- 03 Aug, 2015 13 commits
-
-
Daniel Borkmann authored
Since the introduction of the BPF action in d23b8ad8 ("tc: add BPF based action"), late binding was not working as expected. I.e. setting the action part for a classifier only via 'bpf index <num>', where <num> is the index of an existing action, is being rejected by the kernel due to other missing parameters. It doesn't make sense to require these parameters such as BPF opcodes etc, as they are not going to be used anyway: in this case, they're just allocated/parsed and then freed again w/o doing anything meaningful. Instead, parse and verify the remaining parameters *after* the test on tcf_hash_check(), when we really know that we're dealing with creation of a new action or replacement of an existing one and where late binding is thus irrelevant. After patch, test case is now working: FOO="1,6 0 0 4294967295," tc actions add action bpf bytecode "$FOO" tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 action bpf index 1 tc actions show action bpf action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe index 1 ref 2 bind 1 tc filter show dev foo filter protocol all pref 49152 bpf filter protocol all pref 49152 bpf handle 0x1 flowid 1:1 bytecode '1,6 0 0 4294967295' action order 1: bpf bytecode '1,6 0 0 4294967295' default-action pipe index 1 ref 2 bind 1 Late binding of a BPF action can be useful for preloading maps (e.g. before they hit traffic) in case of eBPF programs, or to share a single eBPF action with multiple classifiers. Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@plumgrid.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
At switch setup, _mv88e6xxx_stats_wait was called without holding the SMI mutex. Fix this by requesting the lock for this call. Also, return the _mv88e6xxx_stats_wait code, since it may fail. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Satish Ashok authored
Before this patch when a vid was not specified, the entry was added with vid 0 which is useless when vlan_filtering is enabled. This patch makes the entry to be added on all configured vlans when vlan filtering is enabled and respectively deleted from all, if the entry vid is 0. This is also closer to the way fdb works with regard to vid 0 and vlan filtering. Example: Setup: $ bridge vlan add vid 256 dev eth4 $ bridge vlan add vid 1024 dev eth4 $ bridge vlan add vid 64 dev eth3 $ bridge vlan add vid 128 dev eth3 $ bridge vlan port vlan ids eth3 1 PVID Egress Untagged 64 128 eth4 1 PVID Egress Untagged 256 1024 $ echo 1 > /sys/class/net/br0/bridge/vlan_filtering Before: $ bridge mdb add dev br0 port eth3 grp 239.0.0.1 $ bridge mdb dev br0 port eth3 grp 239.0.0.1 temp After: $ bridge mdb add dev br0 port eth3 grp 239.0.0.1 $ bridge mdb dev br0 port eth3 grp 239.0.0.1 temp vid 1 dev br0 port eth3 grp 239.0.0.1 temp vid 128 dev br0 port eth3 grp 239.0.0.1 temp vid 64 Signed-off-by:
Satish Ashok <sashok@cumulusnetworks.com> Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
David S. Miller authored
Toshiaki Makita says: ==================== Stacked vlan TSO for virtual devices Basically virtual devices do not need to segment double tagged packets. This patch set adds TSO feature for double tagged packets to several virtual devices, which can be realized by simply setting .ndo_features_check to passthru_features_check. ==================== Signed-off-by: -
Toshiaki Makita authored
Tap devices don't need to segment multiple tagged packets. Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by:
-
Toshiaki Makita authored
Bridge devices don't need to segment multiple tagged packets since thier ports can segment them. Signed-off-by:
-
Toshiaki Makita authored
Veth devices don't need to segment multiple tagged packets. Signed-off-by:
-
Toshiaki Makita authored
Macvlan/macvtap devices don't need to segment multiple tagged packets since the lower devices can segment them. Signed-off-by:
-
Eric Dumazet authored
Straightforward patch to add GRO processing to virtio_net. napi_complete_done() usage allows more aggressive aggregation, opted-in by setting /sys/class/net/xxx/gro_flush_timeout Tested: Setting /sys/class/net/xxx/gro_flush_timeout to 1000 nsec, Rick Jones reported following results. One VM of each on a pair of OpenStack compute nodes with E5-2650Lv3 CPUs and Intel 82599ES-based NICs. So, two "before" and two "after" VMs. The OpenStack compute nodes were running OpenStack Kilo, with VxLAN encapsulation being used through OVS so no GRO coming-up the host stack. The compute nodes themselves were running a 3.14-based kernel. Single-stream netperf, CPU utilizations and thus service demands are based on intra-guest reported CPU. Throughput Mbit/s, bigger is better Min Median Average Max 4.2.0-rc3+ 1364 1686 1678 1938 4.2.0-rc3+flush1k 1824 2269 2275 2647 Send Service Demand, smaller is better Min Median Average Max 4.2.0-rc3+ 0.236 0.558 0.524 0.802 4.2.0-rc3+flush1k 0.176 0.503 0.471 0.738 Receive Service Demand, smaller is better. Min Median Average Max 4.2.0-rc3+ 1.906 2.188 2.191 2.531 4.2.0-rc3+flush1k 0.448 0.529 0.533 0.692 Signed-off-by:Eric Dumazet <edumazet@google.com> Tested-by:
