- Fixes in isr routine
   Fixed crash with INTA mode during driver unload. Pass hldev to request_irq
   instead of vdev.
   Fixed Traffic failure with GRO in INTA mode. Pass the correct napi
   context to gro functions.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Removed the code to bounds check the mss value. The hardware does bounds checking and
will not allow an oversized mss to lockup the transmit path.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Corrected Register map entry for xmac_link registers.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Fixed the crash in rmmod after vpath open failed when trying to change mtu.
We should check for card status before continuing in device close.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Fixed memory leak by freeing memory allocated for device_config.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Removed ioremap of bar1 address
  Driver needs only bar0 address for register access
- Removed references to bar1 and bar2 addresses
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case if kernel was compiled without ebtables support
there is no need to keep ebt_table pointers in netns_xt
structure.

Make it config dependent.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

No functional change -- just for easier reading.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allows a TIPC application to determine the number of messages
currently waiting in a socket's receive queue (TIPC_SOCK_RECVQ_DEPTH) or
in all TIPC socket receive queues (TIPC_NODE_RECVQ_DEPTH).
Signed-off-by: Oscar Medina <oscar.medina@motorola.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes an unused member (seq) scm_cookie; besides initialized
to 0 in the header file, it is not used.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replaced '0' by 'bar' in the probe function.

The 'bar' variable was already set to '0' and is already
used in pci_iomap(). This is cleaner and improves code
consistency.
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.

Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

almost no users in the tree; and the few that use them treat them
like NET_RX_DROP.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bit that tells us whether a statistics counter snapshot operation
has completed is located in the GLOBAL register block, not in the
GLOBAL2 register block, so fix up mv88e6xxx_stats_wait() to poll the
right register address.
Signed-off-by: Stephane Contri <Stephane.Contri@grassvalley.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet a écrit :
> Ingo Molnar a écrit :
>>> The following changes since commit 52989765:
>>>   Linus Torvalds (1):
>>>         Merge git://git.kernel.org/.../davem/net-2.6

> >>> are available in the git repository at:

>>>   master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6.git master
>> Hm, something in this lot quickly wrecked networking here - see the
>> tx timeout dump below. It starts with:
>>
>> [  351.004596] WARNING: at net/sched/sch_generic.c:246 dev_watchdog+0x10b/0x19c()
>> [  351.011815] Hardware name: System Product Name
>> [  351.016220] NETDEV WATCHDOG: eth0 (forcedeth): transmit queue 0 timed out
>>
>> Config attached. Unfortunately i've got no time to do bisection
>> today.
>
>
>
> forcedeth might have a problem, in its netif_wake_queue() logic, but
> I could not see why a recent patch could make this problem visible now.
>
> CPU0/1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
> is not a new cpu either :)
>
> forcedeth uses an internal tx_stop without appropriate barrier.
>
> Could you try following patch ?
>
> (random guess as I dont have much time right now)

We might have a race in napi_schedule(), leaving interrupts disabled forever.
I cannot test this patch, I dont have the hardware...
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>

The call resource_size(res) returns res->end - res->start + 1 and thus the
second change is semantics-preserving.  res_size is then used as the second
argument of a call to request_mem_region, and the memory allocated by this
call appears to be the same as what is released in the two calls to
release_mem_region.  So the size argument for those calls should be
resource_size(size) as well.  Alternatively, in the second call to
release_mem_region, the second argument could be res_size, as that variable
has already been initialized at the point of this call.

The problem was found using the following semantic patch:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct resource *res;
@@

- (res->end - res->start) + 1
+ resource_size(res)

@@
struct resource *res;
@@

- res->end - res->start
+ BAD(resource_size(res))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

add new id (RIOS System PC CARD3 ETHERNET).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch properly defines the maximum values for rx/tx coalescing timeouts.
Signed-off-by: Vlad Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Problem reported by Flavio Leitner <fleitner@redhat.com>:
When setting rx/tx coalescing timeout to the values less than 12 traffic was
stopped.

