- 28 Jan, 2008 40 commits
-
-
Pavel Emelyanov authored
The conntracks subsystem has a similar infrastructure to maintain ctl_paths, but since we already have it on the generic level, I think it's OK to switch to using it. So, basically, this patch just replaces the ctl_table-s with ctl_path-s, nf_register_sysctl_table with register_sysctl_paths() and removes no longer needed code. After this the net/netfilter/nf_sysctl.c file contains the paths only. Signed-off-by:
Pavel Emelyanov <xemul@openvz.org> Acked-by:
Patrick McHardy <kaber@trash.net> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Pavel Emelyanov authored
This includes the most simple cases for netfilter. The first part is tne queue modules for ipv4 and ipv6, on which the net/ipv4/ and net/ipv6/ paths are reused from the appropriate ipv4 and ipv6 code. The conntrack module is also patched, but this hunk is very small and simple. Signed-off-by:
-
Pavel Emelyanov authored
This one is almost the same as the hunks in the first patch, but ax25 tables are created dynamically. So this patch differs a bit to handle this case. Signed-off-by:
-
Pavel Emelyanov authored
The decnet includes two places to patch. The first one is the net/decnet table itself, and it is patched just like other subsystems in the first patch in this series. The second place is a bit more complex - it is the net/decnet/conf/xxx entries,. similar to those in ipv4/devinet.c and ipv6/addrconf.c. This code is made similar to those in ipv[46]. Signed-off-by:
-
Pavel Emelyanov authored
The feature of ipvs ctls is that the net/ipv4/vs path is common for core ipvs ctls and for two schedulers, so I make it exported and re-use it in modules. Two other .c files required linux/sysctl.h to make the extern declaration of this path compile well. Signed-off-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
Pavel Emelyanov authored
This patch includes many places, that only required replacing the ctl_table-s with appropriate ctl_paths and call register_sysctl_paths(). Nothing special was done with them. Signed-off-by:
-
Rami Rosen authored
- The DNAT (Destination NAT) is not implemented in IPV4. - This patch remove the code which checks these flags in net/ipv4/arp.c and net/ipv4/route.c. The RTCF_NAT and RTCF_NAT should stay in the header (linux/in_route.h) because they are used in DECnet. Signed-off-by:
Rami Rosen <ramirose@gmail.com> Signed-off-by:
-
Eric Dumazet authored
We can avoid divides (as seen with CONFIG_CC_OPTIMIZE_FOR_SIZE=y on x86) changing vlan_group_get_device()/vlan_group_set_device() id parameter from signed to unsigned. Signed-off-by:
Eric Dumazet <dada1@cosmosbay.com> Signed-off-by:
-
Julia Lawall authored
The file net/tipc/port.c takes a lock using the function tipc_port_lock and then releases the lock sometimes using tipc_port_unlock and sometimes using spin_unlock_bh(p_ptr->publ.lock). tipc_port_unlock simply does the spin_unlock_bh, but it seems cleaner to use it everywhere. The problem was fixed using the following semantic patch. (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ struct port *p_ptr; @@ p_ptr = tipc_port_lock(...) ... ( p_ptr = tipc_port_lock(...); | ?- spin_unlock_bh(p_ptr->publ.lock); + tipc_port_unlock(p_ptr); ) // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Acked-by:
Jon Paul Maloy <maloy@donjonn.com> Signed-off-by:
-
Ivo van Doorn authored
Some devices have a seperate LED which indicates if the radio is enabled or not. This adds a LED trigger to mac80211 where drivers can hook into when they are interested in radio status changes. v2: Check hw.conf.radio_enabled when calling start(). Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Andrew Lutomirski authored
I would argue that mac80211 should handle fixed rates outside the rate control code, which would also allow them to take effect immediately instead of during the rate control callback, but this is pretty close to correct. Signed-Off-By:
Andy Lutomirski <luto@myrealbox.com> Signed-off-by:
-
Johannes Berg authored
