- 20 Dec, 2018 24 commits
-
-
Mahesh Rajashekhara authored
Reviewed-by:
Scott Benesh <scott.benesh@microsemi.com> Reviewed-by:
Ajish Koshy <ajish.koshy@microsemi.com> Reviewed-by:
Murthy Bhat <murthy.bhat@microsemi.com> Reviewed-by:
Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com> Reviewed-by:
Dave Carroll <david.carroll@microsemi.com> Reviewed-by:
Scott Teel <scott.teel@microsemi.com> Reviewed-by:
Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by:
Don Brace <don.brace@microsemi.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Dave Carroll authored
During slave_alloc, for logical volumes include no_write_same into the scsi_device structure. This will insure that WRITE_SAME will not be used for LD's. Reviewed-by:
Justin Lindley <justin.lindley@microsemi.com> Reviewed-by:
-
Mahesh Rajashekhara authored
Reviewed-by:
-
Kevin Barnett authored
Add support for new IUs and parsing of the Firmware Features section of the PQI Config Table to implement the "handshake" between the driver and firmware to communicate firmware features supported and enabled by the driver. Reviewed-by:
-
James Smart authored
Update lpfc version to 12.0.0.10 Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Signed-off-by:
-
James Smart authored
This patch adds a "pci_bus_reset" option to the board_mode sysfs attribute. This option uses the pci_reset_bus() api to reset the PCIe link the adapter is on, which will reset the chip/adapter. Prior to issuing this option, all functions on the same chip must be placed in the offline state by the admin. After the reset, all of the instances may be brought online again. The primary purpose of this functionality is to support cases where firmware update required a chip reset but the admin did not want to reboot the machine in order to instantiate the firmware update. Sanity checks take place prior to the reset to ensure the adapter is the sole entity on the PCIe bus and that all functions are in the offline state. Signed-off-by:
-
James Smart authored
Current messages report generic actions (like send GID_FT), but misses reporting for what protocol type the action is taken. Revise the messages to reflect the FC4 protocol type being worked on. [mkp: typo] Signed-off-by:
-
James Smart authored
When a target's link dropped, an RSCN was received to communicate the change. The driver detected the loss of the target and issued and UNREG_RPI mailbox command. While that was being processed, another RSCN was received to communicate the port coming back. The driver deferred the PLOGI to the port until the mailbox command finishes. When the mailbox command completed it saw the pending port and called the routines to issue the PLOGI. However, it forgot to clear the UNREG_INP state flag, so the PLOGI xmt routine nooped the PLOGI request assuming it needed to wait for the mailbox command. At this point, login would never be re-attempted. Clear UNREG_INP before issuing the deferred PLOGI. Signed-off-by:
-
James Smart authored
Currently, when a trunk link goes down due to some fault, the driver snapshots the fault code. If the link then comes back up, meaning there is no fault, the driver is not clearing the fault code so the sysfs link_state entry reports old/stale data. Revise the logic so that on successful link up the fault code is cleared. Signed-off-by:
-
James Smart authored
The existing MDS loopback diagnostics support processing received frames in the slowpath work thread. It caps the number of frames it will process at 64, before waiting for another event to indicate additional frame reception. The net-net is this results in very slow frame processing during loopback tests and sometimes orphans an io, causing the loopback test to report failure by the switch. Move MDS loopback frame processing out of the slow path worker thread and into the normal RQ processing routines. Signed-off-by:
-
James Smart authored
If the adapter is taken offline, the trunk link port attributes continue to report trunk links as up even though all links are down as the adapter is offline. Clear the trunk links state as part of taking the adapter offline. Signed-off-by:
-
Colin Ian King authored
There is a break statement with an extra space that needs removed and a call to bfa_trc that is indented one level too much. Fix these. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Colin Ian King authored
There is a tab missing on a return statement, add the missing tab. Signed-off-by:
-
Varun Prakash authored
In case of ->vport_create() call scsi_add_host_with_dma() instead of scsi_add_host() to pass correct dma device. Signed-off-by:
Varun Prakash <varun@chelsio.com> Signed-off-by:
-
Christoph Hellwig authored
The old DAC960 driver was fine with merging over segment boundaries, so this new driver should be too. [mkp: typos] Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Christoph Hellwig authored
The old DAC960 driver was fine with merging over segment boundaries, so this new driver should be too. [mkp: typos] Signed-off-by:
-
Shivasharan S authored
Signed-off-by:
Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by:
-
Shivasharan S authored
Although MegaRAID controllers support 64-bit DMA addressing, as per hardware design, DMA address with all 64-bits set (0xFFFFFFFF-FFFFFFFF) results in a firmware fault. Driver will set 63-bit DMA mask to ensure the above address will not be used. Cc: stable@vger.kernel.org Signed-off-by:
-
Shivasharan S authored
Due to hardware errata in Aero controllers, reads to certain fusion registers could intermittently return zero. This behavior is transient in nature and subsequent reads will return valid value. For Aero controllers, any calls to readl to read from certain registers will be retried for maximum three times, if read returns zero. Signed-off-by:
-
Shivasharan S authored
Instead of the register address, pass the instance pointer to clear_intr and read_fw_status_reg functions. This is done in preparation for adding adapter type based checks in these functions in later patches of this series. Signed-off-by:
-
Shivasharan S authored
Identify all Aero controller PCI IDs with new adapter type. Signed-off-by:
-
Shivasharan S authored
In preparation for the new Aero series adapter type, all the places where we check adapter type for Ventura series needs to include any later adapter types. Signed-off-by:
-
Stephan Günther authored
With commit 09c2f95a ("scsi: mpt3sas: Swap I/O memory read value back to cpu endianness"), 64bit writes in _base_writeq() were rewritten to use __raw_writeq() instad of writeq(). This introduced a bug apparent on powerpc64 systems such as the Raptor Talos II that causes the HBA to drop from the PCIe bus under heavy load and being reinitialized after a couple of seconds. It can easily be triggered on affacted systems by using something like fio --name=random-write --iodepth=4 --rw=randwrite --bs=4k --direct=0 \ --size=128M --numjobs=64 --end_fsync=1 fio --name=random-write --iodepth=4 --rw=randwrite --bs=64k --direct=0 \ --size=128M --numjobs=64 --end_fsync=1 a couple of times. In my case I tested it on both a ZFS raidz2 and a btrfs raid6 using LSI 9300-8i and 9400-8i controllers. The fix consists in resembling the write ordering of writeq() by adding a mandatory write memory barrier before device access and a compiler barrier afterwards. The additional MMIO barrier is superfluous. Signed-off-by:
Stephan Günther <moepi@moepi.net> Reported-by:
Matt Corallo <linux@bluematt.me> Acked-by:
Sreekanth Reddy <Sreekanth.Reddy@broadcom.com> Signed-off-by:
-
Anatoliy Glagolev authored
The intent of invoking configfs_depend_item in commit 7474f52a ("tcm_qla2xxx: Perform configfs depend/undepend for base_tpg") was to prevent a physical Fibre Channel port removal when virtual (NPIV) ports announced through that physical port are active. The change does not work as expected: it makes enabled physical port dependent on target configfs subsystem (the port's parent), something the configfs guarantees anyway. Besides, scheduling work in a worker thread and waiting for the work's completion is not really a valid workaround for the requirement not to call configfs_depend_item from a configfs callback: the call occasionally deadlocks. Thus, removing configfs_depend_item calls does not break anything and fixes the deadlock problem. Signed-off-by:
Anatoliy Glagolev <glagolig@gmail.com> Acked-by:
Himanshu Madhani <hmadhani@marvell.com> Signed-off-by:
-
- 19 Dec, 2018 14 commits
-
-
Christoph Hellwig authored
Now that the the SCSI layer replaced the use of the cluster flag with segment size limits and the DMA boundary we can remove the cluster flag from the block layer. Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Xiang Chen authored
For v3 hw, we support DIF operation for SAS, but not SATA. In addition, DIF CRC16 is supported. This patchset adds the SW support for the described features. The main components are as follows: - Get protection mask from module param - Fill PI fields - Fill related to DIF in DQ and protection iu memories Signed-off-by:
Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by:
John Garry <john.garry@huawei.com> Signed-off-by:
-
Ewan D. Milne authored
Certain older adapters such as the OneConnect OCe10100 may not have a valid wqpcnt value. In this case, do not set queue->page_count to 0 in lpfc_sli4_queue_alloc() as this will prevent the driver from initializing. Fixes: 895427bd ("scsi: lpfc: NVME Initiator: Base modifications") Cc: stable@vger.kernel.org # 4.11+ Signed-off-by:
Ewan D. Milne <emilne@redhat.com> Reviewed-by:
Laurence Oberman <loberman@redhat.com> Tested-by:
-
Christoph Hellwig authored
The same effects can be achieved by setting the dma_boundary to PAGE_SIZE - 1 and the max_segment_size to PAGE_SIZE, so shift those settings into the drivers. Note that in many cases the setting might be bogus, but this keeps the status quo. [mkp: fix myrs and myrb] Signed-off-by:
-
Christoph Hellwig authored
mac53c94 has no limitations on crossing pages for segments. Just make the 65535 byte segment size limit explicit, even if it matches the current block layer limit. Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
-
Christoph Hellwig authored
mesh has no limitations on crossing pages for segments. Just make the 65535 byte segment size limit explicit, even if it matches the current block layer limit. Signed-off-by:
-
Christoph Hellwig authored
There is no such limitation in the protocol or implementation, so remove it. Signed-off-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
-
Christoph Hellwig authored
This driver already sets the dma_boundary to PAGE_SIZE - 1, which has the same result. Signed-off-by:
-
Christoph Hellwig authored
This driver already sets the dma_boundary to PAGE_SIZE - 1, which has the same result. Signed-off-by:
-
Christoph Hellwig authored
This allows the host driver to indicate the maximum supported segment size in a nice an easy way, so that the driver doesn't have to worry about DMA-layer imposed limitations. Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
-
Christoph Hellwig authored
Most SCSI drivers want to enable "clustering", that is merging of segments so that they might span more than a single page. Remove the ENABLE_CLUSTERING define, and require drivers to explicitly set DISABLE_CLUSTERING to disable this feature. Signed-off-by:
-
Christoph Hellwig authored
A few drivers were not setting the use_clustering flag at all and thus default to disable. Fix them up to explicitly set this field in preparation for additional cleanups. Signed-off-by:
-
Wei Yongjun authored
memory allocated by kmem_cache_alloc() should be freed using kmem_cache_free(), not kfree(). Fixes: ad669505 ("scsi: target/core: Make sure that target_wait_for_sess_cmds() waits long enough") Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by:
-
Bart Van Assche authored
Commit b5b6e8c8 ("scsi: virtio_scsi: fix IO hang caused by automatic irq vector affinity") removed all virtio_scsi hostdata users. Since the SCSI host data is no longer used, also remove the host data itself. Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ming Lei <ming.lei@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by:
Ming Lei <ming.lei@redhat.com> Signed-off-by:
-
- 13 Dec, 2018 2 commits
-
-
YueHaibing authored
Remove .owner field if calls are used which set it automatically Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Suganath Prabu authored
Update driver version from 27.100.00.00 to 27.101.00.00. Signed-off-by:
Suganath Prabu <suganath-prabu.subramani@broadcom.com> Signed-off-by:
-
