- 10 Oct, 2017 3 commits
-
-
Yoshihiro Shimoda authored
This patch enables PWM channel 0 and 1 on the draak. Each channel connects to LTC2644 for brightness control. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Yoshihiro Shimoda authored
This patch adds PWM device nodes for r8a77995. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Yoshihiro Shimoda authored
Since a R-Car Gen3 bootloader enables the PFC of USB3.0 channel 0, the USB3.0 host controller works without this setting on the kernel. But, this setting should have salvator-common.dtsi. So, this patch adds the pfc node for USB3.0 channel 0. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
- 05 Oct, 2017 1 commit
-
-
Sergei Shtylyov authored
Add the initial device tree for the R8A77970 SoC based Eagle board. The board has 1 debug serial port (SCIF0); include support for it, so that the serial console can work. Based on the original (and large) patch by Vladimir Barinov <vladimir.barinov@cogentembedded.com>. Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
- 03 Oct, 2017 3 commits
-
-
Yoshihiro Shimoda authored
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling and it will be handled by a phy driver as a gpio pin, this patch removes the "avb_phy_int" from the avb_pins node. Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Fixes: 4503b50e ("arm64: dts: renesas: r8a77995: draak: enable EthernetAVB") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Yoshihiro Shimoda authored
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling and it will be handled by a phy driver as a gpio pin, this patch removes the "avb_phy_int" from the avb_pins node. Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Fixes: 133ace3f ("arm64: dts: ulcb: Set drive-strength for ravb pins") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Yoshihiro Shimoda authored
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling and it will be handled by a phy driver as a gpio pin, this patch removes the "avb_phy_int" from the avb_pins node. Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Fixes: 7d73a4da ("arm64: dts: r8a7795: salvator-x: Set drive-strength for ravb pins") Fixes: 4903987033be ("arm64: dts: r8a7796: salvator-x: Set drive-strength for ravb pins") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
- 25 Sep, 2017 4 commits
-
-
Yoshihiro Shimoda authored
This patch adds USB3.0 peripheral channel 0 device node for r8a7796. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Yoshihiro Shimoda authored
This patch adds USB3.0 peripheral channel 0 device node for r8a7795. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Yoshihiro Shimoda authored
This patch enables EthernetAVB for R-Car D3 draak board. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Yoshihiro Shimoda authored
This patch enables USB2.0 Host (EHCI/OHCI) for r8a77995. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
- 21 Sep, 2017 3 commits
-
-
Yoshihiro Shimoda authored
This patch enables USB2.0 PHY for R-Car D3 draak board. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Yoshihiro Shimoda authored
This patch adds USB2.0 Host (EHCI/OHCI) device node for r8a77995. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Yoshihiro Shimoda authored
This patch adds USB2.0 PHY device node for r8a77995. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
- 19 Sep, 2017 1 commit
-
-
Geert Uytterhoeven authored
Add pin control for SCIF2. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
- 18 Sep, 2017 14 commits
-
-
Sergei Shtylyov authored
Define the generic R8A77970 part of the EtherAVB device node. Based on the original (and large) patch by Daisuke Matsushita <daisuke.matsushita.ns@hitachi.com>. Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Sergei Shtylyov authored
Describe [H]SCIF ports in the R8A77970 device tree. Based on the original (and large) patch by Daisuke Matsushita <daisuke.matsushita.ns@hitachi.com>. Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Sergei Shtylyov authored
Describe SYS-DMAC1/2 in the R8A77970 device tree. Based on the original (and large) patch by Daisuke Matsushita <daisuke.matsushita.ns@hitachi.com>. Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Sergei Shtylyov authored
The initial R8A77970 SoC device tree including Cortex-A53 CPU, GIC, timer, CPG, RST, and SYSC. Based on the original (and large) patch by Daisuke Matsushita <daisuke.matsushita.ns@hitachi.com>. Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Yoshihiro Shimoda authored
This patch adds EthernetAVB device node for r8a77995. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Yoshihiro Shimoda authored
This patch adds GPIO device nodes for r8a77995. Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
Replace the hardcoded clock indices by R8A77995_CLK_* symbols. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