Rick Jones <rick.jones2@hp.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Jiri Pirko authored
Suggested-by:
Scott Feldman <sfeldma@gmail.com> Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Acked-by:
-
Ido Schimmel authored
rocker supports the transmission of scattered packets, so let the kernel know about it by setting the NETIF_F_SG bit in the device's features. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Daniel Borkmann authored
Add skb->hash to the __sk_buff offset map, so it can be accessed from an eBPF program. We currently already do this for classic BPF filters, but not yet on eBPF, it might be useful as a demuxer in combination with helpers like bpf_clone_redirect(), toy example: __section("cls-lb") int ingress_main(struct __sk_buff *skb) { unsigned int which = 3 + (skb->hash & 7); /* bpf_skb_store_bytes(skb, ...); */ /* bpf_l{3,4}_csum_replace(skb, ...); */ bpf_clone_redirect(skb, which, 0); return -1; } I was thinking whether to add skb_get_hash(), but then concluded the raw skb->hash seems fine in this case: we can directly access the hash w/o extra eBPF helper function call, it's filled out by many NICs on ingress, and in case the entropy level would not be sufficient, people can still implement their own specific sw fallback hash mix anyway. Signed-off-by: -
Yuval Mintz authored
Commit 05cc5a39 ("bnx2x: add vlan filtering offload") has introduced an incorrect logic for checking whether pvid should be configured for a vf, causing the hypervisor driver to send unneeded ramrods for all of the vfs each time a pvid has changed. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by:
Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by:
-
- 01 Aug, 2015 10 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller authored
Conflicts: arch/s390/net/bpf_jit_comp.c drivers/net/ethernet/ti/netcp_ethss.c net/bridge/br_multicast.c net/ipv4/ip_fragment.c All four conflicts were cases of simple overlapping changes. Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Must teardown SR-IOV before unregistering netdev in igb driver, from Alex Williamson. 2) Fix ipv6 route unreachable crash in IPVS, from Alex Gartrell. 3) Default route selection in ipv4 should take the prefix length, table ID, and TOS into account, from Julian Anastasov. 4) sch_plug must have a reset method in order to purge all buffered packets when the qdisc is reset, likewise for sch_choke, from WANG Cong. 5) Fix deadlock and races in slave_changelink/br_setport in bridging. From Nikolay Aleksandrov. 6) mlx4 bug fixes (wrong index in port even propagation to VFs, overzealous BUG_ON assertion, etc.) from Ido Shamay, Jack Morgenstein, and Or Gerlitz. 7) Turn off klog message about SCTP userspace interface compat that makes no sense at all, from Daniel Borkmann. 8) Fix unbounded restarts of inet frag eviction process, causing NMI watchdog soft lockup messages, from Florian Westphal. 9) Suspend/resume fixes for r8152 from Hayes Wang. 10) Fix busy loop when MSG_WAITALL|MSG_PEEK is used in TCP recv, from Sabrina Dubroca. 11) Fix performance regression when removing a lot of routes from the ipv4 routing tables, from Alexander Duyck. 12) Fix device leak in AF_PACKET, from Lars Westerhoff. 13) AF_PACKET also has a header length comparison bug due to signedness, from Alexander Drozdov. 14) Fix bug in EBPF tail call generation on x86, from Daniel Borkmann. 15) Memory leaks, TSO stats, watchdog timeout and other fixes to thunderx driver from Sunil Goutham and Thanneeru Srinivasulu. 16) act_bpf can leak memory when replacing programs, from Daniel Borkmann. 17) WOL packet fixes in gianfar driver, from Claudiu Manoil. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (79 commits) stmmac: fix missing MODULE_LICENSE in stmmac_platform gianfar: Enable device wakeup when appropriate gianfar: Fix suspend/resume for wol magic packet gianfar: Fix warning when CONFIG_PM off act_pedit: check binding before calling tcf_hash_release() net: sk_clone_lock() should only do get_net() if the parent is not a kernel socket net: sched: fix refcount imbalance in actions r8152: reset device when tx timeout r8152: add pre_reset and post_reset qlcnic: Fix corruption while copying act_bpf: fix memory leaks when replacing bpf programs net: thunderx: Fix for crash while BGX teardown net: thunderx: Add PCI driver shutdown routine net: thunderx: Fix crash when changing rss with mutliple traffic flows net: thunderx: Set watchdog timeout value net: thunderx: Wakeup TXQ only if CQE_TX are processed net: thunderx: Suppress alloc_pages() failure warnings net: thunderx: Fix TSO packet statistic net: thunderx: Fix memory leak when changing queue count net: thunderx: Fix RQ_DROP miscalculation ... -
