of_iomap() can return NULL so that return needs to be checked and NULL
treated as failure. While at it also take care of the missing
of_node_put() in the error path.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit afa17a50 ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Inside m_can_chip_config(), when setting up the new value of the CCCR,
the CCCR_NISO bit is not cleared like the others, CCCR_TEST, CCCR_MON,
CCCR_BRSE and CCCR_FDOE, before checking the can.ctrlmode bits for
CAN_CTRLMODE_FD_NON_ISO.

This way once the controller was configured for CAN_CTRLMODE_FD_NON_ISO,
this mode could never be cleared again.

This fix is only relevant for controllers with version 3.1.x or 3.2.x.
Older versions do not support NISO.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The DMA logic in firmwares < v3.3.0 embedded in the PCAN-PCIe FD cards
family is not capable of handling a mix of 32-bit and 64-bit logical
addresses. If the board is equipped with 2 or 4 CAN ports, then such a
situation might lead to a PCIe Bus Error "Malformed TLP" packet
as well as "irq xx: nobody cared" issue.

This patch adds a workaround that requests only 32-bit DMA addresses
when these might be allocated outside of the 4 GB area.

This issue has been fixed in firmware v3.3.0 and next.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Prevent drivers from building on PPC32 if they use isa_bus_to_virt(),
isa_virt_to_bus(), or isa_page_to_bus(), which are not available and
thus cause build errors.

../drivers/net/ethernet/3com/3c515.c: In function 'corkscrew_open':
../drivers/net/ethernet/3com/3c515.c:824:9: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]

../drivers/net/ethernet/amd/lance.c: In function 'lance_rx':
../drivers/net/ethernet/amd/lance.c:1203:23: error: implicit declaration of function 'isa_bus_to_virt'; did you mean 'bus_to_virt'? [-Werror=implicit-function-declaration]

../drivers/net/ethernet/amd/ni65.c: In function 'ni65_init_lance':
../drivers/net/ethernet/amd/ni65.c:585:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]

../drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
../drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously only the neighbour state was checked to decide if an offloaded
entry should be removed. However, there can be situations when the entry
is dead but still marked as valid. This can lead to dead entries not
being removed from fw tables or even incorrect data being added.

Check the entry dead bit before deciding if it should be added to or
removed from fw neighbour tables.

Fixes: 8e6a9046 ("nfp: flower vxlan neighbour offload")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roopa Prabhu says:

====================
vxlan: fix default fdb entry user-space notify ordering/race

Problem:
In vxlan_newlink, a default fdb entry is added before register_netdev.
The default fdb creation function notifies user-space of the
fdb entry on the vxlan device which user-space does not know about yet.
(RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex).

This series fixes the user-space netlink notification ordering issue
with the following changes:
- decouple fdb notify from fdb create.
- Move fdb notify after register_netdev.
- modify rtnl_configure_link to allow configuring a link early.
- Call rtnl_configure_link in vxlan newlink handler to notify
userspace about the newlink before fdb notify and
hence avoiding the user-space race.
====================

Fixes: afbd8bae ("vxlan: add implicit fdb entry for default destination")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>

Problem:
In vxlan_newlink, a default fdb entry is added before register_netdev.
The default fdb creation function also notifies user-space of the
fdb entry on the vxlan device which user-space does not know about yet.
(RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex).

This patch fixes the user-space netlink notification ordering issue
with the following changes:
- decouple fdb notify from fdb create.
- Move fdb notify after register_netdev.
- Call rtnl_configure_link in vxlan newlink handler to notify
userspace about the newlink before fdb notify and
hence avoiding the user-space race.

Fixes: afbd8bae ("vxlan: add implicit fdb entry for default destination")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new option do_notify to vxlan_fdb_destroy to make
sending netlink notify optional. Used by a later patch.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Add new vxlan_fdb_alloc helper
- rename existing vxlan_fdb_create into vxlan_fdb_update:
        because it really creates or updates an existing
        fdb entry
- move new fdb creation into a separate vxlan_fdb_create

Main motivation for this change is to introduce the ability
to decouple vxlan fdb creation and notify, used in a later patch.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnl_configure_link sets dev->rtnl_link_state to
RTNL_LINK_INITIALIZED and unconditionally calls
__dev_notify_flags to notify user-space of dev flags.

current call sequence for rtnl_configure_link
rtnetlink_newlink
    rtnl_link_ops->newlink
    rtnl_configure_link (unconditionally notifies userspace of
                         default and new dev flags)

If a newlink handler wants to call rtnl_configure_link
early, we will end up with duplicate notifications to
user-space.

