Reset the XPCS upon probe stage so that we start it from well known
state.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For 10GKR rate, when link errors are found we need to return fault
status so that XPCS is correctly resumed.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When building arm32 allyesconfig:

ld.lld: error: undefined symbol: __aeabi_uldivmod
>>> referenced by spectrum_cnt.c
>>>               net/ethernet/mellanox/mlxsw/spectrum_cnt.o:(mlxsw_sp_counter_resources_register) in archive drivers/built-in.a
>>> did you mean: __aeabi_uidivmod
>>> defined in: arch/arm/lib/lib.a(lib1funcs.o)

pool_size and bank_size are u64; use div64_u64 so that 32-bit platforms
do not error.

Fixes: ab8c4cc6 ("mlxsw: spectrum_cnt: Move config validation along with resource register")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 53eca1f3 ("net: rename flow_action_hw_stats_types* ->
flow_action_hw_stats*") renamed just the flow action types and
helpers. For consistency rename variables, enums, struct members
and UAPI too (note that this UAPI was not in any official release,
yet).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

it's still possible for packetdrill to hang in mptcp_sendmsg(), when the
MPTCP socket falls back to regular TCP (e.g. after receiving unsupported
flags/version during the three-way handshake). Adjust MPTCP socket state
earlier, to ensure correct functionality of mptcp_sendmsg() even in case
of TCP fallback.

Fixes: 767d3ded ("net: mptcp: don't hang before sending 'MP capable with data'")
Fixes: 1954b860 ("mptcp: Check connection state before attempting send")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
MSCC PHY: RGMII delays and VSC8502 support

This series makes RGMII delays configurable as they should be on
Vitesse/Microsemi/Microchip RGMII PHYs, and adds support for a new RGMII
PHY.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a dual copper PHY with support for MII/GMII/RGMII on MAC side,
as well as a bunch of other features such as SyncE and Ring Resiliency.

I haven't tested interrupts and WoL, but I am confident that they work
since support is already present in the driver and the register map is
no different for this PHY.

PHY statistics work, PHY tunables appear to work, suspend/resume works.
Signed-off-by: Wes Li <wes.li@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver appears to be secretly enabling the RX clock skew
irrespective of PHY interface type, which is generally considered a big
no-no.

Make them configurable instead, and add TX internal delays when
necessary too.

While at it, configure a more canonical clock skew of 2.0 nanoseconds
than the current default of 1.1 ns.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The helper for configuring the pinout of the MII side of the PHY should
do so irrespective of whether RGMII delays are used or not. So accept
the ID, TXID and RXID variants as well, not just the no-delay RGMII
variant.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is nothing RX-specific about these clock skew values. So remove
"RX" from the name in preparation for the next patch where TX delays are
also going to be configured.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit ed0a72e0 ("net/freescale: Clean drivers from static versions")
leave behind this, remove it .
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kernel TLS forms TLS header in kernel during encryption and removes
while decryption before giving packet back to user application. The
similar logic is introduced in chtls code as well.

v1->v2:
- tls_proccess_cmsg() uses tls_handle_open_record() which is not required
  in TOE-TLS. Don't mix TOE with other TLS types.
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Problem:
TCP checksum in the output path is not being offloaded during GSO
in the following case:
The network driver does not support scatter-gather but supports
checksum offload with NETIF_F_HW_CSUM.

Cause:
skb_segment calls skb_copy_and_csum_bits if the network driver
does not announce NETIF_F_SG. It does not check if the driver
supports NETIF_F_HW_CSUM.
So for devices which might want to offload checksum but do not support SG
there is currently no way to do so if GSO is enabled.

Solution:
In skb_segment check if the network controller does checksum and if so
call skb_copy_bits instead of skb_copy_and_csum_bits.

Testing:
Without the patch, ran iperf TCP traffic with NETIF_F_HW_CSUM enabled
in the network driver. Observed the TCP checksum offload is not happening
since the skbs received by the driver in the output path have
skb->ip_summed set to CHECKSUM_NONE.

With the patch ran iperf TCP traffic and observed that TCP checksum
is being offloaded with skb->ip_summed set to CHECKSUM_PARTIAL.
Also tested with the patch by disabling NETIF_F_HW_CSUM in the driver
to cover the newly introduced if-else code path in skb_segment.

Link: https://lore.kernel.org/netdev/CA+FuTSeYGYr3Umij+Mezk9CUcaxYwqEe5sPSuXF8jPE2yMFJAw@mail.gmail.comSigned-off-by: Yadu Kishore <kyk.segfault@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: add three optimizations for mailbox handling

This patchset includes three code optimizations for mailbox handling.

[patch 1] adds a response code conversion.
[patch 2] refactors some structure definitions about PF and
VF mailbox.
[patch 3] refactors the condition whether PF responds VF's mailbox.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, PF responds to VF depending on what mailbox it is
handling, it is a bit inflexible. The correct way is, PF should
check the mbx_need_resp field to decide whether gives response
to VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For making the code more readable, this adds several new
structure to replace the msg field in structure
hclge_mbx_vf_to_pf_cmd and hclge_mbx_pf_to_vf_cmd.
Also uses macro to instead of some magic number.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when mailbox handling fails, the PF driver
just responds 1 to the VF driver. It is not sufficient
for the VF driver to find out why its mailbox fails.

