Generate xGMI iolink for upper level usage
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update the iolink type defines according to the new thunk spec
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Thunk will generate the XGMI topology information when necessary with the hive_id
for each specified device
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Retrieve hive_id from amdgpu device

v2: compile fix
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

KFD need to get hive id from amdgpu to build up the XGMI topology
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Driver will save an array of XGMI hive info, each hive will have a list of devices
that have the same hive ID.
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add dummy function for xgmi function interface with psp
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Place holder for XGMI support
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

On hives with xgmi enabled, the fb_location aperture is a size
which defines the total framebuffer size of all nodes in the
hive.  Each GPU in the hive has the same view via the fb_location
aperture.  GPU0 starts at offset (0 * segment size),
GPU1 starts at offset (1 * segment size), etc.

For access to local vram on each GPU, we need to take this offset into
account. This including on setting up GPUVM page table and GART table

v2: squash in "drm/amdgpu: Init correct fb region for none XGMI configuration"
Acked-by: Huang Rui <ray.huang@amd.com>
Acked-by: Slava Abramov <slava.abramov@amd.com>
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>

Used to populate the xgmi info on vega20.

v2: PF_MAX_REGION is val - 1 (Ray)
Acked-by: Huang Rui <ray.huang@amd.com>
Acked-by: Slava Abramov <slava.abramov@amd.com>
Reviewed-by :Shaoyun liu <Shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by :Shaoyun liu <Shaoyun.liu@amd.com>

Initial pass at a structure to store xgmi info.  xgmi is a high
speed cross gpu interconnect.
Acked-by: Huang Rui <ray.huang@amd.com>
Acked-by: Slava Abramov <slava.abramov@amd.com>
Reviewed-by :Shaoyun liu <Shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>

Correct the definition based on vega20 register spec
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

since we use PSP to program IH regs now
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Otherwise we might run into a use after free during bulk move.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fix SDMA hang in prt mode, clear XNACK_WATERMARK in reg SDMA0_UTCL1_WATERMK to avoid the issue

Affected ASICs: VEGA10 VEGA12 RV1 RV2

v2: add reg clear for SDMA1
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Tested-by: Yukun Li <yukun1.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

do_div expects the 1st argument in 64bit instead of 32bit.
Drop the usage of do_div as it seems unnecessary.

V2: drop usage of do_div completely
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch fixes following warnings.

./drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c:3011:
warning: Excess function parameter 'dev' description
in 'amdgpu_vm_get_task_info'

./drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c:3012:
warning: Function parameter or member 'adev' not
described in 'amdgpu_vm_get_task_info'

./drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c:3012:
warning: Excess function parameter 'dev' description
in 'amdgpu_vm_get_task_info'
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The intent of two commits was lost in the last rebase:

810955ba drm/amdgpu: Fix acquiring VM on large-BAR systems
b5d21aac drm/amdgpu: Don't use shadow BO for compute context

This commit restores the original behaviour:
* Don't set AMDGPU_GEM_CREATE_NO_CPU_ACCESS for page directories
  to allow them to be reused for compute VMs
* Don't create shadow BOs for page tables in compute VMs

v2: move more logic into amdgpu_vm_bo_param
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Tested-by: Kent Russell <Kent.Russell@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable the old AGP aperture to avoid GART mappings.

v2: don't enable it for SRIOV
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Only initialize KFD once by moving amdgpu_amdkfd_init from
amdgpu_pci_probe to amdgpu_init. This fixes kernel oopses and hangs
when booting multi-GPU systems.

Also removed some vestiges of KFD being its own module.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Existing debug dump are all invariant, new “low 32-bit of address”
dump is not invariant
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
There are same purpose transition events.

[How]
remove the redundant event log.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
The extraneous call to amdgpu_pm_compute_clocks is deprecated.

[How]
Remove it.
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Virtual sink is used when set mode happens on a disconnected display
to allow the mode set to proceed. This did not work with MST because
the logic for acquiring stream encoder uses stream signal to determine
the special handling is required, and stream signal is virtual instead
of DP in this case.

[How]
Use link type to decide instead.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Steven Chiu <Steven.Chiu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
The i2c and aux engines are similar, and should be placed
next to eachother for readability

[How]
Reorder the elements of the resource_pool struct
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Our implementation is functionally identical to DRM's

Note that instead of checking if the provided id is 0, the helper
follows through with the mode object search. However, It will still
return NULL, since 0 is not a valid object id, and missed searches
will return NULL.

[How]
Remove our implementation, and replace it with
drm_atomic_helper_best_encoder.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
AMD Stoney reference board, there are only 2 pipes (not include
underlay), and 3 connectors. resource creation, only
2 I2C/AUX engines are created. Within dc_link_aux_transfer, when
pin_data_en =2, refer to enengines[ddc_pin->pin_data->en] = NULL.
NULL point is referred later causing system crash.

[how]
each asic design has fixed number of ddc engines at hw side.
for each ddc engine, create its i2x/aux engine at sw side.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Enhance aux transition debugging information.

[How]
Added Aux request and reply event log.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Some display need disconnect delay. Adding this parameter for future use
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Although 4 unique register values exist for gamma modes, two are
actually the same (the two RAMs) It’s not possible for caller to
understand this HW specific behavior, so some parsing is necessary
in driver
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]Update Code to get DTN golden log check to pass for tests run after
DAL217 tests.
[How]Change how dcn10_log_hw_state function prints HW state info
(CM_GAMUT_REMAP_Cx_Cx registers) when GAMUT REMAP is in bypass mode.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
For supporting DP YCbCr 4:2:0 output.

[How]
Update mod_build_vsc_infopacket to support Pixel
Encoding/Colorimetry Format indication for VSC SDP rev5.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
We currently lock modeset by setting a boolean in dm. We want to lock
Based on what DC tells us.

[How]
Build stream_updates and plane_update based on what changed. Then we
call check_update_surfaces_for_stream() to get the update type
We lock only if update_type is not fast
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Otherwise we won't be able to use the AGP aperture.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Start to use the old AGP aperture for system memory access.

v2: Move that to amdgpu_ttm_alloc_gart
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Helper to figure out the location of the AGP BAR.

v2: fix a couple of bugs
v3: correctly add one to vram_end
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>