[ Upstream commit 94c43b98 ]

Some buggy USB disk adapters disconnect and reconnect multiple times
during the enumeration procedure.  This may lead to a device
connecting at full speed instead of high speed, because when the USB
stack sees that a device isn't able to enumerate at high speed, it
tries to hand the connection over to a full-speed companion
controller.

The logic for doing this is careful to check that the device is still
connected.  But this check is inadequate if the device disconnects and
reconnects before the check is done.  The symptom is that a device
works, but much more slowly than it is capable of operating.

The situation was made worse recently by commit 22547c4c ("usb:
hub: Wait for connection to be reestablished after port reset"), which
increases the delay following a reset before a disconnect is
recognized, thus giving the device more time to reconnect.

This patch makes the check more robust.  If the device was
disconnected at any time during enumeration, we will now skip the
full-speed handover.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Zdenek Kabelac <zkabelac@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 89f23d51 ]

Similar to commit d595259f ("usb-storage: Add ignore-residue quirk for
Initio INIC-3619") for INIC-3169 in unusual_devs.h but INIC-3069 already
present in unusual_uas.h. Both in same controller IC family.

Issue is that MakeMKV fails during key exchange with installed bluray drive
with following error:

002004:0000 Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED'
occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:0'
Signed-off-by: Alan Swanson <reiver@improbability.net>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit a3507e48 ]

The TSL2563 driver provides three iio channels, two of which are raw ADC
channels (channel 0 and channel 1) in the device and the remaining one
is calculated by the two.  The ADC channel 0 only supports programmable
interrupt with threshold settings and this driver supports the event but
the generated event code does not contain the corresponding iio channel
type.

This is going to change userspace ABI.  Hopefully fixing this to be
what it should always have been won't break any userspace code.

Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 105967ad ]

gcc-7 points out an older regression:

drivers/staging/iio/resolver/ad2s1210.c: In function 'ad2s1210_read_raw':
drivers/staging/iio/resolver/ad2s1210.c:515:42: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]

The original code had 'unsigned short' here, but incorrectly got
converted to 'bool'. This reverts the regression and uses a normal
type instead.

Fixes: 29148543 ("staging:iio:resolver:ad2s1210 minimal chan spec conversion.")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit cd5a6a4f ]

Make usb_hc_died() clear the HCD_FLAG_RH_RUNNING flag for the shared
HCD and set HCD_FLAG_DEAD for it, in analogy with what is done for
the primary one.

Among other thigs, this prevents check_root_hub_suspended() from
returning -EBUSY for dead HCDs which helps to work around system
suspend issues in some situations.

This actually fixes occasional suspend failures on one of my test
machines.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 3b6bcd3d ]

This adds a new ATEN device id for a new pl2303-based device.
Reported-by: Peter Kuo <PeterKuo@aten.com.tw>
Cc: stable <stable@vger.kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 9585e340 ]

The German Telekom offers a ZigBee USB Stick under the brand name Qivicon
for their SmartHome Home Base in its 1. Generation. The productId is not
known by the according kernel module, this patch adds support for it.
Signed-off-by: Stefan Triller <github@stefantriller.de>
Reviewed-by: Frans Klaver <fransklaver@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit fd1b8668 ]

Add device id for D-Link DWM-222.

Cc: stable@vger.kernel.org
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 1feb2616 ]

The client was freeing the nfs4_ff_layout_ds, but not the contained
nfs4_ff_ds_version array.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 68227c03 ]

Before the patch, the flock flag could remain uninitialized for the
lifespan of the fuse_file allocation. Unless set to true in
fuse_file_flock(), it would remain in an indeterminate state until read in
an if statement in fuse_release_common(). This could consequently lead to
taking an unexpected branch in the code.

The bug was discovered by a runtime instrumentation designed to detect use
of uninitialized memory in the kernel.
Signed-off-by: Mateusz Jurczyk <mjurczyk@google.com>
Fixes: 37fb3a30 ("fuse: fix flock")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 978d13d6 ]

This patch fixes a bug associated with iscsit_reset_np_thread()
that can occur during parallel configfs rmdir of a single iscsi_np
used across multiple iscsi-target instances, that would result in
hung task(s) similar to below where configfs rmdir process context
was blocked indefinately waiting for iscsi_np->np_restart_comp
to finish:

[ 6726.112076] INFO: task dcp_proxy_node_:15550 blocked for more than 120 seconds.
[ 6726.119440]       Tainted: G        W  O     4.1.26-3321 #2
[ 6726.125045] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 6726.132927] dcp_proxy_node_ D ffff8803f202bc88     0 15550      1 0x00000000
[ 6726.140058]  ffff8803f202bc88 ffff88085c64d960 ffff88083b3b1ad0 ffff88087fffeb08
[ 6726.147593]  ffff8803f202c000 7fffffffffffffff ffff88083f459c28 ffff88083b3b1ad0
[ 6726.155132]  ffff88035373c100 ffff8803f202bca8 ffffffff8168ced2 ffff8803f202bcb8
[ 6726.162667] Call Trace:
[ 6726.165150]  [<ffffffff8168ced2>] schedule+0x32/0x80
[ 6726.170156]  [<ffffffff8168f5b4>] schedule_timeout+0x214/0x290
[ 6726.176030]  [<ffffffff810caef2>] ? __send_signal+0x52/0x4a0
[ 6726.181728]  [<ffffffff8168d7d6>] wait_for_completion+0x96/0x100
[ 6726.187774]  [<ffffffff810e7c80>] ? wake_up_state+0x10/0x10
[ 6726.193395]  [<ffffffffa035d6e2>] iscsit_reset_np_thread+0x62/0xe0 [iscsi_target_mod]
[ 6726.201278]  [<ffffffffa0355d86>] iscsit_tpg_disable_portal_group+0x96/0x190 [iscsi_target_mod]
[ 6726.210033]  [<ffffffffa0363f7f>] lio_target_tpg_store_enable+0x4f/0xc0 [iscsi_target_mod]
[ 6726.218351]  [<ffffffff81260c5a>] configfs_write_file+0xaa/0x110
[ 6726.224392]  [<ffffffff811ea364>] vfs_write+0xa4/0x1b0
[ 6726.229576]  [<ffffffff811eb111>] SyS_write+0x41/0xb0
[ 6726.234659]  [<ffffffff8169042e>] system_call_fastpath+0x12/0x71

It would happen because each iscsit_reset_np_thread() sets state
to ISCSI_NP_THREAD_RESET, sends SIGINT, and then blocks waiting
for completion on iscsi_np->np_restart_comp.

However, if iscsi_np was active processing a login request and
more than a single iscsit_reset_np_thread() caller to the same
iscsi_np was blocked on iscsi_np->np_restart_comp, iscsi_np
kthread process context in __iscsi_target_login_thread() would
flush pending signals and only perform a single completion of
np->np_restart_comp before going back to sleep within transport
specific iscsit_transport->iscsi_accept_np code.

To address this bug, add a iscsi_np->np_reset_count and update
__iscsi_target_login_thread() to keep completing np->np_restart_comp
until ->np_reset_count has reached zero.
Reported-by: Gary Guo <ghg@datera.io>
Tested-by: Gary Guo <ghg@datera.io>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit ea8dc5b4 ]

On receiving text request iscsi-target allocates buffer for
payload in iscsit_handle_text_cmd() and assigns buffer pointer
to cmd->text_in_ptr, this buffer is currently freed in
iscsit_release_cmd(), if iscsi-target sets 'C' bit in text
response then it will receive another text request from the
initiator with ttt != 0xffffffff in this case iscsi-target
will find cmd using itt and call iscsit_setup_text_cmd()
which will set cmd->text_in_ptr to NULL without freeing
previously allocated buffer.

This patch fixes this issue by calling kfree(cmd->text_in_ptr)
in iscsit_setup_text_cmd() before assigning NULL to it.

For the first text request cmd->text_in_ptr is NULL as
cmd is memset to 0 in iscsit_allocate_cmd().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 75dddef3 ]

The RDMA subsystem can generate several thousand of these messages per
second eventually leading to a kernel crash.  Ratelimit these messages
to prevent this crash.

Doug said:
 "I've been carrying a version of this for several kernel versions. I
  don't remember when they started, but we have one (and only one) class
  of machines: Dell PE R730xd, that generate these errors. When it
  happens, without a rate limit, we get rcu timeouts and kernel oopses.
  With the rate limit, we just get a lot of annoying kernel messages but
  the machine continues on, recovers, and eventually the memory
  operations all succeed"

And:
 "> Well... why are all these EBUSY's occurring? It sounds inefficient
  > (at least) but if it is expected, normal and unavoidable then
  > perhaps we should just remove that message altogether?

  I don't have an answer to that question. To be honest, I haven't
  looked real hard. We never had this at all, then it started out of the
  blue, but only on our Dell 730xd machines (and it hits all of them),
  but no other classes or brands of machines. And we have our 730xd
  machines loaded up with different brands and models of cards (for
  instance one dedicated to mlx4 hardware, one for qib, one for mlx5, an
  ocrdma/cxgb4 combo, etc), so the fact that it hit all of the machines
  meant it wasn't tied to any particular brand/model of RDMA hardware.
  To me, it always smelled of a hardware oddity specific to maybe the
  CPUs or mainboard chipsets in these machines, so given that I'm not an
  mm expert anyway, I never chased it down.

  A few other relevant details: it showed up somewhere around 4.8/4.9 or
  thereabouts. It never happened before, but the prinkt has been there
  since the 3.18 days, so possibly the test to trigger this message was
  changed, or something else in the allocator changed such that the
  situation started happening on these machines?

