Map a DSA structure over the 48-byte control block that will hold
skb info on transmit and receive. This is only for use within the DSA
processing layer (e.g. communicating between DSA core and tagger) and
not for passing info around with other layers such as the master net
device.

Also add a DSA_SKB_CB_PRIV() macro which retrieves a pointer to the
space up to 48 bytes that the DSA structure does not use. This space can
be used for drivers to add their own private info.

One use is for the PTP timestamping code path. When cloning a skb,
annotate the original with a pointer to the clone, which the driver can
then find easily and place the timestamp to. This avoids the need of a
separate queue to hold clones and a way to match an original to a cloned
skb.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Frames get processed by DSA and redirected to switch port net devices
based on the ETH_P_XDSA multiplexed packet_type handler found by the
network stack when calling eth_type_trans().

The running assumption is that once the DSA .rcv function is called, DSA
is always able to decode the switch tag in order to change the skb->dev
from its master.

However there are tagging protocols (such as the new DSA_TAG_PROTO_SJA1105,
user of DSA_TAG_PROTO_8021Q) where this assumption is not completely
true, since switch tagging piggybacks on the absence of a vlan_filtering
bridge. Moreover, management traffic (BPDU, PTP) for this switch doesn't
rely on switch tagging, but on a different mechanism. So it would make
sense to at least be able to terminate that.

Having DSA receive traffic it can't decode would put it in an impossible
situation: the eth_type_trans() function would invoke the DSA .rcv(),
which could not change skb->dev, then eth_type_trans() would be invoked
again, which again would call the DSA .rcv, and the packet would never
be able to exit the DSA filter and would spiral in a loop until the
whole system dies.

This happens because eth_type_trans() doesn't actually look at the skb
(so as to identify a potential tag) when it deems it as being
ETH_P_XDSA. It just checks whether skb->dev has a DSA private pointer
installed (therefore it's a DSA master) and that there exists a .rcv
callback (everybody except DSA_TAG_PROTO_NONE has that). This is
understandable as there are many switch tags out there, and exhaustively
checking for all of them is far from ideal.

The solution lies in introducing a filtering function for each tagging
protocol. In the absence of a filtering function, all traffic is passed
to the .rcv DSA callback. The tagging protocol should see the filtering
function as a pre-validation that it can decode the incoming skb. The
traffic that doesn't match the filter will bypass the DSA .rcv callback
and be left on the master netdevice, which wasn't previously possible.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch provides generic DSA code for using VLAN (802.1Q) tags for
the same purpose as a dedicated switch tag for injection/extraction.
It is based on the discussions and interest that has been so far
expressed in https://www.spinics.net/lists/netdev/msg556125.html.

Unlike all other DSA-supported tagging protocols, CONFIG_NET_DSA_TAG_8021Q
does not offer a complete solution for drivers (nor can it). Instead, it
provides generic code that driver can opt into calling:
- dsa_8021q_xmit: Inserts a VLAN header with the specified contents.
  Can be called from another tagging protocol's xmit function.
  Currently the LAN9303 driver is inserting headers that are simply
  802.1Q with custom fields, so this is an opportunity for code reuse.
- dsa_8021q_rcv: Retrieves the TPID and TCI from a VLAN-tagged skb.
  Removing the VLAN header is left as a decision for the caller to make.
- dsa_port_setup_8021q_tagging: For each user port, installs an Rx VID
  and a Tx VID, for proper untagged traffic identification on ingress
  and steering on egress. Also sets up the VLAN trunk on the upstream
  (CPU or DSA) port. Drivers are intentionally left to call this
  function explicitly, depending on the context and hardware support.
  The expected switch behavior and VLAN semantics should not be violated
  under any conditions. That is, after calling
  dsa_port_setup_8021q_tagging, the hardware should still pass all
  ingress traffic, be it tagged or untagged.

For uniformity with the other tagging protocols, a module for the
dsa_8021q_netdev_ops structure is registered, but the typical usage is
to set up another tagging protocol which selects CONFIG_NET_DSA_TAG_8021Q,
and calls the API from tag_8021q.h. Null function definitions are also
provided so that a "depends on" is not forced in the Kconfig.

This tagging protocol only works when switch ports are standalone, or
when they are added to a VLAN-unaware bridge. It will probably remain
this way for the reasons below.

