This change cleans up the i40e/i40evf_set_itr_per_queue function by
dropping all the unneeded pointer chases. Instead we can just pull out the
pointers for the Tx and Rx rings and use them throughout the function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds back the capability to turn off offloads when VF has
VLAN set. The commit 0a3b4f70 ("i40evf: enable support for VF VLAN
tag stripping control") adds the i40evf_set_features function and
changes the 'turn off' flow for offloads. This patch adds that
capability back by moving checking the VLAN option for VF to the
next statement.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch reorders i40e_add_del_fdir and i40e_update_ethtool_fdir_entry
calls so that we first remove an already existing filter (inside
i40e_update_ethtool_fdir_entry using i40e_add_del_fdir) and then
we add a new one with i40e_add_del_fdir.
After applying this patch, creating multiple identical filters (with
the same location) one after another doesn't revert their behavior
but behaves correctly.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The FW has the ability to return a critical error on every AQ command.
When this critical error occurs then we need to send the correct response
to the caller.
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Message sends to the local broadcast address (255.255.255.255) require
uc_index or sk_bound_dev_if to be set to an egress device. However,
responses or only received if the socket is bound to the device. This
is overly constraining for processes running in an L3 domain. This
patch allows a socket bound to the VRF device to send to the local
broadcast address by using IP_UNICAST_IF to set the egress interface
with packet receipt handled by the VRF binding.

Similar to IP_MULTICAST_IF, relax the constraint on setting
IP_UNICAST_IF if a socket is bound to an L3 master device. In this
case allow uc_index to be set to an enslaved if sk_bound_dev_if is
an L3 master device and is the master device for the ifindex.

In udp and raw sendmsg, allow uc_index to override the oif if
uc_index master device is oif (ie., the oif is an L3 master and the
index is an L3 slave).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

William Tu says:

====================
net: erspan: add support for openvswitch

The first patch refactors the erspan header definitions.
Originally, the erspan fields are defined as a group into a __be16 field,
and use mask and offset to access each field.  This is more costly due to
calling ntohs/htons and error-prone.  The first patch changes it to use
bitfields.  The second patch creates erspan.h in UAPI and move the definition
'struct erspan_metadata' to it for later openvswitch to use.  The final patch
introduces the new OVS tunnel key attribute, OVS_TUNNEL_KEY_ATTR_ERSPAN_OPTS,
to program both v1 and v2 erspan tunnel for openvswitch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds support for openvswitch to configure erspan
v1 and v2.  The OVS_TUNNEL_KEY_ATTR_ERSPAN_OPTS attr is added
to uapi as a binary blob to support all ERSPAN v1 and v2's
fields.  Note that Previous commit "openvswitch: Add erspan tunnel
support." was reverted since it does not design properly.
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds a new uapi header file, erspan.h, and moves
the 'struct erspan_metadata' from internal erspan.h to it.
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Originally the erspan fields are defined as a group into a __be16 field,
and use mask and offset to access each field.  This is more costly due to
calling ntohs/htons.  The patch changes it to use bitfields.
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
use tc_cls_can_offload_and_chain0() throughout the drivers

This set makes all drivers use a new tc_cls_can_offload_and_chain0()
helper which will set extack in case TC hw offload flag is disabled.

I chose to keep the new helper which also looks at the chain but
renamed it more appropriately.  The rationale being that most drivers
don't accept chains other than 0 and since we have to pass extack
to the helper we can as well pass the entire struct tc_cls_common_offload
and perform the most common checks.

This code makes the assumption that type_data in the callback can
be interpreted as struct tc_cls_common_offload, i.e. the real offload
structure has common part as the first member.  This allows us to
make the check once for all classifier types if driver supports
more than one.

v1:
 - drop the type validation in nfp and netdevsim.
v2:
 - reorder checks in patch 1;
 - split other changes from patch 1;
 - add the i40e patch in;
 - add one more test case - for chain 0 extack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure netdevsim doesn't allow offload of chains other than 0,
and that it reports the expected extack message.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Drivers should not report errors when offload is not forced.
Check stdout and stderr for familiar messages when with no
skip flags and with skip_hw.  Check for add, replace, and
destroy.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Very few (mlxsw) upstream drivers seem to allow offload of chains
other than 0.  Save driver developers typing and add a helper for
checking both if ethtool's TC offload flag is on and if chain is 0.
This helper will set the extack appropriately in both error cases.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Issue found by checkpatch.
Signed-off-by: Rohit Visavalia <rohit.visavalia@softnautics.com>
Acked-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Resolved Warning: networking block comments don't use an empty /* line,
use /* Comment...
Issue found by checkpatch.
Signed-off-by: Rohit Visavalia <rohit.visavalia@softnautics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2018-01-25

