Lets not re-invent the locking wheel. Remove our bitlock and use
a proper spinlock instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If we lose PCIe link, such as when an unannounced PFLR event occurs, or
when a device is surprise removed, we currently detach the device and
close the netdev. This unfortunately leaves a lot of things still
active, such as the msix_mbx_pf IRQ, and Tx/Rx resources.

This can cause problems because the register reads will return
potentially invalid values which may result in unknown driver behavior.

Begin the process of resetting using fm10k_prepare_for_reset(), much in
the same way as the suspend and resume cycle does. This will attempt to
shutdown as much as possible, in order to prevent possible issues.

A naive implementation for this has issues, because there are now
multiple flows calling the reset logic and setting a reset bit. This
would cause problems, because the "re-attach" routine might call
fm10k_handle_reset() prior to the reset actually finishing. Instead,
we'll add state bits to indicate which flow actually initiated the
reset.

For the general reset flow, we'll assume that if someone else is
resetting that we do not need to handle it at all, so it does not need
its own state bit. For the suspend case, we will simply issue a warning
indicating that we are attempting to recover from this case when
resuming.

For the detached subtask, we'll simply refuse to re-attach until we've
actually initiated a reset as part of that flow.

Finally, we'll stop attempting to manage the mailbox subtask when we're
detached, since there's nothing we can do if we don't have a PCIe
address.

Overall this produces a much cleaner shutdown and recovery cycle for
a PCIe surprise remove event.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2017-10-02

This series contains updates to i40e and i40evf.

Shannon Nelson fixes an issue where when a machine has more CPUs than
queue pairs, the counting gets a "little funky" and turns off Flow
Director.  So to correct it, limit the number of LAN queues initially
allocated to be sure there are some left for Flow Director and other
features.

Lihong cleans up dead code by removing a condition check which cannot
ever be true.

Christophe Jaillet fixes a potential NULL pointer dereference, which
could happen if kzalloc() fails.

Filip corrects the reporting of supported link modes, which was incorrect
for some NICs.  Added support for 'ethtool -m' command, which displays
information about QSFP+ modules.

Mariusz adds functions to read/write the LED registers to control the
LEDS, instead of accessing the registers directly whenever the LEDs
need to be controlled.

Jake fixes a regression where we introduced a scheduling while atomic,
so introduce a separate helper function which will manage its own need
for the mac_filter_hash_lock.  Also cleaned up the "PF" parameter in
i40e_vc_disable_vf() since it is never used and is not needed.  Fixed
a rare case where it is possible that a reset does not occur when
i40e_vc_disable_vf() is called, so modify i40e_reset_vf() to return a
bool to indicate whether it reset or not so that i40e_vc_disable_vf()
can wait until a reset actually occurs.

Alan adds the ability for the VF to request more or less underlying
allocated queues from the PF.  Fixes the incorrect method for clearing
the vf_states variable with a NULL assignment, when we should be
using atomic bitops since we don't actually want to clear all the
flags.  Fixed a resource leak, where the PF driver fails to inform
clients of a VF reset because we were incorrectly checking the
I40E_VF_STATE_PRE_ENABLE bit.

Mitch converts i40evf_map_rings_to_vectors() to a void function since
it cannot fail and allows us to clean up the checks for the function
return value.

Scott enables the driver(s) to pass traffic with VLAN tags using the
802.1ad Ethernet protocol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable i40e to pass traffic with VLAN tags using the 802.1ad ethernet
protocol ID (0x88a8).

This requires NIC firmware providing version 1.7 of the API. With
older NIC firmware 802.1ad tagged packets will continue to be dropped.

No VLAN offloads nor RSS are supported for 802.1ad VLANs.
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently there is a bug in which the PF driver fails to inform clients
of a VF reset which then causes clients to leak resources.  The bug
exists because we were incorrectly checking the I40E_VF_STATE_PRE_ENABLE
bit.

