- 26 Jan, 2009 5 commits
-
-
Mark Lord authored
Fix a longstanding bug for the 8-port Marvell Sata controllers (508x/6081), where accesses to the upper 4 ports would cause lost-interrupts / timeouts for the lower 4-ports. With this patch, the 6081 boards should finally be reliable enough for mainstream use with Linux. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Tejun Heo authored
MCP5x family of controllers seem to share much more with nf2's as far as reset protocol is concerned. It requires heardreset to get the PHY going and classfication code report after hardreset is unreliable. Create a new board type MCP5x and use noclassify hardreset. SWNCQ is modified to inherit from this new type. This fixes hotplug regression reported in kernel bz#12351. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Tejun Heo authored
nv_nf2_hardreset() will be used by other flavors too. Rename it to nv_noclassify_hardreset(). Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Tejun Heo authored
Asus Pundit-R with atiixp controller has the second port missing and, very unusually, its status is stuck at 0x7f and all others at 0. This meanst that it fails TF access test but gets detected as a disk due to classification code check and then evades polling IDENTIFY presence detection thanks to the missing BSY in the status value causing excessive delays during boot. This patch makes libata-sff HSM set NODEV_HINT if the status is 0x7f to make polling IDENTIFY presence detection work for these machines. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Tejun Heo authored
The EH message for NODEV_HINT path was describing the opposite condition. Fix it. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
- 17 Jan, 2009 5 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infinibandLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: IB/ehca: Use consistent types for ehca_plpar_hcall9() IB/ehca: Fix printk format warnings from u64 type change IPoIB: Do not print error messages for multicast join retries IB/mlx4: Fix memory ordering problem when posting LSO sends mlx4_core: Fix min() warning IPoIB: Fix deadlock between ipoib_open() and child interface create IPoIB: Fix hang in napi_disable() if P_Key is never found
-
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: move wm8400-regulator's probe function to .devinit.text
-
Pavel Roskin authored
Reading 0 bytes from /sys/devices/platform/dell_rbu/image_type or /sys/devices/platform/dell_rbu/packet_size by an ordinary user causes an oops. Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Vegard Nossum authored
Plug this leak. Acked-by: David Howells <dhowells@redhat.com> Cc: James Morris <jmorris@namei.org> Cc: <stable@kernel.org> Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Uwe Kleine-König authored
A pointer to wm8400_regulator_probe is passed to the core via platform_driver_register and so the function must not disappear when the .init sections are discarded. Otherwise (if also having HOTPLUG=y) unbinding and binding a device to the driver via sysfs will result in an oops as does a device being registered late. An alternative to this patch is using platform_driver_probe instead of platform_driver_register plus removing the pointer to the probe function from the struct platform_driver. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
-
- 16 Jan, 2009 30 commits
-
-
Roland Dreier authored
-
Stephen Rothwell authored
ehca_plpar_hcall9() takes an unsigned long array, so make all callers pass that in. This fixes warnings introduced by commit fe333321 ("powerpc: Change u64/s64 to a long long integer type"), which changed u64 from unsigned long to unsigned long long. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Roland Dreier <rolandd@cisco.com>
-
Stephen Rothwell authored
Commit fe333321 ("powerpc: Change u64/s64 to a long long integer type") changed u64 from unsigned long to unsigned long long, which means that printk formats for printing u64 values should use "ll" instead of "l" to avoid warnings. Fix all the places affected by this in ehca. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Roland Dreier <rolandd@cisco.com>
-
Yossi Etigin authored
When IPoIB tries to join a multicast group, and the SA module's SM address handle is NULL (because of an SM change, etc), the join returns with -EAGAIN status. In that case, don't print an error message unless multicast debugging is enabled. Signed-off-by: Yossi Etigin <yosefe@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
-
Roland Dreier authored
