When user-space has started a critical protocol session and a disconnect
event occurs, the rdev::crit_prot_nlportid remains set. This caused a
subsequent NL80211_CMD_CRIT_PROTO_START to fail (-EBUSY). Fix this by
clearing the rdev attribute and call .crit_proto_stop() callback upon
disconnect event.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The connection keys are zeroed out in all other cases except this
one. Let's fix the last one as well.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The value 5000 was put here with the addition of the timeout field to
ieee80211_start_tx_ba_session. It was originally added in mac80211 to
save resources for drivers like iwlwifi, which only supports a limited
number of concurrent aggregation sessions.

Since iwlwifi does not use minstrel_ht and other drivers don't need
this, 0 is a better default - especially since there have been
recent reports of aggregation setup related issues reproduced with
ath9k. This should improve stability without causing any adverse
effects.

Cc: stable@vger.kernel.org
Acked-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The change from cur_tp to the function
minstrel_get_tp_avg/minstrel_ht_get_tp_avg changed the unit used for the
current throughput. For example in minstrel_ht the correct
conversion between them would be:

    mrs->cur_tp / 10 == minstrel_ht_get_tp_avg(..).

This factor 10 must also be included in the calculation of
minstrel_get_expected_throughput and minstrel_ht_get_expected_throughput to
return values with the unit [Kbps] instead of [10Kbps]. Otherwise routing
algorithms like B.A.T.M.A.N. V will make incorrect decision based on these
values. Its kernel based implementation expects expected_throughput always
to have the unit [Kbps] and not sometimes [10Kbps] and sometimes [Kbps].

The same requirement has iw or olsrdv2's nl80211 based statistics module
which retrieve the same data via NL80211_STA_INFO_TX_BITRATE.

Cc: stable@vger.kernel.org
Fixes: 6a27b2c4 ("mac80211: restructure per-rate throughput calculation into function")
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Patch fixes this splat

BUG: KASAN: slab-out-of-bounds in minstrel_ht_update_stats.isra.7+0x6e1/0x9e0
[mac80211] at addr ffff8800cee640f4 Read of size 4 by task swapper/3/0
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Link: http://lkml.kernel.org/r/CALYGNiNyJhSaVnE35qS6UCGaSb2Dx1_i5HcRavuOX14oTz2P+w@mail.gmail.comAcked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Use kzalloc instead of kmalloc for struct tid_ampdu_rx to
initialize the "removed" field (all others are initialized
manually). That fixes:

UBSAN: Undefined behaviour in net/mac80211/rx.c:932:29
load of value 2 is not a valid value for type '_Bool'
CPU: 3 PID: 1134 Comm: kworker/u16:7 Not tainted 4.5.0-rc1+ #265
Workqueue: phy0 rt2x00usb_work_rxdone
 0000000000000004 ffff880254a7ba50 ffffffff8181d866 0000000000000007
 ffff880254a7ba78 ffff880254a7ba68 ffffffff8188422d ffffffff8379b500
 ffff880254a7bab8 ffffffff81884747 0000000000000202 0000000348620032
Call Trace:
 [<ffffffff8181d866>] dump_stack+0x45/0x5f
 [<ffffffff8188422d>] ubsan_epilogue+0xd/0x40
 [<ffffffff81884747>] __ubsan_handle_load_invalid_value+0x67/0x70
 [<ffffffff82227b4d>] ieee80211_sta_reorder_release.isra.16+0x5ed/0x730
 [<ffffffff8222ca14>] ieee80211_prepare_and_rx_handle+0xd04/0x1c00
 [<ffffffff8222db03>] __ieee80211_rx_handle_packet+0x1f3/0x750
 [<ffffffff8222e4a7>] ieee80211_rx_napi+0x447/0x990

While at it, convert to use sizeof(*tid_agg_rx) instead.

Fixes: 788211d8 ("mac80211: fix RX A-MPDU session reorder timer deletion")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
[reword commit message, use sizeof(*tid_agg_rx)]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since cfg80211 frequently takes actions from its netdev notifier
call, wireless extensions messages could still be ordered badly
since the wext netdev notifier, since wext is built into the
kernel, runs before the cfg80211 netdev notifier. For example,
the following can happen:

5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default
    link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST,UP>
    link/ether

when setting the interface down causes the wext message.

To also fix this, export the wireless_nlevent_flush() function
and also call it from the cfg80211 notifier.

Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Beniamino reported that he was getting an RTM_NEWLINK message for a
given interface, after the RTM_DELLINK for it. It turns out that the
message is a wireless extensions message, which was sent because the
interface had been connected and disconnection while it was deleted
caused a wext message.

