* 'for-linus' of git://git.kernel.dk/linux-block:
  block: fix warning with calling smp_processor_id() in preemptible section

* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (135 commits)
  drm/radeon/kms: fix DP training for DPEncoderService revision bigger than 1.1
  drm/radeon/kms: add missing vddci setting on NI+
  drm/radeon: Add a rmb() in IH processing
  drm/radeon: ATOM Endian fix for atombios_crtc_program_pll()
  drm/radeon: Fix the definition of RADEON_BUF_SWAP_32BIT
  drm/radeon: Do an MMIO read on interrupts when not uisng MSIs
  drm/radeon: Writeback endian fixes
  drm/radeon: Remove a bunch of useless _iomem casts
  drm/gem: add support for private objects
  DRM: clean up and document parsing of video= parameter
  DRM: Radeon: Fix section mismatch.
  drm: really make debug levels match in edid failure code
  drm/radeon/kms: fix i2c map for rv250/280
  drm/nouveau/gr: disable fifo access and idle before suspend ctx unload
  drm/nouveau: pass flag to engine fini() method on suspend
  drm/nouveau: replace nv04_graph_fifo_access() use with direct reg bashing
  drm/nv40/gr: rewrite/split context takedown functions
  drm/nouveau: detect disabled device in irq handler and return IRQ_NONE
  drm/nouveau: ignore connector type when deciding digital/analog on DVI-I
  drm/nouveau: Add a quirk for Gigabyte NX86T
  ...

After commit 5757a6d7 introduced an unsafe calling of
smp_processor_id(), with preempt debuggin turned on we spew a lot of:

BUG: using smp_processor_id() in preemptible [00000000] code: kjournald/514
caller is __make_request+0x1b8/0x308
[<c0019f44>] (unwind_backtrace+0x0/0xe8) from [<c024b4cc>] (debug_smp_processor_id+0xbc/0xf0)
[<c024b4cc>] (debug_smp_processor_id+0xbc/0xf0) from [<c0223d14>] (__make_request+0x1b8/0x308)
[<c0223d14>] (__make_request+0x1b8/0x308) from [<c02215ac>] (generic_make_request+0x4dc/0x558)
[<c02215ac>] (generic_make_request+0x4dc/0x558) from [<c022173c>] (submit_bio+0x114/0x138)
[<c022173c>] (submit_bio+0x114/0x138) from [<c011f504>] (submit_bh+0x148/0x16c)
[<c011f504>] (submit_bh+0x148/0x16c) from [<c0121ed8>] (__sync_dirty_buffer+0x88/0xd8)
[<c0121ed8>] (__sync_dirty_buffer+0x88/0xd8) from [<c01aff78>] (journal_commit_transaction+0x1198/0x1688)
[<c01aff78>] (journal_commit_transaction+0x1198/0x1688) from [<c01b4034>] (kjournald+0xb4/0x224)
[<c01b4034>] (kjournald+0xb4/0x224) from [<c0069ea0>] (kthread+0x8c/0x94)
[<c0069ea0>] (kthread+0x8c/0x94) from [<c00137f8>] (kernel_thread_exit+0x0/0x8)

Fix this by just using raw_smp_processor_id(), it's just a hint
after all. There's no pinning of the CPU or accessing per-cpu
structures involved.
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

DPEncoderService newer than 1.1 can't properly program the DP (display port)
link training. When facing such version use the DIGxEncoderControl method
instead. Fix DP link training on some R7XX.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Need to add vddci setting to pm init as well as
resume.  Fixes hangs on load on some boards.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=38754Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Commit 4e34e719 ("fs: take the ACL checks to common code") removed
the use of the 'acl' variable in v9fs_iop_get_acl(), but left the
variable definition around.  Remove it to get rid of the warning:

  fs/9p/acl.c: In function ‘v9fs_iop_get_acl’:
  fs/9p/acl.c:101:20: warning: unused variable ‘acl’
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (741 commits)
  staging:iio:meter:ade7753 should be 16 bit read not 8 bit for mode register.
  staging:iio:kfifo_buf fix double initialization of the ring device structure.
  staging:iio:accel:lis3l02dq: fix incorrect pointer passed to spi_set_drvdata.
  staging:iio:imu fix missing register table index for some channels
  spectra: enable device before poking it
  staging: rts_pstor: Fix a miswriting
  staging/lirc_bt829: Return -ENODEV when no hardware is found.
  staging/lirc_parallel: remove pointless prototypes.
  staging/lirc_parallel: fix panic on rmmod
  staging:iio:adc:ad7476: Incorrect pointer into spi_set_drvdata.
  Staging: zram: Fix kunmapping order
  Revert "gma500: Fix dependencies"
  gma500: Add medfield header
  gma500: wire up the mrst i2c bus from chip_info
  gma500: Fix DPU build
  gma500: Clean up the DPU config and make it runtime
  gma500: resync with Medfield progress
  gma500: Use the mrst helpers and power control for mode commit
  gma500@ Fix backlight range error
  gma500: More Moorestown muddle meddling means MM maybe might modeset
  ...

Fix up fairly trivial conflicts all over, mostly due to header file
cleanup conflicts, but some deleted files and some just context changes:
 - Documentation/feature-removal-schedule.txt
 - drivers/staging/bcm/headers.h
 - drivers/staging/brcm80211/brcmfmac/dhd_linux.c
 - drivers/staging/brcm80211/brcmfmac/dhd_sdio.c
 - drivers/staging/brcm80211/brcmfmac/wl_cfg80211.h
 - drivers/staging/brcm80211/brcmfmac/wl_iw.c
 - drivers/staging/et131x/et131x_netdev.c
 - drivers/staging/rtl8187se/ieee80211/ieee80211_softmac.c
 - drivers/staging/rtl8192e/r8192E.h
 - drivers/staging/usbip/userspace/src/utils.h

* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (26 commits)
  amba pl011: workaround for uart registers lockup
  n_gsm: fix the wrong FCS handling
  pch_uart: add missing comment about OKI ML7223
  pch_uart: Add MSI support
  tty: fix "IRQ45: nobody cared"
  PTI feature to allow user to name and mark masterchannel request.
  0 for o PTI Makefile bug.
  tty: serial: samsung.c remove legacy PM code.
  SERIAL: SC26xx: Fix link error.
  serial: mrst_max3110: initialize waitqueue earlier
  mrst_max3110: Change max missing message priority.
  tty: s5pv210: Add delay loop on fifo reset function for UART
  tty/serial: Fix XSCALE serial ports, e.g. ce4100
  serial: bfin_5xx: fix off-by-one with resource size
  drivers/tty: use printk_ratelimited() instead of printk_ratelimit()
  tty: n_gsm: Added refcount usage to gsm_mux and gsm_dlci structs
  tty: n_gsm: Add raw-ip support
  tty: n_gsm: expose gsmtty device nodes at ldisc open time
  pch_phub: Fix register miss-setting issue
  serial: 8250, increase PASS_LIMIT
  ...

* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (115 commits)
  EHCI: fix direction handling for interrupt data toggles
  USB: serial: add IDs for WinChipHead USB->RS232 adapter
  USB: OHCI: fix another regression for NVIDIA controllers
  usb: gadget: m66592-udc: add pullup function
  usb: gadget: m66592-udc: add function for external controller
  usb: gadget: r8a66597-udc: add pullup function
  usb: renesas_usbhs: support multi driver
  usb: renesas_usbhs: inaccessible pipe is not an error
  usb: renesas_usbhs: care buff alignment when dma handler
  USB: PL2303: correctly handle baudrates above 115200
  usb: r8a66597-hcd: fixup USB_PORT_STAT_C_SUSPEND shift
  usb: renesas_usbhs: compile/config are rescued
  usb: renesas_usbhs: fixup comment-out
  usb: update email address in ohci-sh and r8a66597-hcd
  usb: r8a66597-hcd: add function for external controller
  EHCI: only power off port if over-current is active
  USB: mon: Allow to use usbmon without debugfs
  USB: EHCI: go back to using the system clock for QH unlinks
  ehci: add pci quirk for Ordissimo and RM Slate 100 too
  ehci: refactor pci quirk to use standard dmi_check_system method
  ...

