- 29 Jul, 2005 40 commits
-
-
Michael Hund authored
below you will find the forgotten kmalloc check (sorry). Signed-off-by:
Michael Hund <mhund@ld-didactic.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Alan Stern authored
This patch handles a rarely-encountered failure mode in usbcore. It's legal for device_add to fail (although now it happens even more rarely than before since failure to bind a driver is no longer fatal). So when we destroy the interfaces in a configuration, we shouldn't try to delete ones which weren't successfully registered. Also, failure to register an interface shouldn't be fatal either -- I think; you may disagree about this part of the patch. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Adrian Bunk authored
The only uses of both variables were recently removed. Signed-off-by:
Adrian Bunk <bunk@stusta.de> Signed-off-by:
-
Alan Stern authored
This patch fixes an information leak in the usbfs snoop facility: uninitialized data from __get_free_page can be returned to userspace and written to the system log. It also improves the snoop output by printing the wLength value. Signed-off-by:
-
Ian Abbott authored
ftdi_sio: Fix timeouts in a couple of usb_control_msg() calls due to change of units from jiffies to milliseconds in 2.6.12. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
Ian Abbott authored
ftdi_sio: Update RTS and DTR simultaneously, using a single control URB instead of separate control URBs for RTS and DTR. Reinhard Bergmann observed time differences of up to 680 ms with his application on a 2.4.22 kernel when RTS and DTR were updated using separate control URBs, which is unacceptable. Signed-off-by:
-
Ian Abbott authored
The attached patch adds the following new devices to the ftdi_sio driver: * microHAM USB-Y6 and USB-Y8 devices submitted by Justin Burket (KL1RL). * Evolution Robotics ER1 Control Module submitted by Shawn M. Lavelle. Signed-off-by:
-
Kumar Gala authored
In the patch from: http://www.uwsg.iu.edu/hypermail/linux/kernel/0506.3/0985.html Is the the following line suppose inside the if CONFIG_PCI=n #define pci_dma_burst_advice(pdev, strat, strategy_parameter) do { } while (0) Signed-off-by:
Kumar Gala <kumar.gala@freescale.com> Signed-off-by:
-
Ivan Kokshaysky authored
The setup-bus code doesn't work correctly for configurations with more than one display adapter in the same PCI domain. This stuff actually is a leftover of an early 2.4 PCI setup code and apparently it stopped working after some "bridge_ctl" changes. So the best thing we can do is just to remove it and rely on the fact that any firmware *has* to configure VGA port forwarding for the boot display device properly. But then we need to ensure that the bus->bridge_ctl will always contain valid information collected at the probe time, therefore the following change in pci_scan_bridge() is needed. Signed-off-by:
Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by:
-
Jon Smirl authored
There are ROMs reporting that their size exceeds their PCI ROM resource window. This patch returns the minimum of the resource window size or the size in the ROM. An example of this breakage is the XGI Volari Z7. Signed-off-by:
Jon Smirl <jonsmirl@gmail.com> Signed-off-by:
-
Daniele Gaffuri authored
Patch against 2.6.12 to unhide SMBus on Toshiba Centrino laptops using Intel 82855PM chipset. Tested on Toshiba Tecra M2. Signed-off-by:
Daniele Gaffuri <d.gaffuri@reply.it> Signed-off-by:
-
Evgeniy Polyakov authored
This patch was sent first time very long time ago, but magically was disapeared, it probably exists in your queue, but to be sure, I resend it. If can not be applied cleanly after your w1 queue is flushed into upstrem tree, just drop it. Thanks. Patch from Michael Farmbauer <michl@baldrian.franken.de>. Signed-off-by:
Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by:
-
Jean Delvare authored
The 24RF08 corruption prevention in the eeprom and max6875 drivers wasn't complete. For one thing, the additional quick write should happen as soon as possible and unconditionally, while both drivers had error paths before. For another, when a given chip is forced, the core does not emit a quick write, so a second quick write would cause the corruption rather than prevent it. I plan to move the corruption prevention in the core in the long run, so that individual drivers don't have to care anymore. But I need to merge i2c_probe and i2c_detect before I do (work in progress). Signed-off-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Jean Delvare authored
Two log messages lack their trailing new line in i2c-core. I'd swear I had fixed them already, but it seems not. Bonus: improved coding style. Signed-off-by:
-
Jean Delvare authored
A few i2c drivers were not updated to use time_after() yet. Signed-off-by:
Marcelo Feitoza Parisi <marcelo@feitoza.com.br> Signed-off-by:
-
Jean Delvare authored
A few split string in i2c (and now hwmon) drivers lack a joining space, causing them to display incorrectly. This trivial patch fixes that up. Please apply, thanks. Signed-off-by:
-
Ladislav Michl authored
DS1339 manual, page 6, chapter Date and time operation: The DS1339 can be run in either 12-hour or 24-hour mode. Bit 6 of the hours register is defined as the 12-hour or 24-hour mode-select bit. When high, the 12-hour mode is selected. Patch below makes ds1337 driver work as documented in manual. Signed-off-by:
Ladislav Michl <ladis@linux-mips.org> Signed-off-by:
-
Kumar Gala authored