  And, like I said, it is specific to our 730xd machines (but they are
  all identical, so that could mean it's something like their specific
  ram configuration is causing the allocator to hit this on these
  machine but not on other machines in the cluster, I don't want to say
  it's necessarily the model of chipset or CPU, there are other bits of
  identicalness between these machines)"

Link: http://lkml.kernel.org/r/499c0f6cc10d6eb829a67f2a4d75b4228a9b356e.1501695897.git.jtoppins@redhat.comSigned-off-by: Jonathan Toppins <jtoppins@redhat.com>
Reviewed-by: Doug Ledford <dledford@redhat.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 76401310 ]

When removing an element from the mempool, mark it as unpoisoned in KASAN
before verifying its contents for SLUB/SLAB debugging.  Otherwise KASAN
will flag the reads checking the element use-after-free writes as
use-after-free reads.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 7e5a6722 ]

The mmu_notifier_release() callback of KVM triggers cleaning up
the stage2 page table on kvm-arm. However there could be other
notifier callbacks in parallel with the mmu_notifier_release(),
which could cause the call backs ending up in an empty stage2
page table. Make sure we check it for all the notifier callbacks.

Cc: stable@vger.kernel.org
Fixes: commit 293f2936 ("kvm-arm: Unmap shadow pagetables properly")
Reported-by: Alex Graf <agraf@suse.de>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit fc290a11 ]

This fixes another cause of random segfaults and bus errors that may
occur while running perf with the callgraph option.

Critical sections beginning with spin_lock_irqsave() raise the interrupt
level to PIL_NORMAL_MAX (14) and intentionally do not block performance
counter interrupts, which arrive at PIL_NMI (15).

But some sections of code are "super critical" with respect to perf
because the perf_callchain_user() path accesses user space and may cause
TLB activity as well as faults as it unwinds the user stack.

One particular critical section occurs in switch_mm:

        spin_lock_irqsave(&mm->context.lock, flags);
        ...
        load_secondary_context(mm);
        tsb_context_switch(mm);
        ...
        spin_unlock_irqrestore(&mm->context.lock, flags);

If a perf interrupt arrives in between load_secondary_context() and
tsb_context_switch(), then perf_callchain_user() could execute with
the context ID of one process, but with an active TSB for a different
process. When the user stack is accessed, it is very likely to
incur a TLB miss, since the h/w context ID has been changed. The TLB
will then be reloaded with a translation from the TSB for one process,
but using a context ID for another process. This exposes memory from
one process to another, and since it is a mapping for stack memory,
this usually causes the new process to crash quickly.

This super critical section needs more protection than is provided
by spin_lock_irqsave() since perf interrupts must not be allowed in.

Since __tsb_context_switch already goes through the trouble of
disabling interrupts completely, we fix this by moving the secondary
context load down into this better protected region.

Orabug: 25577560
Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com>
Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit c27927e3 ]

Updates to tp_reserve can race with reads of the field in
packet_set_ring. Avoid this by holding the socket lock during
updates in setsockopt PACKET_RESERVE.

This bug was discovered by syzkaller.

Fixes: 8913336a ("packet: add PACKET_RESERVE sockopt")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 8d63bee6 ]

skb_warn_bad_offload triggers a warning when an skb enters the GSO
stack at __skb_gso_segment that does not have CHECKSUM_PARTIAL
checksum offload set.

Commit b2504a5d ("net: reduce skb_warn_bad_offload() noise")
observed that SKB_GSO_DODGY producers can trigger the check and
that passing those packets through the GSO handlers will fix it
up. But, the software UFO handler will set ip_summed to
CHECKSUM_NONE.

When __skb_gso_segment is called from the receive path, this
triggers the warning again.

Make UFO set CHECKSUM_UNNECESSARY instead of CHECKSUM_NONE. On
Tx these two are equivalent. On Rx, this better matches the
skb state (checksum computed), as CHECKSUM_NONE here means no
checksum computed.

See also this thread for context:
http://patchwork.ozlabs.org/patch/799015/

Fixes: b2504a5d ("net: reduce skb_warn_bad_offload() noise")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit b0a0c256 ]

While testing some other work that required JIT modifications, I
run into test_bpf causing a hang when JIT enabled on s390. The
problematic test case was the one from ddc665a4 (bpf, arm64:
fix jit branch offset related to ldimm64), and turns out that we
do have a similar issue on s390 as well. In bpf_jit_prog() we
update next instruction address after returning from bpf_jit_insn()
with an insn_count. bpf_jit_insn() returns either -1 in case of
error (e.g. unsupported insn), 1 or 2. The latter is only the
case for ldimm64 due to spanning 2 insns, however, next address
is only set to i + 1 not taking actual insn_count into account,
thus fix is to use insn_count instead of 1. bpf_jit_enable in
mode 2 provides also disasm on s390:

Before fix:

  000003ff800349b6: a7f40003   brc     15,3ff800349bc                 ; target
  000003ff800349ba: 0000               unknown
  000003ff800349bc: e3b0f0700024       stg     %r11,112(%r15)
  000003ff800349c2: e3e0f0880024       stg     %r14,136(%r15)
  000003ff800349c8: 0db0               basr    %r11,%r0
  000003ff800349ca: c0ef00000000       llilf   %r14,0
  000003ff800349d0: e320b0360004       lg      %r2,54(%r11)
  000003ff800349d6: e330b03e0004       lg      %r3,62(%r11)
  000003ff800349dc: ec23ffeda065       clgrj   %r2,%r3,10,3ff800349b6 ; jmp
  000003ff800349e2: e3e0b0460004       lg      %r14,70(%r11)
  000003ff800349e8: e3e0b04e0004       lg      %r14,78(%r11)
  000003ff800349ee: b904002e   lgr     %r2,%r14
  000003ff800349f2: e3b0f0700004       lg      %r11,112(%r15)
  000003ff800349f8: e3e0f0880004       lg      %r14,136(%r15)
  000003ff800349fe: 07fe               bcr     15,%r14

After fix:

  000003ff80ef3db4: a7f40003   brc     15,3ff80ef3dba
  000003ff80ef3db8: 0000               unknown
  000003ff80ef3dba: e3b0f0700024       stg     %r11,112(%r15)
  000003ff80ef3dc0: e3e0f0880024       stg     %r14,136(%r15)
  000003ff80ef3dc6: 0db0               basr    %r11,%r0
  000003ff80ef3dc8: c0ef00000000       llilf   %r14,0
  000003ff80ef3dce: e320b0360004       lg      %r2,54(%r11)
  000003ff80ef3dd4: e330b03e0004       lg      %r3,62(%r11)
  000003ff80ef3dda: ec230006a065       clgrj   %r2,%r3,10,3ff80ef3de6 ; jmp
  000003ff80ef3de0: e3e0b0460004       lg      %r14,70(%r11)
  000003ff80ef3de6: e3e0b04e0004       lg      %r14,78(%r11)          ; target
  000003ff80ef3dec: b904002e   lgr     %r2,%r14
  000003ff80ef3df0: e3b0f0700004       lg      %r11,112(%r15)
  000003ff80ef3df6: e3e0f0880004       lg      %r14,136(%r15)
  000003ff80ef3dfc: 07fe               bcr     15,%r14

test_bpf.ko suite runs fine after the fix.

Fixes: 05462310 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit ed254971 ]

If the sender switches the congestion control during ECN-triggered
cwnd-reduction state (CA_CWR), upon exiting recovery cwnd is set to
the ssthresh value calculated by the previous congestion control. If
the previous congestion control is BBR that always keep ssthresh
to TCP_INIFINITE_SSTHRESH, cwnd ends up being infinite. The safe
step is to avoid assigning invalid ssthresh value when recovery ends.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

ipv4: Should use consistent conditional judgement for ip fragment in __ip_append_data and ip_finish_output

[ Upstream commit 0a28cfd5 ]

There is an inconsistent conditional judgement in __ip_append_data and
ip_finish_output functions, the variable length in __ip_append_data just
include the length of application's payload and udp header, don't include
the length of ip header, but in ip_finish_output use
(skb->len > ip_skb_dst_mtu(skb)) as judgement, and skb->len include the
length of ip header.

That causes some particular application's udp payload whose length is
between (MTU - IP Header) and MTU were fragmented by ip_fragment even
though the rst->dev support UFO feature.

Add the length of ip header to length in __ip_append_data to keep
consistent conditional judgement as ip_finish_output for ip fragment.
Signed-off-by: Zheng Li <james.z.li@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit f073bdc5 ]

The VM_BUG_ON() check in move_freepages() checks whether the node id of
a page matches the node id of its zone.  However, it does this before
having checked whether the struct page pointer refers to a valid struct
page to begin with.  This is guaranteed in most cases, but may not be
the case if CONFIG_HOLES_IN_ZONE=y.

So reorder the VM_BUG_ON() with the pfn_valid_within() check.

Link: http://lkml.kernel.org/r/1481706707-6211-2-git-send-email-ard.biesheuvel@linaro.orgSigned-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Yisheng Xie <xieyisheng1@huawei.com>
Cc: Robert Richter <rrichter@cavium.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 2d39b3cd ]

Since commit 00cd5c37 ("ptrace: permit ptracing of /sbin/init") we
can now trace init processes.  init is initially protected with
SIGNAL_UNKILLABLE which will prevent fatal signals such as SIGSTOP, but
there are a number of paths during tracing where SIGNAL_UNKILLABLE can
be implicitly cleared.

This can result in init becoming stoppable/killable after tracing.  For
example, running:

  while true; do kill -STOP 1; done &
  strace -p 1

and then stopping strace and the kill loop will result in init being
left in state TASK_STOPPED.  Sending SIGCONT to init will resume it, but
init will now respond to future SIGSTOP signals rather than ignoring
them.