Fix up trivial conflicts in Documentation/feature-removal-schedule.txt

Merge branch 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6

* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  updated Documentation/ja_JP/SubmittingPatches
  debugfs: add documentation for debugfs_create_x64
  uio: uio_pdrv_genirq: Add OF support
  firmware: gsmi: remove sysfs entries when unload the module
  Documentation/zh_CN: Fix messy code file email-clients.txt
  driver core: add more help description for "path to uevent helper"
  driver-core: modify FIRMWARE_IN_KERNEL help message
  driver-core: Kconfig grammar corrections in firmware configuration
  DOCUMENTATION: Replace create_device() with device_create().
  DOCUMENTATION: Update overview.txt in Doc/driver-model.
  pti: pti_tty_install documentation mispelling.

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
  drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
  powerpc/85xx: fix mpic configuration in CAMP mode
  powerpc: Copy back TIF flags on return from softirq stack
  powerpc/64: Make server perfmon only built on ppc64 server devices
  powerpc/pseries: Fix hvc_vio.c build due to recent changes
  powerpc: Exporting boot_cpuid_phys
  powerpc: Add CFAR to oops output
  hvc_console: Add kdb support
  powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
  powerpc/irq: Quieten irq mapping printks
  powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
  powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
  powerpc: Disable IRQs off tracer in ppc64 defconfig
  powerpc: Sync pseries and ppc64 defconfigs
  powerpc/pseries/hvconsole: Fix dropped console output
  hvc_console: Improve tty/console put_chars handling
  powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
  powerpc/mm: Fix output of total_ram.
  powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
  powerpc: Correct annotations of pmu registration functions
  ...

Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68k: Revive reporting of spurious interrupts
  m68knommu: Move forward declaration of do_IRQ() from machdep.h to irq.h
  m68k: fix some atomic operation asm address modes for ColdFire
  m68k: use CPU_HAS_NO_BITFIELDS for signal functions
  m68k: merge and clean up delay.h files
  m68knommu: correctly use trap_init
  m68knommu: merge ColdFire 5206 and 5206e platform code
  m68k: merge mmu and non-mmu bitops.h
  m68k: merge MMU and non MMU versions of system.h
  m68k: merge MMU and non-MMU versions of asm/hardirq.h
  m68k: merge the non-mmu and mmu versions of module.c
  m68knommu: Fix printk() format in free_initrd_mem()
  m68knommu: Make empty_zero_page "void *", like on m68k

* git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-linus:
  Squashfs: Make ZLIB compression support optional
  Squashfs: Update documentation for XZ and add squashfs-tools devel tree

* 'for-3.1' of git://linux-nfs.org/~bfields/linux:
  nfsd: don't break lease on CLAIM_DELEGATE_CUR
  locks: rename lock-manager ops
  nfsd4: update nfsv4.1 implementation notes
  nfsd: turn on reply cache for NFSv4
  nfsd4: call nfsd4_release_compoundargs from pc_release
  nfsd41: Deny new lock before RECLAIM_COMPLETE done
  fs: locks: remove init_once
  nfsd41: check the size of request
  nfsd41: error out when client sets maxreq_sz or maxresp_sz too small
  nfsd4: fix file leak on open_downgrade
  nfsd4: remember to put RW access on stateid destruction
  NFSD: Added TEST_STATEID operation
  NFSD: added FREE_STATEID operation
  svcrpc: fix list-corrupting race on nfsd shutdown
  rpc: allow autoloading of gss mechanisms
  svcauth_unix.c: quiet sparse noise
  svcsock.c: include sunrpc.h to quiet sparse noise
  nfsd: Remove deprecated nfsctl system call and related code.
  NFSD: allow OP_DESTROY_CLIENTID to be only op in COMPOUND

