This patch creates a new event class called xhci_log_ring, and
defines the events used for tracing the change of all kinds of
rings used by an xhci host. An xHCI ring is basically a memory
block shared between software and hardware. By tracing changes
of rings, it makes the life easier for debugging hardware or
software problems.

This info can be used, later, to print, in a human readable way,
the life cycle of an xHCI ring using the trace-cmd tool and the
appropriate plugin.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce a new xhci_hc_died() function that takes care of handling
pending commands and URBs if a host controller becomes unresponsive.

This addresses issues on hotpluggable xhci controllers that disappear
from the bus suddenly, often while the bus (PCI) remove function is
still being processed.

xhci_hc_died() sets a XHCI_STATUS_DYING flag to prevent new URBs and
commands or to be queued. The flag also ensures xhci_hc_died() will
give back pending commands and URBs once.

Host is considered dead if register read returns 0xffffffff, or host
fails to abort the command ring, or fails stopping an endpoint after
trying for 5 seconds.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We can't halt the host controller immediately when first HCD is removed as
it will cause problems if we have devices attached to the second (primary)
HCD, like a keyboard.

We've been carrying this in our Linux-as-a-bootloader environment for a
little while now. The machines all have the same TI TUSB73x0 part,
and when we kexec the devices don't come back until a system power cycle.

[minor adjustments, code comments and remove HALT check  -Mathias]
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There's one annoyance in how xhci prints debug messages, we often
get logs with messages but it's hard to say from which device and
endpoint the message originates. Add slot_id, ep_index messages
in handle_tx_event.
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Format for each TRB in each control transfer stage differs. Let's make
sure we correctly pretty print these fields to avoid confusion.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With these, we can track what's happening with the HW while executing
each and every command. It will give us visibility into how the
different contexts are being modified by xHC which can bring insight
into problems while debugging.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

By extracting and exposing xhci_slot_state_string() in a header file, we
can re-use it to print Slot Context State from our tracepoints, which
can aid in tracking down problems related to command execution.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This will help us figuring out which device $this URB belongs to while
debugging.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For usb2 ports, the port test mode Test_J_State, Test_K_State,
Test_Packet, Test_SE0_NAK and Test_Force_En can be enabled
as described in usb2 spec.

USB2 test mode is a required hardware feature for system integrators
validating their hardware according to USB spec, regarding signal
strength and stuff. It is purely a hardware test feature.

Usually you need an oscilloscope and have to enable those test modes on
the hardware. This will send some specific test patterns on D+/D-. There
is no report available (in Linux itself) as it is purely externally
visible. Regular USB usage is not possible at that time.
Anyone (well access to e.g. /dev/bus/usb/001/001 provided) can use it by
sending appropriate USB_PORT_FEAT_TEST requests to the hub.

[Add better commit message by Alexander Stein  -Mathias]
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change the visability of xhci_start() so that it
can be used when enabling test mode.
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactoring slot disable related code into a helper
function xhci_disable_slot() which can be used when
enabling test mode.
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactoring port power on/off related code into
a helper function xhci_set_power_on() which can
be reused when enabling test mode.

[set port state to neutral before writing port power -Mathias]
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

EINT(Event Interrupt) is a write-1-to-clear type of bit in xhci
status register. It should be cleared by writing a 1. Writing 0
to this bit has no effect.

Xhci driver tries to clear this bit by writing 0 to it. This is
not the right way to go. This patch corrects this by reading the
register first, then clearing all RO/RW1C/RsvZ bits and setting
the clearing bit, and writing back the new value at last.

Xhci spec requires that software that uses EINT shall clear it
prior to clearing any IP flags in section 5.4.2. This is the
reason why this patch is CC'ed stable as well.

[old way didn't cause any issues, skip stable, send to next -Mathias]

Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB host controllers can take a significant amount of time to suspend
and resume, adding several hundred miliseconds to the kernel resume
time. Since the XHCI controller has no outside dependencies (other than
clocks, which are suspended late/resumed early), allow it to suspend and
resume asynchronously.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vhci_tx_urb() should be able to get the vhci_device from
its caller vhci_urb_enqueue(), instead of brutal-force
searching it.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Code refactoring to make the flow easier to follow.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add missing continue in switch.