For its netlink messages, wext uses RTM_NEWLINK, but the message is
without all the regular rtnetlink attributes, so "ip monitor link"
prints just rudimentary information:

5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default
    link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
Deleted 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default
    link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST,UP>
    link/ether
(from my hwsim reproduction)

This can cause userspace to get confused since it doesn't expect an
RTM_NEWLINK message after RTM_DELLINK.

The reason for this is that wext schedules a worker to send out the
messages, and the scheduling delay can cause the messages to get out
to userspace in different order.

To fix this, have wext register a netdevice notifier and flush out
any pending messages when netdevice state changes. This fixes any
ordering whenever the original message wasn't sent by a notifier
itself.

Cc: stable@vger.kernel.org
Reported-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The code within wait_event_interruptible() is called with
!TASK_RUNNING, so mustn't call any functions that can sleep,
like mutex_lock().

Since we re-check the list_empty() in a loop after the wait,
it's safe to simply use list_empty() without locking.

This bug has existed forever, but was only discovered now
because all userspace implementations, including the default
'rfkill' tool, use poll() or select() to get a readable fd
before attempting to read.

Cc: stable@vger.kernel.org
Fixes: c64fb016 ("rfkill: create useful userspace interface")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

During a sw scan ieee80211_iface_work ignores work items for all vifs.
However after the scan complete work is requeued only for STA, ADHOC
and MESH iftypes.

This occasionally results in event processing getting delayed/not
processed for iftype AP when it coexists with a STA. This can result
in data halt and eventually disconnection on the AP interface.

Cc: stable@vger.kernel.org
Signed-off-by: Sachin Kulkarni <Sachin.Kulkarni@imgtec.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Non-bufferable MMPDUs are sent out to STAs even while in PS mode
(for example probe responses). Applying filtered frame handling for
these doesn't seem to make much sense and will only create more
air utilization when the STA wakes up. Hence, apply filtered frame
handling only for bufferable MMPDUs.

Discovered while testing an old VOIP phone that started probing
for APs while in PS mode. The mac80211/ath9k AP where the STA is
associated would reply with a probe response but the phone sometimes
moved to a new channel already and couldn't ack the probe response
anymore. In that case mac80211 applied filtered frame handling
for the un-acked probe response.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

On hw restart, mac80211 might try to reconfigure already
stopped sched scan, if ieee80211_sched_scan_stopped_work()
wasn't scheduled yet.

This in turn will keep the device driver with scheduled scan
configured, while both mac80211 and cfg80211 will clear
their sched scan state once the work is scheduled.

Fix it by ignoring ieee80211_sched_scan_stopped() calls
while in hw restart, and flush the work before starting
the reconfiguration.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

My commit below broken PS-Poll handling. In case the driver
has no frames buffered, driver_release_tids will be 0, but
calling find_highest_prio_tid() with 0 as a parameter is
not a good idea:
fls(0) - 1 = -1.
This bug caused mac80211 to think that frames were buffered
in the driver which in turn was confused because mac80211
was asking to release frames that were not reported to
exist.
On iwlwifi, this led to the WARNING below:

WARNING: CPU: 0 PID: 11230 at drivers/net/wireless/intel/iwlwifi/mvm/sta.c:1733 iwl_mvm_sta_modify_sleep_tx_count+0x2af/0x320 [iwlmvm]()
ffffffffc0627c60 ffff8800069b7648 ffffffff81888913 0000000000000000
0000000000000000 ffff8800069b7688 ffffffff81089d6a ffff8800069b7678
0000000000000001 ffff88003b35abf0 ffff88000698b128 ffff8800069b76d4
Call Trace:
[<ffffffff81888913>] dump_stack+0x4c/0x65
[<ffffffff81089d6a>] warn_slowpath_common+0x8a/0xc0
[<ffffffff81089e5a>] warn_slowpath_null+0x1a/0x20
[<ffffffffc05f36bf>] iwl_mvm_sta_modify_sleep_tx_count+0x2af/0x320 [iwlmvm]
[<ffffffffc05dae41>] iwl_mvm_mac_release_buffered_frames+0x31/0x40 [iwlmvm]
[<ffffffffc045d8b6>] ieee80211_sta_ps_deliver_response+0x6e6/0xd80 [mac80211]
[<ffffffffc0461296>] ieee80211_sta_ps_deliver_poll_response+0x26/0x30 [mac80211]
[<ffffffffc048f743>] ieee80211_rx_handlers+0xa83/0x2900 [mac80211]
[<ffffffffc04917ad>] ieee80211_prepare_and_rx_handle+0x1ed/0xa70 [mac80211]
[<ffffffffc045e3d5>] ? sta_info_get_bss+0x5/0x4a0 [mac80211]
[<ffffffffc04925b6>] ieee80211_rx_napi+0x586/0xcd0 [mac80211]
[<ffffffffc05eaa3e>] iwl_mvm_rx_rx_mpdu+0x59e/0xc60 [iwlmvm]

Fixes: 0ead2510 ("mac80211: allow the driver to send EOSP when needed")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This reverts commit cd37a90b.

