When the vmalloc area gets fragmented, and because the firmware
mapping area sits between where modules live and the vmalloc area, we
can sometimes receive requests for enormous kernel TLB range flushes.

When this happens the cpu just spins flushing billions of pages and
this triggers the NMI watchdog and other problems.

We took care of this on the TSB side by doing a linear scan of the
table once we pass a certain threshold.

Do something similar for the TLB flush, however we are limited by
the TLB flush facilities provided by the different chip variants.

First of all we use an (mostly arbitrary) cut-off of 256K which is
about 32 pages.  This can be tuned in the future.

The huge range code path for each chip works as follows:

1) On spitfire we flush all non-locked TLB entries using diagnostic
   acceses.

2) On cheetah we use the "flush all" TLB flush.

3) On sun4v/hypervisor we do a TLB context flush on context 0, which
   unlike previous chips does not remove "permanent" or locked
   entries.

We could probably do something better on spitfire, such as limiting
the flush to kernel TLB entries or even doing range comparisons.
However that probably isn't worth it since those chips are old and
the TLB only had 64 entries.
Reported-by: James Clarke <jrtc27@jrtc27.com>
Tested-by: James Clarke <jrtc27@jrtc27.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just like the non-cross-call TLB flush handlers, the cross-call ones need
to avoid doing PC-relative branches outside of their code blocks.
Signed-off-by: David S. Miller <davem@davemloft.net>

Noticed by James Clarke.
Signed-off-by: David S. Miller <davem@davemloft.net>

If the number of pages we are flushing is more than twice the number
of entries in the TSB, just scan the TSB table for matches rather
than probing each and every page in the range.

Based upon a patch and report by James Clarke.
Signed-off-by: David S. Miller <davem@davemloft.net>

Additionally, if the offset will overflow the immediate for a ba,pt
instruction, fall back on a standard ba to get an extra 3 bits.
Signed-off-by: James Clarke <jrtc27@jrtc27.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we copy code over to patch another piece of code, we can only use
PC-relative branches that target code within that piece of code.

Such PC-relative branches cannot be made to external symbols because
the patch moves the location of the code and thus modifies the
relative address of external symbols.

Use an absolute jmpl to fix this problem.
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that all of the user copy routines are converted to return
accurate residual lengths when an exception occurs, we no longer need
the broken fixup routines.
Signed-off-by: David S. Miller <davem@davemloft.net>

All of __ret{,l}_mone{_asi,_fp,_asi_fpu} are now unused.
Signed-off-by: David S. Miller <davem@davemloft.net>

Report the exact number of bytes which have not been successfully
copied when an exception occurs, using the running remaining length.
Signed-off-by: David S. Miller <davem@davemloft.net>

Report the exact number of bytes which have not been successfully
copied when an exception occurs, using the running remaining length.
Signed-off-by: David S. Miller <davem@davemloft.net>

Report the exact number of bytes which have not been successfully
copied when an exception occurs, using the running remaining length.
Signed-off-by: David S. Miller <davem@davemloft.net>

Report the exact number of bytes which have not been successfully
copied when an exception occurs, using the running remaining length.
Signed-off-by: David S. Miller <davem@davemloft.net>

Report the exact number of bytes which have not been successfully
copied when an exception occurs, using the running remaining length.
Signed-off-by: David S. Miller <davem@davemloft.net>

Report the exact number of bytes which have not been successfully
copied when an exception occurs, using the running remaining length.
Signed-off-by: David S. Miller <davem@davemloft.net>

Report the exact number of bytes which have not been successfully
copied when an exception occurs, using the running remaining length.
Signed-off-by: David S. Miller <davem@davemloft.net>

The fixup helper function mechanism for handling user copy fault
handling is not %100 accurrate, and can never be made so.

We are going to transition the code to return the running return
return length, which is always kept track in one or more registers
of each of these routines.

In order to convert them one by one, we have to allow the existing
behavior to continue functioning.

Therefore make all the copy code that wants the fixup helper to be
used return negative one.

After all of the user copy routines have been converted, this logic
and the fixup helpers themselves can be removed completely.
Signed-off-by: David S. Miller <davem@davemloft.net>

It is completely unused.
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix [-Wold-style-declaration] GCC warnings by moving the inline keyword
before the return type.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix [-Wold-style-declaration] GCC warnings by moving the inline keyword
before the return type.
Signed-off-by: Tobias Klnuser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Individual scheduler domain should consist different hierarchy
consisting of cores sharing similar property. Currently, no
scheduler domain is defined separately for the cores that shares
the last level cache. As a result, the scheduler fails to take
advantage of cache locality while migrating tasks during load
balancing.

