Signed-off-by: David S. Miller <davem@davemloft.net>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IPV6] fix ipv6_getsockopt_sticky copy_to_user leak
  [IPV6]: Fix for ipv6_setsockopt NULL dereference
  [DCCP]: Initialise write_xmit_timer also on passive sockets
  [IPV4]: Fix rtm_to_ifaddr() error handling.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] refresh config files
  [IA64] put kdump_find_rsvd_region in __init
  [IA64] Remove sparse warning from unwind code
  [IA64] add missing syscall trace clear
  [IA64] Cleanup in crash.c
  [IA64] kexec: declare ia64_mca_pal_base in mca.h rather than kexec.h
  [IA64] pci_get_legacy_ide_irq should return irq (not GSI)
  [IA64] whitespace fixes for include/asm-ia64/sal.h
  [IA64] Cache error recovery
  [IA64] Proper handling of TLB errors from duplicate itr.d dropins

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
  kobject: new_device->kref wasn't putted after error in kobject_move()
  driver core: export device_rename
  Remove devfs from MAINTAINERS
  Driver core: add device symlink back to sysfs
  Revert "driver core: refcounting fix"

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
  pci: fix section mismatch warning
  PCI: aer: fix section mismatch warning
  pcie: fix section mismatch warning
  PCI: allow multiple calls to pcim_pin_device()

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (23 commits)
  USB Elan FTDI: check for workqueue creation
  USB: fix spinlock recursion in cdc-acm.c
  USB: fix Unaligned access in EHCI driver
  USB: Product ID for FT232RL in ftdi_sio
  USBNET: DM9501: Add Corega FEther USB-TXC support.
  USB: ipaq.c: Additional devices
  USB: further fix for usb-serial
  USB: fix usb-serial device naming bug
  USB: RTS/DTR signal patch for airprime driver
  USB: ftdi_sio: use port_probe / port_remove thereby fixing access to the latency_timer
  usb-serial: fix shutdown / device_unregister order
  USB: add Additional PIDs in ftdi_sio
  USB: add QL355P power supply ids to fdti_sio
  USB: New device IDs for cp2101 driver
  USB: kill dead code from hub.c
  USB: ratelimit debounce error messages
  USB: pxa2xx_udc: fix hardcoded irq number
  UHCI: fix port resume problem
  USB: set the correct interval for interrupt URBs
  USB: goku_udc: Remove crude cache coherency code
  ...

Delay the read of the EC status register until
after the event that caused it occurs -- otherwise
it is possible to read and act on stale status that was
associated with the previous event.

Do this with a perpetually incrementing "event_count" to detect
when a new event occurs and it is safe to read status.

There is no workaround for polling mode -- it is inherently
exposed to reading and acting on stale status, since it
doesn't have an interrupt to tell it the event completed.

http://bugzilla.kernel.org/show_bug.cgi?id=8110Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Avoid NULL pointer usage if workqueue creation failed.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this fixes the spinlock recursion issue. The older fix was incomplete.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I get following warnings on spar64:
Kernel unaligned access at TPC[1000c9e4] ehci_hub_control+0x54c/0x68c [ehci_hcd]

Despite of the comment in the patched code, the type cast used there
does make unaligned access. The fix was made as it's done in
ohci-hub.c.
Signed-off-by: Max Dmitrichenko <dmitrmax@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Here is a patch adding the PID for the FT232RL to ftdi_sio. The patch
generates a warning during compilation because get_ftdi_divisor doesn't
explicitly handle the FT232RL with this patch, so I guess you don't want
to use it in its current state. It is all I could come up with with the
knowledge I have of the drivers at the moment, though, and I hope you
can have some use for it at least. It works fine with my DLP-TILT with
an FT232RL.

From: Gard Spreemann <spreeman@stud.ntnu.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Additional devices
Signed-off-by: Andre Spahlinger <uenz@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this is a fix for the outstanding usb-serial issues.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Am Montag, 26. Februar 2007 15:16 schrieb Craig Schlenter:
> Hi Greg
> 
> 34ef50e5 is definitely
> the source of the problem. Reverting that makes the
> ftdi port show up as ttyUSB0 again for me and it
> can actually be opened.

This patch should fix the issue.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Craig Schlenter <craig@codefountain.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I encountered some problems with the airprime driver in use with a Novatel
Merlin XU870:

Closing an open Connection to e.g. /dev/ttyUSB0 doesn't reset the
RTS/DTR lines of the Modem.  Consequently, when I use minicom to
establish a connection by "ATD*99#" the modem doesn't hang up even if i
exit minicom and so I cannot reuse the modem unless I remove it and plug
it in again.

With the attached patch, the RTS/DTR lines are resetted on a close.  The
code was mainly taken from the option.c driver.

Convert all the port specific code in attach / shutdown to use the new
port_probe / port_register callbacks from device_register /
device_unregister allowing adding the sysfs attributes to be added at
the correct time and to the serial port device itself, instead of to
the unadorned usb device, avoiding a NULL dereference.
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Ensure that the ->port_remove() callbacks get called before the
->shutdown() callback which makeing the order symmetric with
->attach() being called before ->port_probe().
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I've developed some devices with FTDI chips (FT232xx). FTDI was so kind
to give some own PID's which I can use together with their VID. Some of
the devices are already very popular here and I have customers from
universities, institutes .....

I use the FTDI VID 0x0403. My PID's are:

0xff38 - IBS US485 (USB<-->RS422/485 interface)
0xff39 - IBS PIC-Programmer
0xff3a - IBS Card reader for PCMCIA SRAM-cards
0xff3b - IBS PK1 - Particel counter
0xff3c - IBS RS232 - Monitor
0xff3d - APP 70 (dust monitoring system)
0xff3e - IBS PEDO-Modem (RF modem 868.35 MHz)
0xff3f - future device

The company is "IBS Ing.-Buero Schleusener".


From: Thomas Schleusener <thomas@be-schl.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Here are two new device IDs for the cp2101 driver.
The diff is with linus's tree as of this evending.

From: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this kills residual obsoletet code from hub.c
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

flaky hardware can cause a lot of debounce failed messages. To limit
the performance impact, a ratelimit should be used.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch changes last use of hardcoded number of irq to
use platfrom_get_irq.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as863) fixes a problem encountered sometimes when resuming
a port on a UHCI controller.  The hardware may turn off the
Resume-Detect bit before turning off the Suspend bit, leading usbcore
to think that the port is still suspended and the resume has failed.
The patch makes uhci_finish_suspend() wait until both bits are safely
off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as862) fixes a couple of bugs in the way usbcore handles
intervals for interrupt URBs.  usb_interrupt_msg (and usb_bulk_msg for
backward compatibility) don't set the interval correctly for
high-speed devices.  proc_do_submiturb() doesn't set it correctly when
a bulk URB is submitted to an interrupt endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This is deep architecture specific magic and does should not to exist
in a driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds an usual_devs entry for the Nokia 6288. Originally from
Andrew with a re-diff by Phil.

From: Andrew Nayenko <relan@bk.ru>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch removes the duplicate supertop entries that made it into the
.21 rc kernels.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Rename the driver struct used with at91_udc to prevent yet another
bogus warning from "modpost".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>