- 09 Jan, 2014 19 commits
-
-
Bing Zhao authored
Instead of having two copies of the code for device tree cfgdata downloading, add a function to improve the code. Reviewed-by:
Paul Stewart <pstew@chromium.org> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Bing Zhao authored
If cfgdata length exceeds the command buffer size we will end up getting buffer overflow problem. Fix it by checking the buffer size less the command header length. Reviewed-by:
-
Vladimir Kondratiev authored
As soon as skb is ready to be reaped, prefetch 1-st cache line. This accelerates data access that is performed later, during the packet classification by the driver and IP stack. Signed-off-by:
Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by:
-
Vladimir Kondratiev authored
Bit DMA_CFG_DESC_TX_OFFLOAD_CFG_L3T_IPV4_POS should be set for IPv4 only. Don't set it for IPv6 Signed-off-by:
-
Vladimir Kondratiev authored
Use hardware capabilities to limit IRQ generation to about 15 per msec It corresponds to about 7 packets/IRQ when running iperf with default parameters at 1.3Gbps Do not enable this feature in the sniffer (monitor) mode, because interrupt moderation cause timestamp accuracy deterioration. For the sniffer flow, it is important to get precise timestamp. Signed-off-by:
-
Arend van Spriel authored
This patch adds support for the bcm43362 1x1 11n chipset. This chipset is used in AP6210 wifi module found on Cubieboard [1]. [1] http://cubieboard.org/Reviewed-by:
Franky Lin <frankyl@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Pavel Machek authored
wl1251: fix NULL pointer dereference Signed-off-by:
Pali Rohár <pali.rohar@gmail.com> Reported-by:
Felipe Contreras <felipe.contreras@gmail.com> Signed-off-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
-
Pavel Machek authored
Add nvs file name to module firmware list Signed-off-by:
-
David Gnedt authored
The firmware doesn't support per packet encryption selection, so disable hw encryption support completely while a monitor interface is present to support injection of packets (which shouldn't get encrypted by hw). To enforce the changed hw encryption support force a disassociation on non-monitor interfaces. For disassociation a workaround using hw connection monitor is employed, which temporary enables hw connection manager flag. Signed-off-by:
David Gnedt <david.gnedt@davizone.at> Signed-off-by:
-
David Gnedt authored
Set the retry limit to 0 and disable the ACK policy for injected packets. Signed-off-by:
-
David Gnedt authored
If necessary enable the tx path in monitor mode for packet injection using the JOIN command with BSS_TYPE_STA_BSS and zero BSSID. Signed-off-by:
-
David Gnedt authored
Use the ENABLE_RX command for channel switching when no interface is present (monitor mode only). The advantage of ENABLE_RX is that it leaves the tx data path disabled in firmware, whereas the usual JOIN command seems to transmit some frames at firmware level. Signed-off-by:
-
David Gnedt authored
Force power saving off while monitor interface is present. Signed-off-by:
-
David Gnedt authored
Port multicast address filtering from wl1271 driver. It sets up the hardware multicast address filter in configure_filter() with addresses supplied through prepare_multicast(). Signed-off-by:
-
David Gnedt authored
Disable hardware encryption (DF_ENCRYPTION_DISABLE) and decryption (DF_SNIFF_MODE_ENABLE) via wl1251_acx_feature_cfg while monitor interface is present. Signed-off-by:
-
David Gnedt authored
Split up data path initialisation into RX and TX data path initialisation functions. This change is required for channel switching in monitor mode. Signed-off-by:
-
David Gnedt authored
Update hardware ARP filter configuration on BSS_CHANGED_ARP_FILTER notification from mac80211. Ported from wl1271 driver. Signed-off-by:
-
David Gnedt authored
Port of the power save entry retry code from wl1251 driver version included in the Maemo Fremantle kernel. This tries to enable power save mode up to 3 times before failing. Signed-off-by:
-
David Gnedt authored
