Convert paride drivers from ->media_changed() to ->check_events().

pcd and pd buffer and clear events after reporting; however, pf
unconditionally reports MEDIA_CHANGE and will generate spurious events
when polled.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Tim Waugh <tim@cyberelk.net>

Convert gdrom and viocd from ->media_changed() to ->check_events().

It's unclear how the conditions are cleared and it's possible that it
may generate spurious events when polled.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>

Convert the floppy drivers from ->media_changed() to ->check_events().
Both floppy and ataflop buffer media changed state bit and clear them
on revalidation and will behave correctly with kernel event polling.

I can't tell how amiflop clears its event and it's possible that it
may generate spurious events when polled.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>

Convert ->media_changed() to the new ->check_events() method.  The
conversion is mostly mechanical.  The only notable change is that
cdrom now doesn't generate any event if @slot_nr isn't CDSL_CURRENT.
It used to return -EINVAL which would be treated as media changed.  As
media changer isn't supported anyway, this doesn't make any
difference.

This makes ide emit the standard disk events and allows kernel event
polling.  Currently, only MEDIA_CHANGE event is implemented.  Adding
support for EJECT_REQUEST shouldn't be difficult; however, given that
ide driver is already deprecated, it probably is best to leave it
alone.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-ide@vger.kernel.org

Not all block drivers clear events immediately after reporting.  Some
do so in ->revalidate_disk() or other steps during ->open().  There is
a slim chance event poll may happen between the clearing event check
from check_disk_change() and the actual clearing of the events which
would result in spurious events.

Block event checks while block device open is in progress.  There is
no need to kick explicit event check afterwards as events are always
checked during open.

-v2: The original patch could have called disk_unblock_events() with
     an already released or %NULL @disk causing oops.  Fixed by making
     sure references are put after disk_unblock_events() is called.
     It also makes the error path of __blkdev_get() a bit simpler.
     This problem was reported by Jens.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>

The block event mechanism currently always checks events when the
device is being closed regardless of the open mode.  The intention was
to allow detection of EJECT_REQUEST when a device is closed whether
disk event polling is enabled or not.

This is unnecessary as, for devices of interest, events are checked
from either userland or kernel and in the former case ->check_events()
is performed on open of each poll attempt anyway.  Furthermore, this
unconditional event check on close makes the code susceptible to event
loop if the block driver doesn't clear reported events correctly - an
event triggers userland to open and close the device which in turn
causes another event, rinse and repeat.

Check events on close only if it was blocked by excl write open.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>

Currently, disk_unblock_events() implicitly kick event check if the
block count reaches zero.  This behavior is not described in the
comment and hinders with future changes.  Make the unblocker
explicitly check events by calling disk_check_events() as necessary.

This patch doesn't cause any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>

We've found that we still get good, useful isolation at weights this
low. I'd like to adjust the minimum so that any other changes can take
these values into account.
Signed-off-by: Justin TerAvest <teravest@google.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

The block integrity subsystem no longer uses the bio_vec slabs so this
code can safely be compiled in.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

When throttle group limits are updated through cgroups, a thread is
woken up to process these updates. While reviewing that code, oleg noted
couple of race conditions existed in the code and he also suggested that
code can be simplified.

This patch fixes the races simplifies the code based on Oleg's suggestions:

	- Use xchg().
	- Introduced a common function throtl_update_blkio_group_common()
          which is shared now by all iops/bps update functions.
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>

Fixed a merge issue, throtl_schedule_delayed_work() takes throtl_data
as the argument now, not the queue.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

With the help of cgroup interface one can go and upate the bps/iops
limits of existing group. Once the limits are udpated, a thread is
woken up to see if some blocked group needs recalculation based on new
limits and needs to be requeued.

There was also a piece of code where I was checking for group limit
update when a fresh bio comes in. This patch gets rid of that piece of
code and keeps processing the limit change at one place
throtl_process_limit_change().  It just keeps the code simple and easy
to understand.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

Merge branch 'block-for-2.6.39-core' of ssh://master.kernel.org/pub/scm/linux/kernel/git/tj/misc into for-2.6.39/core

The update_vdisktime logic is broken since commit
b54ce60e, st->min_vdisktime never makes
a progress. Fix it.

Thanks Vivek for pointing it out.
Signed-off-by: Gui Jianfeng <guijianfen@cn.fujitsu.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

If there are a sync and an async queue and the sync queue's think time
is small, we can ignore the sync queue's dispatch quantum. Because the
sync queue will always preempt the async queue, we don't need to care
about async's latency.  This can fix a performance regression of
aiostress test, which is introduced by commit f8ae6e3e. The issue
should exist even without the commit, but the commit amplifies the
impact.