Different userspace programs interpreted HWSIM_ATTR_ADDR_TRANSMITTER
and HWSIM_ATTR_ADDR_RECEIVER differently: some expected it to
be an unchanging hardware address that is tied to the radio despite
which address is configured on the interface, while others expected
to be a copy of the address in the frame (the configured address).
The intent of the original authors is unclear.

The latter interpretation doesn't really work properly with multiple
vifs and broadcast frames.  Also, as the TA is already in the
frame, userspace programs can actually support configured addresses
in the former interpretation by mapping between them and the supplied
HWSIM_ATTR_ADDR_TRANSMITTER.

So, in the interest of API stability, revert to the previous mode
of operation and going forward use the former interpretation.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

On reconfig, in case of sched_scan_req->n_scan_plans > 1,
local->sched_scan_req was never cleared, although
cfg80211_sched_scan_stopped_rtnl() was called, resulting
in local->sched_scan_req holding a stale and preventing
further scheduled scan requests.

Clear it explicitly in this case.

Fixes: 42a7e82c6792 ("mac80211: Do not restart scheduled scan if multiple scan plans are set")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Defer ROC requests during hw restart, as the driver
might not be fully configured in this stage (e.g.
channel contexts were not added yet)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The rule definitions here aren't really valid, they would
be rejected if it came from userspace due to the bandwidth
specified being bigger than the rule's width.

This is fairly much inconsequential since the other rules
around them do enable the bandwidth, but express that better
using the NL80211_RRF_AUTO_BW flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211 module prints a lot of messages like below. Actually printing
once is acceptable but sometimes it will print again and again, it looks
very annoying. It is better to change these detail messages to debugging
only.

cfg80211: World regulatory domain updated:
cfg80211:  DFS Master region: unset
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)

The changes in this patch is to replace pr_info with pr_debug in function
print_rd_rules and print_regdomain_info
Signed-off-by: Dave Young <dyoung@redhat.com>
[change some pr_err() statements to at least keep the alpha2]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Ilan's previous commit 1b894521 ("mac80211: handle HW
ROC expired properly") neglected to take into account that
hw_begun was now always set in the software implementation
as well as the offloaded case.

Fix hw_begun to only apply to the offloaded case to make
the check in Ilan's commit safe and correct.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The current (new) code recalculates the new work timeout
for software remain-on-channel whenever any item started.
In two of the callers of ieee80211_handle_roc_started(),
this is completely pointless since they're for hardware
and will skip the recalculation entirely; it's necessary
only in the case of having just added a new item to the
list, as in the last remaining case the recalculation had
just been done.

This last case, however, is also problematic - if one of
the items on the list actually expires during the recalc
the list iteration outside becomes corrupted and crashes.

Fix this by moving the recalculation to the only place
where it's required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

when build_skb failed, we should goto refill the buffer.
Signed-off-by: Weidong Wang <wangweidong1@huawei.com>
Acked-by: Ding Tainhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antonio Quartulli says:

====================
net: batman-adv 20160114

Included bugfixes:
- avoid freeing batadv_hardif_neigh_node when still in use in other contexts
- prevent lockdep splat in mcast_free during shutdown
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Neil Horman says:

====================
3c59x: Fix dma map/unmap imbalances

	recent enhancements to libdma revealed a few minor bugs in 3c59x, in
which dma ranges were mapped as singles and unmaped as pages, or vice versa.
These patches fix those up.  Tested by myself with success
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

libdma debug found another page map/unmap imbalance in 3c59x.  Multi fragment
frames are mapped such that the lead fragment was mapped as a single entry,
while all other fragments were mapped as pages.  However, on unmapping they were
all unmapped as pages.  Fix is pretty easy, just unmap the lead frag as a single
entry, and bump the for loop initalization up by one so that all subsequent
frags get unmapped as pages
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

debug kernel noticed a screw up in 3c59x.  skbs being mapped as page were being
unmapped as singles.  Easy fix.  Tested by myself

Signed-off-by: Neil Horman <nhorman@tuxdriver.com
CC: "David S. Miller" <davem@davemloft.net>
CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based upon a report by Dmitry Vyukov.
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a missing break statement so we always return -EOPNOTSUPP.