David S. Miller authored
Tom Herbert says: ==================== ipv6: Turn on auto IPv6 flow labels by default BSD (MacOS) has already turned on flow labels by default and this does not seem to be causing any problems in the Internet. Let's go ahead and turn them on by default. We'll continue to monitor for any devices start choking on them. Flow labels are important since they are the desired solution for network devices to perform ECMP and RSS (RFC6437 and RFC6438). Traditionally, devices perform a 5-tuple hash on packets that includes port numbers. For the most part, these devices can only compute 5-tuple hashes for TCP and UDP. This severely limits our ability to get good network load balancing for other protocols (IPIP, GRE,ESP, etc.), and hence we are limited in using other protocols. Unfortunately, this method is accepted as the de facto standard to the extent that there are several proposals to encapsulate protocols in UDP _just_ for the purposes for getting ECMP to work. With hosts generating flow labels and devices taking them as input into ECMP (several already do), we can start to fix this fundamental problem. This patch set: - Changes IPV6_FLOWINFO sockopt to be opt-out of flow labels for connections rather than opt-in - Disable flow label state ranges sysctl by default - Enable auto flow labels sysctl by default v2: - Added functions to create an skb->hash based on flowi4 and flowi6. These are called in output path when creating a packet - Call skb_get_hash_flowi6 in ip6_make_flowlabel - Implement the auto_flowlabels sysctl as a mode for auto flowlabels. There are four modes which correspond to flow labels being enabled and whether socket option can be used to opt in or opt out of using them ==================== Signed-off-by: -
Tom Herbert authored
Initialize auto_flowlabels to one. This enables automatic flow labels, individual socket may disable them using the IPV6_AUTOFLOWLABEL socket option. Signed-off-by:
Tom Herbert <tom@herbertland.com> Signed-off-by:
-
Tom Herbert authored
Per RFC6437 stateful flow labels (e.g. labels set by flow label manager) cannot "disturb" nodes taking part in stateless flow labels. While the ranges only reduce the flow label entropy by one bit, it is conceivable that this might bias the algorithm on some routers causing a load imbalance. For best results on the Internet we really need the full 20 bits. Signed-off-by:
-
Tom Herbert authored
Change the meaning of net.ipv6.auto_flowlabels to provide a mode for automatic flow labels generation. There are four modes: 0: flow labels are disabled 1: flow labels are enabled, sockets can opt-out 2: flow labels are allowed, sockets can opt-in 3: flow labels are enabled and enforced, no opt-out for sockets np->autoflowlabel is initialized according to the sysctl value. Signed-off-by:
-
Tom Herbert authored
We can't call skb_get_hash here since the packet is not complete to do flow_dissector. Create hash based on flowi6 instead. Signed-off-by:
-
Tom Herbert authored
Add skb_get_hash_flowi6 and skb_get_hash_flowi4 which derive an sk_buff hash from flowi6 and flowi4 structures respectively. These functions can be called when creating a packet in the output path where the new sk_buff does not yet contain a fully formed packet that is parsable by flow dissector. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfsLinus Torvalds authored
Pull btrfs fixes from Chris Mason: "Filipe fixed up a hard to trigger ENOSPC regression from our merge window pull, and we have a few other smaller fixes" * 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: Btrfs: fix quick exhaustion of the system array in the superblock btrfs: its btrfs_err() instead of btrfs_error() btrfs: Avoid NULL pointer dereference of free_extent_buffer when read_tree_block() fail btrfs: Fix lockdep warning of btrfs_run_delayed_iputs()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/soundLinus Torvalds authored
