It enhances the driver for FTDI-based USB serial adapters to recognize and
support Northern Digital Inc (NDI) measurement equipment. NDI has been
providing this patch for various kernel flavors for several years and we would
like to see these changes built in to the driver so that our equipement works
without the need for customers to patch the kernel themselves.

The patch makes small modifications to 2 files: ./drivers/usb/serial/ftdi_sio.c
and ./drivers/usb/serial/ftdi_sio.h. It accomplishes 3 things:

1. Define the VID and PIDs to allow the driver to recognize the NDI devices.
2. Map the 19200 baud rate setting to our higher baud rate of 1.2Mb
   We would have chosen to map 38400 to the higher rate, similar to what
   several other vendors have done, but some of our legacy customers actually
   use 38400, therefore we remap 19200 to the higher rate.
3. We set the default transmit latency in the FTDI chip to 1ms for our devices.
   Our devices are typically polled at 60Hz and the default ftdi latency
   seriously affects turn-around time and results in missed data frames. We
   have created a modprobe option that allows this setting to be increased.
   This has proven necessary particularly in some virtualized environments.
Signed-off-by: Martin P. Geleynse <mgeleyns@ndigital.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This reverts commit cc71329b, so that
Red Hat machines can boot properly.  It seems that the Red Hat initrd
code tries to watch the /proc/bus/usb/devices file to monitor usb
devices showing up.  While this task is prone to lots of races and does
not show the true state of the system, they seem to like it.

So for now, don't move this option under the EMBEDDED config option.


Cc: Scott James Remnant <scott@canonical.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Jeff Chua <jeff.chua.linux@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix usb.h kernel-doc warnings:

Warning(include/linux/usb.h:918): Excess struct/union/enum/typedef member 'nodename' description in 'usb_device_driver'
Warning(include/linux/usb.h:939): No description found for parameter 'nodename'
Warning(include/linux/usb.h:1219): No description found for parameter 'sg'
Warning(include/linux/usb.h:1219): No description found for parameter 'num_sgs'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The reworked Ethernet gadget has an RNDIS interop problem when used
with the CDC subset driver ... e.g. on PXA 2xx and 3xx hardware,
which currently has a hard time talking to MS-Windows hosts.

The issue is that Microsoft requires USB_CLASS_COMM.  Fix by tweaking
the CDC subset driver to not switch to USB_CLASS_VENDOR_SPEC if RNDIS
is used in some other device configuration.

[ UPDATED:  some "statements" were comma-terminated; fix that. ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Aric Blumer <aric@sdgsystems.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

It seems an USB device with vendor id 0403 and product code FB80 has an
FTDI serial io chip as well: http://ftdichip.com/Drivers/D2XX.htm
This device in fact is a true random generantor by comsci:
http://comscire.com/Products/R2000KU/
So the following patch should add support for this device if I am
correct. Not tested as I do not own this device (I would like support in
the kernel so that my entropybroker application (which distributes
entrop data (random values) between servers and clients)).


From: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The commit 335f8514 introduced a
regression which stopped usb consoles from working correctly as a
kernel boot console as well as interactive login device.

The addition of the serial_close() which in turn calls
tty_port_close_start() will change the reference count of port.count
and warn about it.  The usb console code had previously incremented
the port.count to indicate it was making use of the device as a
console and the forced change causes a double open on the usb device
which leads to a non obvious kernel oops later on when the tty is
freed.

To fix the problem instead make use of port->console to track if the
port is in fact an active console port to avoid double initialization
of the usb serial device.  The port.count is incremented and
decremented only with in the scope of usb_console_setup() for the
purpose of the low level driver initialization.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Added descriptions (for WIRELESS_CONTROLLER and MISC) were taken from
the usb-devices script now included in usbutils.

Also sort the classes in the same order as in include/linux/usb/ch9.h
for easier comparison for future updates.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes a memory leak in devio.c::processcompl

If writing to user space fails the packet must be discarded, as it
already has been removed from the queue of completed packets.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1257) revises the way ehci-hcd detects STALLs.  The
logic is a little peculiar because there's no hardware status bit
specifically meant to indicate a STALL.  You just have to guess that a
STALL was received if the BABBLE bit (which is fatal) isn't set and
the transfer stopped before all its retries were used up.

