On some chips, baseband watchdog hangs are more common than others, and
the driver has support for handling them.
Interrupts even after a watchdog hang are also quite common, so there's
not much point in spamming the user's logfiles.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

5/10 MHz channel bandwidth is configured via the PLL clock, instead of
the AR_PHY_MODE register. Using that register is AR93xx specific, and
makes the mode incompatible with earlier chipsets.

In some early versions, these flags were apparently applied at the wrong
point in time and thus did not cause connectivity issues, however now
they are causing problems, as pointed out in this OpenWrt ticket:

https://dev.openwrt.org/ticket/14916Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Trivially reduces text size too.

$ size drivers/net/wireless/ath/ath9k/debug.o*
   text	   data	    bss	    dec	    hex	filename
  34436	   2528	   5128	  42092	   a46c	drivers/net/wireless/ath/ath9k/debug.o.new
  34464	   2528	   5128	  42120	   a488	drivers/net/wireless/ath/ath9k/debug.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Number of MAC hangs and stuck beacons were missing
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

PREPARE_[DELAYED_]WORK() are being phased out.  They have few users
and a nasty surprise in terms of reentrancy guarantee as workqueue
considers work items to be different if they don't have the same work
function.

Update rt2800usb.c to use INIT_WORK() instead of PREPARE_WORK().  As
the work item isn't in active use during rt2800usb_probe_hw(), this
doesn't cause any behavior difference.

It would probably be best to route this with other related updates
through the workqueue tree.

Only compile tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Even if we mark PS on, device still worked in normal mode. Patch
corrects that and now we send proper powertable command to device,
which put it in sleep mode when PS is on.
Reported-and-tested-by: Tino Keitel <tino.keitel@tikei.de>
Tested-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge reclaim check for 3945 & 4965. This add some more checks for
3945, most importantly N_RX notify.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We have only 5 tx queues on 3945, updating il->txq[5] results in
writing random value to HBUS_TARG_WRPTR register.

Additionally use spin lock to protect txq->write_ptr and
txq->need_update fields also modified in TX path.
Tested-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We don't perform OBSS scan internally. As we intend to use
corresponding feature in application, we will enable this flag.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While modifying timer, we need not delete timer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use SMP safe del_timer_sync instead of del_timer for cancelling
timers.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 handles the actual operations, so ath9k can just indicate
support for this. Based on initial tests, this combination seems to
work fine.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

removed following warnings-
drivers/net/wireless/airo.c:39: WARNING: Use #include <linux/io.h> instead of <asm/io.h>
drivers/net/wireless/airo.c:48: WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: Avinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is a relatively old Prism2 card which is correctly supported
by the hostap driver.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

linux/etherdevice.h was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Logically, config B43_BCMA_PIO should depend on B43. This also solves
the problem that sub options of b43 driver didn't indent correctly in
make menuconfig's ncurses window.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

commit 0baa0fd7
("rtlwifi: Convert core routines for addition of rtl8192se and
rtl8192de") removed setting HW_VAR_RCR, HW_VAR_MGT_FILTER and
HW_VAR_CTRL_FILTER. The last two are probably done because some hardware
does not support them. The first is probably a mistake. This patch adds
the missing set_hw_reg call.

For PCI support, rx_conf is not touched directly. Instead, get_hw_reg is
used to abstract between receive_config (for PCI) and rx_conf (for USB).

This was tested on a 10ec:8176 Realtek RTL8188CE (according to the
label on the mini-PCIe card). Before this patch, `iw wlan0 set monitor
otherbss` did not capture frames from other BSS's. After this patch, it
does print packets.
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The rtl*_set_check_bssid functions are mostly the same, but access the
RCR register in different ways. Use the get_hw_reg abstraction layer
(which reads rtlpci->receive_config for PCI devices and mac->rx_conf for
USB).