This patch fixes rtnl_configure_link to check rtnl_link_state
and call __dev_notify_flags with gchanges = 0 if already
RTNL_LINK_INITIALIZED.

Later in the series, this patch will help the following sequence
where a driver implementing newlink can call rtnl_configure_link
to initialize the link early.

makes the following call sequence work:
rtnetlink_newlink
    rtnl_link_ops->newlink (vxlan) -> rtnl_configure_link (initializes
                                                link and notifies
                                                user-space of default
                                                dev flags)
    rtnl_configure_link (updates dev flags if requested by user ifm
                         and notifies user-space of new dev flags)
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Got crash report with following backtrace:
BUG: unable to handle kernel paging request at ffff8801869daffe
RIP: 0010:[<ffffffff816429c4>]  [<ffffffff816429c4>] ip6_finish_output2+0x394/0x4c0
RSP: 0018:ffff880186c83a98  EFLAGS: 00010283
RAX: ffff8801869db00e ...
  [<ffffffff81644cdc>] ip6_finish_output+0x8c/0xf0
  [<ffffffff81644d97>] ip6_output+0x57/0x100
  [<ffffffff81643dc9>] ip6_forward+0x4b9/0x840
  [<ffffffff81645566>] ip6_rcv_finish+0x66/0xc0
  [<ffffffff81645db9>] ipv6_rcv+0x319/0x530
  [<ffffffff815892ac>] netif_receive_skb+0x1c/0x70
  [<ffffffffc0060bec>] atl1c_clean+0x1ec/0x310 [atl1c]
  ...

The bad access is in neigh_hh_output(), at skb->data - 16 (HH_DATA_MOD).
atl1c driver provided skb with no headroom, so 14 bytes (ethernet
header) got pulled, but then 16 are copied.

Reserve NET_SKB_PAD bytes headroom, like netdev_alloc_skb().

Compile tested only; I lack hardware.

Fixes: 7b701764 ("atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two scenarios that we will restore deleted records. The first is
when device down and up(or unmap/remap). In this scenario the new filter
mode is same with previous one. Because we get it from in_dev->mc_list and
we do not touch it during device down and up.

The other scenario is when a new socket join a group which was just delete
and not finish sending status reports. In this scenario, we should use the
current filter mode instead of restore old one. Here are 4 cases in total.

old_socket        new_socket       before_fix       after_fix
  IN(A)             IN(A)           ALLOW(A)         ALLOW(A)
  IN(A)             EX( )           TO_IN( )         TO_EX( )
  EX( )             IN(A)           TO_EX( )         ALLOW(A)
  EX( )             EX( )           TO_EX( )         TO_EX( )

Fixes: 24803f38 (igmp: do not remove igmp souce list info when set link down)
Fixes: 1666d49e (mld: do not remove mld souce list info when set link down)
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

free_irq() waits until all handlers for this IRQ have completed. As the
relevant handler (mv88e6xxx_g1_irq_thread_fn()) takes the chip's reg_lock
it might never return if the thread calling free_irq() holds this lock.

For the same reason kthread_cancel_delayed_work_sync() in the polling case
must not hold this lock.

Also first free the irq (or stop the worker respectively) such that
mv88e6xxx_g1_irq_thread_work() isn't called any more before the irq
mappings are dropped in mv88e6xxx_g1_irq_free_common() to prevent the
worker thread to call handle_nested_irq(0) which results in a NULL-pointer
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot caught a NULL deref [1], caused by skb_segment()

skb_segment() has many "goto err;" that assume the @err variable
contains -ENOMEM.

A successful call to __skb_linearize() should not clear @err,
otherwise a subsequent memory allocation error could return NULL.

While we are at it, we might use -EINVAL instead of -ENOMEM when
MAX_SKB_FRAGS limit is reached.