The initial post does the same optimization for RT queue too, but since
I have no real workload for it, Vivek suggests to drop it.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Reviewed-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

We need to hold the queue lock over the reference increment,
it's not atomic anymore.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

This merge creates two set of conflicts.  One is simple context
conflicts caused by removal of throtl_scheduled_delayed_work() in
for-linus and removal of throtl_shutdown_timer_wq() in
for-2.6.39/core.

The other is caused by commit 255bb490 (block: blk-flush shouldn't
call directly into q->request_fn() __blk_run_queue()) in for-linus
crashing with FLUSH reimplementation in for-2.6.39/core.  The conflict
isn't trivial but the resolution is straight-forward.

* __blk_run_queue() calls in flush_end_io() and flush_data_end_io()
  should be called with @force_kblockd set to %true.

* elv_insert() in blk_kick_flush() should use
  %ELEVATOR_INSERT_REQUEUE.

Both changes are to avoid invoking ->request_fn() directly from
request completion path and closely match the changes in the commit
255bb490.
Signed-off-by: Tejun Heo <tj@kernel.org>

Following steps lead to deadlock in kernel:

dd if=/dev/zero of=img bs=512 count=1000
losetup -f img
mkfs.ext2 /dev/loop0
mount -t ext2 -o loop /dev/loop0 mnt
umount mnt/

Stacktrace:
[<c102ec04>] irq_exit+0x36/0x59
[<c101502c>] smp_apic_timer_interrupt+0x6b/0x75
[<c127f639>] apic_timer_interrupt+0x31/0x38
[<c101df88>] mutex_spin_on_owner+0x54/0x5b
[<fe2250e9>] lo_release+0x12/0x67 [loop]
[<c10c4eae>] __blkdev_put+0x7c/0x10c
[<c10a4da5>] fput+0xd5/0x1aa
[<fe2250cf>] loop_clr_fd+0x1a9/0x1b1 [loop]
[<fe225110>] lo_release+0x39/0x67 [loop]
[<c10c4eae>] __blkdev_put+0x7c/0x10c
[<c10a59d9>] deactivate_locked_super+0x17/0x36
[<c10b6f37>] sys_umount+0x27e/0x2a5
[<c10b6f69>] sys_oldumount+0xb/0xe
[<c1002897>] sysenter_do_call+0x12/0x26
[<ffffffff>] 0xffffffff

Regression since 2a48fc0a, which introduced the private
loop_mutex as part of the BKL removal process.

As per [1], the mutex can be safely removed.

[1] http://www.gossamer-threads.com/lists/linux/kernel/1341930

Addresses: https://bugzilla.novell.com/show_bug.cgi?id=669394
Addresses: https://bugzilla.kernel.org/show_bug.cgi?id=29172Signed-off-by: Petr Uzel <petr.uzel@suse.cz>
Cc: stable@kernel.org
Reviewed-by: Nikanth Karthikesan <knikanth@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

If we enable trace events to trace block actions, We use
blk_fill_rwbs_rq to analyze the corresponding actions
in request's cmd_flags, but we only choose the minor 2 bits
from it, so most of other flags(e.g, REQ_SYNC) are missing.
For example, with a sync write we get:
write_test-2409  [001]   160.013869: block_rq_insert: 3,64 W 0 () 258135 + =
8 [write_test]

Since now we have integrated the flags of both bio and request,
it is safe to pass rq->cmd_flags directly to blk_fill_rwbs and
blk_fill_rwbs_rq isn't needed any more.

With this patch, after a sync write we get:
write_test-2417  [000]   226.603878: block_rq_insert: 3,64 WS 0 () 258135 +=
 8 [write_test]
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

Move blk_throtl_exit() in blk_cleanup_queue() as blk_throtl_exit() is
written in such a way that it needs queue lock. In blk_release_queue()
there is no gurantee that ->queue_lock is still around.

Initially blk_throtl_exit() was in blk_cleanup_queue() but Ingo reported
one problem.

  https://lkml.org/lkml/2010/10/23/86

  And a quick fix moved blk_throtl_exit() to blk_release_queue().

        commit 7ad58c02
        Author: Jens Axboe <jaxboe@fusionio.com>
        Date:   Sat Oct 23 20:40:26 2010 +0200

        block: fix use-after-free bug in blk throttle code

This patch reverts above change and does not try to shutdown the
throtl work in blk_sync_queue(). By avoiding call to
throtl_shutdown_timer_wq() from blk_sync_queue(), we should also avoid
the problem reported by Ingo.

blk_sync_queue() seems to be used only by md driver and it seems to be
using it to make sure q->unplug_fn is not called as md registers its
own unplug functions and it is about to free up the data structures
used by unplug_fn(). Block throttle does not call back into unplug_fn()
or into md. So there is no need to cancel blk throttle work.