Fix up trivial conflicts in Documentation/feature-removal-schedule.txt

Commit e77819e5 ("vfs: move ACL cache lookup into generic code")
didn't take the FS_POSIX_ACL config variable into account - when that is
not set, ACL's go away, and the cache helper functions do not exist,
causing compile errors like

  fs/namei.c: In function 'check_acl':
  fs/namei.c:191:10: error: implicit declaration of function 'negative_cached_acl'
  fs/namei.c:196:2: error: implicit declaration of function 'get_cached_acl'
  fs/namei.c:196:6: warning: assignment makes pointer from integer without a cast
  fs/namei.c:212:11: error: implicit declaration of function 'set_cached_acl'
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* Merge akpm patch series: (122 commits)
  drivers/connector/cn_proc.c: remove unused local
  Documentation/SubmitChecklist: add RCU debug config options
  reiserfs: use hweight_long()
  reiserfs: use proper little-endian bitops
  pnpacpi: register disabled resources
  drivers/rtc/rtc-tegra.c: properly initialize spinlock
  drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
  drivers/rtc: add support for Qualcomm PMIC8xxx RTC
  drivers/rtc/rtc-s3c.c: support clock gating
  drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
  init: skip calibration delay if previously done
  misc/eeprom: add eeprom access driver for digsy_mtc board
  misc/eeprom: add driver for microwire 93xx46 EEPROMs
  checkpatch.pl: update $logFunctions
  checkpatch: make utf-8 test --strict
  checkpatch.pl: add ability to ignore various messages
  checkpatch: add a "prefer __aligned" check
  checkpatch: validate signature styles and To: and Cc: lines
  checkpatch: add __rcu as a sparse modifier
  checkpatch: suggest using min_t or max_t
  ...

Did this as a merge because of (trivial) conflicts in
 - Documentation/feature-removal-schedule.txt
 - arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.

Fix the warning

  drivers/connector/cn_proc.c: In function 'proc_ptrace_connector':
  drivers/connector/cn_proc.c:176: warning: unused variable 'tracer'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There have been persistent lockdep RCU splats, indicating that submitters
are not testing with CONFIG_PROVE_RCU.  Add this config option to the list
in Documentation/SubmitChecklist.  Also add CONFIG_DEBUG_OBJECTS_RCU_HEAD
for good measure.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use hweight_long() to count free bits in the bitmap.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Using __test_and_{set,clear}_bit_le() with ignoring its return value can
be replaced with __{set,clear}_bit_le().

This introduces reiserfs_{set,clear}_le_bit for __{set,clear}_bit_le and
does the above change with them.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When parsing PnP ACPI resource structures, it may happen that some of
the resources are disabled (in which case "the size" of the resource
equals zero).

The current solution is to skip these resources completely - with the
unfortunate side effect that they are not registered despite the fact
that they exist, after all.  (The downside of this approach is that
these resources cannot be used as templates for setting the actual
device's resources because they are missing from the template.) The
kernel's APM implementation does not suffer from this problem and
registers all resources regardless of "their size".

This patch fixes a problem with (at least) the vintage IBM ThinkPad 600E
(and most likely also with the 600, 600X, and 770X which have a very
similar layout) where some of its PnP devices support options where
either an IRQ, a DMA, or an IO port is disabled.  Without this patch,
the devices can not be configured using the
"/sys/bus/pnp/devices/*/resources" interface.

The manipulation of these resources is important because the 600E has
very demanding requirements.  For instance, the number of IRQs is not
sufficient to support all devices of the 600E.  Fortunately, some of the
devices, like the sound card's MPU-401 UART, can be configured to not
use any IRQ, hence freeing an IRQ for a device that requires one.
(Still, the device's "ResourceTemplate" requires an IRQ resource
descriptor which cannot be created if the resource has not been
registered in the first place.)