[1]
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
CPU: 0 PID: 13285 Comm: syz-executor3 Not tainted 4.18.0-rc4+ #146
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:tcp_gso_segment+0x3dc/0x1780 net/ipv4/tcp_offload.c:106
Code: f0 ff ff 0f 87 1c fd ff ff e8 00 88 0b fb 48 8b 75 d0 48 b9 00 00 00 00 00 fc ff df 48 8d be 90 00 00 00 48 89 f8 48 c1 e8 03 <0f> b6 14 08 48 8d 86 94 00 00 00 48 89 c6 83 e0 07 48 c1 ee 03 0f
RSP: 0018:ffff88019b7fd060 EFLAGS: 00010206
RAX: 0000000000000012 RBX: 0000000000000020 RCX: dffffc0000000000
RDX: 0000000000040000 RSI: 0000000000000000 RDI: 0000000000000090
RBP: ffff88019b7fd0f0 R08: ffff88019510e0c0 R09: ffffed003b5c46d6
R10: ffffed003b5c46d6 R11: ffff8801dae236b3 R12: 0000000000000001
R13: ffff8801d6c581f4 R14: 0000000000000000 R15: ffff8801d6c58128
FS:  00007fcae64d6700(0000) GS:ffff8801dae00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004e8664 CR3: 00000001b669b000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 tcp4_gso_segment+0x1c3/0x440 net/ipv4/tcp_offload.c:54
 inet_gso_segment+0x64e/0x12d0 net/ipv4/af_inet.c:1342
 inet_gso_segment+0x64e/0x12d0 net/ipv4/af_inet.c:1342
 skb_mac_gso_segment+0x3b5/0x740 net/core/dev.c:2792
 __skb_gso_segment+0x3c3/0x880 net/core/dev.c:2865
 skb_gso_segment include/linux/netdevice.h:4099 [inline]
 validate_xmit_skb+0x640/0xf30 net/core/dev.c:3104
 __dev_queue_xmit+0xc14/0x3910 net/core/dev.c:3561
 dev_queue_xmit+0x17/0x20 net/core/dev.c:3602
 neigh_hh_output include/net/neighbour.h:473 [inline]
 neigh_output include/net/neighbour.h:481 [inline]
 ip_finish_output2+0x1063/0x1860 net/ipv4/ip_output.c:229
 ip_finish_output+0x841/0xfa0 net/ipv4/ip_output.c:317
 NF_HOOK_COND include/linux/netfilter.h:276 [inline]
 ip_output+0x223/0x880 net/ipv4/ip_output.c:405
 dst_output include/net/dst.h:444 [inline]
 ip_local_out+0xc5/0x1b0 net/ipv4/ip_output.c:124
 iptunnel_xmit+0x567/0x850 net/ipv4/ip_tunnel_core.c:91
 ip_tunnel_xmit+0x1598/0x3af1 net/ipv4/ip_tunnel.c:778
 ipip_tunnel_xmit+0x264/0x2c0 net/ipv4/ipip.c:308
 __netdev_start_xmit include/linux/netdevice.h:4148 [inline]
 netdev_start_xmit include/linux/netdevice.h:4157 [inline]
 xmit_one net/core/dev.c:3034 [inline]
 dev_hard_start_xmit+0x26c/0xc30 net/core/dev.c:3050
 __dev_queue_xmit+0x29ef/0x3910 net/core/dev.c:3569
 dev_queue_xmit+0x17/0x20 net/core/dev.c:3602
 neigh_direct_output+0x15/0x20 net/core/neighbour.c:1403
 neigh_output include/net/neighbour.h:483 [inline]
 ip_finish_output2+0xa67/0x1860 net/ipv4/ip_output.c:229
 ip_finish_output+0x841/0xfa0 net/ipv4/ip_output.c:317
 NF_HOOK_COND include/linux/netfilter.h:276 [inline]
 ip_output+0x223/0x880 net/ipv4/ip_output.c:405
 dst_output include/net/dst.h:444 [inline]
 ip_local_out+0xc5/0x1b0 net/ipv4/ip_output.c:124
 ip_queue_xmit+0x9df/0x1f80 net/ipv4/ip_output.c:504
 tcp_transmit_skb+0x1bf9/0x3f10 net/ipv4/tcp_output.c:1168
 tcp_write_xmit+0x1641/0x5c20 net/ipv4/tcp_output.c:2363
 __tcp_push_pending_frames+0xb2/0x290 net/ipv4/tcp_output.c:2536
 tcp_push+0x638/0x8c0 net/ipv4/tcp.c:735
 tcp_sendmsg_locked+0x2ec5/0x3f00 net/ipv4/tcp.c:1410
 tcp_sendmsg+0x2f/0x50 net/ipv4/tcp.c:1447
 inet_sendmsg+0x1a1/0x690 net/ipv4/af_inet.c:798
 sock_sendmsg_nosec net/socket.c:641 [inline]
 sock_sendmsg+0xd5/0x120 net/socket.c:651
 __sys_sendto+0x3d7/0x670 net/socket.c:1797
 __do_sys_sendto net/socket.c:1809 [inline]
 __se_sys_sendto net/socket.c:1805 [inline]
 __x64_sys_sendto+0xe1/0x1a0 net/socket.c:1805
 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x455ab9
Code: 1d ba fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb b9 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fcae64d5c68 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007fcae64d66d4 RCX: 0000000000455ab9
RDX: 0000000000000001 RSI: 0000000020000200 RDI: 0000000000000013
RBP: 000000000072bea0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000014
R13: 00000000004c1145 R14: 00000000004d1818 R15: 0000000000000006
Modules linked in:
Dumping ftrace buffer:
   (ftrace buffer empty)