The current work request posting code writes the LSO segment before writing any data segments. This leaves a window where the LSO segment overwrites the stamping in one cacheline that the HCA prefetches before the rest of the cacheline is filled with the correct data segments. When the HCA processes this work request, a local protection error may result. Fix this by saving the LSO header size field off and writing it only after all data segments are written. This fix is a cleaned-up version of a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>. This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1383>. Reported-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6Linus Torvalds authored
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits) ACPI PCI hotplug: harden against panic regression ACPI: rename main.c to sleep.c dell-laptop: move to drivers/platform/x86/ from drivers/misc/ eeepc-laptop: enable Bluetooth ACPI details ACPI: fix ACPI_FADT_S4_RTC_WAKE comment kprobes: check CONFIG_FREEZER instead of CONFIG_PM PM: Fix freezer compilation if PM_SLEEP is unset thermal fixup for broken BIOS which has invalid trip points. ACPI: EC: Don't trust ECDT tables from ASUS ACPI: EC: Limit workaround for ASUS notebooks even more ACPI: thinkpad-acpi: bump up version to 0.22 ACPI: thinkpad-acpi: handle HKEY event 6030 ACPI: thinkpad-acpi: clean-up fan subdriver quirk ACPI: thinkpad-acpi: start the event hunt season ACPI: thinkpad-acpi: handle HKEY thermal and battery alarms ACPI: thinkpad-acpi: clean up hotkey_notify() ACPI: thinkpad-acpi: use killable instead of interruptible mutexes ACPI: thinkpad-acpi: add UWB radio support ACPI: thinkpad-acpi: preserve radio state across shutdown ACPI: thinkpad-acpi: resume with radios disabled ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: netxen: include ipv6.h (fixes build failure) netxen: avoid invalid iounmap
-
James Bottomley authored
ACPI hotplug panic with current git head http://lkml.org/lkml/2009/1/10/136 Rather than reverting the entire commit that causes the crash: e8c331e9 "PCI hotplug: introduce functions for ACPI slot detection" simply harden against it while the changes to the hotplug code on this particularl machine are understood. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Len Brown <len.brown@intel.com>
-
Len Brown authored
-
Len Brown authored
-
Len Brown authored
-
Len Brown authored
Signed-off-by: Len Brown <len.brown@intel.com>
-
Len Brown authored
Signed-off-by: Len Brown <len.brown@intel.com>
-
Jonathan McDowell authored
Although rfkill support for the EEE bluetooth device has been added to 2.6.28-rc the appropriate ACPI accessor definitions were not added, so the support was non functional. The patch below adds the get and set accessors and has been verified to work on an EEE 901. Signed-off-by: Jonathan McDowell <noodles@earth.li> Acked-by: Matthew Garrett <mjg@redhat.com> Acked-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Len Brown <len.brown@intel.com>
-
David Brownell authored
Make the comment for ACPI_FADT_S4_RTC_WAKE match the ACPI spec; that bit has nothing to do with status bits. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
-
Masami Hiramatsu authored
Check CONFIG_FREEZER instead of CONFIG_PM because kprobe booster depends on freeze_processes() and thaw_processes() when CONFIG_PREEMPT=y. This fixes a linkage error which occurs when CONFIG_PREEMPT=y, CONFIG_PM=y and CONFIG_FREEZER=n. Reported-by: Cheng Renquan <crquan@gmail.com> Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Len Brown <len.brown@intel.com>
-
Rafael J. Wysocki authored
Freezer fails to compile if with the following configuration settings: CONFIG_CGROUPS=y CONFIG_CGROUP_FREEZER=y CONFIG_MODULES=y CONFIG_FREEZER=y CONFIG_PM=y CONFIG_PM_SLEEP=n Fix this by making process.o compilation depend on CONFIG_FREEZER. Reported-by: Cheng Renquan <crquan@gmail.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Len Brown <len.brown@intel.com>
-
Zhang Rui authored
ACPI thermal driver only re-evaluate VALID trip points. For the broken BIOS show in http://bugzilla.kernel.org/show_bug.cgi?id=8544 the active[0] is set to invalid at boot time and it will not be re-evaluated again. We can still get a single warning message at boot time. http://marc.info/?l=linux-kernel&m=120496222629983&w=2 http://bugzilla.kernel.org/show_bug.cgi?id=12203 Signed-off-by: Zhang Rui<rui.zhang@intel.com> Tested-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Len Brown <len.brown@intel.com>
-
Dhananjay Phadke authored
