Pull clk fixes from Stephen Boyd:
 "One small build fix, a couple do_div() fixes, and a fix for the gpio
  basic clock type are the major changes here.  There's also a couple
  fixes for the TI, sunxi, and scpi clock drivers"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: sunxi: pll2: Fix clock running too fast
  clk: scpi: add missing of_node_put
  clk: qoriq: fix memory leak
  imx/clk-pllv2: fix wrong do_div() usage
  imx/clk-pllv1: fix wrong do_div() usage
  clk: mmp: add linux/clk.h includes
  clk: ti: drop locking code from mux/divider drivers
  clk: ti816x: Add missing dmtimer clkdev entries
  clk: ti: fapll: fix wrong do_div() usage
  clk: ti: clkt_dpll: fix wrong do_div() usage
  clk: gpio: Get parent clk names in of_gpio_clk_setup()

Pull IPMI fix from Corey Minyard:
 "Fix an Oops if an interrupt occurs at startup.  This can happen on
  some hardware"

* tag 'for-linus-4.4-1' of git://git.code.sf.net/p/openipmi/linux-ipmi:
  ipmi: move timer init to before irq is setup

We encountered a panic on boot in ipmi_si on a dell per320 due to an
uninitialized timer as follows.

static int smi_start_processing(void       *send_info,
                                ipmi_smi_t intf)
{
        /* Try to claim any interrupts. */
        if (new_smi->irq_setup)
                new_smi->irq_setup(new_smi);

 --> IRQ arrives here and irq handler tries to modify uninitialized timer

    which triggers BUG_ON(!timer->function) in __mod_timer().

 Call Trace:
   <IRQ>
   [<ffffffffa0532617>] start_new_msg+0x47/0x80 [ipmi_si]
   [<ffffffffa053269e>] start_check_enables+0x4e/0x60 [ipmi_si]
   [<ffffffffa0532bd8>] smi_event_handler+0x1e8/0x640 [ipmi_si]
   [<ffffffff810f5584>] ? __rcu_process_callbacks+0x54/0x350
   [<ffffffffa053327c>] si_irq_handler+0x3c/0x60 [ipmi_si]
   [<ffffffff810efaf0>] handle_IRQ_event+0x60/0x170
   [<ffffffff810f245e>] handle_edge_irq+0xde/0x180
   [<ffffffff8100fc59>] handle_irq+0x49/0xa0
   [<ffffffff8154643c>] do_IRQ+0x6c/0xf0
   [<ffffffff8100ba53>] ret_from_intr+0x0/0x11

        /* Set up the timer that drives the interface. */
        setup_timer(&new_smi->si_timer, smi_timeout, (long)new_smi);

The following patch fixes the problem.

To: Openipmi-developer@lists.sourceforge.net
To: Corey Minyard <minyard@acm.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # Applies cleanly to 3.10-, needs small rework before

ROL on a 32 bit integer with a shift of 32 or more is undefined and the
result is arch-dependent. Avoid this by handling the trivial case of
roling by 0 correctly.

The trivial solution of checking if shift is 0 breaks gcc's detection
of this code as a ROL instruction, which is unacceptable.

This bug was reported and fixed in GCC
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=57157):

	The standard rotate idiom,

	  (x << n) | (x >> (32 - n))

	is recognized by gcc (for concreteness, I discuss only the case that x
	is an uint32_t here).

	However, this is portable C only for n in the range 0 < n < 32. For n
	== 0, we get x >> 32 which gives undefined behaviour according to the
	C standard (6.5.7, Bitwise shift operators). To portably support n ==
	0, one has to write the rotate as something like

	  (x << n) | (x >> ((-n) & 31))

	And this is apparently not recognized by gcc.

Note that this is broken on older GCCs and will result in slower ROL.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull vfs fixes from Al Viro:
 "A couple of fixes, both -stable fodder (9p one all way back to 2.6.32,
  dio - to all branches where "Fix negative return from dio read beyond
  eof" will end up it; it's a fixup to commit marked for -stable)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fix the regression from "direct-io: Fix negative return from dio read beyond eof"
  9p: ->evict_inode() should kick out ->i_data, not ->i_mapping

Pull PCI fixes from Bjorn Helgaas:
 "These are more fixes I'd like to have in v4.4.  Several for the Altera
  driver added for v4.4, and one for an MSI domain problem that affects
  several arm64 platforms:

  MSI:
   - Only use the generic MSI layer when domain is hierarchical (Marc
     Zyngier)

  Altera host bridge driver:
   - Fix loop in tlp_read_packet() (Dan Carpenter)
   - Fix Requester ID for config accesses (Ley Foon Tan)
   - Check TLP completion status (Ley Foon Tan)
   - Fix error when INTx is 4 (Ley Foon Tan)"

* tag 'pci-v4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: altera: Fix error when INTx is 4
  PCI: altera: Check TLP completion status
  PCI: altera: Fix Requester ID for config accesses
  PCI: altera: Fix loop in tlp_read_packet()
  PCI/MSI: Only use the generic MSI layer when domain is hierarchical

Pull uml fixes from Richard Weinberger:
 "This contains various bug fixes, most of them are fall out from the
  merge window"

* 'for-linus-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: fix returns without va_end
  um: Fix fpstate handling
  arch: um: fix error when linking vmlinux.
  um: Fix get_signal() usage

Pull cgroup fixes from Tejun Heo:
 "More change than I'd have liked at this stage.  The pids controller
  and the changes made to cgroup core to support it introduced and
  revealed several important issues.

   - Assigning membership to a newly created task and migrating it can
     race leading to incorrect accounting.  Oleg fixed it by widening
     threadgroup synchronization.  It looks like we'll be able to merge
     it with a different percpu rwsem which is used in fork path making
     things simpler and cheaper.

   - The recent change to extend cgroup membership to zombies (so that
     pid accounting can extend till the pid is actually released) missed
     pinning the underlying data structures leading to use-after-free.
     Fixed.

   - v2 hierarchy was calling subsystem callbacks with the wrong target
     cgroup_subsys_state based on the incorrect assumption that they
     share the same target.  pids is the first controller affected by
     this.  Subsys callbacks updated so that they can deal with
     multi-target migrations"

* 'for-4.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup_pids: don't account for the root cgroup
  cgroup: fix handling of multi-destination migration from subtree_control enabling
  cgroup_freezer: simplify propagation of CGROUP_FROZEN clearing in freezer_attach()
  cgroup: pids: kill pids_fork(), simplify pids_can_fork() and pids_cancel_fork()
  cgroup: pids: fix race between cgroup_post_fork() and cgroup_migrate()
  cgroup: make css_set pin its css's to avoid use-afer-free
  cgroup: fix cftype->file_offset handling

Pull libata fixes from Tejun Heo:
 "Nothing too interesting.  All are device specific additions and
  workarounds"

* 'for-4.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ata/sata_fsl.c: add ATA_FLAG_NO_LOG_PAGE to blacklist the controller for log page reads
  libata-eh.c: Introduce new ata port flag for controller which lockup on read log page
  sata_sil: disable trim
  AHCI: Fix softreset failed issue of Port Multiplier
  sata/mvebu: use #ifdef around suspend/resume code
  ahci: Order SATA device IDs for codename Lewisburg
  ahci: Add Device ID for Intel Sunrise Point PCH

When using va_list ensure that va_start will be followed by va_end.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

The x86 FPU cleanup changed fpstate to a plain integer.
UML on x86 has to deal with that too.
Signed-off-by: Richard Weinberger <richard@nod.at>

On gcc Ubuntu 4.8.4-2ubuntu1~14.04, linking vmlinux fails with:

arch/um/os-Linux/built-in.o: In function `os_timer_create':
/android/kernel/android/arch/um/os-Linux/time.c:51: undefined reference to `timer_create'
arch/um/os-Linux/built-in.o: In function `os_timer_set_interval':
/android/kernel/android/arch/um/os-Linux/time.c:84: undefined reference to `timer_settime'
arch/um/os-Linux/built-in.o: In function `os_timer_remain':
/android/kernel/android/arch/um/os-Linux/time.c:109: undefined reference to `timer_gettime'
arch/um/os-Linux/built-in.o: In function `os_timer_one_shot':
/android/kernel/android/arch/um/os-Linux/time.c:132: undefined reference to `timer_settime'
arch/um/os-Linux/built-in.o: In function `os_timer_disable':
/android/kernel/android/arch/um/os-Linux/time.c:145: undefined reference to `timer_settime'

This is because -lrt appears in the generated link commandline
after arch/um/os-Linux/built-in.o. Fix this by removing -lrt from
arch/um/Makefile and adding it to the UM-specific section of
scripts/link-vmlinux.sh.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

If get_signal() returns us a signal to post
we must not call it again, otherwise the already
posted signal will be overridden.
Before commit a610d6e6 this was the case as we stopped
the while after a successful handle_signal().