Make sure that when setting SIGNAL_STOP_CONTINUED/SIGNAL_STOP_STOPPED
that we don't clear SIGNAL_UNKILLABLE.

Link: http://lkml.kernel.org/r/20170104122017.25047-1-jamie.iles@oracle.comSigned-off-by: Jamie Iles <jamie.iles@oracle.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit da0510c4 ]

The build of frv allmodconfig was failing with the errors like:

  /tmp/cc0JSPc3.s: Assembler messages:
  /tmp/cc0JSPc3.s:1839: Error: symbol `.LSLT0' is already defined
  /tmp/cc0JSPc3.s:1842: Error: symbol `.LASLTP0' is already defined
  /tmp/cc0JSPc3.s:1969: Error: symbol `.LELTP0' is already defined
  /tmp/cc0JSPc3.s:1970: Error: symbol `.LELT0' is already defined

Commit 866ced95 ("kbuild: Support split debug info v4") introduced
splitting the debug info and keeping that in a separate file.  Somehow,
the frv-linux gcc did not like that and I am guessing that instead of
splitting it started copying.  The first report about this is at:

  https://lists.01.org/pipermail/kbuild-all/2015-July/010527.html.

I will try and see if this can work with frv and if still fails I will
open a bug report with gcc.  But meanwhile this is the easiest option to
solve build failure of frv.

Fixes: 866ced95 ("kbuild: Support split debug info v4")
Link: http://lkml.kernel.org/r/1482062348-5352-1-git-send-email-sudipm.mukherjee@gmail.comSigned-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit bb1107f7 ]

Andrey Konovalov has reported the following warning triggered by the
syzkaller fuzzer.

  WARNING: CPU: 1 PID: 9935 at mm/page_alloc.c:3511 __alloc_pages_nodemask+0x159c/0x1e20
  Kernel panic - not syncing: panic_on_warn set ...
  CPU: 1 PID: 9935 Comm: syz-executor0 Not tainted 4.9.0-rc7+ #34
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
  Call Trace:
    __alloc_pages_slowpath mm/page_alloc.c:3511
    __alloc_pages_nodemask+0x159c/0x1e20 mm/page_alloc.c:3781
    alloc_pages_current+0x1c7/0x6b0 mm/mempolicy.c:2072
    alloc_pages include/linux/gfp.h:469
    kmalloc_order+0x1f/0x70 mm/slab_common.c:1015
    kmalloc_order_trace+0x1f/0x160 mm/slab_common.c:1026
    kmalloc_large include/linux/slab.h:422
    __kmalloc+0x210/0x2d0 mm/slub.c:3723
    kmalloc include/linux/slab.h:495
    ep_write_iter+0x167/0xb50 drivers/usb/gadget/legacy/inode.c:664
    new_sync_write fs/read_write.c:499
    __vfs_write+0x483/0x760 fs/read_write.c:512
    vfs_write+0x170/0x4e0 fs/read_write.c:560
    SYSC_write fs/read_write.c:607
    SyS_write+0xfb/0x230 fs/read_write.c:599
    entry_SYSCALL_64_fastpath+0x1f/0xc2

The issue is caused by a lack of size check for the request size in
ep_write_iter which should be fixed.  It, however, points to another
problem, that SLUB defines KMALLOC_MAX_SIZE too large because the its
KMALLOC_SHIFT_MAX is (MAX_ORDER + PAGE_SHIFT) which means that the
resulting page allocator request might be MAX_ORDER which is too large
(see __alloc_pages_slowpath).

The same applies to the SLOB allocator which allows even larger sizes.
Make sure that they are capped properly and never request more than
MAX_ORDER order.

Link: http://lkml.kernel.org/r/20161220130659.16461-2-mhocko@kernel.orgSigned-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 270c8cf1 ]

ARM has a few system calls (most notably mmap) for which the names of
the functions which are referenced in the syscall table do not match the
names of the syscall tracepoints.  As a consequence of this, these
tracepoints are not made available.  Implement
arch_syscall_match_sym_name to fix this and allow tracing even these
system calls.
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 6bf6b0aa ]

If blk_mq_init_queue() returns an error, it gets assigned to
vblk->disk->queue. Then, when we call put_disk(), we end up calling
blk_put_queue() with the ERR_PTR, causing a bad dereference. Fix it by
only assigning to vblk->disk->queue on success.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit c7702b8c ]

There is a race condition with qla2xxx optrom functions where one thread
might modify optrom buffer, optrom_state while other thread is still
reading from it.