When added to a bridge that has vlan_filtering 1, the bridge core will
install its own VLANs and reset the pvids through switchdev. For the
bridge core, switchdev is a write-only pipe. All VLAN-related state is
kept in the bridge core and nothing is read from DSA/switchdev or from
the driver. So the bridge core will break this port separation because
it will install the vlan_default_pvid into all switchdev ports.

Even if we could teach the bridge driver about switchdev preference of a
certain vlan_default_pvid (task difficult in itself since the current
setting is per-bridge but we would need it per-port), there would still
exist many other challenges.

Firstly, in the DSA rcv callback, a driver would have to perform an
iterative reverse lookup to find the correct switch port. That is
because the port is a bridge slave, so its Rx VID (port PVID) is subject
to user configuration. How would we ensure that the user doesn't reset
the pvid to a different value (which would make an O(1) translation
impossible), or to a non-unique value within this DSA switch tree (which
would make any translation impossible)?

Finally, not all switch ports are equal in DSA, and that makes it
difficult for the bridge to be completely aware of this anyway.
The CPU port needs to transmit tagged packets (VLAN trunk) in order for
the DSA rcv code to be able to decode source information.
But the bridge code has absolutely no idea which switch port is the CPU
port, if nothing else then just because there is no netdevice registered
by DSA for the CPU port.
Also DSA does not currently allow the user to specify that they want the
CPU port to do VLAN trunking anyway. VLANs are added to the CPU port
using the same flags as they were added on the user port.

So the VLANs installed by dsa_port_setup_8021q_tagging per driver
request should remain private from the bridge's and user's perspective,
and should not alter the VLAN semantics observed by the user.

In the current implementation a VLAN range ending at 4095 (VLAN_N_VID)
is reserved for this purpose. Each port receives a unique Rx VLAN and a
unique Tx VLAN. Separate VLANs are needed for Rx and Tx because they
serve different purposes: on Rx the switch must process traffic as
untagged and process it with a port-based VLAN, but with care not to
hinder bridging. On the other hand, the Tx VLAN is where the
reachability restrictions are imposed, since by tagging frames in the
xmit callback we are telling the switch onto which port to steer the
frame.

Some general guidance on how this support might be employed for
real-life hardware (some comments made by Florian Fainelli):

- If the hardware supports VLAN tag stacking, it should somehow back
  up its private VLAN settings when the bridge tries to override them.
  Then the driver could re-apply them as outer tags. Dedicating an outer
  tag per bridge device would allow identical inner tag VID numbers to
  co-exist, yet preserve broadcast domain isolation.

- If the switch cannot handle VLAN tag stacking, it should disable this
  port separation when added as slave to a vlan_filtering bridge, in
  that case having reduced functionality.

- Drivers for old switches that don't support the entire VLAN_N_VID
  range will need to rework the current range selection mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is needed so that the newly introduced tag_8021q may access these
core DSA functions when built as a module.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows the driver to perform some manipulations of its own during
setup, using generic switchdev calls. Having the notifiers registered at
setup time is important because otherwise any switchdev transaction
emitted during this time would be ignored (dispatched to an empty call
chain).

One current usage scenario is for the driver to request DSA to set up
802.1Q based switch tagging for its ports.

There is no danger for the driver setup code to start racing now with
switchdev events emitted from the network stack (such as bridge core)
even if the notifier is registered earlier. This is because the network
stack needs a net_device as a vehicle to perform switchdev operations,
and the slave net_devices are registered later than the core driver
setup anyway (ds->ops->setup in dsa_switch_setup vs dsa_port_setup).

Luckily DSA doesn't need a net_device to carry out switchdev callbacks,
and therefore drivers shouldn't assume either that net_devices are
available at the time their switchdev callbacks get invoked.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>-
Signed-off-by: David S. Miller <davem@davemloft.net>

The Marvell SOHO switches have several ways to access the internal
registers. One of them being the System Management Interface (SMI),
using the MDC and MDIO pins, with direct and indirect variants.

In preparation for adding support for other register accesses, move
the SMI code into its own files. At the same time, refine the code
to make it clear that the indirect variant is implemented using the
direct variant accessing only two registers for command and data.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

===================
net: act_police offload support

this set starts by converting cls_matchall to the new flow offload
infrastructure. It so happens that all drivers implementing cls_matchall
offload today also offload cls_flower, so its a little easier for
them to handle the actions in unified flow_rule format, even though
in cls_matchall there is no flow to speak of. If a driver ever appears
which would prefer the old, direct access to TC exts, we can add the
pointer in the offload structure back and support both.