Here's one last bluetooth-next pull request for the 4.16 kernel:

 - Improved support for Intel controllers
 - New set_parity method to serdev (agreed with maintainers to be taken
   through bluetooth-next)
 - Fix error path in hci_bcm (missing call to serdev close)
 - New ID for BCM4343A0 UART controller

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

t4_wr_mbox_meat_timeout() can be called from both softirq
context and process context, hence protect the mbox with
spin_lock_bh() instead of simple spin_lock()
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6 allows routes to be installed when the device is not up (admin up).
Worse, it does not mark it as LINKDOWN. IPv4 does not allow it and really
there is no reason for IPv6 to allow it, so check the flags and deny if
device is admin down.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: more socket closing improvements

these patches improve the smc behavior for abnormal socket closing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If a problem for at least one connection of a link group is detected,
the whole link group and all its connections are terminated.
This patch adds a check for healthy link group when trying to reserve
a work request, and checks for healthy connections before starting
a tx worker.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a new connection with a new rmb is added to a link group, its
memory region is registered. If a link group is terminated, a pending
registration requires a wake up.

And consolidate setting of tx_flag peer_conn_abort in smc_lgr_terminate().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once a linkgroup is created successfully, it stays alive for a
certain time to service more connections potentially created.
If one of the initialization steps for a new linkgroup fails,
the linkgroup should not be reused by other connections following.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If ib_post_send() fails, terminate all connections of this
link group.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A state transition from closing state SMC_PEERFINCLOSEWAIT to closing
state SMC_APPFINCLOSEWAIT is not allowed. Once a closing indication
from the peer has been received, the socket reaches state SMC_CLOSED.

And receiving a peer_conn_abort just changes the state of the socket
into one of the states SMC_PROCESSABORT or SMC_CLOSED;
sending a peer_conn_abort occurs in smc_close_active() for state
SMC_PROCESSABORT only.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If an SMC socket is aborted, the tx worker should be cancelled.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Edward Cree says:

====================
sfc: support PTP on 8000 and X2000 series NICs

Starting from the 8000-series (Medford 1), SFC NICs can timestamp TX packets
 sent through an ordinary DMA queue, rather than a special control-plane
 operation as in the 7000-series.  Patches 2-8 implement support for this.
The X2000-series (Medford 2) changes the format of timestamps, from seconds+
 (2^27)ths to seconds + quarter nanoseconds, as well as changing the shift
 of the frequency adjustment for increased precision.  Patches 9-12
 implement support for these changes.
Patch #1 is an unrelated fix for NAPI budget handling, needed in order for
 TX completion changes in the later patches to apply cleanly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Support increased precision frequency adjustment format (FP44) used
 by Medford2 adapters.
Signed-off-by: Laurence Evans <levans@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The time_format that we stash in the PTP data structure is never
 referenced, so we can remove it.  Instead, store the information needed
 to interpret sync event timestamps.
Also rolls in a couple of other related minor PTP fixes.

Based on patches by Bert Kenward <bkenward@solarflare.com> and Laurence
 Evans <levans@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support MC_CMD_PTP_OUT_GET_TIMESTAMP_CORRECTIONS_V2.  Extract general
 timestamp corrections in addition to PTP corrections.  Apply receive
 timestamp corrections for general datapath receive timestamping, and
 correspondingly for transmit.
Signed-off-by: Laurence Evans <levans@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use timestamp conversion function with correction to avoid duplicate
 correction handling.
Signed-off-by: Laurence Evans <levans@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We check the license for TX hardware timestamping capability.
The PTP probe will have enabled PTP sync events from the adapter.  If
 later, at TX queue init, it turns out we do not have the license, we
 don't need the sync events either.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For this we create and use one or more new TX queues on the PTP channel,
 and enable sync events for it.
Based on a patch by Martin Habets <mhabets@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>