There is no functional change for cases where receive_config was
accessed directly. For rtl8192ce, there is still no change because
nothing modifies REG_RCR or receive_config. For rtl8192cu, it now also
applies changes to rx_conf from configure_filter, but that can be
considered a bug which is fixed later.
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is a typo here because the names are confusingly similar.  The
intent was sizeof(struct ieee80211_vht_cap) (size 12) but sizeof(struct
ieee80211_ht_cap) (size 32) was used.

Anway, it's cleaner to just specify the variable instead of the type.

Fixes: 5f6d5983 ('mwifiex: add VHT support for TDLS')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

This reverts commit 35582ad9.

This should not have been merged through this tree...
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Few minor comments.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We use the TLV flags as a handshake between the firmware
and the driver. These flags allow the firmware to advertise
its capabilities and API version.
Since we are running short of bits, we add a new
infrastructure which is more scalable, yet backward
compatible.

We make now the difference between API changes and the
capabilities. Both can have an index which allows to scale
at will.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This define is a leftover from dvm (in mvm, it
was replaced by MVM_UCODE_ALIVE_TIMEOUT).
Signed-off-by: Inbal Hacohen <Inbal.Hacohen@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

These values aren't used as the firmware values should be used,
so reading them is pointless and hides potential errors when
somebody uses these values. Leave them zero to make it clearer
that they can't be used. We can't remove the struct members as
the DVM driver does read the values from EEPROM/OTP and the
structure is shared between drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We should be iterating hdev->identity_resolving_keys in the
hci_remove_irk() function instead of hdev->long_term_keys. This patch
fixes the issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Error codes returned by cfg80211_chandef_dfs_required() are ignored
when trying to join an IBSS.  Fix this by printing an error and
returning.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We don't have to double check whether the parameters passed to
cfg80211_can_use_iftype_chan() are correct.  We should just make sure
they *are* when we call this function.

Remove the radar_detect argument check in
cfg80211_can_use_iftype_chan() to simplify the code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[keep braces around a long comment + single statement]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since mesh support for DFS channels was added, we also need to check
for DFS channels when performing a channel switch with
NL80211_IFTYPE_MESHPOINT.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[use switch statement, slight code cleanup]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Previously we were warning and using automatic when a driver sent an
update request with SMPS off.  This patch makes it possible for
drivers to disable SMPS at runtime, for whatever reason.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add the ieee80211_iface_limit and the ieee80211_iface_combination
structures to docbook.  Reformat the examples of combinations
slightly, so it looks a bit better on docbook.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

docbook (or one of its friends) gets confused with semi-colons in the
argument descriptions, causing it to think that the semi-colon is
marking a new section in the description of addr_mask in wiphy struct.

Prevent this by using hyphens instead of semi-colons in the mask
example.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Introduce NL80211_RRF_AUTO_BW rule flag. If this flag set
maximum available bandwidth should be calculated base on
contiguous rules and wider channels will be allowed to cross
multiple contiguous/overlapping frequency ranges.

In case of old kernels maximum bandwidth from regulatory
rule will be used, while there is no NL80211_RRF_AUTO_BW flag.

This fixes the previous commit 97524820
("cfg80211: regulatory introduce maximum bandwidth calculation")
which was found to be a problem for userspace API compatibility.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[edit commit log, use sizeof()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

With the addition of Resolvable Private Address (RPA) resolution
support for Bluetooth Low Energy connections, it makes sense to
increase the minor version of the Bluetooth core module.

The module version is not used anywhere, but it gives a nice extra
hint for debugging purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

For testing purposes it is useful to provide an option to change the
advertising channel map. So add a debugfs option to allow this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When binding RFCOMM socket with non-zero channel we're checking if
there is already any other socket which has the same channel number
assigned and then fail. This check does not consider situation where
we have another socket connected to remote device on given channel
number in which case we still should be able to bind local socket.

This patch changes __rfcomm_get_sock_by_addr() to return only sockets
in either BT_BOUND or BT_LISTEN states, also name is updated to better
describe what this function does now.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>