With a dissasociated card I often encoutered very long scan delays. My guess is that it has something to do with the cards DTIM handling and another firmware bug mentioned in the TI WLAN driver, which is described as the card may never end scanning if the channel is overloaded because it can't send probe requests. I think the firmware somehow also tries to receive DTIM messages when the BSSID is not set. Therefore most of the time it waits for DTIM messages and can't do scanning work. Anyway we can workaround this misbehaviour by setting the HIGH_PRIORITY bit for scans in disassociated state. Signed-off-by:
-
- 08 Jan, 2014 1 commit
-
-
John W. Linville authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
-
- 07 Jan, 2014 2 commits
-
-
Claudio Takahasi authored
This patch fixes peer address lookup for 6loWPAN over Bluetooth Low Energy links. ADDR_LE_DEV_PUBLIC, and ADDR_LE_DEV_RANDOM are the values allowed for "dst_type" field in the hci_conn struct for LE links. Signed-off-by:
Claudio Takahasi <claudio.takahasi@openbossa.org> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk>
-
Claudio Takahasi authored
This patch fixes the Bluetooth Low Energy Address type checking when setting Universal/Local bit for the 6loWPAN network device or for the peer device connection. ADDR_LE_DEV_PUBLIC or ADDR_LE_DEV_RANDOM are the values allowed for "src_type" and "dst_type" in the hci_conn struct. The Bluetooth link type can be obtainned reading the "type" field in the same struct. Signed-off-by:
-
- 06 Jan, 2014 18 commits
-
-
Gianluca Anzolin authored
Remove the rfcomm_carrier_raised() definition as that function isn't used anymore. Signed-off-by:
Gianluca Anzolin <gianluca@sottospazio.it> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org>
-
Gianluca Anzolin authored
This patch fixes two regressions introduced with the recent rfcomm tty rework. The current code uses the carrier_raised() method to wait for the bluetooth connection when a process opens the tty. However processes may open the port with the O_NONBLOCK flag or set the CLOCAL termios flag: in these cases the open() syscall returns immediately without waiting for the bluetooth connection to complete. This behaviour confuses userspace which expects an established bluetooth connection. The patch restores the old behaviour by waiting for the connection in rfcomm_dev_activate() and removes carrier_raised() from the tty_port ops. As a side effect the new code also fixes the case in which the rfcomm tty device is created with the flag RFCOMM_REUSE_DLC: the old code didn't call device_move() and ModemManager skipped the detection probe. Now device_move() is always called inside rfcomm_dev_activate(). Signed-off-by:
Andrey Vihrov <andrey.vihrov@gmail.com> Reported-by:
Beson Chow <blc+bluez@mail.vanade.com> Signed-off-by:
-
Gianluca Anzolin authored
This is a preparatory patch which moves the rfcomm_get_device() definition before rfcomm_dev_activate() where it will be used. Signed-off-by:
-
Gianluca Anzolin authored
This patch fixes a userspace regression introduced by the commit 29cd718b. If the rfcomm device was created with the flag RFCOMM_RELEASE_ONHUP the user space expects that the tty_port is released as soon as the last process closes the tty. The current code attempts to release the port in the function rfcomm_dev_state_change(). However it won't get a reference to the relevant tty to send a HUP: at that point the tty is already destroyed and therefore NULL. This patch fixes the regression by taking over the tty refcount in the tty install method(). This way the tty_port is automatically released as soon as the tty is destroyed. As a consequence the check for RFCOMM_RELEASE_ONHUP flag in the hangup() method is now redundant. Instead we have to be careful with the reference counting in the rfcomm_release_dev() function. Signed-off-by:
Alexander Holler <holler@ahsoftware.de> Signed-off-by:
-
Arend van Spriel authored
The SDIO identifier for Broadcom WLAN devices were defined in the brcmfmac SDIO driver. Moving the definitions in MMC header file seems common sense. Reviewed-by:
-
Arend van Spriel authored
The destructor for net devices was set to free_netdev() to get rid of it and the private data. The private data refers to a brcmf_if instance, but indirectly it also refers to brcmf_cfg80211_vif which holds the wdev. This is freed as well by using a new custom destructor called brcmf_cfg80211_free_netdev(). Reviewed-by:
-
Arend van Spriel authored
Instead of calling brcmf_cfg80211_detach() in brcmf_del_if() when deleting the primary interface, call it in brcmf_detach() after deleting all interfaces. Reviewed-by:
-
Arend van Spriel authored
The wiphy_unregister() call was done in brcmf_free_vif() when the last interface was being removed. This is not the obvious place to do that. This patch moves it to the brcmf_cfg80211_detach(). This removes the need to keep count of interfaces. Reviewed-by:
-
Arend van Spriel authored
Upon unload of the brcmfmac driver it gave a kernel warning because cfg80211 still believed to be connected to an AP. The brcmfmac had already transitioned to disconnected state during unload. This patch adds informing cfg80211 about this transition. This will get rid of warning from cfg80211 seen upon module unload: ------------[ cut here ]------------ WARNING: CPU: 3 PID: 24303 at net/wireless/core.c:952 cfg80211_netdev_notifier_call+0x193/0x640 [cfg80211]() Modules linked in: brcmfmac(O-) brcmutil(O) cfg80211(O) ... [last unloaded: bcma] CPU: 3 PID: 24303 Comm: rmmod Tainted: G W O 3.13.0-rc4-wl-testing-x64-00002-gb472b6d-dirty #1 Hardware name: Dell Inc. Latitude E6410/07XJP9, BIOS A07 02/15/2011 00000000000003b8 ffff8800b211faf8 ffffffff815a7fcd 0000000000000007 0000000000000000 ffff8800b211fb38 ffffffff8104819c ffff880000000000 ffff8800c889d008 ffff8800b2000220 ffff8800c889a000 ffff8800c889d018 Call Trace: [<ffffffff815a7fcd>] dump_stack+0x46/0x58 [<ffffffff8104819c>] warn_slowpath_common+0x8c/0xc0 [<ffffffff810481ea>] warn_slowpath_null+0x1a/0x20 [<ffffffffa173fd83>] cfg80211_netdev_notifier_call+0x193/0x640 [cfg80211] [<ffffffff81521ca8>] ? arp_ifdown+0x18/0x20 [<ffffffff8152d75a>] ? fib_disable_ip+0x3a/0x50 [<ffffffff815b143d>] notifier_call_chain+0x4d/0x70 [<ffffffff8106d6e6>] raw_notifier_call_chain+0x16/0x20 [<ffffffff814b9ae0>] call_netdevice_notifiers_info+0x40/0x70 [<ffffffff814b9b26>] call_netdevice_notifiers+0x16/0x20 [<ffffffff814bb59d>] rollback_registered_many+0x17d/0x280 [<ffffffff814bb74d>] rollback_registered+0x2d/0x40 [<ffffffff814bb7c8>] unregister_netdevice_queue+0x68/0xd0 [<ffffffff814bb9c0>] unregister_netdev+0x20/0x30 [<ffffffffa180069e>] brcmf_del_if+0xce/0x180 [brcmfmac] [<ffffffffa1800b3c>] brcmf_detach+0x6c/0xe0 [brcmfmac] Reviewed-by:
-
Arend van Spriel authored
The condition to disable the clock at the end of brcmf_sdio_bus_init() was wrong as the bus state is updated by the calling function. Hence, the clock was always disabled after brcmf_sdio_bus_init() which was not the intended behaviour. Reviewed-by:
-
Arend van Spriel authored
Change condition in brcmf_sdio_wd_timer() function to program watchdog only when in BRCMF_BUS_DATA state. This avoids watchdog being active during initialization. During initialization the SDIO save&restore capability is determined which affect the bus sleep mechanism used in watchdog thread. Reviewed-by:
-
Arend van Spriel authored
The detection of the save&restore capability in brcmf_sdio_sr_capable() is only valid for certain chipsets. This patch should cover it for all chipsets currently supported. Reviewed-by:
-
Arend van Spriel authored
The table for BCM4334 SDIO drive strength programming was missing from the driver. Adding it with this patch set. Reviewed-by:
-
Arend van Spriel authored
Using 'iw phy' only showed HT20 support in the HT capabilities info. This patch determines support for HT40 using a firmware query that is supposed to work for all supported devices. Reviewed-by:
-
Arend van Spriel authored
Moving code from helper functions to the calling function as it makes code easier to read. Reviewed-by:
-
Arend van Spriel authored
Two helper functions in the sdio remove path were very thin and only used once. So its code is moved to the calling function. Reviewed-by:
-
Hante Meuleman authored
An control request or set message length is restricted to ETH frame length for the buffer from host to device. This is limitation is imposed by the firmware. Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
