au0828: Cleanup
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

consolidate au8522_qam256_mse2snr_lookup, au8522_qam64_mse2snr_lookup and
au8522_vsb_mse2snr_lookup into a single function, au8522_mse2snr_lookup.

Pass the mse2snr table into au8522_mse2snr_lookup depending on the
modulation type.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

au8522: Added SNR support and basic cleanup
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

add function au8522_read_mse, which will be used to compute snr

TO DO: mse2snr
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

ucblocks are reported in separate registers for vsb & qam
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

replace __FUNCTION__ with __func__ and clean associated checkpatch.pl warnings.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Fixed some checkpatch.pl warnings
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

replace __FUNCTION__ with __func__ and clean associated checkpatch.pl
warnings.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

VIDEO_AU0828 should select DVB_AU8522 and DVB_TUNER_XC5000 if !DVB_FE_CUSTOMIZE
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Avoid an oops if the board is not fully defined.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Scripts to maintain the CARDLIST file.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

HVR950Q Hauppauge eeprom support.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Including support for the AU0828 USB Bridge.
Including support for the AU8522 ATSC/QAM Demodulator.
Including support for the AU8522 ATSC/QAM Demodulator.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Adding support for a new i2c bridge type
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Thanks to Aidan Thornton <makosoft@googlemail.com> for helping
to test this firmware
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

The setup is already done at open().
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

The driver should be switched to digital mode, when trying to access the
frontend or when streaming.

This patch provides the correct code to support this feature.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Before this patch,  HVR900/HVR950 were incorreclty going back to analog. The
result is that only digital were working.

This patch provides the proper setup for analog/digital and tuner callback.
It also properly resets analog into a sane state at open().

Thanks to Steven Toth <stoth@linuxtv.org> and Michael Krufky <mkrufky@linuxtv.org>
for helping to set the proper parameters to GPO/GPIO em2883 ports.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Those printk's were adding more info to a line that were already being
printed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Now, all registers will follow the same convension:

EM28XX_R<reg_number>_<reg_name>

This allows to associate a register with its value, and also with a canonical
name. Also, registers that are specific to a given chip were renamed accordingly,
as EM2800_foo (for 2800 only registers) or EM2880_foo (for registers that started
to appear on em2880).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Before this patch, registers 0x04 and 0x08 were referenced by its value. This is
bad, since makes harder for someone to understand what this is doing.

This patch renames those two registers into an appropriate name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

em28xx.h contains lots of different stuff inside. The better is to break it on
some files.

This patch removes the register names, moving them to a separate file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

This is more conservative than just removing the msleep() from
em28xx_write_regs_req(), since some old hardware may still need it.
So, it will remove the sleep time only for those chips where this
removal were tested.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

em28xx-core.c:
 - Remove sleep in i2c message routine which slows down i2c by a factor
   10x.  Load time for BASE firmware went from 13s to .973s
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

em28xx-dvb.c:
 - Remove unneeded xc3028_ctrl structure.  The driver automatically preserves
   the previous value

tuner-xc2028.c:
 - Make the return type for xc2028_get_reg signed, since all of the callers
   are looking for "< 0" to detect errors.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

xc3028_sleep function is being used with a different meaning. This
should be called only before doing S1/S3 sleep.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

The analog entries are wrong. Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Modifies em28xx-dvb not to use videobuf-dvb, but instead to include the code
for registering dvb devices locally and use the URB management code in the
em28xx driver directly. DVB data streaming should now work.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Move the URB setup and management code to em28xx-core.c and generalise
it slighlty so that the DVB code can use it.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Adds the correct GPIOs and demod attach code for the HVR-900
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

This will make tuner-xc2028 to change to analog, if needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Thanks to Devin Heitmueller <devin.heitmueller@gmail.com> for pointing
this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

em28xx-cards.c:
 - Fix reversed val/rst values in both analog_gpio and digital_gpio
   vectors
 - Fix crash that would was occurring during every analog startup
   while looping over gpio_ctl
 - Remove what appears to be a redundant setting of gpio_ctl->val
 - Don't use OREN538 demodulation for the HVR-950 (prevents ATSC
   scanning from working)

em28xx-dvb.c:
 - Tuner should be in digital mode when issuing the reset
 - Add copyright
 - Change struct definition (corresponds to fix in em28xx-cards.c for
   gpio_ctl looping)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Thanks to Devin Heitmueller <devin.heitmueller@gmail.com> and Aidan
Thornton" <makosoft@googlemail.com> for pointing some errors with the
previous scenario.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

This patch adds DVB support for Hauppauge HVR950.

Thanks to Michael Krufky <mkrufky@linuxtv.org> for getting those values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

em28xx based devices with xc3028 may require some specific gpio values.
This patch adds a generic handling for such values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>