In fact I think cancelling block throttle work is bad because it might
happen that some bios are throttled and scheduled to be dispatched later
with the help of pending work and if work is cancelled, these bios might
never be dispatched.

Block layer also uses blk_sync_queue() during blk_cleanup_queue() and
blk_release_queue() time. That should be safe as we are also calling
blk_throtl_exit() which should make sure all the throttling related
data structures are cleaned up.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

Now we initialize ->queue_lock at queue allocation time so driver does
not have to worry about initializing it before calling
blk_cleanup_queue().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

There does not seem to be a clear convention whether q->queue_lock is
initialized or not when blk_cleanup_queue() is called. In the past it
was not necessary but now blk_throtl_exit() takes up queue lock by
default and needs queue lock to be available.

In fact elevator_exit() code also has similar requirement just that it
is less stringent in the sense that elevator_exit() is called only if
elevator is initialized.

Two problems have been noticed because of ambiguity about spin lock
status.

      - If a driver calls blk_alloc_queue() and then soon calls
        blk_cleanup_queue() almost immediately, (because some other
	driver structure allocation failed or some other error happened)
	then blk_throtl_exit() will run into issues as queue lock is not
	initialized. Loop driver ran into this issue recently and I
	noticed error paths in md driver too. Similar error paths should
	exist in other drivers too.

      - If some driver provided external spin lock and zapped the lock
        before blk_cleanup_queue(), then it can lead to issues.

So this patch initializes the default queue lock at queue allocation time.

block throttling code is one of the users of queue lock and it is
initialized at the queue allocation time, so it makes sense to
initialize ->queue_lock also to internal lock. A driver can overide that
lock later. This will take care of the issue where a driver does not have
to worry about initializing the queue lock to default before calling
blk_cleanup_queue()
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

Rename the numerals in the diskstats_show() into the macros.

Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

blk-flush decomposes a flush into sequence of multiple requests.  On
completion of a request, the next one is queued; however, block layer
must not implicitly call into q->request_fn() directly from completion
path.  This makes the queue behave unexpectedly when seen from the
drivers and violates the assumption that q->request_fn() is called
with process context + queue_lock.

This patch makes blk-flush the following two changes to make sure
q->request_fn() is not called directly from request completion path.

- blk_flush_complete_seq_end_io() now asks __blk_run_queue() to always
  use kblockd instead of calling directly into q->request_fn().

- queue_next_fseq() uses ELEVATOR_INSERT_REQUEUE instead of
  ELEVATOR_INSERT_FRONT so that elv_insert() doesn't try to unplug the
  request queue directly.

Reported by Jan in the following threads.

 http://thread.gmane.org/gmane.linux.ide/48778
 http://thread.gmane.org/gmane.linux.ide/48786

stable: applicable to v2.6.37.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jan Beulich <JBeulich@novell.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

__blk_run_queue() automatically either calls q->request_fn() directly
or schedules kblockd depending on whether the function is recursed.
blk-flush implementation needs to be able to explicitly choose
kblockd.  Add @force_kblockd.

All the current users are converted to specify %false for the
parameter and this patch doesn't introduce any behavior change.

stable: This is prerequisite for fixing ide oops caused by the new
        blk-flush implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

Effectively, make group_isolation=1 the default and remove the tunable.
The setting group_isolation=0 was because by default we idle on
sync-noidle tree and on fast devices, this can be very harmful for
throughput.

However, this problem can also be addressed by tuning slice_idle and
possibly group_idle on faster storage devices.

This change simplifies the CFQ code by removing the feature entirely.
Signed-off-by: Justin TerAvest <teravest@google.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

Conflicts:
	block/cfq-iosched.c
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

o Dominik Klein reported a system hang issue while doing some blkio
  throttling testing.

  https://lkml.org/lkml/2011/2/24/173

o Some tracing revealed that CFQ was not dispatching any more jobs as
  queue unplug was not happening. And queue unplug was not happening
  because unplug work was not being called as there was one throttling
  work on same cpu which as not finished yet. And throttling work had not
  finished as it was tyring to dispatch a bio to CFQ but all the request
  descriptors were consume to it was put to sleep.

o So basically it is a cyclic dependecny between CFQ unplug work and
  throtl dispatch work. Tejun suggested that use separate workqueue for
  such cases.

o This patch uses a separate workqueue for throttle related work and
  does not rely on kblockd workqueue anymore.