Fixes: 3a49b4fd ('mlxsw: Adding layer 2 multicast support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bug fix for adding n_groups to the computation forgot
to adjust ">=" to ">" to keep the condition correct.
Signed-off-by: David S. Miller <davem@davemloft.net>

The neigh_list with batadv_hardif_neigh_node objects is accessed with only
rcu_read_lock in batadv_hardif_neigh_get and batadv_iv_neigh_print. Thus it
is not allowed to kfree the object before the rcu grace period ends (which
may still protects context accessing this object). Therefore the object has
first to be removed from the neigh_list and then it has either wait with
synchronize_rcu or call_rcu till the grace period ends before it can be
freed.

Fixes: cef63419 ("batman-adv: add list of unique single hop neighbors per hard-interface")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>

While testing, we got something like this:

WARNING: CPU: 0 PID: 238 at net/batman-adv/multicast.c:142 batadv_mcast_mla_tt_retract+0x94/0x205 [batman_adv]()
[...]
Call Trace:
[<ffffffff815fc597>] dump_stack+0x4b/0x64
[<ffffffff810b34dc>] warn_slowpath_common+0xbc/0x120
[<ffffffffa0024ec5>] ? batadv_mcast_mla_tt_retract+0x94/0x205 [batman_adv]
[<ffffffff810b3705>] warn_slowpath_null+0x15/0x20
[<ffffffffa0024ec5>] batadv_mcast_mla_tt_retract+0x94/0x205 [batman_adv]
[<ffffffffa00273fe>] batadv_mcast_free+0x36/0x39 [batman_adv]
[<ffffffffa0020c77>] batadv_mesh_free+0x7d/0x13f [batman_adv]
[<ffffffffa0036a6b>] batadv_softif_free+0x15/0x25 [batman_adv]
[...]
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>

when build_skb failed, it may occure a NULL pointer.
So add a 'NULL check' for it.
Signed-off-by: Weidong Wang <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull oower management and ACPI updates from Rafael Wysocki:
 "As far as the number of commits goes, ACPICA takes the lead this time,
  followed by cpufreq and the device properties framework changes.

  The most significant new feature is the debugfs-based interface to the
  ACPICA's AML debugger added in the previous cycle and a new user space
  tool for accessing it.

  On the cpufreq front, the core is updated to handle governors more
  efficiently, particularly on systems where a single cpufreq policy
  object is shared between multiple CPUs, and there are quite a few
  changes in drivers (intel_pstate, cpufreq-dt etc).

  The device properties framework is updated to handle built-in (ie
  included in the kernel itself) device properties better, among other
  things by adding a fallback mechanism that will allow drivers to
  provide default properties to be used in case the plaform firmware
  doesn't provide the properties expected by them.

  The Operating Performance Points (OPP) framework gets new DT bindings
  and debugfs support.

  A new cpufreq driver for ST platforms is added and the ACPI driver for
  AMD SoCs will now support the APM X-Gene ACPI I2C device.

  The rest is mostly fixes and cleanups all over.

  Specifics:

   - Add a debugfs-based interface for interacting with the ACPICA's AML
     debugger introduced in the previous cycle and a new user space tool
     for that, fix some bugs related to the AML debugger and clean up
     the code in question (Lv Zheng, Dan Carpenter, Colin Ian King,
     Markus Elfring).

   - Update ACPICA to upstream revision 20151218 including a number of
     fixes and cleanups in the ACPICA core (Bob Moore, Lv Zheng, Labbe
     Corentin, Prarit Bhargava, Colin Ian King, David E Box, Rafael
     Wysocki).

     In particular, the previously added erroneous support for the _SUB
     object is dropped, the concatenate operator will support all ACPI
     objects now, the Debug Object handling is improved, the SuperName
     handling of parameters being control methods is fixed, the
     ObjectType operator handling is updated to follow ACPI 5.0A and the
     handling of CondRefOf and RefOf is updated accordingly, module-
     level code will be executed after loading each ACPI table now
     (instead of being run once after all tables containing AML have
     been loaded), the Operation Region handlers management is updated
     to fix some reported problems and a the ACPICA code in the kernel
     is more in line with the upstream now.

