Manish Chopra says:

====================
qed*: ethtool rx flow classification enhancements.

This series re-structures the driver's ethtool rx flow
classification flow, following that it adds other flow
profiles and rx flow classification enhancements
via "ethtool -N/-U"

Please consider applying this to "net-next"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With this patch, User can configure for the supported
flows to be dropped. Added a stat "gft_filter_drop"
as well to be populated in ethtool for the dropped flows.

For example -

ethtool -N p5p1 flow-type udp4 dst-port 8000 action -1
ethtool -N p5p1 flow-type tcp4 scr-ip 192.168.8.1 action -1
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the supported classification modes [4 tuples based,
udp port based, src-ip based], flows can be classified
to the VFs as well. With this patch, flows can be re-directed
to the requested VF provided in "action" field of command.

Please note that driver doesn't really care about the queue bits
in "action" field for the VFs. Since queue will be still chosen
by FW using RSS hash. [I.e., the classification would be done
according to vport-only]

For examples -

ethtool -N p5p1 flow-type udp4 dst-port 8000 action 0x100000000
ethtool -N p5p1 flow-type tcp4 src-ip 192.16.6.10 action 0x200000000
ethtool -U p5p1 flow-type tcp4 src-ip 192.168.40.100 dst-ip \
	192.168.40.200 src-port 6660 dst-port 5550 \
	action 0x100000000
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, driver supports flow classification to PF
receive queues based on TCP/UDP 4 tuples [src_ip, dst_ip,
src_port, dst_port] only.

This patch enables to configure different flow profiles
[For example - only UDP dest port or src_ip based] on the
adapter so that classification can be done according to
just those fields as well. Although, at a time just one
type of flow configuration is supported due to limited
number of flow profiles available on the device.

For example -

ethtool -N enp7s0f0 flow-type udp4 dst-port 45762 action 2
ethtool -N enp7s0f0 flow-type tcp4 src-ip 192.16.4.10 action 1
ethtool -N enp7s0f0 flow-type udp6 dst-port 45762 action 3
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Validate and prevent some of the configurations for
unsupported [by firmware] inputs [for example - mac ext,
vlans, masks/prefix, tos/tclass] via ethtool -N/-U.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch simplifies the ethtool rx flow configuration
[via ethtool -U/-N] flow code base by dividing it logically
into various APIs based on given protocols. It also separates
various validations and calculations done along the flow
in their own APIs.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have a confusion of two different abstractions in the Common
Code:  Physical Link (Port) and Logical Network Interface (Virtual
Interface), and we haven't been properly managing the state of the
intersection of those two abstractions.
On the one hand we have the Physical state of the Link -- up or down --
and on the other we have the logical state of the VI, enabled or not.
{ethN} refers to both the Physical and Logical State. In this case,
ifconfig only affects/interrogates the Logical State of a VI,
and ethtool only deals with the Physical State. And these are different.

So, just because we disable the VI, we don't really want to change the
Physical Link Up/Down state.  Thus, the previous hack to set
"lc->link_ok = 0" when we disable a VI is completely incorrect.

Where we get into trouble is where the Physical Link State and the
Logical VI State cross swords.  And that happens in
t4_handle_get_port_info() where we need to manage/safe the Physical
Link State, but we also need to know when the Logical VI State has
changed and pass that back up to the OS-dependent Driver routine
t4_os_link_changed() which is concerned about the Logical Interface.

So we enable a VI and that causes Firmware to send us a new Port
Information message, but if none of the Physical Link State
particulars have changed, we don't call t4_os_link_changed().

This fix uses the existing OS Contract APIs for the Common Code to
inform the OS-dependent portion of the Host Driver when the "Link" (really
Logical Network Interface) is "up" or "down". A new API
t4_enable_pi_params() is added which calls t4_enable_vi_params() and,
if that is successful, then calls back to the OS Contract API
t4_os_link_changed() notifying the OS-dependent layer of the
potential Link State change.

Original Work by : Casey Leedom <leedom@chelsio.com>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

clean up init_one and use chip_ver consistently throughout
init_one() for chip version.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

newer SFPs like SFP28 and QSFP28 Transceiver Modules present
several new possibilities which we haven't faced before. Fix the
assumptions in the code reflecting the more limited capabilities
of previous Transceiver Module systems

Original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This comment is outdated as fec_ptp_ioctl has been replaced by fec_ptp_set/fec_ptp_get
since commit 1d5244d0 ("fec: Implement the SIOCGHWTSTAMP ioctl")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

efx_enqueue_skb() can push new buffers for the xmit_more functionality.
We must stops the TX queue before this or else the TX queue does not get
restarted and we get a netdev watchdog.