In couple of crashes, it was found that we had successfully passed the
following 'if' check where we confirm optrom_state to be
QLA_SREADING. But by the time we acquired mutex lock to proceed with
memory_read_from_buffer function, some other thread/process had already
modified that option rom buffer and optrom_state from QLA_SREADING to
QLA_SWAITING. Then we got ha->optrom_buffer 0x0 and crashed the system:

        if (ha->optrom_state != QLA_SREADING)
                return 0;

        mutex_lock(&ha->optrom_mutex);
        rval = memory_read_from_buffer(buf, count, &off, ha->optrom_buffer,
            ha->optrom_region_size);
        mutex_unlock(&ha->optrom_mutex);

With current optrom function we get following crash due to a race
condition:

[ 1479.466679] BUG: unable to handle kernel NULL pointer dereference at           (null)
[ 1479.466707] IP: [<ffffffff81326756>] memcpy+0x6/0x110
[...]
[ 1479.473673] Call Trace:
[ 1479.474296]  [<ffffffff81225cbc>] ? memory_read_from_buffer+0x3c/0x60
[ 1479.474941]  [<ffffffffa01574dc>] qla2x00_sysfs_read_optrom+0x9c/0xc0 [qla2xxx]
[ 1479.475571]  [<ffffffff8127e76b>] read+0xdb/0x1f0
[ 1479.476206]  [<ffffffff811fdf9e>] vfs_read+0x9e/0x170
[ 1479.476839]  [<ffffffff811feb6f>] SyS_read+0x7f/0xe0
[ 1479.477466]  [<ffffffff816964c9>] system_call_fastpath+0x16/0x1b

Below patch modifies qla2x00_sysfs_read_optrom,
qla2x00_sysfs_write_optrom functions to get the mutex_lock before
checking ha->optrom_state to avoid similar crashes.

The patch was applied and tested and same crashes were no longer
observed again.
Tested-by: Milan P. Gandhi <mgandhi@redhat.com>
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit fac69d0e ]

Add the missing declarations of basic string functions to string.h to allow
a clean build.

Fixes: 5be86566 ("String-handling functions for the new x86 setup code.")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Link: http://lkml.kernel.org/r/1483781911-21399-1-git-send-email-hofrat@osadl.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit f5992b72 ]

The driver's ndo_get_stats64() method is not always called under RTNL.
So it can race with driver close or ethtool reconfigurations.  Fix the
race condition by taking tp->lock spinlock in tg3_free_consistent()
when freeing the tp->hw_stats memory block.  tg3_get_stats64() is
already taking tp->lock.
Reported-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 0f1f9cbc ]

The R8A7740 GEther controller supports the packet checksum offloading
but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740
data,  thus CSMR isn't cleared...

Fixes: 73a0d907 ("net: sh_eth: add support R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 93be2b74 ]

gcc-7 complains that wl3501_cs passes NULL into a function that
then uses the argument as the input for memcpy:

drivers/net/wireless/wl3501_cs.c: In function 'wl3501_get_scan':
include/net/iw_handler.h:559:3: error: argument 2 null where non-null expected [-Werror=nonnull]
   memcpy(stream + point_len, extra, iwe->u.data.length);

This works fine here because iwe->u.data.length is guaranteed to be 0
and the memcpy doesn't actually have an effect.

Making the length check explicit avoids the warning and should have
no other effect here.

Also check the pointer itself, since otherwise we get warnings
elsewhere in the code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 9d53caec ]

A large sun4v SPARC system may have moments of intensive xcall activities,
usually caused by unmapping many pages on many CPUs concurrently. This can
flood receivers with CPU mondo interrupts for an extended period, causing
some unlucky senders to hit send-mondo timeout. This problem gets worse
as cpu count increases because sometimes mappings must be invalidated on
all CPUs, and sometimes all CPUs may gang up on a single CPU.

But a busy system is not a broken system. In the above scenario, as long
as the receiver is making forward progress processing mondo interrupts,
the sender should continue to retry.

This patch implements the receiver's forward progress meter by introducing
a per cpu counter 'cpu_mondo_counter[cpu]' where 'cpu' is in the range
of 0..NR_CPUS. The receiver increments its counter as soon as it receives
a mondo and the sender tracks the receiver's counter. If the receiver has
stopped making forward progress when the retry limit is reached, the sender
declares send-mondo-timeout and panic; otherwise, the receiver is allowed
to keep making forward progress.

In addition, it's been observed that PCIe hotplug events generate Correctable
Errors that are handled by hypervisor and then OS. Hypervisor 'borrows'
a guest cpu strand briefly to provide the service. If the cpu strand is
simultaneously the only cpu targeted by a mondo, it may not be available
for the mondo in 20msec, causing SUN4V mondo timeout. It appears that 1 second
is the agreed wait time between hypervisor and guest OS, this patch makes
the adjustment.