As an example, the dependent sets of the 600E's CSC0103 device (the
MPU-401 UART) are listed, with the patch applied, as:

  Dependent: 00 - Priority preferred
    port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
    irq <none> High-Edge
  Dependent: 01 - Priority acceptable
    port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
    irq 5,7,2/9,10,11,15 High-Edge

(The same result is obtained when PNPBIOS is used instead of PnP ACPI.)
Without the patch, the IRQ resource in the preferred option is not
listed at all:

  Dependent: 00 - Priority preferred
    port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
  Dependent: 01 - Priority acceptable
    port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
    irq 5,7,2/9,10,11,15 High-Edge

And in fact, the 600E's DSDT lists the disabled IRQ as an option, as can
be seen from the following excerpt from the DSDT:

	Name (_PRS, ResourceTemplate ()
	{
        StartDependentFn (0x00, 0x00)
        {
            IO (Decode16, 0x0300, 0x0330, 0x10, 0x04)
            IRQNoFlags () {}
        }
        StartDependentFn (0x01, 0x00)
        {
            IO (Decode16, 0x0300, 0x0330, 0x10, 0x04)
            IRQNoFlags () {5,7,9,10,11,15}
        }
        EndDependentFn ()
	})

With this patch applied, a user space program - or maybe even the kernel
- can allocate all devices' resources optimally.  For the 600E, this
means to find optimal resources for (at least) the serial port, the
parallel port, the infrared port, the MWAVE modem, the sound card, and
the MPU-401 UART.

The patch applies the idea to register disabled resources to all types
of resources, not just to IRQs, DMAs, and IO ports.  At the same time,
it mimics the behavior of the "pnp_assign_xxx" functions from
"drivers/pnp/manager.c" where resources with "no size" are considered
disabled.

No regressions were observed on hardware that does not require this
patch.

The patch is applied against 2.6.39.

NB: The kernel's current PnP interface does not allow for disabling individual
resources using the "/sys/bus/pnp/devices/$device/resources" file.  Assuming
this could be done, a device could be configured to use a disabled resource
using a simple series of calls:

  echo disable > /sys/bus/pnp/devices/$device/resources
  echo clear > /sys/bus/pnp/devices/$device/resources
  echo set irq disabled > /sys/bus/pnp/devices/$device/resources
  echo fill > /sys/bus/pnp/devices/$device/resources
  echo activate > /sys/bus/pnp/devices/$device/resources

This patch addresses only the parsing of PnP ACPI devices.

ChangeLog (v1 -> v2):
 - extend patch description
 - fix typo in patch itself
Signed-off-by: Witold Szczeponik <Witold.Szczeponik@gmx.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <abelay@mit.edu>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Using __SPIN_LOCK_UNLOCKED for a dynamically allocated lock is wrong and
breaks the build with PREEMPT_RT_FULL.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Andrew Chew <achew@nvidia.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We forget to save the return value of the call to
twl_rtc_write_u8(save_control, REG_RTC_CTRL_REG); in 'ret', making the
test of 'ret < 0' dead code since 'ret' then couldn't possibly have
changed since the last test just a few lines above.  It also makes us not
detect failures from that specific twl_rtc_write_u8() call.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Rusev <source@mvista.com>
Cc: "George G. Davis" <gdavis@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add support for PMIC8xxx based RTC.  PMIC8xxx is Qualcomm's power
management IC that internally houses an RTC module.  This driver
communicates with the PMIC module over SSBI bus.

[akpm@linux-foundation.org: cosmetic tweaks]
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add support for clock gating.  Power consumption can be reduced by setting
rtc_clk disabled state except for when RTC related registers are accessed.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ben Dooks <ben@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MPC5200B contains a limited version of RTC from MPC5121.  Add support for
the RTC on that CPU.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

For each CPU, do the calibration delay only once.  For subsequent calls,
use the cached per-CPU value of loops_per_jiffy.

This saves about 200ms of resume time on dual core Intel Atom N5xx based
systems.  This helps bring down the kernel resume time on such systems
from about 500ms to about 300ms.