Here are the cpu masks currently present for sparc that are/can
be used in scheduler domain construction.
cpu_core_map : set based on the cores that shares l1 cache.
core_core_sib_map : is set based on the socket id.
The prior SPARC notion of socket was defined as highest level of
shared cache. However, the MD record on T7 platforms now describes
the CPUs that share the physical socket and this is no longer tied
to shared cache.

That's why a separate cpu mask needs to be created that truly
represent highest level of shared cache for all platforms.
Signed-off-by: Atish Patra <atish.patra@oracle.com>
Reviewed-by: Chris Hyser <chris.hyser@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull UBI[FS] fixes from Richard Weinberger:
 "This contains fixes for issues in both UBI and UBIFS:

   - Fallout from the merge window, refactoring UBI code introduced some
     issues.

   - Fixes for an UBIFS readdir bug which can cause getdents() to busy
     loop for ever and a bug in the UBIFS xattr code"

* tag 'upstream-4.9-rc2' of git://git.infradead.org/linux-ubifs:
  ubifs: Abort readdir upon error
  UBI: Fix crash in try_recover_peb()
  ubi: fix swapped arguments to call to ubi_alloc_aeb
  ubifs: Fix xattr_names length in exit paths
  ubifs: Rename ubifs_rename2

Pull ext4 fixes from Ted Ts'o:
 "A few bug fixes and add some missing KERN_CONT annotations"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: add missing KERN_CONT to a few more debugging uses
  fscrypto: lock inode while setting encryption policy
  ext4: correct endianness conversion in __xattr_check_inode()
  fscrypto: make XTS tweak initialization endian-independent
  ext4: do not advertise encryption support when disabled
  jbd2: fix incorrect unlock on j_list_lock
  ext4: super.c: Update logging style using KERN_CONT

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are the outstanding target-pending fixes for v4.9-rc2.

  This includes:

   - Fix v4.1.y+ reference leak regression with concurrent TMR
     ABORT_TASK + session shutdown. (Vaibhav Tandon)

   - Enable tcm_fc w/ SCF_USE_CPUID to avoid host exchange timeouts
     (Hannes)

   - target/user error sense handling fixes. (Andy + MNC + HCH)

   - Fix iscsi-target NOP_OUT error path iscsi_cmd descriptor leak
     (Varun)

   - Two EXTENDED_COPY SCSI status fixes for ESX VAAI (Dinesh Israni +
     Nixon Vincent)

   - Revert a v4.8 residual overflow change, that breaks sg_inq with
     small allocation lengths.

  There are a number of folks stress testing the v4.1.y regression fix
  in their environments, and more folks doing iser-target I/O stress
  testing atop recent v4.x.y code.

  There is also one v4.2.y+ RCU conversion regression related to
  explicit NodeACL configfs changes, that is still being tracked down"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target/tcm_fc: use CPU affinity for responses
  target/tcm_fc: Update debugging statements to match libfc usage
  target/tcm_fc: return detailed error in ft_sess_create()
  target/tcm_fc: print command pointer in debug message
  target: fix potential race window in target_sess_cmd_list_waiting()
  Revert "target: Fix residual overflow handling in target_complete_cmd_with_length"
  target: Don't override EXTENDED_COPY xcopy_pt_cmd SCSI status code
  target: Make EXTENDED_COPY 0xe4 failure return COPY TARGET DEVICE NOT REACHABLE
  target: Re-add missing SCF_ACK_KREF assignment in v4.1.y
  iscsi-target: fix iscsi cmd leak
  iscsi-target: fix spelling mistake "Unsolicitied" -> "Unsolicited"
  target/user: Fix comments to not refer to data ring
  target/user: Return an error if cmd data size is too large
  target/user: Use sense_reason_t in tcmu_queue_cmd_ring

Merge tag 'hwmon-for-linus-v4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Couple of hwmon fixes:

  Fix a potential ERR_PTR dereference in max31790 driver, and handle
  temperature readings below 0 in adm9240 driver"

* tag 'hwmon-for-linus-v4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (max31790) potential ERR_PTR dereference
  hwmon: (adm9240) handle temperature readings below 0

Pull IPMI updates from Corey Minyard:
 "A small bug fix and a new driver for acting as an IPMI device.

