

In x86 PAE mode, stop treating pmds as a special case.  Previously
they were always allocated and freed with the pgd.  The modifies the
code to be the same as 64-bit mode, where they are allocated on
demand.

This is a step on the way to unifying 32/64-bit pagetable allocation
as much as possible.

There is a complicating wart, however.  When you install a new
reference to a pmd in the pgd, the processor isn't guaranteed to see
it unless you reload cr3.  Since reloading cr3 also has the
side-effect of flushing the tlb, this is an expense that we want to
avoid whereever possible.

This patch simply avoids reloading cr3 unless the update is to the
current pagetable.  Later patches will optimise this further.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: William Irwin <wli@holomorphy.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

The change from current to tsk in do_page_fault is safe as
this is set at the very beginning of the function.

Removes a likely() annotation from the 64-bit version, this
could have instead been added to 32-bit.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

When changing a kernel page from RO->RW, it's OK to leave stale TLB
entries around, since doing a global flush is expensive and they pose
no security problem.  They can, however, generate a spurious fault,
which we should catch and simply return from (which will have the
side-effect of reloading the TLB to the current PTE).

This can occur when running under Xen, because it frequently changes
kernel pages from RW->RO->RW to implement Xen's pagetable semantics.
It could also occur when using CONFIG_DEBUG_PAGEALLOC, since it avoids
doing a global TLB flush after changing page permissions.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

On !PAE 32-bit, _PAGE_NX will be 0, making is_prefetch always
return early.  The test is sufficient on PAE as __supported_pte_mask
is updated in the same places as nx_enabled in init_32.c which also
takes disable_nx into account.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Unify includes in moved fault.c.

Modify Makefiles to pick up unified file.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>