Cc: <stable@vger.kernel.org> # 3.10-
Fixes: a610d6e6 ("pull clearing RESTORE_SIGMASK into block_sigmask()")
Signed-off-by: Richard Weinberger <richard@nod.at>

Pull perf fixes from Ingo Molnar:
 "This tree includes four core perf fixes for misc bugs, three fixes to
  x86 PMU drivers, and two updates to old email addresses"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Do not send exit event twice
  perf/x86/intel: Fix INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_NA macro
  perf/x86/intel: Make L1D_PEND_MISS.FB_FULL not constrained on Haswell
  perf: Fix PERF_EVENT_IOC_PERIOD deadlock
  treewide: Remove old email address
  perf/x86: Fix LBR call stack save/restore
  perf: Update email address in MAINTAINERS
  perf/core: Robustify the perf_cgroup_from_task() RCU checks
  perf/core: Fix RCU problem with cgroup context switching code

Sure, it's better to bail out of past-the-eof read and return 0 than return
a bogus negative value on such.  Only we'd better make sure we are bailing out
with 0 and not -ENOMEM...

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

For block devices the pagecache is associated with the inode
on bdevfs, not with the aliasing ones on the mountable filesystems.
The latter have its own ->i_data empty and ->i_mapping pointing
to the (unique per major/minor) bdevfs inode.  That guarantees
cache coherence between all block device inodes with the same
device number.

Eviction of an alias inode has no business trying to evict the
pages belonging to bdevfs one; moreover, ->i_mapping is only
safe to access when the thing is opened.  At the time of
->evict_inode() the victim is definitely *not* opened.  We are
about to kill the address space embedded into struct inode
(inode->i_data) and that's what we need to empty of any pages.

9p instance tries to empty inode->i_mapping instead, which is
both unsafe and bogus - if we have several device nodes with
the same device number in different places, closing one of them
should not try to empty the (shared) page cache.

Fortunately, other instances in the tree are OK; they are
evicting from &inode->i_data instead, as 9p one should.

Cc: stable@vger.kernel.org # v2.6.32+, ones prior to 2.6.36 need only half of that
Reported-by: "Suzuki K. Poulose" <Suzuki.Poulose@arm.com>
Tested-by: "Suzuki K. Poulose" <Suzuki.Poulose@arm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull virtio fixes from Michael Tsirkin:
 "This includes some fixes and cleanups in virtio and vhost code.

  Most notably, shadowing the index fixes the excessive cacheline
  bouncing observed on AMD platforms"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_ring: shadow available ring flags & index
  virtio: Do not drop __GFP_HIGH in alloc_indirect
  vhost: replace % with & on data path
  tools/virtio: fix byteswap logic
  tools/virtio: move list macro stubs
  virtio: fix memory leak of virtio ida cache layers
  vhost: relax log address alignment
  virtio-net: Stop doing DMA from the stack

Pull ext4 fixes from Ted Ts'o:
 "Ext4 bug fixes for v4.4, including fixes for post-2038 time encodings,
  some endian conversion problems with ext4 encryption, potential memory
  leaks after truncate in data=journal mode, and an ocfs2 regression
  caused by a jbd2 performance improvement"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  jbd2: fix null committed data return in undo_access
  ext4: add "static" to ext4_seq_##name##_fops struct
  ext4: fix an endianness bug in ext4_encrypted_follow_link()
  ext4: fix an endianness bug in ext4_encrypted_zeroout()
  jbd2: Fix unreclaimed pages after truncate in data=journal mode
  ext4: Fix handling of extended tv_sec

Improves cacheline transfer flow of available ring header.

Virtqueues are implemented as a pair of rings, one producer->consumer
avail ring and one consumer->producer used ring; preceding the
avail ring in memory are two contiguous u16 fields -- avail->flags
and avail->idx. A producer posts work by writing to avail->idx and
a consumer reads avail->idx.

The flags and idx fields only need to be written by a producer CPU
and only read by a consumer CPU; when the producer and consumer are
running on different CPUs and the virtio_ring code is structured to
only have source writes/sink reads, we can continuously transfer the
avail header cacheline between 'M' states between cores. This flow
optimizes core -> core bandwidth on certain CPUs.