Fixes: ddff00d4 ("net: Move skb_has_shared_frag check out of GRE code and into segmentation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Example setup:
    host: ip -6 addr add dev eth1 2001:db8:104::4
           where eth1 is enslaved to a VRF

    switch: ip -6 ro add 2001:db8:104::4/128 dev br1
            where br1 only has an LLA

           ping6 2001:db8:104::4
           ssh   2001:db8:104::4

(NOTE: UDP works fine if the PKTINFO has the address set to the global
address and ifindex is set to the index of eth1 with a destination an
LLA).

For ICMP, icmp6_iif needs to be updated to check if skb->dev is an
L3 master. If it is then return the ifindex from rt6i_idev similar
to what is done for loopback.

For TCP, restore the original tcp_v6_iif definition which is needed in
most places and add a new tcp_v6_iif_l3_slave that considers the
l3_slave variability. This latter check is only needed for socket
lookups.

Fixes: 9ff74384 ("net: vrf: Handle ipv6 multicast and link-local addresses")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix following warning:
net/ipv4/bpfilter/sockopt.c:28:5: error: symbol 'bpfilter_ip_set_sockopt' redeclared with different type
net/ipv4/bpfilter/sockopt.c:34:5: error: symbol 'bpfilter_ip_get_sockopt' redeclared with different type
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The situation described in the comment can occur also with
PHY_IGNORE_INTERRUPT, therefore change the condition to include it.

Fixes: f555f34f ("net: phy: fix auto-negotiation stall due to unavailable interrupt")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
qed: Fix series II.

The patch series fixes few issues in the qed driver.

Please  consider applying it to 'net' branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

FW hsi contains 256 approximation buckets which are split in ramrod into
eight u32 values, but driver is using eight 'unsigned long' variables.

This patch fixes the mcast logic by making the API utilize u32.

Fixes: 83aeb933 ("qed*: Trivial modifications")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's a possible race where driver can read link status in mid-transition
and see that virtual-link is up yet speed is 0. Since in this
mid-transition we're guaranteed to see a mailbox from MFW soon, we can
afford to treat this as link down.

Fixes: cc875c2e ("qed: Add link support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Apparently, MFW publishes EEE capabilities even for Fiber-boards that don't
support them, and later since qed internally sets adv_caps it would cause
link-flap avoidance (LFA) to fail when driver would initiate the link.
This in turn delays the link, causing traffic to fail.

Driver has been modified to not to ask MFW for any EEE config if EEE isn't
to be enabled.

Fixes: 645874e5 ("qed: Add support for Energy efficient ethernet.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a missing rcu_read_unlock in the error path

Fixes: c95567c8 ("caif: added check for potential null return")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For some time now, if you load the bonding driver and configure bond
parameters via sysfs using minimal config options, such as specifying
nothing but the mode, relying on defaults for everything else, modes
that cannot use arp monitoring (802.3ad, balance-tlb, balance-alb) all
wind up with both arp_interval=0 (as it should be) and miimon=0, which
means the miimon monitor thread never actually runs. This is particularly
problematic for 802.3ad.