  I was on vacation during the merge window (a long vacation) but this
  is a bug fix that should go in and a new driver that shouldn't hurt
  anything.

  This has been in linux-next for a month or so"

* tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
  ipmi: fix crash on reading version from proc after unregisted bmc
  ipmi/bt-bmc: remove redundant return value check of platform_get_resource()
  ipmi/bt-bmc: add a dependency on ARCH_ASPEED
  ipmi: Fix ioremap error handling in bt-bmc
  ipmi: add an Aspeed BT IPMI BMC driver

Pull timer updates from Thomas Gleixner:
 "This updates contains:

   - A revert which addresses a boot failure on ARM Sun5i platforms

   - A new clocksource driver, which has been delayed beyond rc1 due to
     an interrupt driver issue which was unearthed by this driver. The
     debugging of that issue and the discussion about the proper
     solution made this driver miss the merge window. There is no point
     in delaying it for a full cycle as it completes the basic mainline
     support for the new JCore platform and does not create any risk
     outside of that platform"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert "clocksource/drivers/timer_sun5i: Replace code by clocksource_mmio_init"
  clocksource: Add J-Core timer/clocksource driver
  of: Add J-Core timer bindings

Pull x86 fixes from Ingo Molnar:
 "Three fixes, a hw-enablement and a cross-arch fix/enablement change:

   - SGI/UV fix for older platforms

   - x32 signal handling fix

   - older x86 platform bootup APIC fix

   - AVX512-4VNNIW (Neural Network Instructions) and AVX512-4FMAPS
     (Multiply Accumulation Single precision instructions) enablement.

   - move thread_info back into x86 specific code, to make life easier
     for other architectures trying to make use of
     CONFIG_THREAD_INFO_IN_TASK_STRUCT=y"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/smp: Don't try to poke disabled/non-existent APIC
  sched/core, x86: Make struct thread_info arch specific again
  x86/signal: Remove bogus user_64bit_mode() check from sigaction_compat_abi()
  x86/platform/UV: Fix support for EFI_OLD_MEMMAP after BIOS callback updates
  x86/cpufeature: Add AVX512_4VNNIW and AVX512_4FMAPS features
  x86/vmware: Skip timer_irq_works() check on VMware

Pull vmap stack fixes from Ingo Molnar:
 "This is fallout from CONFIG_HAVE_ARCH_VMAP_STACK=y on x86: stack
  accesses that used to be just somewhat questionable are now totally
  buggy.

  These changes try to do it without breaking the ABI: the fields are
  left there, they are just reporting zero, or reporting narrower
  information (the maps file change)"

* 'mm-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  mm: Change vm_is_stack_for_task() to vm_is_stack_for_current()
  fs/proc: Stop trying to report thread stacks
  fs/proc: Stop reporting eip and esp in /proc/PID/stat
  mm/numa: Remove duplicated include from mprotect.c

Pull irq fixes from Ingo Molnar:
 "Mostly irqchip driver fixes, plus a symbol export"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  kernel/irq: Export irq_set_parent()
  irqchip/gic: Add missing \n to CPU IF adjustment message
  irqchip/jcore: Don't show Kconfig menu item for driver
  irqchip/eznps: Drop pointless static qualifier in nps400_of_init()
  irqchip/gic-v3-its: Fix entry size mask for GITS_BASER
  irqchip/gic-v3-its: Fix 64bit GIC{R,ITS}_TYPER accesses

Pull EFI fixes from Ingo Molnar:
 "Add Ard Biesheuvel as EFI co-maintainer, plus fix an ARM build bug
  with older toolchains"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/arm: Fix absolute relocation detection for older toolchains
  MAINTAINERS: Add myself as EFI maintainer

Apparently trying to poke a disabled or non-existent APIC
leads to a box that doesn't even boot. Let's not do that.