Next the act_police is added to actions supported by flow offload API.

NFP support for act_police offload is added as the final step.  The flower
firmware is configured to perform TX rate limiting in a way which matches
act_police's behaviour.  It does not use DMA.IN back pressure, and
instead	drops packets after they had been already DMAed into the NIC.
IOW it uses our standard traffic policing implementation, future patches
will extend it to other ports and traffic directions.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add stats request function that sends a stats request message to hw for
a specific police-filter. Process stats reply from hw and update the
stored qos structure.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add install and remove offload functionality for qos offloads. We
first check that a police filter can be implemented by the VF rate
limiting feature in hw, then we install the filter via the qos
infrastructure. Finally we implement the mechanism for removing
these types of filters.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce matchall filter offload infrastructure that is needed to
offload qos features like policing. Subsequent patches will make
use of police-filters for ingress rate limiting.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some actions like the police action are stateful and could share state
between devices. This is incompatible with offloading to multiple devices
and drivers might want to test for shared blocks when offloading.
Store a pointer to the tcf_block structure in the tc_cls_common_offload
structure to allow drivers to determine when offloads apply to a shared
block.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the stats_update callback for the police action that
will be used by drivers for hardware offload.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a new command for matchall classifiers that allows hardware
to update statistics.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add police action to the hardware intermediate representation which
would subsequently allow it to be used by drivers for offload.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move tcf_police_params, tcf_police and tc_police_compat structures to a
header. Making them usable to other code for example drivers that would
offload police actions to hardware.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cleanup unused functions and variables after porting to the newer
intermediate representation.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Updates dsa hardware switch handling infrastructure to use the newer
intermediate representation for flow actions in matchall offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Updates the Mellanox spectrum driver to use the newer intermediate
representation for flow actions in matchall offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extends matchall offload to make use of the hardware intermediate
representation. More specifically, this patch moves the native TC
actions in cls_matchall offload to the newer flow_action
representation. This ultimately allows us to avoid a direct
dependency on native TC actions for matchall.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add sample action to the hardware intermediate representation model which
would subsequently allow it to be used by drivers for offload.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Petr Štetiar says:

====================
of_net: Add NVMEM support to of_get_mac_address

this patch series is a continuation of my previous attempt[1], where I've
tried to wire MTD layer into of_get_mac_address, so it would be possible to
load MAC addresses from various NVMEMs as EEPROMs etc.

Predecessor of this patch which used directly MTD layer has originated in
OpenWrt some time ago and supports already about 497 use cases in 357
device tree files.

During the review process of my 1st attempt I was told, that I shouldn't be
using MTD directly, but that I should rather use new NVMEM subsystem and
during the review process of v2 I was told, that I should handle
EPROBE_DEFFER error as well, during the review process of v3 I was told,
that returning pointer/NULL/ERR_PTR is considered as wrong API design, so
this v4 patch series tries to accommodate all this previous remarks.

First patch is wiring NVMEM support directly into of_get_mac_address as
it's obvious, that adding support for NVMEM into every other driver would
mean adding a lot of repetitive code. This patch allows us to configure MAC
addresses in various devices like ethernet and wireless adapters directly
from of_get_mac_address, which is used by quite a lot of drivers in the
tree already.

Second patch is simply updating documentation with NVMEM bits, and cleaning
up all current binding documentation referencing any of the MAC address
related properties.

Third and fourth patches are simply removing duplicate NVMEM code which is
no longer needed as the first patch has wired NVMEM support directly into
of_get_mac_address.

Patches 5-10 are converting all current users of of_get_mac_address to the
new ERR_PTR encoded error value, as of_get_mac_address could now return
valid pointer, NULL and ERR_PTR.