This patch changes mac80211's Kconfig/Makefile to: * select between the PID and the SIMPLE rate control algorithm as default * always allow tri-state for the rate control algorithms, building those that are selected 'y' into the mac80211 module (if that is a module, otherwise all into the kernel) * force the default rate control algorithm to be built into mac80211 It also makes both rate control algorithms proper modules again with MODULE_LICENSE etc. Only if EMBEDDED is the user allowed to select "NONE" as default which will cause no algorithm to be selected, this will work only when the driver brings one itself (e.g. iwlwifi drivers). Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Ron Rindjunsky authored
This patch opens the flow to DELBA management frames, and handles end of A-MPDU session produced by this event. Signed-off-by:
Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by:
-
Ron Rindjunsky authored
This patch adds the ability to handle Block Ack Request Signed-off-by:
-
Ron Rindjunsky authored
This patch handles the reordering of the Rx A-MPDU. This issue occurs when the sequence of the internal MPDUs is not in the right order. such a case can be encountered for example when some MPDUs from previous aggregations were recieved, while others failed, so current A-MPDU will contain a mix of re-transmited MPDUs and new ones. Signed-off-by:
-
Ron Rindjunsky authored
This patch initialize A-MPDU MLME data for Rx sessions. Signed-off-by:
-
Ron Rindjunsky authored
This patch adds the basic needed abilities and functions for A-MPDU Rx session changed functions: - ieee80211_sta_process_addba_request - Rx A-MPDU initialization enabled - ieee80211_stop - stops all A-MPDU Rx in case interface goes down added functions: - ieee80211_send_delba - used for sending out Del BA in A-MPDU sessions - ieee80211_sta_stop_rx_BA_session - stopping Rx A-MPDU session - sta_rx_agg_session_timer_expired - stops A-MPDU Rx use if load is too low Signed-off-by:
-
Ron Rindjunsky authored
This patch adds the needed structures to describe the Rx aggregation MLME per STA new: - struct tid_ampdu_rx: TID aggregation information (Rx) - struct sta_ampdu_mlme: MLME aggregation information for STA changed: - struct sta_info: ampdu_mlme added to describe A-MPDU MLME per STA, and timer_to_tid added to map timer id into TID Signed-off-by:
-
Ron Rindjunsky authored
This patch adds the API to perform A-MPDU actions between mac80211 and low level driver. Signed-off-by:
-
Ron Rindjunsky authored
This patch makes a separation between Rx frame pre-handling which stays in __ieee80211_rx and Rx frame handlers, moving to __ieee80211_rx_handle_packet. Although this separation has no affect in regular mode of operation, this kind of mechanism will be used in A-MPDU frames reordering as it allows accumulation of frames during pre-handling, dispatching them to later handling when necessary. Signed-off-by:
-
Johannes Berg authored
No need to not be. Signed-off-by:
Stefano Brivio <stefano.brivio@polimi.it> Signed-off-by:
-
Stefano Brivio authored
Fix the rate control interval definition. Thanks to Mattias Nissler for spotting this out. Cc: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by:
-
Johannes Berg authored
When this function returns != CONTINUE, it needs to put the station struct it has acquired. Hence, having this unused variable is not just superfluous but also misleading. Signed-off-by:
-
Stefano Brivio authored
Add an entry in MAINTAINERS for rc80211-pid. Cc: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by:
-
Stefano Brivio authored
Set a better value for percentage target for failed frames. The previous value slowed down too much rate increases in case of permanently low activity. While at it, increase readability. Signed-off-by:
-
Stefano Brivio authored
Fix a bug which caused uncorrect refcounting of PHYs in mac80211. Thanks to Johannes Berg for spotting this out. Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Stefano Brivio authored
Simplify and fix rate_control_pid_shift_adjust(). A bug prevented correct mapping of sorted rates, and readability was seriously flawed. Signed-off-by:
-
Stefano Brivio authored
Add a kerneldoc description for parameters which are tunable through debugfs. Signed-off-by:
-
Stefano Brivio authored
Export the non-shifted target_pf value to debugfs, so that it's human-readable. Signed-off-by:
-
Helmut Schaa authored