When a VF is first init we go through a reset to initialize variables
and allocate resources but we don't want to inform clients of this first
reset since the client isn't fully enabled yet so we set a state bit
signifying we're in a "pre-enabled" client state.  During the first
reset we should be clearing the bit, allowing all following resets to
notify the client of the reset when the bit is not set.  This patch
fixes the issue by negating the 'test_and_clear_bit' check to accurately
reflect the behavior we want.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we inappropriately clear the vf_states variable with a null
assignment.  This is problematic because we should be using atomic
bitops on this variable and we don't actually want to clear all the
flags.  We should just clear the ones we know we want to clear.
Additionally remove the I40E_VF_STATE_FCOEENA bit because it is no
longer being used.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This function cannot fail, so why is it returning a value? And why are
we checking it? Why shouldn't we just make it void? Why is this commit
message made up of only questions?
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the VF gets a default number of allocated queues from HW on
init and it could choose to enable or disable those allocated queues.
This makes it such that the VF can request more or less underlying
allocated queues from the PF.

First the VF negotiates the number of queues it wants that can be
supported by the PF and if successful asks for a reset.  During reset
the PF will reallocate the HW queues for the VF and will then remap the
new queues.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It is possible although rare that we may not reset when
i40e_vc_disable_vf() is called. This can lead to some weird
circumstances with some values not being properly set. Modify
i40e_reset_vf() to return a code indicating whether it reset or not.

Now, i40e_vc_disable_vf() can wait until a reset actually occurs. If it
fails to free up within a reasonable time frame we'll display a warning
message.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Replace i40e_vc_notify_vf_reset and i40e_reset_vf with a call to
i40e_vc_disable_vf which does this exact thing. This matches similar
code patterns throughout the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It's never used, and the vf structure could get back to the PF if
necessary. Lets just drop the extra unneeded parameter.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When we refactored handling of the PVID in commit 9af52f60
("i40e: use (add|rm)_vlan_all_mac helper functions when changing PVID")
we introduced a scheduling while atomic regression.

This occurred because we now held the spinlock across a call to
i40e_reset_vf(), which results in a usleep_range() call that triggers
a scheduling while atomic bug. This was rare as it only occurred if the
user configured a VLAN on a VF and also attempted to reconfigure the VF
from the host system with a port VLAN.

We do need to hold the lock while calling i40e_is_vsi_in_vlan(), but we
should not be holding it while we reset the VF.

We'll fix this by introducing a separate helper function
i40e_vsi_has_vlans which checks whether we have a PVID and whether the
VSI has configured VLANs. This helper function will manage its own need
for the mac_filter_hash_lock.

Then, we can move the acquiring of the spinlock until after we reset the
VF, which ensures that we do not sleep while holding the lock.

Using a separate function like this makes the code more clear and is
easier to read than attempting to release and re-acquire the spinlock
when we reset the VF.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of accessing register directly, use newly added AQC in
order to blink LEDs. Introduce and utilize a new flag to prevent
excessive API version checking.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for 'ethtool -m' command which displays
information about (Q)SFP+ module plugged into NIC's cage.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes incorrect reporting of supported link modes on some NICs.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If 'kzalloc()' fails, a NULL pointer will be dereferenced.
Return an error code (-ENOMEM) instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes the !vf condition check that cannot be
true in i40e_ndo_set_vf_trust function

Detected by CoverityScan, CID 1397531 Logically dead code
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When a machine has more CPUs than queue pairs, e.g. 512 cores, the
counting gets a little funky and turns off Flow Director with the
message:
  not enough queues for Flow Director. Flow Director feature is disabled

This patch limits the number of lan queues initially allocated to
be sure we have some left for FD and other features.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2017-10-02

This series contains updates to fm10k only.

Jake provides all but one of the changes in this series.  Most are small
fixes, starting with ensuring prompt transmission of messages queued up
after each VF message is received and handled.  Fix a possible race
condition between the watchdog task and the processing of mailbox
messages by just checking whether the mailbox is still open.  Fix a
couple of GCC v7 warnings, including misspelled "fall through" comments
and warnings about possible truncation of calls to snprintf().  Cleaned
up a convoluted bitshift and read for the PFVFLRE register.  Fixed a
potential divide by zero when finding the proper r_idx.

Markus Elfring fixes an issue which was found using Coccinelle, where
we should have been using seq_putc() instead of seq_puts().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Mika Westerberg says:

====================
Thunderbolt networking

In addition of tunneling PCIe, Display Port and USB traffic, Thunderbolt
allows connecting two hosts (domains) over a Thunderbolt cable. It is
possible to tunnel arbitrary data packets over such connection using
high-speed DMA rings available in the Thunderbolt host controller.

In order to discover Thunderbolt services the other host supports, there is
a software protocol running on top of the automatically configured control
channel (ring 0). This protocol is called XDomain discovery protocol and it
uses XDomain properties to describe the host (domain) and the services it
supports.