For example, from an LNST recipe I've set up:

$ modprobe bonding max_bonds=0"
$ echo "+t_bond0" > /sys/class/net/bonding_masters"
$ ip link set t_bond0 down"
$ echo "802.3ad" > /sys/class/net/t_bond0/bonding/mode"
$ ip link set ens1f1 down"
$ echo "+ens1f1" > /sys/class/net/t_bond0/bonding/slaves"
$ ip link set ens1f0 down"
$ echo "+ens1f0" > /sys/class/net/t_bond0/bonding/slaves"
$ ethtool -i t_bond0"
$ ip link set ens1f1 up"
$ ip link set ens1f0 up"
$ ip link set t_bond0 up"
$ ip addr add 192.168.9.1/24 dev t_bond0"
$ ip addr add 2002::1/64 dev t_bond0"

This bond comes up okay, but things look slightly suspect in
/proc/net/bonding/t_bond0 output:

$ grep -i mii /proc/net/bonding/t_bond0
MII Status: up
MII Polling Interval (ms): 0
MII Status: up
MII Status: up

Now, pull a cable on one of the ports in the bond, then reconnect it, and
you'll see:

Slave Interface: ens1f0
MII Status: down
Speed: 1000 Mbps
Duplex: full

I believe this became a major issue as of commit 4d2c0cda, which for
802.3ad bonds, sets slave->link = BOND_LINK_DOWN, with a comment about
relying on link monitoring via miimon to set it correctly, but since the
miimon work queue never runs, the link just stays marked down.

If we simply tweak bond_option_mode_set() slightly, we can check for the
non-arp modes having no miimon value set, and insert BOND_DEFAULT_MIIMON,
which gets things back in full working order. This problem exists as far
back as 4.14, and might be worth fixing in all stable trees since, though
the work-around is to simply specify an miimon value yourself.
Reported-by: Bob Ball <ball@umich.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2018-07-18

The following series provides fixes to mlx5 core and net device driver.

Please pull and let me know if there's any problem.

For -stable v4.7
    net/mlx5e: Don't allow aRFS for encapsulated packets
    net/mlx5e: Fix quota counting in aRFS expire flow

For -stable v4.15
    net/mlx5e: Only allow offloading decap egress (egdev) flows
    net/mlx5e: Refine ets validation function
    net/mlx5: Adjust clock overflow work period

For -stable v4.17
    net/mlx5: E-Switch, UBSAN fix undefined behavior in mlx5_eswitch_mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-07-20

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix in BPF Makefile to detect llvm-objcopy in a more robust way which is
   needed for pahole's BTF converter and minor UAPI tweaks in BTF_INT_BITS()
   to shrink the mask before eventual UAPI freeze, from Martin.

2) Fix a segfault in bpftool when prog pin id has no further arguments such
   as id value or file specified, from Taeung.

3) Fix powerpc JIT handling of XADD which has jumps to exit path that would
   potentially bypass verifier expectations e.g. with subprog calls. Also add
   a test case to make sure XADD is not mangling src/dst register, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code does not check sk->sk_shutdown & RCV_SHUTDOWN.
tls_sw_recvmsg may return a positive value in the case where bytes have
already been copied when the socket is shutdown. sk->sk_err has been
cleared, causing the tls_wait_data to hang forever on a subsequent
invocation. Checking sk->sk_shutdown & RCV_SHUTDOWN, as in tcp_recvmsg,
fixes this problem.

Fixes: c46234eb ("tls: RX path for ktls")
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
fix DCTCP ECE Ack series

This patch set address that the existing DCTCP implementation does not
fully implement the ACK policy specified in the RFC. This improves
the responsiveness of CE status change particularly on flows with
small inflight.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Per DCTCP RFC8257 (Section 3.2) the ACK reflecting the CE status change
has to be sent immediately so the sender can respond quickly:

""" When receiving packets, the CE codepoint MUST be processed as follows:

   1.  If the CE codepoint is set and DCTCP.CE is false, set DCTCP.CE to
       true and send an immediate ACK.

   2.  If the CE codepoint is not set and DCTCP.CE is true, set DCTCP.CE
       to false and send an immediate ACK.
"""

Previously DCTCP implementation may continue to delay the ACK. This
patch fixes that to implement the RFC by forcing an immediate ACK.