Replace the hardcoded power domain indices by R8A77995_PD_* symbols. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
Add a configuration option for the R-Car V3M SoC. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
Node names should not use numerical suffixes if the nodes can be distinguished by unit-address. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Laurent Pinchart authored
The DU is already wired up to the HDMI encoder, all we need to do is enable it. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Yoshihiro Shimoda authored
This patch changes the name from from e6060000.pfc and pfc@e6060000 to e6060000.pin-controller and pin-controller@e6060000 like other Renesas SoCs. Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Laurent Pinchart authored
The r8a7796 has a single FDP1 instance. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
With W=1: arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/usb@ee0400000 simple-bus unit address format error, expected "ee040000" arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dtb: Warning (simple_bus_reg): Node /soc/usb@ee0400000 simple-bus unit address format error, expected "ee040000" Fixes: 291e0c49 ("arm64: dts: r8a7795: Add support for R-Car H3 ES2.0") Fixes: 171f2ef8 ("arm64: dts: r8a7795: Add USB3.0 host device nodes") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
- 16 Sep, 2017 11 commits
-
-
Linus Torvalds authored
-
git://git.infradead.org/linux-ubifsLinus Torvalds authored
Pull UBI updates from Richard Weinberger: "Minor improvements" * tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs: UBI: Fix two typos in comments ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate" ubi: pr_err() strings should end with newlines ubi: pr_err() strings should end with newlines ubi: pr_err() strings should end with newlines
-
git://git.kernel.org/pub/scm/linux/kernel/git/rw/umlLinus Torvalds authored
Pull UML updates from Richard Weinberger: - minor improvements - fixes for Debian's new gcc defaults (pie enabled by default) - fixes for XSTATE/XSAVE to make UML work again on modern systems * 'for-linus-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml: um: return negative in tuntap_open_tramp() um: remove a stray tab um: Use relative modversions with LD_SCRIPT_DYN um: link vmlinux with -no-pie um: Fix CONFIG_GCOV for modules. Fix minor typos and grammar in UML start_up help um: defconfig: Cleanup from old Kconfig options um: Fix FP register size for XSTATE/XSAVE
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix hotplug deadlock in hv_netvsc, from Stephen Hemminger. 2) Fix double-free in rmnet driver, from Dan Carpenter. 3) INET connection socket layer can double put request sockets, fix from Eric Dumazet. 4) Don't match collect metadata-mode tunnels if the device is down, from Haishuang Yan. 5) Do not perform TSO6/GSO on ipv6 packets with extensions headers in be2net driver, from Suresh Reddy. 6) Fix scaling error in gen_estimator, from Eric Dumazet. 7) Fix 64-bit statistics deadlock in systemport driver, from Florian Fainelli. 8) Fix use-after-free in sctp_sock_dump, from Xin Long. 9) Reject invalid BPF_END instructions in verifier, from Edward Cree. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits) mlxsw: spectrum_router: Only handle IPv4 and IPv6 events Documentation: link in networking docs tcp: fix data delivery rate bpf/verifier: reject BPF_ALU64|BPF_END sctp: do not mark sk dumped when inet_sctp_diag_fill returns err sctp: fix an use-after-free issue in sctp_sock_dump netvsc: increase default receive buffer size tcp: update skb->skb_mstamp more carefully net: ipv4: fix l3slave check for index returned in IP_PKTINFO net: smsc911x: Quieten netif during suspend net: systemport: Fix 64-bit stats deadlock net: vrf: avoid gcc-4.6 warning qed: remove unnecessary call to memset tg3: clean up redundant initialization of tnapi tls: make tls_sw_free_resources static sctp: potential read out of bounds in sctp_ulpevent_type_enabled() MAINTAINERS: review Renesas DT bindings as well net_sched: gen_estimator: fix scaling error in bytes/packets samples nfp: wait for the NSP resource to appear on boot nfp: wait for board state before talking to the NSP ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
Pull more input updates from Dmitry Torokhov: "A second round of updates for the input subsystem: - a new driver for PWM-controlled vibrators - ucb1400 touchscreen driver had completely busted suspend/resume handling - we now handle "home" button found on some devices with Goodix touchscreens - assorted other fixups" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: i8042 - add Gigabyte P57 to the keyboard reset table Input: xpad - validate USB endpoint type during probe Input: ucb1400_ts - fix suspend and resume handling Input: edt-ft5x06 - fix access to non-existing register Input: elantech - make arrays debounce_packet static, reduces object code size Input: surface3_spi - make const array header static, reduces object code size Input: goodix - add support for capacitive home button Input: add a driver for PWM controllable vibrators Input: adi - make array seq static, reduces object code size