In the error handling we may now need to unwind more than 1 packet, and
we may need to push the new buffers onto the partner queue.

v2: In the error leg also push this queue if xmit_more is set

Fixes: e9117e50 ("sfc: Firmware-Assisted TSO version 2")
Reported-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for a new port flag - BR_ISOLATED. If it is set
then isolated ports cannot communicate between each other, but they can
still communicate with non-isolated ports. The same can be achieved via
ACLs but they can't scale with large number of ports and also the
complexity of the rules grows. This feature can be used to achieve
isolated vlan functionality (similar to pvlan) as well, though currently
it will be port-wide (for all vlans on the port). The new test in
should_deliver uses data that is already cache hot and the new boolean
is used to avoid an additional source port test in should_deliver.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: offload LAG for tc flower egress

This series from John adds bond offload to the nfp driver.  Patch 5
exposes the hash type for NETDEV_LAG_TX_TYPE_HASH to make sure nfp
hashing matches that of the software LAG.  This may be unnecessarily
conservative, let's see what LAG maintainers think :)

John says:

This patchset sets up the infrastructure and offloads output actions for
when a TC flower rule attempts to egress a packet to a LAG port.

Firstly it adds some of the infrastructure required to the flower app and
to the nfp core. This includes the ability to change the MAC address of a
repr, a function for combining lookup and write to a FW symbol, and the
addition of private data to a repr on a per app basis.

Patch 6 continues by implementing notifiers that track Linux bonds and
communicates to the FW those which enslave reprs, along with the current
state of reprs within the bond.

Patch 7 ensures bonds are synchronised with FW by receiving and acting
upon cmsgs sent to the kernel. These may request that a bond message is
retransmitted when FW can process it, or may request a full sync of the
bonds defined in the kernel.

Patch 8 offloads a flower action when that action requires egressing to a
pre-defined Linux bond.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If the egress device of an offloaded rule is a LAG port, then encode the
output port to the NFP with a LAG identifier and the offloaded group ID.

A prelag action is also offloaded which must be the first action of the
series (although may appear after other pre-actions - e.g. tunnels). This
causes the FW to check that it has the necessary information to output to
the requested LAG port. If it does not, the packet is sent to the kernel
before any other actions are applied to it.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds the control message handler to synchronize offloaded group config
with that of the kernel. Such messages are sent from fw to driver and
feature the following 3 flags:

- Data: an attached cmsg could not be processed - store for retransmission
- Xon: FW can accept new messages - retransmit any stored cmsgs
- Sync: full sync requested so retransmit all kernel LAG group info
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Monitor LAG events via the NETDEV_CHANGEUPPER/NETDEV_CHANGELOWERSTATE
notifiers to maintain a list of offloadable groups. Sync these groups with
HW via a delayed workqueue to prevent excessive re-configuration. When the
workqueue is triggered it may generate multiple control messages for
different groups. These messages are linked via a batch ID and flags to
indicate a new batch and the end of a batch.

Update private data in each repr to track their LAG lower state flags. The
state of a repr is used to determine the active netdevs that can be
offloaded. For example, in active-backup mode, we only offload the netdev
currently active.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

LAG upper event notifiers contain the tx type used by the LAG device.
Extend this to also include the hash policy used for tx types that
utilize hashing.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a bitmap to each flower repr to track its state if it is enslaved by a
bond. This LAG state may be different to the port state - for example, the
port may be up but LAG state may be down due to the selection in an
active/backup bond.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check if the fw contains the _abi_flower_balance_sync_enable symbol. If it
does then write a 1 to this indicating that the driver is willing to
receive NIC to kernel LAG related control messages.

If the write is successful, update the list of extra features supported by
the fw and add a stub to accept LAG cmsgs.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add an rtsym API function that combines the lookup of a symbol and the
writing of a value to it. Values can be written as unsigned 32 or 64 bits.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding a netdev to a bond requires that its mac address can be modified.
The default eth_mac_addr is sufficient to satisfy this requirement.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the guest network adapter is not configured with DeviceNaming
enabled on the host, then the query for friendly name will return
success but with a zero length name. Which then leads to a garbage value
(stack contents) for ifalias.

Fix is simple, just don't set name if  host doesn't return it.

Fixes: 0fe554a4 ("hv_netvsc: propogate Hyper-V friendly name into interface alias")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
net: Update fib_table_lookup tracepoints

Update the FIB lookup tracepoints to include ip proto and port fields
from the flow struct. In the process make the IPv4 tracepoint inline
with IPv6 which is much easier to use and follow the lookup and result.

Remove the tracepoint in fib_validate_source which does not provide
value above the fib_table_lookup which immediately follows it.

v2
- move CREATE_TRACE_POINTS for the v6 tracepoint to route.c to handle
  its need for an internal function to convert route type to error and
  handle IPv6 as a module or builtin. Reported by kbuild robot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tracepoint does not add value and the call to fib_lookup follows
it which shows the same information and the fib lookup result.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit bb0ad198 ("ipv6: fib6_rules: support for match on sport, dport
and ip proto") added support for protocol and ports to FIB rules.
Update the FIB lookup tracepoint to dump the parameters.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 4a2d73a4 ("ipv4: fib_rules: support match on sport, dport
and ip proto") added support for protocol and ports to FIB rules.
Update the FIB lookup tracepoint to dump the parameters.