The existing code doesn't do this properly, because it tests for MMF
(Missed MicroFrame) and DBE (Data Buffer Error) before testing the
retry counter.  Thus, if a transaction gets either MMF or DBE the
corresponding flag is set and the transaction is retried.  If the
second attempt receives a STALL then -EPIPE is the correct return
value.  But the existing code would see the MMF or DBE flag instead
and return -EPROTO, -ENOSR, or -ECOMM.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1256) changes ehci-hcd and all the other drivers in the
EHCI family to make use of the new clear_tt_buffer callbacks.  When a
Clear-TT-Buffer request is in progress for a QH, the QH is not allowed
to be linked into the async schedule until the request is finished.
At that time, if there are any URBs queued for the QH, it is linked
into the async schedule.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1255) updates the interface for calling
usb_hub_clear_tt_buffer().  Even the name of the function is changed!

When an async URB (i.e., Control or Bulk) going through a high-speed
hub to a non-high-speed device is cancelled or fails, the hub's
Transaction Translator buffer may be left busy still trying to
complete the transaction.  The buffer has to be cleared; that's what
usb_hub_clear_tt_buffer() does.

It isn't safe to send any more URBs to the same endpoint until the TT
buffer is fully clear.  Therefore the HCD needs to be told when the
Clear-TT-Buffer request has finished.  This patch adds a callback
method to struct hc_driver for that purpose, and makes the hub driver
invoke the callback at the proper time.

The patch also changes a couple of names; "hub_tt_kevent" and
"tt.kevent" now look rather antiquated.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Used by Virgin Mobile with the Broadband2Go service, for example.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch introduces a work around for cdc-acm devices which are
low speed contrary to the specification, which requires bulk endpoints
which are banned in low speed and converted by usbcore to virtual
interrupt endpoints if they are used nevertheless.
Signed-off-by: Arseniy Lartsev <ars3n@yandex.ru>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Get rid of some obnoxious and inappropriate messaging, mostly on
DaVinci, when usbcore tries to autosuspend a root hub if just a
mini/micro-A connector is connected.  Symptom: endless stream of
messages reading like:

 musb_bus_suspend 2221: trying to suspend as a_wait_vrise is_active=1

Improve that musb bus suspend primitive a bit.  Take advantage of
this call to update the OTG state machine if appropriate, moving
the device out of the A_WAIT_VRISE state.  There's basically no
timer for that state transition just now, except with tusb6010;
that can make trouble.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix config-dependent compiler warning:

  CC      drivers/usb/gadget/pxa25x_udc.o
drivers/usb/gadget/pxa25x_udc.c: In function 'pxa25x_udc_irq':
drivers/usb/gadget/pxa25x_udc.c:1806: warning: array subscript is above array bounds
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Use gpio_is_valid instead of assuming that every GPIO
number != 0 is valid while 0 is not.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Numbering for GPIOs on the pcf857x chips on the dm644x EVM board
changed when DaVinci chips with more GPIOs were supported.  Update
the GPIO number used for nVBUS_DRV.

Longer term, we need a better abstraction of board-specific setup in
this code so we're not hard-coding board specific GPIOs into the
driver, but for now this at least gets it back to working with
mainline davinci core code.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Finish merging updates for DM355 chips into musb/davinci.c now
that its support is in mainline:  kick in new DRVVBUS controls.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Support OID_802_3_MAC_OPTIONS in gen_ndis_query_resp() of rndis.c to
make RNDIS gadget pass 1c_SetMulticast subtest in Microsoft NDISTest6:

  http://www.microsoft.com/whdc/DevTools/tools/NDIStest.mspx

The other tests in NDISTest6 are passed.

[ dbrownell@users.sourceforge.net: remove OID_802_3_MAXIMUM_LIST_SIZE
setting ... it was bogus, this code only handles one entry, not 32.
And we don't know what would break if we lied about that... ]
Signed-off-by: Helen Chen <helen.chen@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

If an error is returned kfree must also be called.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

We could just make the USB_OHCI_HCD_PPC_OF option implicit
and selected only if at least one of USB_OHCI_HCD_PPC_OF_BE
and USB_OHCI_HCD_PPC_OF_LE are set.