Addresses-Coverity-ID: 1248733
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a8c06e40 ("usb: separate out sysdev pointer from
usb_bus") converted to use hcd->self.sysdev for DMA
operations instead of hcd->self.controller but forgot to do
it for one instance.

This gets caught when DMA debugging is enabled since dma map
and unmap end up using different device pointers.

Fix it.

Fixes: a8c06e40 ("usb: separate out sysdev pointer from usb_bus")
Reported-by: Carlos Hernandez <ceh@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the usb fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull dmaengine fixes from Vinod Koul:
 "A couple of minor fixes for 4.11:

   - array bound fix for __get_unmap_pool()

   - cyclic period splitting for bcm2835"

* tag 'dmaengine-fix-4.11-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: Fix array index out of bounds warning in __get_unmap_pool()
  dmaengine: bcm2835: Fix cyclic DMA period splitting

Pull x86 fixes from Thomas Gleixner:
 "This update provides:

   - prevent KASLR from randomizing EFI regions

   - restrict the usage of -maccumulate-outgoing-args and document when
     and why it is required.

   - make the Global Physical Address calculation for UV4 systems work
     correctly.

   - address a copy->paste->forgot-edit problem in the MCE exception
     table entries.

   - assign a name to AMD MCA bank 3, so the sysfs file registration
     works.

   - add a missing include in the boot code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot: Include missing header file
  x86/mce/AMD: Give a name to MCA bank 3 when accessed with legacy MSRs
  x86/build: Mostly disable '-maccumulate-outgoing-args'
  x86/mm/KASLR: Exclude EFI region from KASLR VA space randomization
  x86/mce: Fix copy/paste error in exception table entries
  x86/platform/uv: Fix calculation of Global Physical Address

Pull scheduler fixes from Thomas Gleixner:
 "This update provides:

   - make the scheduler clock switch to unstable mode smooth so the
     timestamps stay at microseconds granularity instead of switching to
     tick granularity.

   - unbreak perf test tsc by taking the new offset into account which
     was added in order to proveide better sched clock continuity

   - switching sched clock to unstable mode runs all clock related
     computations which affect the sched clock output itself from a work
     queue. In case of preemption sched clock uses half updated data and
     provides wrong timestamps. Keep the math in the protected context
     and delegate only the static key switch to workqueue context.

   - remove a duplicate header include"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/headers: Remove duplicate #include <linux/sched/debug.h> line
  sched/clock: Fix broken stable to unstable transfer
  sched/clock, x86/perf: Fix "perf test tsc"
  sched/clock: Fix clear_sched_clock_stable() preempt wobbly

Pull EFI fix from Thomas Gleixner:
 "Downgrade the missing ESRT header printk to warning level and remove a
  useless error printk which just generates noise for no value"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/esrt: Cleanup bad memory map log messages

Pull timer fixes from Thomas Gleixner:
 "Two small fixes for the new CLKEVT_OF infrastructure"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  vmlinux.lds: Add __clkevt_of_table to kernel
  clockevents: Fix syntax error in clkevt-of macro

Pull irq fixes from Thomas Gleixner:
 "Two small fixlets:

   - select a required Kconfig to make the MVEBU driver compile

   - add the missing MIPS local GIC interrupts which prevent drivers to
     probe successfully"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/mips-gic: Fix Local compare interrupt
  irqchip/mvebu-odmi: Select GENERIC_MSI_IRQ_DOMAIN

Pull core fix from Thomas Gleixner:
 "Prevent leaking kernel memory via /proc/$pid/syscall when the queried
  task is not in a syscall"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  lib/syscall: Clear return values when no stack

Pull parisc fixes from Helge Deller:
 "Al Viro reported that - in case of read faults - our copy_from_user()
  implementation may claim to have copied more bytes than it actually
  did. In order to fix this bug and because of the way how gcc optimizes
  register usage for inline assembly in C code, we had to replace our
  pa_memcpy() function with a pure assembler implementation.

  While fixing the memcpy bug we noticed some other issues with our
  get_user() and put_user() functions, e.g. nested faults may return
  wrong data. This is now fixed by a common fixup handler for
  get_user/put_user in the exception handler which additionally makes
  generated code smaller and faster.