Pull sound fixes from Takashi Iwai: "This became a relative big update as it includes the collected ASoC fixes. There are a few fixes in ASoC core side, mostly for DAPM and the new topology API. The rest are various ASoC driver-specific fixes, as well as the usual HD-audio and USB-audio quirks" * tag 'sound-4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (29 commits) ALSA: hda - Fix MacBook Pro 5,2 quirk ALSA: hda - Fix race between PM ops and HDA init/probe ALSA: usb-audio: add dB range mapping for some devices ALSA: hda - Apply a fixup to Dell Vostro 5480 ALSA: hda - Add pin quirk for the headset mic jack detection on Dell laptop ALSA: hda - Apply fixup for another Toshiba Satellite S50D ALSA: fireworks: add support for AudioFire2 quirk ALSA: hda - Fix the headset mic that will not work on Dell desktop machine ALSA: hda - fix cs4210_spdif_automute() ASoC: pcm1681: Fix setting de-emphasis sampling rate selection ASoC: ssm4567: Keep TDM_BCLKS in ssm4567_set_dai_fmt ASoC: sgtl5000: Fix up define for SGTL5000_SMALL_POP ASoC: dapm: Don't add prefix to widget stream name ASoC: rt5645: Check if codec is initialized in workqueue handler ASoC: Intel: Get correct usage_count value to load firmware ASoC: topology: Fix to add dapm mixer info ASoC: zx: spdif: Fix devm_ioremap_resource return value check ASoC: zx: i2s: Fix devm_ioremap_resource return value check ASoC: mediatek: Use platform_of_node for machine drivers ASoC: Free card DAPM context on snd_soc_instantiate_card() error path ...
-
- 31 Jul, 2015 17 commits
-
-
David S. Miller authored
Florian Fainelli says: ==================== net: GENET, SYSTEMPORT and DSA netconsole This patch series adds support for netconsole in the GENET, SYSTEMPORT and DSA drivers. A small refactoring to the DSA transmit path is required to avoid duplicating the dsa_netpoll_send_skb() into each and every tagging protocol supported. Testing on e.g: mv643xx_eth and/or e1000e would be much appreciated! Changes in v2: - properly disable/enable interrupts in GENET and SYSTEMPORT - pass the reallocated SKB back to dsa_slave_xmit() in case a tag protocol had to alter the original SKB ==================== Signed-off-by: -
Florian Fainelli authored
Add support for using DSA slave network devices with netconsole, which requires us to allocate and free custom netpoll instances and invoke the parent network device poll controller callback. In order for netconsole to work, we need to construct the DSA tag, but not queue the skb for transmission on the master network device xmit function. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Florian Fainelli authored
All tagging protocols do the same thing: increment device statistics, make room for the tag to be inserted, create the tag, invoke the parent network device transmit function. In order to prepare for adding netpoll support, which requires the tag creation, but not using the parent network device transmit function, do some little refactoring which eliminates duplication between the 4 tagging protocols supported. We need to return a sk_buff pointer back to the caller because the tag specific transmit function may have to reallocate the original skb (e.g: tag_trailer.c) and this is the one we should be transmitting, not the original sk_buff we were passed. Signed-off-by:
-
Florian Fainelli authored
Implement a poll controller for netconsole which invokes the RX interrupt handler to poll for incoming packets, and cleans up all TX queues by invoking the TX interrupt handler. Signed-off-by:
-
Florian Fainelli authored
Implement a poll controller for netconsole which invokes both of our interrupt handlers for the different RX/TX queues. Signed-off-by:
-
Joachim Eastwood authored
Commit 50649ab1 ("stmmac: drop driver from stmmac platform code") was a bit overzealous in removing code and dropped the MODULE_* macro's that are still needed since stmmac_platform can be a module. Fix this by putting the macro's remvoed in 50649ab1 back. This fixes the following errors when used as a module: stmmac_platform: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint stmmac_platform: Unknown symbol devm_kmalloc (err 0) stmmac_platform: Unknown symbol stmmac_suspend (err 0) stmmac_platform: Unknown symbol platform_get_irq_byname (err 0) stmmac_platform: Unknown symbol stmmac_dvr_remove (err 0) stmmac_platform: Unknown symbol platform_get_resource (err 0) stmmac_platform: Unknown symbol of_get_phy_mode (err 0) stmmac_platform: Unknown symbol of_property_read_u32_array (err 0) stmmac_platform: Unknown symbol of_alias_get_id (err 0) stmmac_platform: Unknown symbol stmmac_resume (err 0) stmmac_platform: Unknown symbol stmmac_dvr_probe (err 0) Fixes: 50649ab1 ("stmmac: drop driver from stmmac platform code") Reported-by:
Igor Gnatenko <i.gnatenko.brain@gmail.com> Signed-off-by:
Joachim Eastwood <manabian@gmail.com> Signed-off-by:
-
David S. Miller authored
Claudiu Manoil says: ==================== gianfar: wol magic packet fixes These changes were already validated as part of FSL SDK. Patch 2 fixes occasional wake-on magic packet failures during traffic, probably due to incorrect traffic stop/ device halt sequence and incorrect usage of txlock. ==================== Signed-off-by: -
Claudiu Manoil authored
The wol_en flag is 0 by default anyway, and we have the following inconsistency: a MAGIC packet wol capable eth interface is registered as a wake-up source but unable to wake-up the system as wol_en is 0 (wake-on flag set to 'd'). Calling set_wakeup_enable() at netdev open is just redundant because wol_en is 0 by default. Let only ethtool call set_wakeup_enable() for now. The bflock is obviously obsoleted, its utility has been corroded over time. The bitfield flags used today in gianfar are accessed only on the init/ config path, with no real possibility of concurrency - nothing that would justify smth. like bflock. Signed-off-by:
Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by:
-
Claudiu Manoil authored
If we disable NAPI in the first place we can mask the device's interrupts (and halt it) without fearing that imask may be concurrently accessed from interrupt context, so there's no need to do local_irq_save() around gfar_halt_nodisable(). lock_rx_qs()/unlock_tx_qs() are just obsoleted and potentially buggy routines. The txlock is currently used in the driver only to manage TX congestion, it has nothing to do with halting the device. With these changes, the TX processing is stopped before gfar_halt(). Compact gfar_halt() is used instead of gfar_halt_nodisable(), as it disables Rx/TX DMA h/w blocks and the Rx/TX h/w queues. gfar_start() re-enables all these blocks on resume. Enabling the magic-packet mode remains the same, note that the RX block is re-enabled just before entering sleep mode. Add IRQF_NO_SUSPEND flag for the error interrupt line, to signal that the interrupt line must remain active during sleep in order to wake the system by magic packet (MAG) reception interrupt. (On some systems the MAG interrupt did trigger w/o this flag as well, but on others it didn't.) Without these fixes, when suspended during fair Tx traffic the interface occasionally failed to be woken up by magic packet. Signed-off-by:
-
Claudiu Manoil authored
CC drivers/net/ethernet/freescale/gianfar.o drivers/net/ethernet/freescale/gianfar.c:568:13: warning: 'lock_tx_qs' defined but not used [-Wunused-function] static void lock_tx_qs(struct gfar_private *priv) ^ drivers/net/ethernet/freescale/gianfar.c:576:13: warning: 'unlock_tx_qs' defined but not used [-Wunused-function] static void unlock_tx_qs(struct gfar_private *priv) ^ Reported-by:Scott Wood <scottwood@freescale.com> Signed-off-by:
-
Nikolay Aleksandrov authored
tlb_dynamic_lb could be set only via sysfs, this patch allows it to be set via netlink. Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-next-for-davem-2015-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== Major changes: mwifiex: * add TX DATA Pause support * add multichannel and TDLS channel switch support ath10k: * enable VHT for IBSS * initial work to support qca99x0 and the corresponding 10.4 firmware branch ==================== Signed-off-by:
-
Daniel Pieczko authored
Signed-off-by:
Shradha Shah <sshah@solarflare.com> Signed-off-by:
-
Daniel Pieczko authored
The policy in the net driver is to attempt MCDI commands and then handle any EPERM error codes appropriately when returned by unprivileged functions. The ethtool selftest contains some tests which are useful on an unprivileged function, such as the event queue interrupt tests, but other tests cannot be performed as the function does not have the required permissions. If a test returns -EPERM, act as though the test was not run and continue. Signed-off-by:
-
Shaohui Xie authored
This patch added driver to support Aquantia PHYs AQ1202, AQ2104, AQR105, AQR405, which accessed through clause 45. Signed-off-by:
Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by:
-
Joe Perches authored
Use vsprintf extension %pI4 instead. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
hayeswang authored
The UEFI driver would enable zero length, and the Linux driver doesn't need it. Zero length let the hw complete the transfer with length 0, when there is no received packet. It would add the load of USB host controller and reduce the performance. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
