Change Details:
	- Retrieve the VLAN configuration from the networking stack
	and apply it to the base interface during ifconfig up
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Remove unused APIs and code cleanup
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Added a check in ioc firmware lock function to see if IOC is
	in BFI_IOC_UNINIT state or not. If it is not in UNINIT state
	and the last IOC boot was not done by OS driver, force IOC state
	to BFI_IOC_UNINIT
	- Unused macro and API cleanup
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Call netif_wake_queue() if we have freed up sufficient elements
	at the end of completion processing
	- Add netif_queue_stopped counter back to bnad_drv_stats {}
	- Get netif_queue_stopped value from stack
	- Remove BUG_ON() on value returned by pci_unmap_addr()
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Enable reception of pure priority tagged packets by default by
	turning on VLAN Id = 0
	- Clear the promiscuous mode, all multicast mode flags when
	bna_rxf_uninit is called
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Removed semaphore register dump from ethtool
	- Moved netif_carrier_off() call to before calling bna_init()
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Fixed port enable/disable sync through a change in LL port state
	machine
	- Change txq->priority masking to 0x7 (3 bits) from 0x3 (2 bits)
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change Details:
	- Check HW ready condition before accessing h/w register in data-path
	- Postpone clean-up of data buffers to the data-path restart path and
	wait in the cleanup routines for in-flight DMA to complete
	- Separate out Tx completion processing from Rx poll routine
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Connection ID (cid) management
- Slow-path command and response support
- Update version to 2.2.11.
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The kcq2 (2nd kernel work queue) is used by FCoE on 57712 devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we get a path_resp error from userspace, call cm_connect_complete()
immediately with error so that bnx2i can react to the error faster.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the device is down, the kcq pointer may be NULL.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a common function cnic_read_bnx2x_iscsi_mac() to read the iSCSI
MAC address at any specified shared memory location.  In NIC Partition
mode, we need to get the MAC address from the MF_CFG area of shared
memory.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the IDs specified by the bnx2x driver when initializing the ring.
We don't have to make code changes when these IDs change in the future.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Change first parameter from cnic_dev to ulp_handle which is the hba
pointer.  All other similar upcalls are using hba pointer.  The callee
can then directly reference the hba without conversion.

2. Change return value from void to int so that an error code can be
passed back.  This allows the operation to be retried.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cnic_dev_list is protected by rtnl_lock and cnic_dev_lock spin_lock during
modifications.  When looping on cnic_dev_list and calling ->cnic_init(),
we should just hold rtnl_lock since ->cnic_init() may sleep.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass the TCP port parameter for iSCSI connections to the firmware in
proper endian order.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-davem' of ssh://master.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6

Commit 86bcebaf ("tcp: fix >2 iw selection") fixed a case
when congestion window initialization has been mistakenly omitted
by introducing cwnd label and putting backwards goto from the
end of the function.

This makes the code unnecessarily tricky to read and understand
on a first sight.

Shuffle the code around a little bit to make it more obvious.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfq_walk() runs without qdisc lock. By the time it selects a non empty
hash slot and sfq_dump_class_stats() is run (with lock held), slot might
have been freed : We then access q->slots[SFQ_EMPTY_SLOT], out of
bounds, and crash in slot_queue_walk()

On previous kernels, bug is here but out of bounds qs[SFQ_DEPTH] and
allot[SFQ_DEPTH] are located in struct sfq_sched_data, so no illegal
memory access happens, only possibly wrong data reported to user.

Also, slot_dequeue_tail() should make sure slot skb chain is correctly
terminated, or sfq_dump_class_stats() can access freed skbs.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If CONFIG_MAC80211_LEDS is not set, ieee80211_i.h was failing to compile,
because struct led_trigger is only declared when CONFIG_LEDS_TRIGGERS is
set.

This patch adds ifdefs around the tpt_led_trigger declaration in
ieee80211_i.h to avoid the problem.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The throughput LED trigger was always active when
the radio was enabled. In most cases that's likely
the desired behaviour, but iwlwifi requires it to
be only active when one of the virtual interfaces
is actually "connected" in some way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi and other drivers like to blink their LED
based on throughput. Implement this generically in
mac80211, based on a throughput table the driver
specifies. That way, drivers can set the blink
frequencies depending on their desired behaviour
and max throughput.

All the drivers need to do is provide an LED class
device, best with blink hardware offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The throughput trigger will require doing LED
classdev/trigger handling before register_hw(),
so drivers should have access to the trigger
names before it. If trigger registration fails,
this will still make the trigger name available,
but that's not a big problem since the default
trigger will the simply not be found.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-1000.c
	drivers/net/wireless/iwlwifi/iwl-6000.c
	drivers/net/wireless/iwlwifi/iwl-core.h

Program adapter's StationAddress register when changing device MAC address
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wrap up acceess to ASICCtrl high word with a macro
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can translate pseudo load instructions at filter check time to
dedicated instructions to speed up filtering and avoid one switch().
libpcap currently uses SKF_AD_PROTOCOL, but custom filters probably use
other ancillary accesses.

Note : I made the assertion that ancillary data was always accessed with
BPF_LD|BPF_?|BPF_ABS instructions, not with BPF_LD|BPF_?|BPF_IND ones
(offset given by K constant, not by K + X register)

On x86_64, this saves a few bytes of text :

# size net/core/filter.o.*
   text	   data	    bss	    dec	    hex	filename
   4864	      0	      0	   4864	   1300	net/core/filter.o.new
   4944	      0	      0	   4944	   1350	net/core/filter.o.old
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael pointed out that bnx2_close() already cancels bp->reset_task
and thus it is guaranteed to be idle when bnx2_remove_one() is called.
Remove the unnecessary cancel_work_sync() in remove_one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original code had a several problems:
*) It had potential null dereferences of "priv" and "res".
*) It released the memory region before it was aquired.
*) It didn't free "ndev" after it was allocated.
*) It didn't call unregister_netdev() after calling stmmac_probe().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We dereferenced params on the line before so it's too late to check if
params is NULL.  In fact, params can never be NULL and strict_cos is
either 0 or 1 so that part of the check is bogus too.  Let's remove it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Le vendredi 17 décembre 2010 à 10:26 +0100, Eric Dumazet a écrit :

>
> I think we can add this after latest Changli patch :
>
> He does one skb_clone() before calling the sniffers.
> We could set timestamp on this clone, instead of original skb.
>
> Problem solved.
>

[PATCH net-next-2.6] net: timestamp cloned packet in dev_queue_xmit_nit

Now we do one clone of skb if at least one sniffer might take packet,
we also can do the skb timestamping on the clone and let original packet
unchanged.

This is a generalization of commit 8caf1539 (net: sch_netem: Fix an
inconsistency in ingress netem timestamps.)

This way, we can have a good idea when packets are delivered to our
stack (tcpdump -i ifb0), while a tcpdump on original device gives
timestamps right before ingressing.

This also speedup our stack, avoiding taking timestamps if not needed.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Changli Gao <xiaosuo@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: Joe Perches <joe@perches.com>

Moves the PCI table to the right read-only section.
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: Joe Perches <joe@perches.com>

Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

Consolidate duplicated code into new fix_crc_bug function
and declare data in that function static const.
Signed-off-by: Joe Perches <joe@perches.com>

Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: Joe Perches <joe@perches.com>

Moves the PCI tables to the right read-only section.
Signed-off-by: Joe Perches <joe@perches.com>