Tested with this packetdrill script provided by Larry Brakmo

0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0

0.100 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
0.100 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
0.110 < [ect0] . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
   +0 setsockopt(4, SOL_SOCKET, SO_DEBUG, [1], 4) = 0

0.200 < [ect0] . 1:1001(1000) ack 1 win 257
0.200 > [ect01] . 1:1(0) ack 1001

0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 1:2(1) ack 1001

0.200 < [ect0] . 1001:2001(1000) ack 2 win 257
+0.005 < [ce] . 2001:3001(1000) ack 2 win 257

+0.000 > [ect01] . 2:2(0) ack 2001
// Previously the ACK below would be delayed by 40ms
+0.000 > [ect01] E. 2:2(0) ack 3001

+0.500 < F. 9501:9501(0) ack 4 win 257
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when a DCTCP receiver delays an ACK and receive a
data packet with a different CE mark from the previous one's, it
sends two immediate ACKs acking previous and latest sequences
respectly (for ECN accounting).

Previously sending the first ACK may mark off the delayed ACK timer
(tcp_event_ack_sent). This may subsequently prevent sending the
second ACK to acknowledge the latest sequence (tcp_ack_snd_check).
The culprit is that tcp_send_ack() assumes it always acknowleges
the latest sequence, which is not true for the first special ACK.

The fix is to not make the assumption in tcp_send_ack and check the
actual ack sequence before cancelling the delayed ACK. Further it's
safer to pass the ack sequence number as a local variable into
tcp_send_ack routine, instead of intercepting tp->rcv_nxt to avoid
future bugs like this.
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor and create helpers to send the special ACK in DCTCP.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I noticed the "--version" option of the llvm-objcopy command has recently
disappeared from the master llvm branch.  It is currently used as a BTF
support test in tools/testing/selftests/bpf/Makefile.

This patch replaces it with "--help" which should be
less error prone in the future.

Fixes: c0fa1b6c ("bpf: btf: Add BTF tests")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

This patch shrinks the BTF_INT_BITS() mask.  The current
btf_int_check_meta() ensures the nr_bits of an integer
cannot exceed 64.  Hence, it is mostly an uapi cleanup.

The actual btf usage (i.e. seq_show()) is also modified
to use u8 instead of u16.  The verification (e.g. btf_int_check_meta())
path stays as is to deal with invalid BTF situation.

Fixes: 69b693f0 ("bpf: btf: Introduce BPF Type Format (BTF)")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Arguments of 'pin' subcommand should be checked
at the very beginning of do_pin_any().
Otherwise segfault errors can occur when using
'map pin' or 'prog pin' commands, so fix it.

  # bpftool prog pin id
  Segmentation fault

Fixes: 71bb428f ("tools: bpf: add bpftool")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reported-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Taeung Song <treeze.taeung@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The calculation of "wqe_size" is not correct when the tx queue is busy in
hinic_xmit_frame().

When there are no free WQEs, the tx flow will unmap the skb buffer, then
ring the doobell for the pending packets. But the "wqe_size" which used
to calculate the doorbell address is not correct. The wqe size should be
cleared to 0, otherwise, it will cause a doorbell error.

This patch fixes the problem.
Reported-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the warning below by calling the ptr_ring_consume_bh,
which uses spin_[un]lock_bh.