Cc: stable@kernel.org
Reported-by: Dominik Klein <dk@in-telegence.net>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (adt7411) add MODULE_DEVICE_TABLE
  hwmon: (ad7414) add MODULE_DEVICE_TABLE

Fix new kernel-doc warning in fs/block_dev.c:

Warning(fs/block_dev.c:937): No description found for parameter 'kill_dirty'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Several ACPI drivers fail to build if CONFIG_NET is unset, because
they refer to things depending on CONFIG_THERMAL that in turn depends
on CONFIG_NET.  However, CONFIG_THERMAL doesn't really need to depend
on CONFIG_NET, because the only part of it requiring CONFIG_NET is
the netlink interface in thermal_sys.c.

Put the netlink interface in thermal_sys.c under #ifdef CONFIG_NET
and remove the dependency of CONFIG_THERMAL on CONFIG_NET from
drivers/thermal/Kconfig.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Len Brown <lenb@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Luming Yu <luming.yu@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm: fix unsigned vs signed comparison issue in modeset ctl ioctl.
  drm/nv50-nvc0: make sure vma is definitely unmapped when destroying bo

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  omap4: prcm: Fix the CPUx clockdomain offsets
  OMAP2+: clocksource: fix crash on boot when !CONFIG_OMAP_32K_TIMER
  OMAP2/3: clock: fix fint calculation for DPLL_FREQSEL
  OMAP2+: mailbox: fix lookups for multiple mailboxes
  OMAP2420: mailbox: fix IVA vs DSP IRQ numbering
  mach-omap2: smartreflex: world-writable debugfs voltage files
  mach-omap2: pm: world-writable debugfs timer files
  mach-omap2: mux: world-writable debugfs files

Merge branches 'perf-fixes-for-linus', 'x86-fixes-for-linus' and 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf timechart: Fix max number of cpus
  perf timechart: Fix black idle boxes in the title
  perf hists: Print number of samples, not the period sum

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Use u32 instead of long to set reset vector back to 0

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clockevents: Prevent oneshot mode when broadcast device is periodic

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: fix truncate after open
  fuse: fix hang of single threaded fuseblk filesystem

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  ocfs2: Check heartbeat mode for kernel stacks only
  Ocfs2/refcounttree: Fix a bug for refcounttree to writeback clusters in a right number.
  ocfs2: Fix estimate of necessary credits for mkdir

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  eukrea-tlv320: fix platform_name
  ASoC: correct pxa AC97 DAI names
  ALSA: hda - Add support for new IDT 92HD98 and 92HD99 codecs
  ALSA: HDA: Add ideapad quirk for two Dell machines
  ALSA: HDA: Add a new Conexant codec 506e (20590)
  ALSA: usb-audio: fix oops due to cleanup race when disconnecting
  ASoC: Hook wm_hubs micbiases up to CLK_SYS
  ASoC: Correct definition of WM8903_VMID_RES_5K
  ASoC: Fix WM8958 default microphone detection argument ordering
  ALSA: HDA: Fix mic initialization in VIA auto parser
  ALSA: fix one memory leak in sound jack

Commit e2cda322 ("thp: add pmd mangling generic functions") replaced
some macros in <asm-generic/pgtable.h> with inline functions.

If the functions are to be defined (not all architectures need them)
then struct vm_area_struct must be defined first.  So include
<linux/mm_types.h>.

Fixes a build failure seen in Debian:

    CC [M]  drivers/media/dvb/mantis/mantis_pci.o
  In file included from arch/arm/include/asm/pgtable.h:460,
                   from drivers/media/dvb/mantis/mantis_pci.c:25:
  include/asm-generic/pgtable.h: In function 'ptep_test_and_clear_young':
  include/asm-generic/pgtable.h:29: error: dereferencing pointer to incomplete type
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A customer of ours, complained that when setting the reset
vector back to 0, it trashed other data and hung their box.
They noticed when only 4 bytes were set to 0 instead of 8,
everything worked correctly.

Mathew pointed out:

 |
 | We're supposed to be resetting trampoline_phys_low and
 | trampoline_phys_high here, which are two 16-bit values.
 | Writing 64 bits is definitely going to overwrite space
 | that we're not supposed to be touching.
 |

So limit the area modified to u32.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: <stable@kernel.org>
LKML-Reference: <1297139100-424-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Currently numcpus is determined in pid_put_sample which is only
called on sched_switch/sched_wakeup sample processing.

On a machine with a lot cpus I often saw the last cpu missing.

Check for (max) numcpus on every event happening and in the
beginning. -> fixes the issue for me.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: lenb@kernel.org
LKML-Reference: <1298842606-55712-6-git-send-email-trenn@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>