Fixes a build error in absence of CONFIG_IPV6: drivers/net/netxen/netxen_nic_main.c:1189: error: implicit declaration of function 'ipv6_hdr' drivers/net/netxen/netxen_nic_main.c:1189: error: invalid type argument of '->' Reported-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexey Starikovskiy authored
http://bugzilla.kernel.org/show_bug.cgi?id=9399 http://bugzilla.kernel.org/show_bug.cgi?id=11880Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
-
Dhananjay Phadke authored
For NX3031 only one I/O range is mapped, so unmapping other two which are used by older chips, causes this warning on ppc64. "Attempt to iounmap early bolted mapping at 0x0000000000000000" Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexey Starikovskiy authored
References: http://bugzilla.kernel.org/show_bug.cgi?id=11884Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstableLinus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: Btrfs: fix ioctl arg size (userland incompatible change!) Btrfs: Clear the device->running_pending flag before bailing on congestion
-
Chris Mason authored
The structure used to send device in btrfs ioctl calls was not properly aligned, and so 32 bit ioctls would not work properly on 64 bit kernels. We could fix this with compat ioctls, but we're just one byte away and it doesn't make sense at this stage to carry about the compat ioctls forever at this stage in the project. This patch brings the ioctl arg up to an evenly aligned 4k. Signed-off-by: Chris Mason <chris.mason@oracle.com>
-
Chris Mason authored
Btrfs maintains a queue of async bio submissions so the checksumming threads don't have to wait on get_request_wait. In order to avoid extra wakeups, this code has a running_pending flag that is used to tell new submissions they don't need to wake the thread. When the threads notice congestion on a single device, they may decide to requeue the job and move on to other devices. This makes sure the running_pending flag is cleared before the job is requeued. It should help avoid IO stalls by making sure the task is woken up when new submissions come in. Signed-off-by: Chris Mason <chris.mason@oracle.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpcLinus Torvalds authored
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: serial: Add 16850 uart type support to OF uart driver hvc_console: Remove tty->low_latency powerpc: Get the number of SLBs from "slb-size" property powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices powerpc/ps3: printing fixups for l64 to ll64 conversion drivers/video powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/scsi powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/ps3 powerpc/ps3: Printing fixups for l64 to ll64 conversion sound/ppc powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/char powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/block powerpc/ps3: Printing fixups for l64 to ll64 conversion arch/powerpc powerpc/ps3: ps3_repository_read_mm_info() takes u64 * arguments powerpc/ps3: clear_bit()/set_bit() operate on unsigned longs powerpc/ps3: The lv1_ routines have u64 parameters powerpc/ps3: Use dma_addr_t down through the stack powerpc/ps3: set_dabr() takes an unsigned long powerpc: Cleanup from l64 to ll64 change drivers/scsi
-
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-devLinus Torvalds authored
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: sata_fsl: Return non-zero on error in probe() drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha build libata: New driver for OCTEON SOC Compact Flash interface (v7). libata: Add another column to the ata_timing table. sata_via: Add VT8261 support pata_atiixp: update port enabledness test handling [libata] get-identity ioctl: Fix use of invalid memory pointer
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: [SCSI] Skip deleted devices in __scsi_device_lookup_by_target() [SCSI] Add SUN Universal Xport to no attach blacklist [SCSI] iscsi_tcp: make padbuf non-static [SCSI] mpt fusion: Add Firmware debug support [SCSI] mpt fusion: Add separate msi enable disable for FC,SPI,SAS [SCSI] mpt fusion: Update MPI Headers to version 01.05.19 [SCSI] qla2xxx: Fix ISP restart bug in multiq code
-
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6Linus Torvalds authored
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm/i915: lock correct mutex around object unreference. drm/i915: add support for physical memory objects drm/i915: make LVDS fixed mode a preferred mode drm: handle depth & bpp changes correctly drm: initial KMS config fixes drm/i915: setup sarea properly in master_priv drm/i915: set vblank enabled flag correctly across IRQ install/uninstall drm/i915: don't enable vblanks on disabled pipes
-