So the error should be responded to VF, but the error
is type int and the response field in struct
hclge_mbx_pf_to_vf_cmd is type u16, a conversion is
needed.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

net/mptcp/options.c: In function 'mptcp_established_options_dss':
net/mptcp/options.c:338:7: warning:
 variable 'can_ack' set but not used [-Wunused-but-set-variable]

commit dc093db5 ("mptcp: drop unneeded checks")
leave behind this unused, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jian Yang says:

====================
selftests: expand txtimestamp with new features

Current txtimestamp selftest issues requests with no delay, or fixed 50
usec delay. Nsec granularity is useful to measure fine-grained latency.
A configurable delay is useful to simulate the case with cold
cachelines.

This patchset adds new flags and features to the txtimestamp selftest,
including:
- Printing in nsec (-N)
- Polling interval (-b, -S)
- Using epoll (-E, -e)
- Printing statistics
- Running individual tests in txtimestamp.sh
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Statistics on timestamps is useful to quantify average and tail latency.

Print timestamp statistics in count/avg/min/max format.
Signed-off-by: Jian Yang <jianyang@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the following new flags:
-e: use level-triggered epoll() instead of poll().
-E: use event-triggered epoll() instead of poll().
Signed-off-by: Jian Yang <jianyang@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A longer sleep duration between sendmsg()s makes more cachelines to be
evicted and results in higher latency. Making the duration configurable.

Add the following new flags:
-S: Configurable sleep duration.
-b: Busy loop instead of poll().

Remove the following flag:
-D: No delay between packets: subsumed by -S.
Signed-off-by: Jian Yang <jianyang@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Txtimestamp reports latencies in uses resolution, while nsec is needed
in cases such as measuring latencies on localhost.

Add the following new flag:
-N: print timestamps and durations in nsec (instead of usec)
Signed-off-by: Jian Yang <jianyang@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The wrapper script txtimestamp.sh executes a pre-defined list of testcases
sequentially without configuration options available.

Add an option (-r/--run) to setup the test namespace and pass remaining
arguments to txtimestamp binary. The script still runs all tests when no
argument is passed.
Signed-off-by: Jian Yang <jianyang@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Sitnicki says:

====================
net/tls: Annotate lockless access to sk_prot

We have recently noticed that there is a case of lockless read/write to
sk->sk_prot [0]. sockmap code on psock tear-down writes to sk->sk_prot,
while holding sk_callback_lock. Concurrently, tcp can access it. Usually to
read out the sk_prot pointer and invoke one of the ops,
sk->sk_prot->handler().

The lockless write (lockless in regard to concurrent reads) happens on the
following paths:

tcp_bpf_{recvmsg|sendmsg} / sock_map_unref
  sk_psock_put
    sk_psock_drop
      sk_psock_restore_proto
        WRITE_ONCE(sk->sk_prot, proto)

To prevent load/store tearing [1], and to make tooling aware of intentional
shared access [2], we need to annotate sites that access sk_prot with
READ_ONCE/WRITE_ONCE.

This series kicks off the effort to do it. Starting with net/tls.

[0] https://lore.kernel.org/bpf/a6bf279e-a998-84ab-4371-cd6c1ccbca5d@gmail.com/
[1] https://lwn.net/Articles/793253/
[2] https://github.com/google/ktsan/wiki/READ_ONCE-and-WRITE_ONCE
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

sockmap performs lockless writes to sk->sk_prot on the following paths:

tcp_bpf_{recvmsg|sendmsg} / sock_map_unref
  sk_psock_put
    sk_psock_drop
      sk_psock_restore_proto
        WRITE_ONCE(sk->sk_prot, proto)

To prevent load/store tearing [1], and to make tooling aware of intentional
shared access [2], we need to annotate other sites that access sk_prot with
READ_ONCE/WRITE_ONCE macros.

Change done with Coccinelle with following semantic patch:

@@
expression E;
identifier I;
struct sock *sk;
identifier sk_prot =~ "^sk_prot$";
@@
(
 E =
-sk->sk_prot
+READ_ONCE(sk->sk_prot)
|
-sk->sk_prot = E
+WRITE_ONCE(sk->sk_prot, E)
|
-sk->sk_prot
+READ_ONCE(sk->sk_prot)
 ->I
)
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Apart from being a "tremendous" win when it comes to generated machine
code (see bloat-o-meter output for x86-64 below) this mainly prepares
ground for annotating access to sk_prot with READ_ONCE, so that we don't
pepper the code with access annotations and needlessly repeat loads.

add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-46 (-46)
Function                                     old     new   delta
tls_init                                     851     805     -46
Total: Before=21063, After=21017, chg -0.22%
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The helper that builds kTLS proto ops doesn't need to and should not modify
the base proto ops. Annotate the parameter as read-only.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic error recovery fixes

These are a few little patches to make error recovery a little
more safe and successful.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the queue structs exist before trying to tear
them down to make for safer error recovery.