Just for a better picture, this patch series and one simple patch[2] on top
of it, allows me to configure 8Devices Carambola2 board's MAC addresses
with following DTS (simplified):

 &spi {
 	flash@0 {
 		partitions {
			art: partition@ff0000 {
				label = "art";
				reg = <0xff0000 0x010000>;
				read-only;

				nvmem-cells {
					compatible = "nvmem-cells";
					#address-cells = <1>;
					#size-cells = <1>;

					eth0_addr: eth-mac-addr@0 {
						reg = <0x0 0x6>;
					};

					eth1_addr: eth-mac-addr@6 {
						reg = <0x6 0x6>;
					};

					wmac_addr: wifi-mac-addr@1002 {
						reg = <0x1002 0x6>;
					};
				};
			};
		};
	};
 };

 &eth0 {
	nvmem-cells = <&eth0_addr>;
	nvmem-cell-names = "mac-address";
 };

 &eth1 {
	nvmem-cells = <&eth1_addr>;
	nvmem-cell-names = "mac-address";
 };

 &wmac {
	nvmem-cells = <&wmac_addr>;
	nvmem-cell-names = "mac-address";
 };

1. https://patchwork.ozlabs.org/patch/1086628/
2. https://patchwork.ozlabs.org/patch/890738/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There was NVMEM support added to of_get_mac_address, so it could now return
ERR_PTR encoded error values, so we need to adjust all current users of
of_get_mac_address to this new fact.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

There was NVMEM support added to of_get_mac_address, so it could now return
ERR_PTR encoded error values, so we need to adjust all current users of
of_get_mac_address to this new fact.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

There was NVMEM support added to of_get_mac_address, so it could now return
ERR_PTR encoded error values, so we need to adjust all current users of
of_get_mac_address to this new fact.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

There was NVMEM support added to of_get_mac_address, so it could now return
ERR_PTR encoded error values, so we need to adjust all current users of
of_get_mac_address to this new fact.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

There was NVMEM support added to of_get_mac_address, so it could now return
ERR_PTR encoded error values, so we need to adjust all current users of
of_get_mac_address to this new fact.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

There was NVMEM support added directly to of_get_mac_address, and it uses
nvmem_get_mac_address under the hood, so we can remove it. As
of_get_mac_address can now return ERR_PTR encoded error values, adjust to
that as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

There was NVMEM support added directly to of_get_mac_address, and it uses
nvmem_get_mac_address under the hood, so we can remove it. As
of_get_mac_address can now return ERR_PTR encoded error values, adjust to
that as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

As of_get_mac_address now supports NVMEM under the hood, we need to update
the bindings documentation with the new nvmem-cell* properties, which would
mean copy&pasting a lot of redundant information to every binding
documentation currently referencing some of the MAC address properties.

So I've just removed all the references to the optional MAC address
properties and replaced them with the small note referencing
net/ethernet.txt file.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many embedded devices have information such as MAC addresses stored
inside NVMEMs like EEPROMs and so on. Currently there are only two
drivers in the tree which benefit from NVMEM bindings.

Adding support for NVMEM into every other driver would mean adding a lot
of repetitive code. This patch allows us to configure MAC addresses in
various devices like ethernet and wireless adapters directly from
of_get_mac_address, which is already used by almost every driver in the
tree.

Predecessor of this patch which used directly MTD layer has originated
in OpenWrt some time ago and supports already about 497 use cases in 357
device tree files.

Cc: Alban Bedel <albeu@free.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Driver updates.

This patch series adds some extended statistics available with the new
firmware interface, package version from firmware, aRFS support on
57500 chips, new PCI IDs, and some miscellaneous fixes and improvements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

0x1806 and 0x1752 are VF variant and PF variant of the 57500 chip
family.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set RSS ring table index of the RFS destination ring for the NTUPLE
filters on 57500 chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Query support for the aRFS ring table index in the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_need_reserve_rings() determines if any resources have changed and
requires new reservation with firmware.  The NQ checking is currently
just an approximation.  Improve the NQ checking logic to make it
accurate.  NQ reservation is only needed on 57500 PFs.  This fix will
eliminate unnecessary reservations and will reduce NQ reservations
when some NQs have been released on 57500 PFs.

Fixes: c0b8cda0 ("bnxt_en: Fix NQ/CP rings accounting on the new 57500 chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In newer firmware, the context memory for MR (Memory Region)
and AH (Address Handle) to support RDMA are specified separately.
Modify driver to specify and allocate the 2 context memory types
separately when supported by the firmware.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently driver hard code Clause 45 based on speed supported by the
PHY. Instead read the clause type from the PHY ID provided as input
to the mdio ioctl.

Fixes: 0ca12be9 ("bnxt_en: Add support for mdio read/write to external PHY")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HWRM_VER_GET firmware command returns package name that is running
actively on the adapter.  Use this version instead of parsing from
the package log in NVRAM.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newer firmware now advertises the capability for extended stats
support.  Check the new capability in addition to the existing
version check.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Gather periodic PCIe statistics for ethtool -S.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>