Orabug: 25476541
Orabug: 26417466
Signed-off-by: Jane Chu <jane.chu@oracle.com>
Reviewed-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Reviewed-by: Rob Gardner <rob.gardner@oracle.com>
Reviewed-by: Thomas Tai <thomas.tai@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit dfa523ae ]

Add a flag to indicate if a queue is rate-limited. Test the flag in
NAPI poll handler and avoid rescheduling the queue if true, otherwise
we risk locking up the host. The rescheduling will be done in the
timer callback function.
Reported-by: Jean-Louis Dupond <jean-louis@dupond.be>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Tested-by: Jean-Louis Dupond <jean-louis@dupond.be>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 7b9a88a3 ]

The PHY library does not deal very well with bind and unbind events. The first
thing we would see is that we were not properly canceling the PHY state machine
workqueue, so we would be crashing while dereferencing phydev->drv since there
is no driver attached anymore.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 7ad813f2 ]

Marc reported that he was not getting the PHY library adjust_link()
callback function to run when calling phy_stop() + phy_disconnect()
which does not indeed happen because we set the state machine to
PHY_HALTED but we don't get to run it to process this state past that
point.

Fix this with a synchronous call to phy_state_machine() in order to have
the state machine actually act on PHY_HALTED, set the PHY device's link
down, turn the network device's carrier off and finally call the
adjust_link() function.
Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Fixes: a390d1f3 ("phylib: convert state_queue work to delayed_work")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 6b84202c ]

Commit b1f5bfc2 ("sctp: don't dereference ptr before leaving
_sctp_walk_{params, errors}()") tried to fix the issue that it
may overstep the chunk end for _sctp_walk_{params, errors} with
'chunk_end > offset(length) + sizeof(length)'.

But it introduced a side effect: When processing INIT, it verifies
the chunks with 'param.v == chunk_end' after iterating all params
by sctp_walk_params(). With the check 'chunk_end > offset(length)
+ sizeof(length)', it would return when the last param is not yet
accessed. Because the last param usually is fwdtsn supported param
whose size is 4 and 'chunk_end == offset(length) + sizeof(length)'

This is a badly issue even causing sctp couldn't process 4-shakes.
Client would always get abort when connecting to server, due to
the failure of INIT chunk verification on server.

The patch is to use 'chunk_end <= offset(length) + sizeof(length)'
instead of 'chunk_end < offset(length) + sizeof(length)' for both
_sctp_walk_params and _sctp_walk_errors.

Fixes: b1f5bfc2 ("sctp: don't dereference ptr before leaving _sctp_walk_{params, errors}()")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit b1f5bfc2 ]

If the length field of the iterator (|pos.p| or |err|) is past the end
of the chunk, we shouldn't access it.

This bug has been detected by KMSAN. For the following pair of system
calls:

  socket(PF_INET6, SOCK_STREAM, 0x84 /* IPPROTO_??? */) = 3
  sendto(3, "A", 1, MSG_OOB, {sa_family=AF_INET6, sin6_port=htons(0),
         inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0,
         sin6_scope_id=0}, 28) = 1

the tool has reported a use of uninitialized memory:

  ==================================================================
  BUG: KMSAN: use of uninitialized memory in sctp_rcv+0x17b8/0x43b0
  CPU: 1 PID: 2940 Comm: probe Not tainted 4.11.0-rc5+ #2926
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs
  01/01/2011
  Call Trace:
   <IRQ>
   __dump_stack lib/dump_stack.c:16
   dump_stack+0x172/0x1c0 lib/dump_stack.c:52
   kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:927
   __msan_warning_32+0x61/0xb0 mm/kmsan/kmsan_instr.c:469
   __sctp_rcv_init_lookup net/sctp/input.c:1074
   __sctp_rcv_lookup_harder net/sctp/input.c:1233
   __sctp_rcv_lookup net/sctp/input.c:1255
   sctp_rcv+0x17b8/0x43b0 net/sctp/input.c:170
   sctp6_rcv+0x32/0x70 net/sctp/ipv6.c:984
   ip6_input_finish+0x82f/0x1ee0 net/ipv6/ip6_input.c:279
   NF_HOOK ./include/linux/netfilter.h:257
   ip6_input+0x239/0x290 net/ipv6/ip6_input.c:322
   dst_input ./include/net/dst.h:492
   ip6_rcv_finish net/ipv6/ip6_input.c:69
   NF_HOOK ./include/linux/netfilter.h:257
   ipv6_rcv+0x1dbd/0x22e0 net/ipv6/ip6_input.c:203
   __netif_receive_skb_core+0x2f6f/0x3a20 net/core/dev.c:4208
   __netif_receive_skb net/core/dev.c:4246
   process_backlog+0x667/0xba0 net/core/dev.c:4866
   napi_poll net/core/dev.c:5268
   net_rx_action+0xc95/0x1590 net/core/dev.c:5333
   __do_softirq+0x485/0x942 kernel/softirq.c:284
   do_softirq_own_stack+0x1c/0x30 arch/x86/entry/entry_64.S:902
   </IRQ>
   do_softirq kernel/softirq.c:328
   __local_bh_enable_ip+0x25b/0x290 kernel/softirq.c:181
   local_bh_enable+0x37/0x40 ./include/linux/bottom_half.h:31
   rcu_read_unlock_bh ./include/linux/rcupdate.h:931
   ip6_finish_output2+0x19b2/0x1cf0 net/ipv6/ip6_output.c:124
   ip6_finish_output+0x764/0x970 net/ipv6/ip6_output.c:149
   NF_HOOK_COND ./include/linux/netfilter.h:246
   ip6_output+0x456/0x520 net/ipv6/ip6_output.c:163
   dst_output ./include/net/dst.h:486
   NF_HOOK ./include/linux/netfilter.h:257
   ip6_xmit+0x1841/0x1c00 net/ipv6/ip6_output.c:261
   sctp_v6_xmit+0x3b7/0x470 net/sctp/ipv6.c:225
   sctp_packet_transmit+0x38cb/0x3a20 net/sctp/output.c:632
   sctp_outq_flush+0xeb3/0x46e0 net/sctp/outqueue.c:885
   sctp_outq_uncork+0xb2/0xd0 net/sctp/outqueue.c:750
   sctp_side_effects net/sctp/sm_sideeffect.c:1773
   sctp_do_sm+0x6962/0x6ec0 net/sctp/sm_sideeffect.c:1147
   sctp_primitive_ASSOCIATE+0x12c/0x160 net/sctp/primitive.c:88
   sctp_sendmsg+0x43e5/0x4f90 net/sctp/socket.c:1954
   inet_sendmsg+0x498/0x670 net/ipv4/af_inet.c:762
   sock_sendmsg_nosec net/socket.c:633
   sock_sendmsg net/socket.c:643
   SYSC_sendto+0x608/0x710 net/socket.c:1696
   SyS_sendto+0x8a/0xb0 net/socket.c:1664
   do_syscall_64+0xe6/0x130 arch/x86/entry/common.c:285
   entry_SYSCALL64_slow_path+0x25/0x25 arch/x86/entry/entry_64.S:246
  RIP: 0033:0x401133
  RSP: 002b:00007fff6d99cd38 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
  RAX: ffffffffffffffda RBX: 00000000004002b0 RCX: 0000000000401133
  RDX: 0000000000000001 RSI: 0000000000494088 RDI: 0000000000000003
  RBP: 00007fff6d99cd90 R08: 00007fff6d99cd50 R09: 000000000000001c
  R10: 0000000000000001 R11: 0000000000000246 R12: 0000000000000000
  R13: 00000000004063d0 R14: 0000000000406460 R15: 0000000000000000
  origin:
   save_stack_trace+0x37/0x40 arch/x86/kernel/stacktrace.c:59
   kmsan_save_stack_with_flags mm/kmsan/kmsan.c:302
   kmsan_internal_poison_shadow+0xb1/0x1a0 mm/kmsan/kmsan.c:198
   kmsan_poison_shadow+0x6d/0xc0 mm/kmsan/kmsan.c:211
   slab_alloc_node mm/slub.c:2743
   __kmalloc_node_track_caller+0x200/0x360 mm/slub.c:4351
   __kmalloc_reserve net/core/skbuff.c:138
   __alloc_skb+0x26b/0x840 net/core/skbuff.c:231
   alloc_skb ./include/linux/skbuff.h:933
   sctp_packet_transmit+0x31e/0x3a20 net/sctp/output.c:570
   sctp_outq_flush+0xeb3/0x46e0 net/sctp/outqueue.c:885
   sctp_outq_uncork+0xb2/0xd0 net/sctp/outqueue.c:750
   sctp_side_effects net/sctp/sm_sideeffect.c:1773
   sctp_do_sm+0x6962/0x6ec0 net/sctp/sm_sideeffect.c:1147
   sctp_primitive_ASSOCIATE+0x12c/0x160 net/sctp/primitive.c:88
   sctp_sendmsg+0x43e5/0x4f90 net/sctp/socket.c:1954
   inet_sendmsg+0x498/0x670 net/ipv4/af_inet.c:762
   sock_sendmsg_nosec net/socket.c:633
   sock_sendmsg net/socket.c:643
   SYSC_sendto+0x608/0x710 net/socket.c:1696
   SyS_sendto+0x8a/0xb0 net/socket.c:1664
   do_syscall_64+0xe6/0x130 arch/x86/entry/common.c:285
   return_from_SYSCALL_64+0x0/0x6a arch/x86/entry/entry_64.S:246
  ==================================================================
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit e90ce2fc ]

In dccp_feat_init, when ccid_get_builtin_ccids failsto alloc
memory for rx.val, it should free tx.val before returning an
error.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit b7953d3c ]

The patch "dccp: fix a memleak that dccp_ipv6 doesn't put reqsk
properly" fixed reqsk refcnt leak for dccp_ipv6. The same issue
exists on dccp_ipv4.

This patch is to fix it for dccp_ipv4.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>