[ dbrownell@users.sourceforge.net: fix patch manglation and dependencies ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

commit 1a1fab51 accidentally added the
device id to both tables in the driver, which causes problems as this is
only a single port device, not a multiple port device.

Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The audio gadget driver should use a "Linux" device id, instead
of relying on NetChip's vendor id.  So provide one out of our reserved
namespace.

Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This reverts commit 453f7755.

The driver should not have been accepted as the MSRT code is not
in the main kernel yet, which this depends on.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Hao Wu <hao.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch added Qisda(VID) & H21/H20(PID) into to supporting list.
Please help to check this patch,

From: Brad Lu <Brad.Lu@Qisda.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add modem portion of USB device labeled:
Model iCON 210, Qualcomm 3G HSDPA, designed in EU by Option

Device starts in usb-storage mode (1e0e:f000) and requires the use of a tool
like usb_modeswitch to switch it to modem mode (1e0e:9000).
Signed-off-by: Kai Engert <kaie@kuix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The isp1760_plat_remove function is declared with __devexit, so the
.remove assignment needs to be wrapped with __devexit_p().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This is an update to the "usb-ehci-update-toggle-state-for-linked-qhs"
patch.  Since an HCD's endpoint_reset method can be called in
interrupt context, it mustn't assume that interrupts are enabled or
that it can sleep.

So we revert to the original way of refreshing QHs' toggle bits.  Now
the endpoint_reset method merely clears the toggle flag in the device
structure (as was done before) and starts an async QH unlink.  When the
QH is linked again, after the unlink finishes and an URB is queued,
the qh_refresh() routine will update the QH's toggle bit.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: David <david@unsolicited.net>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

FHCI_PORT_DISABLED, -LOW and -FULL are mutually exclusive as status.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The product ID's for the following devices have been added:
- LOAD-n-GO
- ICD-U64
- PRIME-8
Signed-off-by: Jan Capek <jan@ccsinfo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Move USB_GADGET_IMX to the right section of Kconfig as this
controller is available only as integrated on i.MX CPU.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I recently bought a PC interface for the Cressi Edy dive computer
(www.cressi.it) and discovered that it uses the pl2303 chip, albeit
with ad-hoc vendor and product ids (04b8, 0521 respectively). Being in
the process of writing a linux software for such device (cressi only
provides a windows software), I patched the pl2303 linux driver to
have the interface recognized. I am submitting you the patch (very
basic) for inclusion in next kernel version.

From: Gianpaolo Cugola <gianpaoloc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This reverts commit 097041e5.

Trond had a better fix, which is the parent of this one ("Fix compile
error due to congestion_wait() changes")
Requested-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Move the definition of BLK_RW_ASYNC/BLK_RW_SYNC into linux/backing-dev.h
so that it is available to all callers of set/clear_bdi_congested().

This replaces commit 097041e5 ("fuse:
Fix build error"), which will be reverted.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - targa and targa-2ch fix
  ALSA: hda - fix beep tone calculation for IDT/STAC codecs
  ALSA: hda - Missing volume controls for Intel HDA (ALC269/EeePC)
  ALSA: hda - Disable AMD SB600 64bit address support only
  ALSA: hda - Check widget types while parsing capture source in patch_via.c
  ALSA: hda - Fix capture source selection in patch_via.c
  ALSA: hda - Add missing EAPD initialization for VIA codecs
  ALSA: hda - Clean up VT170x dig-in initialization code
  ALSA: hda - Fix error path in the sanity check in azx_pcm_open()
  ALSA: hda - move 8086:fb30 quirk (stac9205) to the proper section
  ASoC: Fix wm8753 register cache size and initialization
  ASoC: add locking to mpc5200-psc-ac97 driver
  ASoC: Fix mpc5200-psc-ac97 to ensure the data ready bit is cleared
  ASoC: Fix register cache initialisation for WM8753

commit 5404ac8e ("isofs: cleanup mount
option processing") missed conversion of joliet option flag resulting
in non-working Joliet support.

CC: walt <w41ter@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

PL2303 has private data shovelling methods that also have no fast path. Fix
them to work the same way as the default handler.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The sysrq code acquired a kref leak. Fix it by passing the tty separately
from the caller (thus effectively using the callers kref which all the
callers hold anyway)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We can't go around calling all sorts of magic per character functions at
full rate 3G data speed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>