   - Update the ACPI backlight driver to provide information on whether
     or not it will generate key-presses for brightness change hotkeys
     and update some platform drivers (dell-wmi, thinkpad_acpi) to use
     that information to avoid sending double key-events to users pace
     for these, add new ACPI backlight quirks (Hans de Goede, Aaron Lu,
     Adrien Schildknecht).

   - Improve the ACPI handling of interrupt GPIOs (Christophe Ricard).

   - Fix the handling of the list of device IDs of device objects found
     in the ACPI namespace and add a helper for checking if there is a
     device object for a given device ID (Lukas Wunner).

   - Change the logic in the ACPI namespace scanning code to create
     struct acpi_device objects for all ACPI device objects found in the
     namespace even if _STA fails for them which helps to avoid device
     enumeration problems on Microsoft Surface 3 (Aaron Lu).

   - Add support for the APM X-Gene ACPI I2C device to the ACPI driver
     for AMD SoCs (Loc Ho).

   - Fix the long-standing issue with the DMA controller on Intel SoCs
     where ACPI tables have no power management support for the DMA
     controller itself, but it can be powered off automatically when the
     last (other) device on the SoC is powered off via ACPI and clean up
     the ACPI driver for Intel SoCs (acpi-lpss) after previous attempts
     to fix that problem (Andy Shevchenko).

   - Assorted ACPI fixes and cleanups (Andy Lutomirski, Colin Ian King,
     Javier Martinez Canillas, Ken Xue, Mathias Krause, Rafael Wysocki,
     Sinan Kaya).

   - Update the device properties framework for better handling of
     built-in properties, add support for built-in properties to the
     platform bus type, update the MFD subsystem's handling of device
     properties and add support for passing default configuration data
     as device properties to the intel-lpss MFD drivers, convert the
     designware I2C driver to use the unified device properties API and
     add a fallback mechanism for using default built-in properties if
     the platform firmware fails to provide the properties as expected
     by drivers (Andy Shevchenko, Mika Westerberg, Heikki Krogerus,
     Andrew Morton).

   - Add new Device Tree bindings to the Operating Performance Points
     (OPP) framework and update the exynos4412 DT binding accordingly,
     introduce debugfs support for the OPP framework (Viresh Kumar,
     Bartlomiej Zolnierkiewicz).

   - Migrate the mt8173 cpufreq driver to the new OPP bindings (Pi-Cheng
     Chen).

   - Update the cpufreq core to make the handling of governors more
     efficient, especially on systems where policy objects are shared
     between multiple CPUs (Viresh Kumar, Rafael Wysocki).

   - Fix cpufreq governor handling on configurations with
     CONFIG_HZ_PERIODIC set (Chen Yu).

   - Clean up the cpufreq core code related to the boost sysfs knob
     support and update the ACPI cpufreq driver accordingly (Rafael
     Wysocki).

   - Add a new cpufreq driver for ST platforms and corresponding Device
     Tree bindings (Lee Jones).

   - Update the intel_pstate driver to allow the P-state selection
     algorithm used by it to depend on the CPU ID of the processor it is
     running on, make it use a special P-state selection algorithm (with
     an IO wait time compensation tweak) on Atom CPUs based on the
     Airmont and Silvermont cores so as to reduce their energy
     consumption and improve intel_pstate documentation (Philippe
     Longepe, Srinivas Pandruvada).

   - Update the cpufreq-dt driver to support registering cooling devices
     that use the (P * V^2 * f) dynamic power draw formula where V is
     the voltage, f is the frequency and P is a constant coefficient
     provided by Device Tree and update the arm_big_little cpufreq
     driver to use that support (Punit Agrawal).

   - Assorted cpufreq driver (cpufreq-dt, qoriq, pcc-cpufreq,
     blackfin-cpufreq) updates (Andrzej Hajda, Hongtao Jia, Jacob
     Tanenbaum, Markus Elfring).

   - cpuidle core tweaks related to polling and measured_us calculation
     (Rik van Riel).

   - Removal of modularity from a few cpuidle drivers (clps711x, ux500,
     exynos) that cannot be built as modules in practice (Paul
     Gortmaker).

   - PM core update to prevent devices from being probed during system
     suspend/resume which is generally problematic and may lead to
     inconsistent behavior (Grygorii Strashko).

   - Assorted updates of the PM core and related code (Julia Lawall,
     Manuel Pégourié-Gonnard, Maruthi Bayyavarapu, Rafael Wysocki, Ulf
     Hansson).

   - PNP bus type updates (Christophe Le Roy, Heiner Kallweit).