  The third patch is a trivial one-line fix for a patch which went in
  during 4.11-rc and which avoids stalled CPU warnings after power
  shutdown (for parisc machines which can't plug power off themselves).

  Due to the rewrite of pa_memcpy() into assembly this patch got bigger
  than what I wanted to have sent at this stage.

  Those patches have been running in production during the last few days
  on our debian build servers without any further issues"

* 'parisc-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Avoid stalled CPU warnings after system shutdown
  parisc: Clean up fixup routines for get_user()/put_user()
  parisc: Fix access fault handling in pa_memcpy()

Pull SCSI fixes from James Bottomley:
 "Thirteen small fixes: The hopefully final effort to get the lpfc nvme
  kconfig problems sorted, there's one important sg fix (user can induce
  read after end of buffer) and one minor enhancement (adding an extra
  PCI ID to qedi). The rest are a set of minor fixes, which mostly occur
  as user visible in error legs or on specific devices"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: remove the duplicated checking for supporting clkscaling
  scsi: lpfc: fix building without debugfs support
  scsi: lpfc: Fix PT2PT PRLI reject
  scsi: hpsa: fix volume offline state
  scsi: libsas: fix ata xfer length
  scsi: scsi_dh_alua: Warn if the first argument of alua_rtpg_queue() is NULL
  scsi: scsi_dh_alua: Ensure that alua_activate() calls the completion function
  scsi: scsi_dh_alua: Check scsi_device_get() return value
  scsi: sg: check length passed to SG_NEXT_CMD_LEN
  scsi: ufshcd-platform: remove the useless cast in ERR_PTR/IS_ERR
  scsi: qedi: Add PCI device-ID for QL41xxx adapters.
  scsi: aacraid: Fix potential null access
  scsi: qla2xxx: Fix crash in qla2xxx_eh_abort on bad ptr

Merge misc fixes from Andrew Morton:
 "11 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  kasan: do not sanitize kexec purgatory
  drivers/rapidio/devices/tsi721.c: make module parameter variable name unique
  mm/hugetlb.c: don't call region_abort if region_chg fails
  kasan: report only the first error by default
  hugetlbfs: initialize shared policy as part of inode allocation
  mm: fix section name for .data..ro_after_init
  mm, hugetlb: use pte_present() instead of pmd_present() in follow_huge_pmd()
  mm: workingset: fix premature shadow node shrinking with cgroups
  mm: rmap: fix huge file mmap accounting in the memcg stats
  mm: move mm_percpu_wq initialization earlier
  mm: migrate: fix remove_migration_pte() for ksm pages

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for 4.11-rc5.

  The usual xhci fixes are here, as well as a fix for yet-another-bug-
  found-by-KASAN, those developers are doing great stuff here.

  And there's a phy build warning fix that showed up in 4.11-rc1.

  All of these have been in linux-next with no reported issues"

* tag 'usb-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: phy: isp1301: Fix build warning when CONFIG_OF is disabled
  xhci: Manually give back cancelled URB if we can't queue it for cancel
  xhci: Set URB actual length for stopped control transfers
  xhci: plat: Register shutdown for xhci_plat
  USB: fix linked-list corruption in rh_call_control()

Pull tty/serial fixes from Greg KH:
 "Here are some small fixes for some serial drivers and Kconfig help
  text for 4.11-rc5. Nothing major here at all, a few things resolving
  reported bugs in some random serial drivers.

  I don't think these made the last linux-next due to me getting to them
  yesterday, but I am not sure, they might have snuck in. The patches
  only affect drivers that the maintainers of sent me these patches for,
  so we should be safe here :)"

* tag 'tty-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: pl011: fix earlycon work-around for QDF2400 erratum 44
  serial: 8250_EXAR: fix duplicate Kconfig text and add missing help text
  tty/serial: atmel: fix TX path in atmel_console_write()
  tty/serial: atmel: fix race condition (TX+DMA)
  serial: mxs-auart: Fix baudrate calculation

Pull ACPI fixes from Rafael Wysocki:
 "These fix two issues related to IOAPIC hotplug, an overzealous build
  optimization that prevents the function graph tracer from working with
  the ACPI subsystem correctly and an RCU synchronization issue in the
  ACPI APEI code.