[  179.064300] ================================
[  179.069073] WARNING: inconsistent lock state
[  179.073846] 4.18.0-rc2+ #18 Not tainted
[  179.078133] --------------------------------
[  179.082907] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[  179.089637] swapper/21/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
[  179.095478] 00000000963d1995 (&(&r->consumer_lock)->rlock){+.?.}, at:
__page_pool_empty_ring+0x61/0x100
[  179.105988] {SOFTIRQ-ON-W} state was registered at:
[  179.111443]   _raw_spin_lock+0x35/0x50
[  179.115634]   __page_pool_empty_ring+0x61/0x100
[  179.120699]   page_pool_destroy+0x32/0x50
[  179.125204]   mlx5e_free_rq+0x38/0xc0 [mlx5_core]
[  179.130471]   mlx5e_close_channel+0x20/0x120 [mlx5_core]
[  179.136418]   mlx5e_close_channels+0x26/0x40 [mlx5_core]
[  179.142364]   mlx5e_close_locked+0x44/0x50 [mlx5_core]
[  179.148509]   mlx5e_close+0x42/0x60 [mlx5_core]
[  179.153936]   __dev_close_many+0xb1/0x120
[  179.158749]   dev_close_many+0xa2/0x170
[  179.163364]   rollback_registered_many+0x148/0x460
[  179.169047]   rollback_registered+0x56/0x90
[  179.174043]   unregister_netdevice_queue+0x7e/0x100
[  179.179816]   unregister_netdev+0x18/0x20
[  179.184623]   mlx5e_remove+0x2a/0x50 [mlx5_core]
[  179.190107]   mlx5_remove_device+0xe5/0x110 [mlx5_core]
[  179.196274]   mlx5_unregister_interface+0x39/0x90 [mlx5_core]
[  179.203028]   cleanup+0x5/0xbfc [mlx5_core]
[  179.208031]   __x64_sys_delete_module+0x16b/0x240
[  179.213640]   do_syscall_64+0x5a/0x210
[  179.218151]   entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  179.224218] irq event stamp: 334398
[  179.228438] hardirqs last  enabled at (334398): [<ffffffffa511d8b7>]
rcu_process_callbacks+0x1c7/0x790
[  179.239178] hardirqs last disabled at (334397): [<ffffffffa511d872>]
rcu_process_callbacks+0x182/0x790
[  179.249931] softirqs last  enabled at (334386): [<ffffffffa509732e>] irq_enter+0x5e/0x70
[  179.259306] softirqs last disabled at (334387): [<ffffffffa509741c>] irq_exit+0xdc/0xf0
[  179.268584]
[  179.268584] other info that might help us debug this:
[  179.276572]  Possible unsafe locking scenario:
[  179.276572]
[  179.283877]        CPU0
[  179.286954]        ----
[  179.290033]   lock(&(&r->consumer_lock)->rlock);
[  179.295546]   <Interrupt>
[  179.298830]     lock(&(&r->consumer_lock)->rlock);
[  179.304550]
[  179.304550]  *** DEADLOCK ***

Fixes: ff7d6b27 ("page_pool: refurbish version of page_pool code")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
This set adds a ppc64 JIT fix for xadd as well as a missing test
case for verifying whether xadd messes with src/dst reg. Thanks!
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

We currently do not have such a test case in test_verifier selftests
but it's important to test under bpf_jit_enable=1 to make sure JIT
implementations do not mistakenly mess with src/dst reg for xadd/{w,dw}.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

None of the JITs is allowed to implement exit paths from the BPF
insn mappings other than BPF_JMP | BPF_EXIT. In the BPF core code
we have a couple of rewrites in eBPF (e.g. LD_ABS / LD_IND) and
in eBPF to cBPF translation to retain old existing behavior where
exceptions may occur; they are also tightly controlled by the
verifier where it disallows some of the features such as BPF to
BPF calls when legacy LD_ABS / LD_IND ops are present in the BPF
program. During recent review of all BPF_XADD JIT implementations
I noticed that the ppc64 one is buggy in that it contains two
jumps to exit paths. This is problematic as this can bypass verifier
expectations e.g. pointed out in commit f6b1b3bf ("bpf: fix
subprog verifier bypass by div/mod by 0 exception"). The first
exit path is obsoleted by the fix in ca369602 ("bpf: allow xadd
only on aligned memory") anyway, and for the second one we need to
do a fetch, add and store loop if the reservation from lwarx/ldarx
was lost in the meantime.

Fixes: 156d0e29 ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF")
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Tested-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Pull sound fixes from Takashi Iwai:
 "A rawmidi race fix and three trivial HD-audio quirks"

* tag 'sound-4.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - Yet another Clevo P950 quirk entry
  ALSA: rawmidi: Change resized buffers atomically
  ALSA: hda/realtek - Add Panasonic CF-SZ6 headset jack quirk
  ALSA: hda: add mute led support for HP ProBook 455 G5

Pull crypto fix from Herbert Xu:
 "This fixes an allocation error-path bug in af_alg discovered by
  syzkaller"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: af_alg - Initialize sg_num_bytes in error code path