In addition, make the IPv4 tracepoint similar to the IPv6 one where
the lookup parameters and result are dumped in 1 event. It is much
easier to use and understand the outcome of the lookup.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 05f0fe6b ("RCU, workqueue: Implement rcu_work") introduces
new API's for dispatching work in a RCU callback. Now we can just
switch to the new API's for tc filters. This could get rid of a lot
of code.

Cc: Tejun Heo <tj@kernel.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Petr Machata says:

====================
Mirroring tests involving VLAN

This patchset tests mirror-to-gretap with various underlay
configurations involving VLAN netdevice in particular. Some of the tests
involve bridges as well, but tests aimed specifically at testing bridges
(i.e. FDB, STP) are not part of this patchset.

In patches #1-#6, the codebase is adapted to support the new tests.

In patch #7, a test for mirroring to VLAN is introduced.

Patches #8-#10 add three tests where VLAN is part of underlay path after
gretap encapsulation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Test for "tc action mirred egress mirror" that mirrors to GRE when the
underlay route points at an 802.1d bridge and packet egresses through a
VLAN device.

Besides testing basic connectivity, this also tests that the traffic is
properly tagged.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test for "tc action mirred egress mirror" that mirrors to a gretap
netdevice whose underlay route points at a vlan device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test for "tc action mirred egress mirror" that mirrors to GRE when the
underlay route points at a vlan device on top of a bridge device with
vlan filtering (802.1q).
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test for "tc action mirred egress mirror" that mirrors to a vlan device.
- test_vlan() tests that the packets get mirrored
- test_tagged_vlan() tests that the mirrored packets have correct inner
  VLAN tag.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A mirror-to-vlan test that's coming next needs to install the trap
unconditionally. Therefore extract from slow_path_trap_{,un}install()
a more generic functions trap_install() and trap_uninstall(), and covert
the former two to conditional wrappers around these.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add full_test_span_gre_dir_vlan_ips() and full_test_span_gre_dir_vlan()
to support mirror-to-gre tests that involve VLAN.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add vlan_create() and vlan_destroy() to manage VLAN netdevices.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Having a clsact qdisc on $h3 is useful in several tests, and will be
useful in more tests to come. Move the registration from all the tests
that need it into the topology file itself.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For non-GRE mirroring tests, a functions along the lines of
do_test_span_gre_dir_ips() and test_span_gre_dir_ips() are necessary,
but such that they don't assume tunnels are involved. Extract the code
from mirror_gre_lib.sh to mirror_lib.sh and convert to just use a given
device without assuming it's named "h3-$tundev". Convert the two
above-mentioned functions to wrappers that pass along the correct device
name.

Add test_span_dir() and fail_test_span_dir() to round up the API for use
by following patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move generic parts of mirror_gre_topo_lib.sh into a new file
mirror_topo_lib.sh. Reuse the functions in GRE topo, adding the tunnel
devices as necessary.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf-next 2018-05-24

The following pull-request contains BPF updates for your *net-next* tree.

The main changes are:

1) Björn Töpel cleans up AF_XDP (removes rebind, explicit cache alignment from uapi, etc).

2) David Ahern adds mtu checks to bpf_ipv{4,6}_fib_lookup() helpers.

3) Jesper Dangaard Brouer adds bulking support to ndo_xdp_xmit.

4) Jiong Wang adds support for indirect and arithmetic shifts to NFP

5) Martin KaFai Lau cleans up BTF uapi and makes the btf_header extensible.

6) Mathieu Xhonneux adds an End.BPF action to seg6local with BPF helpers allowing
   to edit/grow/shrink a SRH and apply on a packet generic SRv6 actions.

7) Sandipan Das adds support for bpf2bpf function calls in ppc64 JIT.

8) Yonghong Song adds BPF_TASK_FD_QUERY command for introspection of tracing events.

9) other misc fixes from Gustavo A. R. Silva, Sirio Balmelli, John Fastabend, and Magnus Karlsson
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Thomas Falcon says:

====================
ibmvnic: Failover hardening

Introduce additional transport event hardening to handle
events during device reset. In the driver's current state,
if a transport event is received during device reset, it can
cause the device to become unresponsive as invalid operations
are processed as the backing device context changes. After
a transport event, the device expects a request to begin the
initialization process. If the driver is still processing
a previously queued device reset in this state, it is likely
to fail as firmware will reject any commands other than the
one to initialize the client driver's Command-Response Queue.

Instead of failing and becoming dormant, the driver will make
one more attempt to recover and continue operation. This is
achieved by setting a state flag, which if true will direct
the driver to clean up all allocated resources and perform
a hard reset in an attempt to bring the driver back to an
operational state.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>