(see: "Software Optimization Guide for AMD Family 15h Processors",
Section 11.6; similar language appears in the 10h guide and should
apply to CPUs w/ exclusive caches, using LLC as a transfer cache)

Unfortunately the existing virtio_ring code issued reads to the
avail->idx and read-modify-writes to avail->flags on the producer.

This change shadows the flags and index fields in producer memory;
the vring code now reads from the shadows and only ever writes to
avail->flags and avail->idx, allowing the cacheline to transfer
core -> core optimally.

In a concurrent version of vring_bench, the time required for
10,000,000 buffer checkout/returns was reduced by ~2% (average
across many runs) on an AMD Piledriver (15h) CPU:

(w/o shadowing):
 Performance counter stats for './vring_bench':
     5,451,082,016      L1-dcache-loads
     ...
       2.221477739 seconds time elapsed

(w/ shadowing):
 Performance counter stats for './vring_bench':
     5,405,701,361      L1-dcache-loads
     ...
       2.168405376 seconds time elapsed

The further away (in a NUMA sense) virtio producers and consumers are
from each other, the more we expect to benefit. Physical implementations
of virtio devices and implementations of virtio where the consumer polls
vring avail indexes (vhost) should also benefit.
Signed-off-by: Venkatesh Srinivas <venkateshs@google.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

b92b1b89 ("virtio: force vring descriptors to be allocated from
lowmem") tried to exclude highmem pages for descriptors so it cleared
__GFP_HIGHMEM from a given gfp mask. The patch also cleared __GFP_HIGH
which doesn't make much sense for this fix because __GFP_HIGH only
controls access to memory reserves and it doesn't have any influence
on the zone selection. Some of the call paths use GFP_ATOMIC and
dropping __GFP_HIGH will reduce their changes for success because the
lack of access to memory reserves.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mel Gorman <mgorman@techsingularity.net>

We know vring num is a power of 2, so use &
to mask the high bits.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

commit cf561f0d ("virtio: introduce
virtio_is_little_endian() helper") changed byteswap logic to
skip feature bit checks for LE platforms, but didn't
update tools/virtio, so vring_bench started failing.

Update the copy under tools/virtio/ (TODO: find a way to avoid this code
duplication).

Cc: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

Makes them more generally available.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

The virtio core uses a static ida named virtio_index_ida for
assigning index numbers to virtio devices during registration.
The ida core may allocate some internal idr cache layers and
an ida bitmap upon any ida allocation, and all these layers are
truely freed only upon the ida destruction. The virtio_index_ida
is not destroyed at present, leading to a memory leak when using
the virtio core as a module and atleast one virtio device is
registered and unregistered.

Fix this by invoking ida_destroy() in the virtio core module
exit.

Cc: stable@vger.kernel.org
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

commit 5d9a07b0 ("vhost: relax used
address alignment") fixed the alignment for the used virtual address,
but not for the physical address used for logging.

That's a mistake: alignment should clearly be the same for virtual and
physical addresses,

Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

Every attempt to issue a read log page command lockup the controller.
The command is currently sent if the sata device includes the devlsp feature
to read out the timing data.
This attempt to read the data, locks up the controller and the device
is not recognzied correctly (failed to set xfermode) and cannot be accessed.

This was found on Freescale P1013/P1022 and T4240 CPUs
using a ATP IG mSATA 4GB with the devslp feature.

fsl-sata ff718000.sata: Sata FSL Platform/CSB Driver init
[    1.254195] scsi0 : sata_fsl
[    1.256004] ata1: SATA max UDMA/133 irq 74
[    1.370666] fsl-gianfar ethernet.3: enabled errata workarounds, flags: 0x4
[    1.470671] fsl-gianfar ethernet.4: enabled errata workarounds, flags: 0x4
[    1.775584] ata1: Signature Update detected @ 504 msecs
[    1.947594] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.948366] ata1.00: ATA-8: ATP IG mSATA, 20150311, max UDMA/133
[    1.948371] ata1.00: 7732368 sectors, multi 0: LBA
[    1.948843] ata1.00: failed to get Identify Device Data, Emask 0x1
[    1.948857] ata1.00: failed to set xfermode (err_mask=0x40)
[    7.467557] ata1: Signature Update detected @ 504 msecs
[    7.639560] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    7.651320] ata1.00: failed to get Identify Device Data, Emask 0x1
[    7.651360] ata1.00: failed to set xfermode (err_mask=0x40)
[    7.655628] ata1: limiting SATA link speed to 1.5 Gbps
[    7.659458] ata1.00: limiting speed to UDMA/133:PIO3
[   13.163554] ata1: Signature Update detected @ 504 msecs
[   13.335558] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   13.347298] ata1.00: failed to get Identify Device Data, Emask 0x1
[   13.347334] ata1.00: failed to set xfermode (err_mask=0x40)
[   13.351601] ata1.00: disabled
[   13.353278] ata1: exception Emask 0x50 SAct 0x0 SErr 0x800 action 0x6 frozen t4
[   13.359281] ata1: SError: { HostInt }
[   13.361644] ata1: hard resetting link
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Tejun Heo <tj@kernel.org>