Fixes: 0f3154e6 ("ionic: Add Tx and Rx handling")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a little more cleanup when tearing down the queues.

Fixes: 1d062b7b ("ionic: Add basic adminq support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't worry if the rx filter add firmware request fails on
EEXIST, at least we know the filter is there.  Same for
the delete request, at least we know it isn't there.

Fixes: 2a654540 ("ionic: Add Rx filter and rx_mode ndo support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't save the lif->dentry until we know we have
a good value.

Fixes: 1a58e196 ("ionic: Add basic lif support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible (but unlikely) that FW was busy and missed a heartbeat
check but is still alive and will process the pending request, so don't
clean the dev_cmd in this case.  This occasionally occurs when working
with a card that is supporting many devices and is trying to shut them
all down at once, but still wants to see that last LIF disable request.

Fixes: 97ca4865 ("ionic: add heartbeat check")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Short circuit the cleanup if we get a timeout error from
ionic_qcq_disable() so as to not have to wait too long
on shutdown when we already know the FW is not responding.

Fixes: 0f3154e6 ("ionic: Add Tx and Rx handling")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't assume the receive buffer size is a power-of-2 number of pages.
Instead, define the receive buffer size independently, and then
compute the page order from that size when needed.

This fixes a build problem that arises when the ARM64_PAGE_SHIFT
config option is set to have a page size greater than 4KB.  The
problem was identified by Linux Kernel Functional Testing.

The IPA code basically assumed the page size to be 4KB.  A larger page
size caused the receive buffer size to become correspondingly larger
(32KB or 128KB for ARM64_16K_PAGES and ARM64_64K_PAGES, respectively).
The receive buffer size is used to compute an "aggregation byte limit"
value that gets programmed into the hardware, and the large page sizes
caused that limit value to be too big to fit in a 5 bit field.  This
triggered a BUILD_BUG_ON() call in ipa_endpoint_validate_build().

This fix causes a lot of receive buffer memory to be wasted if
system is configured for page size greater than 4KB.  But such a
misguided configuration will now build successfully.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-net-next-2020-03-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Another set of changes:
 * HE ranging (fine timing measurement) API support
 * hwsim gets virtio support, for use with wmediumd,
   to be able to simulate with multiple machines
 * eapol-over-nl80211 improvements to exclude preauth
 * IBSS reset support, to recover connections from
   userspace
 * and various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

SJA1105 switches R and S have one SerDes port with an 802.3z
quasi-compatible PCS, hardwired on port 4. The other ports are still
MII/RMII/RGMII. The PCS performs rate adaptation to lower link speeds;
the MAC on this port is hardwired at gigabit. Only full duplex is
supported.

The SGMII port can be configured as part of the static config tables, as
well as through a dedicated SPI address region for its pseudo-clause-22
registers. However it looks like the static configuration is not
able to change some out-of-reset values (like the value of MII_BMCR), so
at the end of the day, having code for it is utterly pointless. We are
just going to use the pseudo-C22 interface.

Because the PCS gets reset when the switch resets, we have to add even
more restoration logic to sja1105_static_config_reload, otherwise the
SGMII port breaks after operations such as enabling PTP timestamping
which require a switch reset.

>From PHYLINK perspective, the switch supports *only* SGMII (it doesn't
support 1000Base-X). It also doesn't expose access to the raw config
word for in-band AN in registers MII_ADV/MII_LPA.
It is able to work in the following modes:
 - Forced speed
 - SGMII in-band AN slave (speed received from PHY)
 - SGMII in-band AN master (acting as a PHY)

The latter mode is not supported by this patch. It is even unclear to me
how that would be described. There is some code for it left in the
patch, but 'an_master' is always passed as false.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
net: bridge: vlan options: nest the tunnel options

After a discussion with Roopa about the new tunnel vlan option, she
suggested that we'll be adding more tunnel options and attributes, so
it'd be better to have them all grouped together under one main vlan
entry tunnel attribute instead of making them all main attributes. Since
the tunnel code was added in this net-next cycle and still hasn't been
released we can easily nest the BRIDGE_VLANDB_ENTRY_TUNNEL_ID attribute
in BRIDGE_VLANDB_ENTRY_TUNNEL_INFO and allow for any new tunnel
attributes to be added there. In addition one positive side-effect is
that we can remove the outside vlan info flag which controlled the
operation (setlink/dellink) and move it under a new nested attribute so
user-space can specify it explicitly.

Thus the vlan tunnel format becomes:
 [BRIDGE_VLANDB_ENTRY]
     [BRIDGE_VLANDB_ENTRY_TUNNEL_INFO]
         [BRIDGE_VLANDB_TINFO_ID]
         [BRIDGE_VLANDB_TINFO_CMD]
         ...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have a nested tunnel info attribute we can add a separate
one for the tunnel command and require it explicitly from user-space. It
must be one of RTM_SETLINK/DELLINK. Only RTM_SETLINK requires a valid
tunnel id, DELLINK just removes it if it was set before. This allows us
to have all tunnel attributes and control in one place, thus removing
the need for an outside vlan info flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>