This patch fixes a problem with rx handling on multiple interfaces. Especially when using hardware-scanning and a wireless driver (i.e. iwlwifi) which is able to receive data while scanning. The rx handlers can modify the skb and the frame control field (see ieee80211_rx_h_remove_qos_control) but since every interface gets its own copy of the skb each should get its own copy of rx.fc too. In my case the wlan0-interface did not remove the qos-control from the frame because the corresponding flag in rx.fc was already removed while processing the frame on the master interface. Therefore somehow corrupted frames were passed to the userspace. Signed-off-by:
Helmut Schaa <hschaa@suse.de> Acked-by:
-
Eric Dumazet authored
xfrm_state_clone() is not used outside of net/xfrm/xfrm_state.c There is no need to export it. Spoted by sparse checker. CHECK net/xfrm/xfrm_state.c net/xfrm/xfrm_state.c:1103:19: warning: symbol 'xfrm_state_clone' was not declared. Should it be static? Signed-off-by:
-
Eric Dumazet authored
CHECK net/packet/af_packet.c net/packet/af_packet.c:1876:14: warning: context imbalance in 'packet_seq_start' - wrong count at exit net/packet/af_packet.c:1888:13: warning: context imbalance in 'packet_seq_stop' - unexpected unlock Signed-off-by:
-
Julia Lawall authored
The function sockfd_lookup uses fget on the value that is stored in the file field of the returned structure, so fput should ultimately be applied to this value. This can be done directly, but it seems better to use the specific macro sockfd_put, which does the same thing. The problem was fixed using the following semantic patch. (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ expression s; @@ s = sockfd_lookup(...) ... + sockfd_put(s); ?- fput(s->file); // </smpl> Signed-off-by:
-
Rami Rosen authored
The info placeholder member of dst_entry seems to be unused in the network stack. Signed-off-by:
-
WANG Cong authored
Since __xfrm_policy_destroy is used to destory the resources allocated by xfrm_policy_alloc. So using the name __xfrm_policy_destroy is not correspond with xfrm_policy_alloc. Rename it to xfrm_policy_destroy. And along with some instances that call xfrm_policy_alloc but not using xfrm_policy_destroy to destroy the resource, fix them. Signed-off-by:
WANG Cong <xiyou.wangcong@gmail.com> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Masahide NAKAMURA authored
o Increment PolError counter when flow_cache_lookup() returns errored pointer. o Increment NoStates counter at larval-drop. Signed-off-by:
Masahide NAKAMURA <nakam@linux-ipv6.org> Signed-off-by:
-
Ilpo Järvinen authored
It seems that ip_build_xmit is no longer used in here and ip_append_data is used. Signed-off-by:
Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by:
-
Ilpo Järvinen authored
Without a number of CONFIG.*DEBUG: net/dccp/ccids/ccid3.c: ccid3_hc_tx_update_x | -170 ccid3_hc_tx_packet_sent | -175 ccid3_hc_tx_packet_recv | -169 ccid3_hc_tx_no_feedback_timer | -192 ccid3_hc_tx_send_packet | -144 5 functions changed, 850 bytes removed, diff: -850 net/dccp/ccids/ccid3.c: ccid3_update_send_interval | +191 1 function changed, 191 bytes added, diff: +191 net/dccp/ccids/ccid3.o: 6 functions changed, 191 bytes added, 850 bytes removed, diff: -659 Signed-off-by:
-
Ilpo Järvinen authored
net/xfrm/xfrm_state.c: xfrm_audit_state_delete | -589 xfrm_replay_check | -542 xfrm_audit_state_icvfail | -520 xfrm_audit_state_add | -589 xfrm_audit_state_replay_overflow | -523 xfrm_audit_state_notfound_simple | -509 xfrm_audit_state_notfound | -521 7 functions changed, 3793 bytes removed, diff: -3793 net/xfrm/xfrm_state.c: xfrm_audit_helper_pktinfo | +522 xfrm_audit_helper_sainfo | +598 2 functions changed, 1120 bytes added, diff: +1120 net/xfrm/xfrm_state.o: 9 functions changed, 1120 bytes added, 3793 bytes removed, diff: -2673 Signed-off-by:
-
Ilpo Järvinen authored
net/ipv4/ipvs/ip_vs_xmit.c: ip_vs_icmp_xmit | -638 ip_vs_tunnel_xmit | -674 ip_vs_nat_xmit | -716 ip_vs_dr_xmit | -682 4 functions changed, 2710 bytes removed, diff: -2710 net/ipv4/ipvs/ip_vs_xmit.c: __ip_vs_get_out_rt | +595 1 function changed, 595 bytes added, diff: +595 net/ipv4/ipvs/ip_vs_xmit.o: 5 functions changed, 595 bytes added, 2710 bytes removed, diff: -2115 Without some CONFIG.*DEBUGs: net/ipv4/ipvs/ip_vs_xmit.o: 5 functions changed, 383 bytes added, 1513 bytes removed, diff: -1130 Signed-off-by:
-