I2C-MPC: Restore code removed A previous patch to remove support for the OCP device model was way to generious and moved some of the platform device model code, oops. Signed-off-by:
-
Greg KH authored
This was the last agreed upon set of rules, it's probably time we actually add them to the kernel tree to make them "official". Signed-off-by:
-
Adrian Bunk authored
CONFIG_DEBUG_FS=y and CONFIG_SYSFS=n results in the following compile error: <-- snip --> ... LD vmlinux fs/built-in.o: In function `debugfs_init': inode.c:(.init.text+0x31be): undefined reference to `kernel_subsys' make: *** [vmlinux] Error 1 <-- snip --> Signed-off-by:
-
Maneesh Soni authored
o sysfs_dirent's s_mode field should also be updated in sysfs_setattr(), else there could be inconsistency in the two fields. s_mode is used while ->readdir so as not to bring in the inode to cache. Signed-off-by:
Maneesh Soni <maneesh@in.ibm.com> Signed-off-by:
-
Maneesh Soni authored
o sysfs_chmod_file() must update the new iattr field in sysfs_dirent else the mode change will not be persistent in case of inode evacuation from cache. Signed-off-by:
-
Daniel Walker authored
Signed-off-by:
Daniel Walker <dwalker@mvista.com> Signed-off-by:
-
Eric W. Biederman authored
Use the standard hardware page table manipulation macros. This is possible now that linux works with all 4 levels of the page tables. Signed-off-by:
Eric W. Biederman <ebiederm@xmission.com> Signed-off-by:
-
Eric W. Biederman authored
In an uncensored copy of code from i386 to x86_64 I wound up with inline assembly with the wrong constraints. Use input constraints instead of output constraints. So I know the assembler will do the right thing specify the size of the operand lidtq and lgdtq instead of just lidt and lgdt. Make load_segments use an input constraint, and delete the macro fun. Without having to reload %cs like I do on i386 this code is noticeably simpler. Signed-off-by:
-
Eric W. Biederman authored
For some reason I was telling my inline assembly that the input argument was an output argument. Playing in the trampoline code I have seen a couple of instances where lgdt get the wrong size (because the trampolines run in 16bit mode) so use lgdtl and lidtl to be explicit. Additionally gcc-3.3 and gcc-3.4 want's an lvalue for a memory argument and it doesn't think an array of characters is an lvalue so use a packed structure instead. Signed-off-by:
-
Eric W. Biederman authored
If device_suspend(PMSG_FREEZE) is not ready to be called in kernel_restart it is definitely not ready to be called in the even more fickle kernel_kexec. Signed-off-by:
-
Linus Torvalds authored
Some edge problems with the original C rewrite. Thanks go to Cal Peake, who pinpointed the breakage to the rewrite, and tested this fixed version. Signed-off-by: -
Linus Torvalds authored
-
Dave Jones authored
From: Mark Langsdorf <mark.langsdorf@amd.com> Signed-off-by:Dave Jones <davej@redhat.com>
-
Linus Torvalds authored
-
Linus Torvalds authored
-
Linus Torvalds authored
-
Russell King authored
Since the secondary CPUs will not be operating in symetric mode while they are held in the pen, we need to ensure that the write to pen_release is visible to them, by flushing the cache. Signed-off-by:Russell King <rmk+kernel@arm.linux.org.uk>
-
Linus Torvalds authored
-
Stephen Smalley authored
This patch fixes the address length checks in the selinux_socket_connect hook to be no more restrictive than the underlying ipv4 and ipv6 code; otherwise, this hook can reject valid connect calls. This patch is in response to a bug report where an application was calling connect on an INET6 socket with an address that didn't include the optional scope id and failing due to these checks. Signed-off-by:
Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by:
James Morris <jmorris@redhat.com> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
-
Jon Smirl authored
Fix a buffer overflow vunerabilty in previous cmap patch Signed-off-by:
-
Dave Hansen authored
Somewhere recently, the TSC got re-enabled for timekeeping on NUMAQ machines. However, the hardware makes these get unsynchronized quite badly. So badly, in fact, that the code to fix up the skew can just hang on boot. This patch re-disables them. It's nicely confined to the numaq.c file. It would be great if this could make it into 2.6.13, I think it counts as a bugfix. Tested on a 16-proc 4-node NUMAQ. Signed-off-by:
Dave Hansen <haveblue@us.ibm.com> Signed-off-by:
-
George Anzinger authored
(We found this (after a customer complained) and it is in the kernel.org kernel. Seems that for CLOCK_MONOTONIC absolute timers and clock_nanosleep calls both the request time and wall_to_monotonic are subtracted prior to the normalize resulting in an overflow in the existing normalize test. This causes the result to be shifted ~4 seconds ahead instead of ~2 seconds back in time.) The normalize code in posix-timers.c fails when the tv_nsec member is ~1.2 seconds negative. This can happen on absolute timers (and clock_nanosleeps) requested on CLOCK_MONOTONIC (both the request time and wall_to_monotonic are subtracted resulting in the possibility of a number close to -2 seconds.) This fix uses the set_normalized_timespec() (which does not have an overflow problem) to fix the problem and as a side effect makes the code cleaner. Signed-off-by:
George Anzinger <george@mvista.com> Signed-off-by:
-
Paolo 'Blaisorblade' Giarrusso authored
Actually implement the hostfs "sync" method. Signed-off-by:
Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by:
-