-
Markus Trippelsdorf authored
Commit 5620a0d1 ("firmware: delete in-kernel firmware") removed the entire firmware directory. Unfortunately it thereby also removed the support for built-in firmware. This restores the ability to build firmware directly into the kernel by pruning the original Makefile to the necessary minimum. The default for EXTRA_FIRMWARE_DIR is now the standard directory /lib/firmware/. Fixes: 5620a0d1 ("firmware: delete in-kernel firmware") Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de> Acked-by: Greg K-H <gregkh@linuxfoundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Ido Schimmel authored
The driver doesn't support events from address families other than IPv4 and IPv6, so ignore them. Otherwise, we risk queueing a work item before it's initialized. This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES is enabled, as the VRF driver will try to add an l3mdev rule for the IPMR family. Fixes: 65e65ec1 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Andreas Rammhold <andreas@rammhold.de> Reported-by: Florian Klink <flokli@flokli.de> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pavel Machek authored
Fix link in filter.txt. Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Now skb->mstamp_skb is updated later, we also need to call tcp_rate_skb_sent() after the update is done. Fixes: 8c72c65b ("tcp: update skb->skb_mstamp more carefully") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds authored
Pull MIPS updates from Ralf Baechle: "This is the main pull request for 4.14 for MIPS; below a summary of the non-merge commits: CM: - Rename mips_cm_base to mips_gcr_base - Specify register size when generating accessors - Use BIT/GENMASK for register fields, order & drop shifts - Add cluster & block args to mips_cm_lock_other() CPC: - Use common CPS accessor generation macros - Use BIT/GENMASK for register fields, order & drop shifts - Introduce register modify (set/clear/change) accessors - Use change_*, set_* & clear_* where appropriate - Add CM/CPC 3.5 register definitions - Use GlobalNumber macros rather than magic numbers - Have asm/mips-cps.h include CM & CPC headers - Cluster support for topology functions - Detect CPUs in secondary clusters CPS: - Read GIC_VL_IDENT directly, not via irqchip driver DMA: - Consolidate coherent and non-coherent dma_alloc code - Don't use dma_cache_sync to implement fd_cacheflush FPU emulation / FP assist code: - Another series of 14 commits fixing corner cases such as NaN propgagation and other special input values. - Zero bits 32-63 of the result for a CLASS.D instruction. - Enhanced statics via debugfs - Do not use bools for arithmetic. GCC 7.1 moans about this. - Correct user fault_addr type Generic MIPS: - Enhancement of stack backtraces - Cleanup from non-existing options - Handle non word sized instructions when examining frame - Fix detection and decoding of ADDIUSP instruction - Fix decoding of SWSP16 instruction - Refactor handling of stack pointer in get_frame_info - Remove unreachable code from force_fcr31_sig() - Convert to using %pOF instead of full_name - Remove the R6000 support. - Move FP code from *_switch.S to *_fpu.S - Remove unused ST_OFF from r2300_switch.S - Allow platform to specify multiple its.S files - Add #includes to various files to ensure code builds reliable and without warning.. - Remove __invalidate_kernel_vmap_range - Remove plat_timer_setup - Declare various variables & functions static - Abstract CPU core & VP(E) ID access through accessor functions - Store core & VP IDs in GlobalNumber-style variable - Unify checks for sibling CPUs - Add CPU cluster number accessors - Prevent direct use of generic_defconfig - Make CONFIG_MIPS_MT_SMP default y - Add __ioread64_copy - Remove unnecessary inclusions of linux/irqchip/mips-gic.h GIC: - Introduce asm/mips-gic.h with accessor functions - Use new GIC accessor functions in mips-gic-timer - Remove counter access functions from irq-mips-gic.c - Remove gic_read_local_vp_id() from irq-mips-gic.c - Simplify shared interrupt pending/mask reads in irq-mips-gic.c - Simplify gic_local_irq_domain_map() in irq-mips-gic.c - Drop gic_(re)set_mask() functions in irq-mips-gic.c - Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(), gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c. - Convert remaining shared reg access, local int mask access and remaining local reg access to new accessors - Move GIC_LOCAL_INT_* to asm/mips-gic.h - Remove