   - PCI PM code cleanups (Jarkko Nikula, Julia Lawall).

   - cpupower tool updates (Jacob Tanenbaum, Thomas Renninger)"

* tag 'pm+acpi-4.5-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (177 commits)
  PM / clk: don't leave clocks enabled when driver not bound
  i2c: dw: Add APM X-Gene ACPI I2C device support
  ACPI / APD: Add APM X-Gene ACPI I2C device support
  ACPI / LPSS: change 'does not have' to 'has' in comment
  Revert "dmaengine: dw: platform: provide platform data for Intel"
  dmaengine: dw: return immediately from IRQ when DMA isn't in use
  dmaengine: dw: platform: power on device on shutdown
  ACPI / LPSS: override power state for LPSS DMA device
  PM / OPP: Use snprintf() instead of sprintf()
  Documentation: cpufreq: intel_pstate: enhance documentation
  ACPI, PCI, irq: remove redundant check for null string pointer
  ACPI / video: driver must be registered before checking for keypresses
  cpufreq-dt: fix handling regulator_get_voltage() result
  cpufreq: governor: Fix negative idle_time when configured with CONFIG_HZ_PERIODIC
  PM / sleep: Add support for read-only sysfs attributes
  ACPI: Fix white space in a structure definition
  ACPI / SBS: fix inconsistent indenting inside if statement
  PNP: respect PNP_DRIVER_RES_DO_NOT_CHANGE when detaching
  ACPI / PNP: constify device IDs
  ACPI / PCI: Simplify acpi_penalize_isa_irq()
  ...

Pull tracing updates from Steven Rostedt:
 "Not much new with tracing for this release.  Mostly just clean ups and
  minor fixes.

  Here's what else is new:

   - A new TRACE_EVENT_FN_COND macro, combining both _FN and _COND for
     those that want both.

   - New selftest to test the instance create and delete

   - Better debug output when ftrace fails"

* tag 'trace-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (24 commits)
  ftrace: Fix the race between ftrace and insmod
  ftrace: Add infrastructure for delayed enabling of module functions
  x86: ftrace: Fix the comments for ftrace_modify_code_direct()
  tracing: Fix comment to use tracing_on over tracing_enable
  metag: ftrace: Fix the comments for ftrace_modify_code
  sh: ftrace: Fix the comments for ftrace_modify_code()
  ia64: ftrace: Fix the comments for ftrace_modify_code()
  ftrace: Clean up ftrace_module_init() code
  ftrace: Join functions ftrace_module_init() and ftrace_init_module()
  tracing: Introduce TRACE_EVENT_FN_COND macro
  tracing: Use seq_buf_used() in seq_buf_to_user() instead of len
  bpf: Constify bpf_verifier_ops structure
  ftrace: Have ftrace_ops_get_func() handle RCU and PER_CPU flags too
  ftrace: Remove use of control list and ops
  ftrace: Fix output of enabled_functions for showing tramp
  ftrace: Fix a typo in comment
  ftrace: Show all tramps registered to a record on ftrace_bug()
  ftrace: Add variable ftrace_expected for archs to show expected code
  ftrace: Add new type to distinguish what kind of ftrace_bug()
  tracing: Update cond flag when enabling or disabling a trigger
  ...

Pull cgroup updates from Tejun Heo:

 - cgroup v2 interface is now official.  It's no longer hidden behind a
   devel flag and can be mounted using the new cgroup2 fs type.

   Unfortunately, cpu v2 interface hasn't made it yet due to the
   discussion around in-process hierarchical resource distribution and
   only memory and io controllers can be used on the v2 interface at the
   moment.

 - The existing documentation which has always been a bit of mess is
   relocated under Documentation/cgroup-v1/. Documentation/cgroup-v2.txt
   is added as the authoritative documentation for the v2 interface.

 - Some features are added through for-4.5-ancestor-test branch to
   enable netfilter xt_cgroup match to use cgroup v2 paths.  The actual
   netfilter changes will be merged through the net tree which pulled in
   the said branch.