Once both sides have agreed what services are supported they can enable
high-speed DMA rings to transfer data over the cable.

This series adds support for the XDomain protocol so that we expose each
remote connection as Thunderbolt XDomain device and each service as
Thunderbolt service device. On top of that we create an API that allows
writing drivers for these services and finally we provide an example
Thunderbolt service driver that creates virtual ethernet inferface that
allows tunneling networking packets over Thunderbolt cable. The API could
be used for creating other future Thunderbolt services, such as tunneling
SCSI over Thunderbolt, for example.

The XDomain protocol and networking support is also available in macOS and
Windows so this makes it possible to connect Linux to macOS and Windows as
well.

The patches are based on previous Thunderbolt networking patch series by
Amir Levy and Michael Jamet, that can be found here:

  https://lwn.net/Articles/705998/

The main difference to that patch series is that we have the XDomain
protocol running in the kernel now so there is no need for a separate
userspace daemon.

Note this does not affect the existing functionality, so security levels
and NVM firmware upgrade continue to work as before (with the small
exception that now sysfs also shows the XDomain connections and services in
addition to normal Thunderbolt devices). It is also possible to connect up
to 5 Thunderbolt devices and then another host, and the network driver
works exactly the same.

This is third version of the patch series. The previous versions can be
be found here:

  v2: https://lkml.org/lkml/2017/9/25/225
  v1: https://lwn.net/Articles/734019/

Changes from the v2:

  * Add comment regarding calculation of interrupt throttling value
  * Add UUIDs as strings in comments on top of each declaration
  * Add a patch removing __packed from existing ICM messages. They are all
    32-bit aligned and should pack fine without the __packed.
  * Move adding MAINTAINERS entries to a separate patches
  * Added Michael and Yehezkel to be maintainers of the network driver
  * Remove __packed from the new ICM messages. They should pack fine as
    well without it.
  * Call register_netdev() after all other initialization is done in the
    network driver.
  * Use build_skb() instead of copying. We allocate order 1 page here to
    leave room for SKB shared info required by build_skb(). However, we do
    not leave room for full NET_SKB_PAD because the NHI hardware does not
    cope well if a frame crosses 4kB boundary. According comments in
    __build_skb() that should still be fine.
  * Added Reviewed-by tag from Andy.

Changes from the v1:

  * Add include/linux/thunderbolt.h to MAINTAINERS
  * Correct Linux version and date of new sysfs entries in
    Documentation/ABI/testing/sysfs-bus-thunderbolt
  * Move network driver from drivers/thunderbolt/net.c to
    drivers/net/thunderbolt.c and update it to follow coding style in
    drivers/net/*.
  * Add MAINTAINERS entry for the network driver
  * Minor cleanups

In case someone wants to try this out, the last patch adds documentation
how the networking driver can be used. In short, if you connect Linux to a
macOS or Windows, everything is done automatically (as those systems have
the networking service enabled by default). For Linux to Linux connection
one host needs to load the networking driver first (so that the other side
can locate the networking service and load the corresponding driver).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

I will be maintaining the Thunderbolt network driver along with Michael
and Yehezkel.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ThunderboltIP is a protocol created by Apple to tunnel IP/ethernet
traffic over a Thunderbolt cable. The protocol consists of configuration
phase where each side sends ThunderboltIP login packets (the protocol is
determined by UUID in the XDomain packet header) over the configuration
channel. Once both sides get positive acknowledgment to their login
packet, they configure high-speed DMA path accordingly. This DMA path is
then used to transmit and receive networking traffic.

This patch creates a virtual ethernet interface the host software can
use in the same way as any other networking interface. Once the
interface is brought up successfully network packets get tunneled over
the Thunderbolt cable to the remote host and back.

The connection is terminated by sending a ThunderboltIP logout packet
over the configuration channel. We do this when the network interface is
brought down by user or the driver is unloaded.
Signed-off-by: Amir Levy <amir.jer.levy@intel.com>
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new API header (include/linux/thunderbolt.h) is maintained by the
Thunderbolt driver maintainers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thunderbolt services should not care which HopID (ring) they use for
sending and receiving packets over the high-speed DMA path, so make
tb_ring_alloc_rx() and tb_ring_alloc_tx() accept negative HopID. This
means that the NHI will allocate next available HopID for the caller
automatically.