The FW supports coalescing in 12us granularity, and so value of less then 12
should be interpreted as disabling coalescing
Signed-off-by: Vlad Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is currently possible for an asynchronous device unregister
to cause the same tun device to be unregistered twice.  This
is because the unregister in tun_chr_close only checks whether
__tun_get(tfile) != NULL.  This however has nothing to do with
whether the device has already been unregistered.  All it tells
you is whether __tun_detach has been called.

This patch fixes this by using the most obvious thing to test
whether the device has been unregistered.

It also moves __tun_detach outside of rtnl_unlock since nothing
that it does requires that lock.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 537a1bf0 (fbdev: add mutex for
fb_mmap locking) introduces a ->mm_lock mutex for protecting smem
assignments. Unfortunately in the case of sm501fb these happen quite
early in the initialization code, well before the mutex_init() that takes
place in register_framebuffer(), leading to:

   Badness at kernel/mutex.c:207

   Pid : 1, Comm:          swapper
   CPU : 0                 Not tainted  (2.6.31-rc1-00284-g529ba0d9-dirty #2273)

   PC is at __mutex_lock_slowpath+0x72/0x1bc
   PR is at __mutex_lock_slowpath+0x66/0x1bc
   ...

matroxfb appears to have the same issue and has solved it with an early
mutex_init(), so we do the same for sm501fb.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6: (27 commits)
  parisc: use generic atomic64 on 32-bit
  parisc: superio: fix build breakage
  parisc: Fix PCI resource allocation on non-PAT SBA machines
  parisc: perf: wire up sys_perf_counter_open
  parisc: add task_pt_regs macro
  parisc: wire sys_perf_counter_open to sys_ni_syscall
  parisc: inventory.c, fix bloated stack frame
  parisc: processor.c, fix bloated stack frame
  parisc: fix compile warning in mm/init.c
  parisc: remove dead code from sys_parisc32.c
  parisc: wire up rt_tgsigqueueinfo
  parisc: ensure broadcast tlb purge runs single threaded
  parisc: fix "delay!" timer handling
  parisc: fix mismatched parenthesis in memcpy.c
  parisc: Fix gcc 4.4 warning in lba_pci.c
  parisc: add parameter to read_cr16()
  parisc: decode_exc.c should include kernel.h
  parisc: remove obsolete hw_interrupt_type
  parisc: fix irq compile bugs in arch/parisc/kernel/irq.c
  parisc: advertise PCI devs after "assign_resources"
  ...

Manually fixed up trivial conflicts in tools/perf/perf.h due to addition
of SH vs HPPA perf-counter support.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: fix pcap adc locking
  mfd: sm501, fix lock imbalance

* 'for-2.6.31' of git://linux-nfs.org/~bfields/linux:
  NFSD: Don't hold unrefcounted creds over call to nfsd_setuser()

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Fix CONFIG_FLATMEM version of pfn_valid()
  MIPS: Reorganize Cavium OCTEON PCI support.
  Update Yoichi Yuasa's e-mail address
  MIPS: Allow suspend and hibernation again on uniprocessor kernels.
  MIPS: 64-bit: Fix o32 core dump
  MIPS: BC47xx: Fix SSB irq setup
  MIPS: CMP: Update sync-r4k for current kernel
  MIPS: CMP: Move gcmp_probe to before the SMP ops
  MIPS: CMP: activate CMP support
  MIPS: CMP: Extend IPI handling to CPU number
  MIPS: CMP: Extend the GIC IPI interrupts beyond 32
  MIPS: Define __arch_swab64 for all mips r2 cpus
  MIPS: Update VR41xx GPIO driver to use gpiolib
  MIPS: Hookup new syscalls sys_rt_tgsigqueueinfo and sys_perf_counter_open.
  MIPS: Malta: Remove unnecessary function prototypes
  MIPS: MT: Remove unnecessary semicolons
  MIPS: Add support for Texas Instruments AR7 System-on-a-Chip