No real clue if this is the right fix, but at least my
P3 machine boots again.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: dyoung@redhat.com
Cc: kexec@lists.infradead.org
Cc: stable@vger.kernel.org
Fixes: 2a51fe08 ("arch/x86: Handle non enumerated CPU after physical hotplug")
Link: http://lkml.kernel.org/r/1477102684-5092-1-git-send-email-ville.syrjala@linux.intel.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Pull powerpc fixes from Michael Ellerman:
 "Fixes marked for stable:
   - Prevent unlikely crash in copro_calculate_slb() (Frederic Barrat)
   - cxl: Prevent adapter reset if an active context exists (Vaibhav Jain)

  Fixes for code merged this cycle:
   - Fix boot on systems with uncompressed kernel image (Heiner Kallweit)
   - Drop dump_numa_memory_topology() (Michael Ellerman)
   - Fix numa topology console print (Aneesh Kumar K.V)
   - Ignore the pkey system calls for now (Stephen Rothwell)"

* tag 'powerpc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Ignore the pkey system calls for now
  powerpc: Fix numa topology console print
  powerpc/mm: Drop dump_numa_memory_topology()
  cxl: Prevent adapter reset if an active context exists
  powerpc/boot: Fix boot on systems with uncompressed kernel image
  powerpc/mm: Prevent unlikely crash in copro_calculate_slb()

Pull KVM fixes from Radim Krčmář:
 "ARM:
   - avoid livelock when walking guest page tables
   - fix HYP mode static keys without CC_HAVE_ASM_GOTO

  MIPS:
   - fix a build error without TRACEPOINTS_ENABLED

  s390:
   - reject a malformed userspace configuration

  x86:
   - suppress a warning without CONFIG_CPU_FREQ
   - initialize whole irq_eoi array"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  arm/arm64: KVM: Map the BSS at HYP
  arm64: KVM: Take S1 walks into account when determining S2 write faults
  KVM: s390: reject invalid modes for runtime instrumentation
  kvm: x86: memset whole irq_eoi
  kvm/x86: Fix unused variable warning in kvm_timer_init()
  KVM: MIPS: Add missing uaccess.h include

Pull NFS client bugfixes from Anna Schumaker:
 "Just two bugfixes this time:

  Stable bugfix:
   - Fix last_write_offset incorrectly set to page boundary

  Other bugfix:
   - Fix missing-braces warning"

* tag 'nfs-for-4.9-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  nfs4: fix missing-braces warning
  pnfs/blocklayout: fix last_write_offset incorrectly set to page boundary

Pull ACPI fixes from Rafael Wysocki:
 "These fix an issue related to system resume in the new WDAT-based
  watchdog driver and a return value of a stub function in the ACPI CPPC
  framework.

  Specifics:

   - Update the ACPI WDAT-based watchdog driver to ping the hardware
     during system resume to prevent a reset from occurring after the
     resume is complete (Mika Westerberg).

   - Fix the return value of the pcc_mbox_request_channel() stub for
     CONFIG_PCC unset (Hoan Tran)"

* tag 'acpi-4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  watchdog: wdat_wdt: Ping the watchdog on resume
  mailbox: PCC: Fix return value of pcc_mbox_request_channel()

* acpi-wdat:
  watchdog: wdat_wdt: Ping the watchdog on resume

* acpi-cppc:
  mailbox: PCC: Fix return value of pcc_mbox_request_channel()

Merge tag 'gic-fixes-for-4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent

Pull GIC updates from Marc Zyngier:

 - Fix for 32bit accesses that should be 64bit on 64bit machines
 - Fix for a field decoding macro
 - Beautify a warning message

Pull SCSI fixes from James Bottomley:
 "Five small fixes.

  Some of these, like the nested spinlock overwriting saved flags and
  the Kasan use after free look serious, but they seem not to have been
  picked up in testing or seen in the field.

  The biggest user visible issue is probably the wrong device handler
  for Clariion, which means that alua doesn't bind to the array like it
  should"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ipr: Fix async error WARN_ON
  scsi: zfcp: spin_lock_irqsave() is not nestable
  scsi: Remove one useless stack variable
  scsi: Fix use-after-free
  scsi: Replace wrong device handler name for CLARiiON arrays

Pull block fixes from Jens Axboe:
 "A set of fixes that missed the merge window, mostly due to me being
  away around that time.

  Nothing major here, a mix of nvme cleanups and fixes, and one fix for
  the badblocks handling"

* 'for-linus' of git://git.kernel.dk/linux-block:
  nvmet: use symbolic constants for CNS values
  nvme: use symbolic constants for CNS values
  nvme.h: add an enum for cns values
  nvme.h: don't use uuid_be
  nvme.h: resync with nvme-cli
  nvme: Add tertiary number to NVME_VS
  nvme : Add sysfs entry for NVMe CMBs when appropriate
  nvme: don't schedule multiple resets
  nvme: Delete created IO queues on reset
  nvme: Stop probing a removed device
  badblocks: fix overlapping check for clearing