 - Various cleanups

* 'for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: rename cgroup documentations
  cgroup: fix a typo.
  cgroup: Remove resource_counter.txt in Documentation/cgroup-legacy/00-INDEX.
  cgroup: demote subsystem init messages to KERN_DEBUG
  cgroup: Fix uninitialized variable warning
  cgroup: put controller Kconfig options in meaningful order
  cgroup: clean up the kernel configuration menu nomenclature
  cgroup_pids: fix a typo.
  Subject: cgroup: Fix incomplete dd command in blkio documentation
  cgroup: kill cgrp_ss_priv[CGROUP_CANFORK_COUNT] and friends
  cpuset: Replace all instances of time_t with time64_t
  cgroup: replace unified-hierarchy.txt with a proper cgroup v2 documentation
  cgroup: rename Documentation/cgroups/ to Documentation/cgroup-legacy/
  cgroup: replace __DEVEL__sane_behavior with cgroup2 fs type

Pull networking updates from Davic Miller:

 1) Support busy polling generically, for all NAPI drivers.  From Eric
    Dumazet.

 2) Add byte/packet counter support to nft_ct, from Floriani Westphal.

 3) Add RSS/XPS support to mvneta driver, from Gregory Clement.

 4) Implement IPV6_HDRINCL socket option for raw sockets, from Hannes
    Frederic Sowa.

 5) Add support for T6 adapter to cxgb4 driver, from Hariprasad Shenai.

 6) Add support for VLAN device bridging to mlxsw switch driver, from
    Ido Schimmel.

 7) Add driver for Netronome NFP4000/NFP6000, from Jakub Kicinski.

 8) Provide hwmon interface to mlxsw switch driver, from Jiri Pirko.

 9) Reorganize wireless drivers into per-vendor directories just like we
    do for ethernet drivers.  From Kalle Valo.

10) Provide a way for administrators "destroy" connected sockets via the
    SOCK_DESTROY socket netlink diag operation.  From Lorenzo Colitti.

11) Add support to add/remove multicast routes via netlink, from Nikolay
    Aleksandrov.

12) Make TCP keepalive settings per-namespace, from Nikolay Borisov.

13) Add forwarding and packet duplication facilities to nf_tables, from
    Pablo Neira Ayuso.

14) Dead route support in MPLS, from Roopa Prabhu.

15) TSO support for thunderx chips, from Sunil Goutham.

16) Add driver for IBM's System i/p VNIC protocol, from Thomas Falcon.

17) Rationalize, consolidate, and more completely document the checksum
    offloading facilities in the networking stack.  From Tom Herbert.

18) Support aborting an ongoing scan in mac80211/cfg80211, from
    Vidyullatha Kanchanapally.

19) Use per-bucket spinlock for bpf hash facility, from Tom Leiming.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1375 commits)
  net: bnxt: always return values from _bnxt_get_max_rings
  net: bpf: reject invalid shifts
  phonet: properly unshare skbs in phonet_rcv()
  dwc_eth_qos: Fix dma address for multi-fragment skbs
  phy: remove an unneeded condition
  mdio: remove an unneed condition
  mdio_bus: NULL dereference on allocation error
  net: Fix typo in netdev_intersect_features
  net: freescale: mac-fec: Fix build error from phy_device API change
  net: freescale: ucc_geth: Fix build error from phy_device API change
  bonding: Prevent IPv6 link local address on enslaved devices
  IB/mlx5: Add flow steering support
  net/mlx5_core: Export flow steering API
  net/mlx5_core: Make ipv4/ipv6 location more clear
  net/mlx5_core: Enable flow steering support for the IB driver
  net/mlx5_core: Initialize namespaces only when supported by device
  net/mlx5_core: Set priority attributes
  net/mlx5_core: Connect flow tables
  net/mlx5_core: Introduce modify flow table command
  net/mlx5_core: Managing root flow table
  ...

Pull crypto update from Herbert Xu:
 "Algorithms:
   - Add RSA padding algorithm

  Drivers:
   - Add GCM mode support to atmel
   - Add atmel support for SAMA5D2 devices
   - Add cipher modes to talitos
   - Add rockchip driver for rk3288
   - Add qat support for C3XXX and C62X"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (103 commits)
  crypto: hifn_795x, picoxcell - use ablkcipher_request_cast
  crypto: qat - fix SKU definiftion for c3xxx dev
  crypto: qat - Fix random config build issue
  crypto: ccp - use to_pci_dev and to_platform_device
  crypto: qat - Rename dh895xcc mmp firmware
  crypto: 842 - remove WARN inside printk
  crypto: atmel-aes - add debug facilities to monitor register accesses.
  crypto: atmel-aes - add support to GCM mode
  crypto: atmel-aes - change the DMA threshold
  crypto: atmel-aes - fix the counter overflow in CTR mode
  crypto: atmel-aes - fix atmel-ctr-aes driver for RFC 3686
  crypto: atmel-aes - create sections to regroup functions by usage
  crypto: atmel-aes - fix typo and indentation
  crypto: atmel-aes - use SIZE_IN_WORDS() helper macro
  crypto: atmel-aes - improve performances of data transfer
  crypto: atmel-aes - fix atmel_aes_remove()
  crypto: atmel-aes - remove useless AES_FLAGS_DMA flag
  crypto: atmel-aes - reduce latency of DMA completion
  crypto: atmel-aes - remove unused 'err' member of struct atmel_aes_dev
  crypto: atmel-aes - rework crypto request completion
  ...