[akpm@linux-foundation.org: make cpu_loops_per_jiffy static]
[akpm@linux-foundation.org: clean up message text]
[akpm@linux-foundation.org: fix things up after upstream rmk changes]
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Cc: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Andrew Worsley <amworsley@gmail.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Both displays on digsy_mtc board obtain their configuration from microwire
EEPROMs which are connected to the SoC over GPIO lines.  We need an easy
way to access the EEPROMs to write the needed display configuration or to
read out the currently programmed configuration.  The generic
eeprom_93xx46 SPI driver added by previous patch allows EEPROM access over
sysfs.  Using the simple driver added by this patch we provide used GPIO
interface and access control description on the board for generic
eeprom_93xx46 driver and spi_gpio driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add EEPROM driver for 93xx46 chips.  It can also be used with spi_gpio
driver to access 93xx46 EEPROMs connected over GPIO lines.  This driver
supports read/write/erase access to the EEPROM chips over sysfs files.

[rdunlap@xenotime.net: fix printk format]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Previous behavior allowed only alphabetic prefixes like pr_info to exceed
the 80 column line length limit.

ath6kl wants to add a digit into the prefix, so allow numbers as well as
digits in the <prefix>_<level> printks.

<prefix>_<level>_ratelimited and <prefix>_<level>_once and WARN_RATELIMIT
and WARN_ONCE may now exceed 80 cols.

Add missing <prefix>_printk type for completeness.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Some patches are sent in using ISO-8859 or even Windows codepage 1252.

Make checkpatch accept these by default and only emit the "Invalid UTF-8"
message when using --strict.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Some users would like the ability to not emit some of the messages that
checkpatch produces.  This can make it easier to use checkpatch in other
projects and integrate into scm hook scripts.

Add command line option to "--ignore" various message types.  Add option
--show-types to emit the "type" of each message.  Categorize all ERROR,
WARN and CHK messages with types.

Add optional .checkpatch.conf file to store default options.
3 paths are searched for .checkpatch.conf
    .             customized per-tree configurations
    $HOME         user global configuration when per-tree configs don't exist
    ./scripts     lk defaults to override script
The .conf file can contain any valid command-line argument and
the contents are prepended to any additional command line arguments.
Multiple lines may be used, blank lines are ignored, # is a comment.

Update "false positive" output for readability.

Update version to 0.32
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Prefer the use of __aligned(size) over __attribute__((__aligned___(size)))

Link: http://lkml.kernel.org/r/20110609094526.1571774c.akpm@linux-foundation.orgSuggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signatures have many forms and can sometimes cause problems if not in the
correct format when using git send-email or quilt.

Try to verify the signature tags and email addresses to use the generally
accepted "Signed-off-by: Full Name <email@domain.tld>" form.

Original idea by Anish Kumar <anish198519851985@gmail.com>
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Anish Kumar <anish198519851985@gmail.com>
Cc: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix "need consistent spacing around '*'" error after a __rcu sparse
annotation which was caused by the missing __rcu entry in the
checkpatch.pl internal list of sparse keywords.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A common issue with min() or max() is using a cast on one or both of the
arguments when using min_t/max_t could be better.

Add cast detection to uses of min/max and suggest an appropriate use of
min_t or max_t instead.

Caveat:  This only works for min() or max() on a single line.
         It does not find min() or max() split across multiple lines.

This does find:
	min((u32)foo, bar);
But it does not find:
	max((unsigned long)foo,
	    bar);
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix module tainting message:

  sigma: module license 'unspecified' taints kernel.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This function is required by *printf and kstrto* functions that are
located in the different modules.  This patch makes _tolower() public.
However, it's good idea to not use the helper outside of mentioned
functions.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The symbol 'lcm' is exported to the kernel (EXPORT_SYMBOL_GPL).
Pick up it's definition in <linux/lcm.h> to quiet the sparse noise:

  warning: symbol 'lcm' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

From: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>

platform data for simple backlight driver for LM3530
in the u5500 platform
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>