Some controller lockup on a ata_read_log_page.
Add new ata port flag ATA_FLAG_NO_LOG_PAGE which can used
to blacklist a controller.

If this flag is set, any attempt to read a log page returns an error
without actually issuing the command.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Tejun Heo <tj@kernel.org>

The following commit which went into mainline through networking tree

  3b13758f ("cgroups: Allow dynamically changing net_classid")

conflicts in net/core/netclassid_cgroup.c with the following pending
fix in cgroup/for-4.4-fixes.

  1f7dd3e5 ("cgroup: fix handling of multi-destination migration from subtree_control enabling")

The former separates out update_classid() from cgrp_attach() and
updates it to walk all fds of all tasks in the target css so that it
can be used from both migration and config change paths.  The latter
drops @css from cgrp_attach().

Resolve the conflict by making cgrp_attach() call update_classid()
with the css from the first task.  We can revive @tset walking in
cgrp_attach() but given that net_cls is v1 only where there always is
only one target css during migration, this is fine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Nina Schiff <ninasc@fb.com>

Once virtio starts using the DMA API, we won't be able to safely DMA
from the stack.  virtio-net does a couple of config DMA requests
from small stack buffers -- switch to using dynamically-allocated
memory.

This should have no effect on any performance-critical code paths.
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org>

The ioctl IOC_LIBCFS_PING_TEST has not been used in ages.  The recent
nidstring changes which moved all the nidstring operations from libcfs
to the LNet layer but this ioctl code was still using an nidstring
operation that was causing a circular dependency loop between libcfs and
LNet.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull vfs fixes from Al Viro:
 "A couple of fixes (-stable fodder) + dead code removal after the
  overlayfs fix.

  I agree that it's better to separate from the fix part to make
  backporting easier, but IMO it's not worth delaying said dead code
  removal until the next window"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  Don't reset ->total_link_count on nested calls of vfs_path_lookup()
  ovl: get rid of the dead code left from broken (and disabled) optimizations
  ovl: fix permission checking for setattr

we already zero it on outermost set_nameidata(), so initialization in
path_init() is pointless and wrong.  The same DoS exists on pre-4.2
kernels, but there a slightly different fix will be needed.

Cc: stable@vger.kernel.org # v4.2
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

[Al Viro] The bug is in being too enthusiastic about optimizing ->setattr()
away - instead of "copy verbatim with metadata" + "chmod/chown/utimes"
(with the former being always safe and the latter failing in case of
insufficient permissions) it tries to combine these two.  Note that copyup
itself will have to do ->setattr() anyway; _that_ is where the elevated
capabilities are right.  Having these two ->setattr() (one to set verbatim
copy of metadata, another to do what overlayfs ->setattr() had been asked
to do in the first place) combined is where it breaks.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull scheduler fixes from Thomas Gleixner:
 "This updates contains the following changes:

   - Fix a signal handling regression in the bit wait functions.

   - Avoid false positive warnings in the wakeup path.

   - Initialize the scheduler root domain properly.

   - Handle gtime calculations in proc/$PID/stat proper.

   - Add more documentation for the barriers in try_to_wake_up().

   - Fix a subtle race in try_to_wake_up() which might cause a task to
     be scheduled on two cpus

   - Compile static helper function only when it is used"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Fix an SMP ordering race in try_to_wake_up() vs. schedule()
  sched/core: Better document the try_to_wake_up() barriers
  sched/cputime: Fix invalid gtime in proc
  sched/core: Clear the root_domain cpumasks in init_rootdomain()
  sched/core: Remove false-positive warning from wake_up_process()
  sched/wait: Fix signal handling in bit wait helpers
  sched/rt: Hide the push_irq_work_func() declaration

Pull x86 fixes from Thoma Gleixner:
 "Another round of fixes for x86:

   - Move the initialization of the microcode driver to late_initcall to
     make sure everything that init function needs is available.