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  sound: do not set DEVNAME for OSS devices
  ALSA: hda - Add sanity check in PCM open callback
  ALSA: hda - Call snd_pcm_lib_hw_rates() again after codec open callback
  ALSA: hda - Avoid invalid formats and rates with shared SPDIF
  ALSA: hda - Improve ASUS eeePC 1000 mixer
  ALSA: hda - Add GPIO1 control at muting with HP laptops
  ALSA: usx2y - reparent sound device
  ALSA: snd_usb_caiaq: reparent sound device
  sound: virtuoso: fix Xonar D1/DX silence after resume
  ASoC: Only disable pxa2xx-i2s clocks if we enabled them
  ALSA: hda - Add quirk for HP 6930p
  ALSA: hda - Add missing static to patch_ca0110()
  ASoC: OMAP: fix OMAP1510 broken PCM pointer callback
  ASoC: remove BROKEN from Efika and pcm030 fabric drivers
  ASoC: Fix typo in MPC5200 PSC AC97 driver Kconfig

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
  kbuild: finally remove the obsolete variable $TOPDIR
  gitignore: ignore scripts/ihex2fw
  Kbuild: Disable the -Wformat-security gcc flag
  gitignore: ignore gcov output files
  kbuild: deb-pkg ship changelog
  Add new __init_task_data macro to be used in arch init_task.c files.
  asm-generic/vmlinux.lds.h: shuffle INIT_TASK* macro names in vmlinux.lds.h
  Add new macros for page-aligned data and bss sections.
  asm-generic/vmlinux.lds.h: Fix up RW_DATA_SECTION definition.

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: don't merge requests of different failfast settings
  cciss: Ignore stale commands after reboot

Occasionally we may see an interrupt without an event in the eq.
In intx, we currently see the event queue and return IRQ_NONE causing
a the irq to be disabled ("no one cared".) Instead, read the CEV_ISR
reg to check the existence of the interrupt.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This workaround is required for an issue in hardware where noise on the
interconnect between the MAC and PHY could be generated by a lower power
mode (K1) at 1000Mbps resulting in bad packets.  Disable K1 while at 1000
Mbps but keep it enabled for 10/100Mbps and when the cable is disconnected.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some PHYs may require two reads of the PHY_STATUS register to determine the
link status.  If the PHY is being accessed by another thread it is possible
the first read could timeout and fail.  In this case, put a delay in so
the second read will pick up the correct link status.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Limit NVM writes to 4K sections to prevent NVM corruption on larger
sector allocations (up to 64K).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver was accessing register bits for features on parts that do
not support that feature.  This could cause problems in the hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A previous workaround for 82578 to avoid link stall causes some PHY
registers to get cleared inadvertently.  Add a delay after all LCD resets
to make sure PHY registers are in a stable state before continuing.  Also,
after resets check the EEC register for the state of PHY configuration
performed by the MAC for ICH9 and earlier parts (as done before), but check
the LAN_INIT_DONE bit in the STATUS register for ICH10 and newer parts (EEC
doesn't exist in these newer parts).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PHY loopback on 82578 fails to work as a result of flushing the packets
in the FIFO buffer in the link stall workaround.  Don't perform the
workaround if in PHY loopback mode.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wake-on-lan is currently only supported by 82599 KX4 devices, in all
other cases return a proper value from ixgbe_wol_exclusion function call.
Otherwise from ethtool we will be able to change wol options of
unsupported 8259x devices.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently if we loaded the driver, insert an unsupported module, and then
attempt to "ifconfig up" the device it will be brought down but the netdev
would not be unregistered. This behavior is different than all other
code paths. This patch corrects that by down'ing the device and then
scheduling the sfp_config_module_task tasklet. The tasklet will detect
this condition (like it does with other code paths) and do the
unregister_netdev().

I also removed the log message as this condition (an unsupported SFP+
module) will be logged in sfp_config_module_task.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The change to check the SFP+ module again on open() was
causing the XFP (non-SFP+) adapters to be rejected. We
only want to try and re-identify the SFP+ module if the
original probe found that this device was an SFP+ device.
So for this code path (driver loaded with SFP module, module
inserted, ifconfig up of the device) the type will be
ixgbe_phy_unknown for an unidentified SFP+ module.  So we
only check if that is the case.

This problem also shows up on Copper devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>