  Specifics:

   - drop the unconditional setting of the '-Os' gcc flag from the ACPI
     Makefile to make the function graph tracer work correctly with the
     ACPI subsystem (Josh Poimboeuf).

   - add missing synchronize_rcu() to ghes_remove() which removes an
     element from an RCU-protected list, but fails to synchronize it
     properly afterward (James Morse).

   - fix two problems related to IOAPIC hotplug, a local variable
     initialization in setup_res() and the creation of platform device
     objects for IO(x)APICs which are (a) unused and (b) leaked on
     hot-removal (Joerg Roedel)"

* tag 'acpi-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: Fix incompatibility with mcount-based function graph tracing
  ACPI / APEI: Add missing synchronize_rcu() on NOTIFY_SCI removal
  ACPI: Do not create a platform_device for IOAPIC/IOxAPIC
  ACPI: ioapic: Clear on-stack resource before using it

Pull power management fixes from Rafael Wysocki:
 "These fix a cpufreq core issue with the initialization of the cpufreq
  sysfs interface and a cpuidle powernv driver initialization issue.

  Specifics:

   - symbolic links from CPU directories to the corresponding cpufreq
     policy directories in sysfs are not created during initialization
     in some cases which confuses user space, so prevent that from
     happening (Rafael Wysocki).

   - the powernv cpuidle driver fails to pass a correct cpumaks to the
     cpuidle core in some cases which causes subsequent failures to
     occur, so fix it (Vaidyanathan Srinivasan)"

* tag 'pm-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: powernv: Pass correct drv->cpumask for registration
  cpufreq: Fix creation of symbolic links to policy directories

Pull i2c fixes from Wolfram Sang:
 "Two bugfixes from I2C, specifically the I2C mux section. Thanks to
  peda for collecting them"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: mux: pca954x: Add missing pca9546 definition to chip_desc
  Revert "i2c: mux: pca954x: Add ACPI support for pca954x"

Pull ARC fixes from Vineet Gupta:
 "Accumulated fixes for ARC which I've been been sitting on for a while:

   - reading clk from driver vs device tree [Vlad]

   - fix support for UIO in VDK platform [Alexey]

   - SLC busy bit reading workaround

   - build warning with kprobes header reorg"

* tag 'arc-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: fix build warnings with !CONFIG_KPROBES
  ARCv2: SLC: Make sure busy bit is set properly on SLC flushing
  ARC: vdk: Fix support of UIO
  ARCv2: make unimplemented vectors as no-ops rather than halt core
  ARC: get rate from clk driver instead of reading device tree
  ARC: [dts] add cpu nodes to ARCHS SMP device tree
  ARC: [dts] add input clocks for cpu nodes

Pull nfsd fixes from Bruce Fields:
 "The restriction of NFSv4 to TCP went overboard and also broke the
  backchannel; fix.

  Also some minor refinements to the nfsd version-setting interface that
  we'd like to get fixed before release"

* tag 'nfsd-4.11-1' of git://linux-nfs.org/~bfields/linux:
  svcrdma: set XPT_CONG_CTRL flag for bc xprt
  NFSD: fix nfsd_reset_versions for NFSv4.
  NFSD: fix nfsd_minorversion(.., NFSD_AVAIL)
  NFSD: further refinement of content of /proc/fs/nfsd/versions
  nfsd: map the ENOKEY to nfserr_perm for avoiding warning
  SUNRPC/backchanel: set XPT_CONG_CTRL flag for bc xprt

The work-around for the Qualcomm Datacenter Technologies QDF2400
erratum 44 sets the "qdf2400_e44_present" global variable if the
work-around is needed.  However, this check does not happen until after
earlycon is initialized, which means the work-around is not
used, and the console hangs as soon as it displays one character.

Fixes: d8a4995b ("tty: pl011: Work around QDF2400 E44 stuck BUSY bit")
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

write_used was introduced with commit 884b600f ("[PATCH] USB: fix acm
trouble with terminals") but never used since.
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Adds a similar log message to USB_CDC_NOTIFY_SERIAL_STATE as it is
already done with USB_CDC_NOTIFY_NETWORK_CONNECTION.
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>