   - Make sure that lockdep knows about interrupts being off in the
     entry code before calling into c-code.

   - Undo the cpu hotplug init delay regression.

   - Use the proper conditionals in the mpx instruction decoder.

   - Fixup restart_syscall for x32 tasks.

   - Fix the hugepage regression on PAE kernels which was introduced
     with the latest PAT changes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/signal: Fix restart_syscall number for x32 tasks
  x86/mpx: Fix instruction decoder condition
  x86/mm: Fix regression with huge pages on PAE
  x86 smpboot: Re-enable init_udelay=0 by default on modern CPUs
  x86/entry/64: Fix irqflag tracing wrt context tracking
  x86/microcode: Initialize the driver late when facilities are up

Pull SCSI fixes from James Bottomley:
 "This is quite a bumper crop of fixes: three from Arnd correcting
  various build issues in some configurations, a lock recursion in
  qla2xxx.  Two potentially exploitable issues in hpsa and mvsas, a
  potential null deref in st, a revert of a bdi registration fix that
  turned out to cause even more problems, a set of fixes to allow people
  who only defined MPT2SAS to still work after the mpt2/mpt3sas merger
  and a couple of fixes for issues turned up by the hyper-v storvsc
  driver"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  mpt3sas: fix Kconfig dependency problem for mpt2sas back compatibility
  Revert "scsi: Fix a bdi reregistration race"
  mpt3sas: Add dummy Kconfig option for backwards compatibility
  Fix a memory leak in scsi_host_dev_release()
  block/sd: Fix device-imposed transfer length limits
  scsi_debug: fix prevent_allow+verify regressions
  MAINTAINERS: Add myself as co-maintainer of the SCSI subsystem.
  sd: Make discard granularity match logical block size when LBPRZ=1
  scsi: hpsa: select CONFIG_SCSI_SAS_ATTR
  scsi: advansys needs ISA dma api for ISA support
  scsi_sysfs: protect against double execution of __scsi_remove_device()
  st: fix potential null pointer dereference.
  scsi: report 'INQUIRY result too short' once per host
  advansys: fix big-endian builds
  qla2xxx: Fix rwlock recursion
  hpsa: logical vs bitwise AND typo
  mvsas: don't allow negative timeouts
  mpt3sas: Fix use sas_is_tlr_enabled API before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag

In case we monitor events system wide, we get EXIT event
(when configured) twice for each task that exited.

Note doubled lines with same pid/tid in following example:

  $ sudo ./perf record -a
  ^C[ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 0.480 MB perf.data (2518 samples) ]
  $ sudo ./perf report -D | grep EXIT

  0 60290687567581 0x59910 [0x38]: PERF_RECORD_EXIT(1250:1250):(1250:1250)
  0 60290687568354 0x59948 [0x38]: PERF_RECORD_EXIT(1250:1250):(1250:1250)
  0 60290687988744 0x59ad8 [0x38]: PERF_RECORD_EXIT(1250:1250):(1250:1250)
  0 60290687989198 0x59b10 [0x38]: PERF_RECORD_EXIT(1250:1250):(1250:1250)
  1 60290692567895 0x62af0 [0x38]: PERF_RECORD_EXIT(1253:1253):(1253:1253)
  1 60290692568322 0x62b28 [0x38]: PERF_RECORD_EXIT(1253:1253):(1253:1253)
  2 60290692739276 0x69a18 [0x38]: PERF_RECORD_EXIT(1252:1252):(1252:1252)
  2 60290692739910 0x69a50 [0x38]: PERF_RECORD_EXIT(1252:1252):(1252:1252)

The reason is that the cpu contexts are processes each time
we call perf_event_task. I'm changing the perf_event_aux logic
to serve task_ctx and cpu contexts separately, which ensure we
don't get EXIT event generated twice on same cpu context.

This does not affect other auxiliary events, as they don't
use task_ctx at all.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1446649205-5822-1-git-send-email-jolsa@kernel.orgSigned-off-by: Ingo Molnar <mingo@kernel.org>

We need to add rest of the flags to the constraint mask
instead of another INTEL_ARCH_EVENT_MASK, fixing a typo.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1447061071-28085-1-git-send-email-jolsa@kernel.orgSigned-off-by: Ingo Molnar <mingo@kernel.org>