GIC_CPU_INT* macros from irq-mips-gic.c - Move various definitions to the driver - Remove gic_get_usm_range() - Remove __gic_irq_dispatch() forward declaration - Remove gic_init() - Use mips_gic_present() in place of gic_present and remove gic_present - Move gic_get_c0_*_int() to asm/mips-gic.h - Remove linux/irqchip/mips-gic.h - Inline __gic_init() - Inline gic_basic_init() - Make pcpu_masks a per-cpu variable - Use pcpu_masks to avoid reading GIC_SH_MASK* - Clean up mti, reserved-cpu-vectors handling - Use cpumask_first_and() in gic_set_affinity() - Let the core set struct irq_common_data affinity microMIPS: - Fix microMIPS stack unwinding on big endian systems MIPS-GIC: - SYNC after enabling GIC region NUMA: - Remove the unused parent_node() macro R6: - Constify r2_decoder_tables - Add accessor & bit definitions for GlobalNumber SMP: - Constify smp ops - Allow boot_secondary SMP op to return errors VDSO: - Drop gic_get_usm_range() usage - Avoid use of linux/irqchip/mips-gic.h Platform changes: Alchemy: - Add devboard machine type to cpuinfo - update cpu feature overrides - Threaded carddetect irqs for devboards AR7: - allow NULL clock for clk_get_rate BCM63xx: - Fix ENETDMA_6345_MAXBURST_REG offset - Allow NULL clock for clk_get_rate CI20: - Enable GPIO and RTC drivers in defconfig - Add ethernet and fixed-regulator nodes to DTS Generic platform: - Move Boston and NI 169445 FIT image source to their own files - Include asm/bootinfo.h for plat_fdt_relocated() - Include asm/time.h for get_c0_*_int() - Include asm/bootinfo.h for plat_fdt_relocated() - Include asm/time.h for get_c0_*_int() - Allow filtering enabled boards by requirements - Don't explicitly disable CONFIG_USB_SUPPORT - Bump default NR_CPUS to 16 JZ4700: - Probe the jz4740-rtc driver from devicetree Lantiq: - Drop check of boot select from the spi-falcon driver. - Drop check of boot select from the lantiq-flash MTD driver. - Access boot cause register in the watchdog driver through regmap - Add device tree binding documentation for the watchdog driver - Add docs for the RCU DT bindings. - Convert the fpi bus driver to a platform_driver - Remove ltq_reset_cause() and ltq_boot_select( - Switch to a proper reset driver - Switch to a new drivers/soc GPHY driver - Add an USB PHY driver for the Lantiq SoCs using the RCU module - Use of_platform_default_populate instead of __dt_register_buses - Enable MFD_SYSCON to be able to use it for the RCU MFD - Replace ltq_boot_select() with dummy implementation. Loongson 2F: - Allow NULL clock for clk_get_rate Malta: - Use new GIC accessor functions NI 169445: - Add support for NI 169445 board. - Only include in 32r2el kernels Octeon: - Add support for watchdog of 78XX SOCs. - Add support for watchdog of CN68XX SOCs. - Expose support for mips32r1, mips32r2 and mips64r1 - Enable more drivers in config file - Add support for accessing the boot vector. - Remove old boot vector code from watchdog driver - Define watchdog registers for 70xx, 73xx, 78xx, F75xx. - Make CSR functions node aware. - Allow access to CIU3 IRQ domains. - Misc cleanups in the watchdog driver Omega2+: - New board, add support and defconfig Pistachio: - Enable Root FS on NFS in defconfig Ralink: - Add Mediatek MT7628A SoC - Allow NULL clock for clk_get_rate - Explicitly request exclusive reset control in the pci-mt7620 PCI driver. SEAD3: - Only include in 32 bit kernels by default VoCore: - Add VoCore as a vendor t0 dt-bindings - Add defconfig file" * '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits) MIPS: Refactor handling of stack pointer in get_frame_info MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems MIPS: microMIPS: Fix decoding of swsp16 instruction MIPS: microMIPS: Fix decoding of addiusp instruction MIPS: microMIPS: Fix detection of addiusp instruction MIPS: Handle non word sized instructions when examining frame MIPS: ralink: allow NULL clock for clk_get_rate MIPS: Loongson 2F: allow NULL clock for clk_get_rate MIPS: BCM63XX: allow NULL clock for clk_get_rate MIPS: AR7: allow NULL clock for clk_get_rate MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset mips: Save all registers when saving the frame MIPS: Add DWARF unwinding to assembly MIPS: Make SAVE_SOME more standard MIPS: Fix issues in backtraces MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree MIPS: Ci20: Enable RTC driver watchdog: octeon-wdt: Add support for 78XX SOCs. watchdog: octeon-wdt: Add support for cn68XX SOCs. watchdog: octeon-wdt: File cleaning. ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pciLinus Torvalds authored
Pull PCI fix from Bjorn Helgaas: "Revert an attempt to fix a race while enabling upstream bridges because it broke iwlwifi firmware loading" * tag 'pci-v4.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: Revert "PCI: Avoid race while enabling upstream bridges"
-