These HopIDs will be allocated from the range which is not reserved for
the Thunderbolt protocol (8 .. hop_count - 1).

The allocated HopID can be retrieved from ring->hop field after the ring
has been allocated successfully if needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is needed when Thunderbolt service drivers need to DMA map memory
before it is passed down to the ring.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to support things like networking over Thunderbolt cable, there
needs to be a way to switch the ring to a mode where it can be polled
with the interrupt masked. We implement such mode so that the caller can
allocate a ring by passing pointer to a function that is then called
when an interrupt is triggered. Completed frames can be fetched using
tb_ring_poll() and the interrupt can be re-enabled when the caller is
finished with polling by using tb_ring_poll_complete().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is needed because ring polling functionality can be called from
atomic contexts when networking and other high-speed traffic is
transferred over a Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This makes it possible to enqueue frames also from atomic context which
is needed for example, when networking packets are sent over a
Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A Thunderbolt service driver might need to check if there was an error
with the descriptor when in frame mode. We also add two Rx specific
error flags RING_DESC_CRC_ERROR and RING_DESC_BUFFER_OVERRUN.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are used by Thunderbolt services to send and receive frames over
the high-speed DMA rings.

We also put the functions to tb_ namespace to make sure we do not
collide with others and add missing kernel-doc comments for the exported
functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When high-speed DMA paths are used to transfer arbitrary data over a
Thunderbolt link, DMA rings should be in frame mode instead of raw mode.
The latter is used by the control channel (ring 0). In frame mode each
data frame can hold up to 4kB payload.

This patch modifies the DMA ring code to allow configuring a ring to be
in frame mode by passing a new flag (RING_FLAG_FRAME) to the ring when
it is allocated. In addition there might be need to enable end-to-end
(E2E) workaround for the ring to prevent losing Rx frames in certain
situations. We add another flag (RING_FLAG_E2E) that can be used for
this purpose.

This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This will keep the interrupt delivery rate reasonable. The value used
here (128 us) is a recommendation from the hardware people.

This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When two hosts are connected over a Thunderbolt cable, there is a
protocol they can use to communicate capabilities supported by the host.
The discovery protocol uses automatically configured control channel
(ring 0) and is build on top of request/response transactions using
special XDomain primitives provided by the Thunderbolt base protocol.

The capabilities consists of a root directory block of basic properties
used for identification of the host, and then there can be zero or more
directories each describing a Thunderbolt service and its capabilities.

Once both sides have discovered what is supported the two hosts can
setup high-speed DMA paths and transfer data to the other side using
whatever protocol was agreed based on the properties. The software
protocol used to communicate which DMA paths to enable is service
specific.

This patch adds support for the XDomain discovery protocol to the
Thunderbolt bus. We model each remote host connection as a Linux XDomain
device. For each Thunderbolt service found supported on the XDomain
device, we create Linux Thunderbolt service device which Thunderbolt
service drivers can then bind to based on the protocol identification
information retrieved from the property directory describing the
service.

This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A Thunderbolt service might need to find the physical port from a link
the cable is connected to. For instance networking driver uses this
information to generate MAC address according the Apple ThunderboltIP
protocol.

Move this function to thunderbolt.h and rename it to
tb_phy_port_from_link() to reflect the fact that it does not take switch
as parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are needed by Thunderbolt services so move them to thunderbolt.h
to make sure they are available outside of drivers/thunderbolt.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These will be needed by Thunderbolt services when sending and receiving
XDomain control messages. While there change TB_CFG_PKG_PREPARE_TO_SLEEP
value to be decimal in order to be consistent with other members.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thunderbolt XDomain discovery protocol uses directories which contain
properties and other directories to exchange information about what
capabilities the remote host supports. This also includes identification
information like device ID and name.

This adds support for parsing and formatting these properties and
establishes an API drivers can use in addition to the core Thunderbolt
driver. This API is exposed in a new header: include/linux/thunderbolt.h.

This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These messages are all 32-bit aligned and they should be packed without
the __packed attribute just fine. It also allows compiler to generate
better code on some architectures.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We will be using these when communicating XDomain discovery protocol
over Thunderbolt link but they might be useful for other drivers as
well.

Make them available through byteorder/generic.h.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Fixlets

Couple of small nit fixes from Petr
====================
Signed-off-by: David S. Miller <davem@davemloft.net>