Pull UBI/UBIFS updates from Richard Weinberger:
 "This contains three changes - two cleanups and one UBI wear leveling
  improvement by Sebastian Siewior"

* tag 'upstream-4.5-rc1' of git://git.infradead.org/linux-ubifs:
  ubifs: Use XATTR_*_PREFIX_LEN
  UBIFS: add a comment in key.h for unused parameter
  mtd: ubi: wl: avoid erasing a PEB which is empty

Pull configfs updates from Christoph Hellwig:
 "I'm assisting Joel as co-maintainer and patch monkey now, and you will
  see pull reuquests from me for a while.

  Besides the MAINTAINERS update there is just a single change, which
  adds support for binary attributes to configfs, which are very similar
  to the sysfs binary attributes.  Thanks to Pantelis Antoniou!

  You will see another actually bigger set of configfs changes in the
  SCSI target pull from Nic - those were merged before this new tree
  even existed"

* tag 'configfs-for-linus' of git://git.infradead.org/users/hch/configfs:
  configfs: add myself as co-maintainer, updated git tree
  configfs: implement binary attributes

Pull GFS2 updates from Bob Peterson:
 "Here is a list of patches we've accumulated for GFS2 for the current
  upstream merge window.  Last window's set was short, but I warned that
  this one would be bigger, and so it is.  We've got 19 patches:

   - A patch from Abhi Das to propagate the GFS2_DIF_SYSTEM bit so that
     newly added journals don't get flagged, deleted, and recreated by
     fsck.gfs2.

   - Two patches from Andreas Gruenbacher to improve GFS2 performance
     where extended attributes are involved.

   - A patch from Andy Price to fix a suspicious rcu dereference error.

   - Two patches from Ben Marzinski that rework how GFS2's NFS cookies
     are managed.  This fixes readdir problems with nfs-over-gfs2.

   - A patch from Ben Marzinski that fixes a race in unmounting GFS2.

   - A set of four patches from me to move the resource group
     reservations inside the gfs2 inode to improve performance and fix a
     bug whereby get_write_access improperly prevented some operations
     like chown.

   - A patch from me to spinlock-protect the setting of system statfs
     file data.  This was causing small discrepancies between df and du.

   - A patch from me to reintroduce a timeout while clearing glocks
     which was accidentally dropped some time ago.

   - A patch from me to wait for iopen glock dequeues in order to
     improve deleting of files that were unlinked from a different
     cluster node.

   - A patch from me to ensure metadata address spaces get truncated
     when an inode is evicted.

   - A patch from me to fix a bug in which a memory leak could occur in
     some error cases when inodes were trying to be created.

   - A patch to consistently use iopen glocks to transition from the
     unlinked state to the deleted state.

   - A patch to fix a glock reference count error when inode creation
     fails.

   - A patch from Junxiao Bi to fix an flock panic.

   - A patch from Markus Elfring that removes an unnecessary if"

* tag 'gfs2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  gfs2: fix flock panic issue
  GFS2: Don't do glock put on when inode creation fails
  GFS2: Always use iopen glock for gl_deletes
  GFS2: Release iopen glock in gfs2_create_inode error cases
  GFS2: Truncate address space mapping when deleting an inode
  GFS2: Wait for iopen glock dequeues
  gfs2: clear journal live bit in	gfs2_log_flush
  gfs2: change gfs2 readdir cookie
  gfs2: keep offset when splitting dir leaf blocks
  GFS2: Reintroduce a timeout in function gfs2_gl_hash_clear
  GFS2: Update master statfs buffer with sd_statfs_spin locked
  GFS2: Reduce size of incore inode
  GFS2: Make rgrp reservations part of the gfs2_inode structure
  GFS2: Extract quota data from reservations structure (revert 5407e242)
  gfs2: Extended attribute readahead optimization
  gfs2: Extended attribute readahead
  GFS2: Use rht_for_each_entry_rcu in glock_hash_walk
  GFS2: Delete an unnecessary check before the function call "iput"
  gfs2: Automatically set GFS2_DIF_SYSTEM flag on system files