This patch adds support for the GPIOs found on the ITE super-I/O chips
IT87xx.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The parameter offset is an unsigned, so it makes no sense to compare
it for >= 0. Fix the compiler warning regarding this by removing this
comparison.

As the macro GPIO_OFFSET_VALID is only used at this single place, simplify
the code by dropping the macro completely and dropping the invert, too.

No functional change.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This fixes error checking in the function device_pca957x_init
to properly check and return error code values from the calls
to the function pca953x_write_regs if they fail as to properly
signal callers when a error occurs due a failure when writing
registers for this gpio based device.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Turn the ath79 driver into a true driver supporting multiple
instances. While at it also removed unneed includes and make use of
the BIT() macro.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Remove this driver now that Bjorn has introduced a pinctrl driver
for msm8660 and the dts files have been updated with the pinctrl
compatibles.

Cc: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The state container of the Zynq GPIO driver is sometimes
extracted from the gpio_chip exploiting the fact that offsetof()
the struct gpio_chip inside the struct zynq_gpio is 0, so
the container_of() is in practice a noop. However if a member
is added to struct zynq_gpio in front of struct gpio_chip,
things will break. Using proper container_of() avoids this
problem.

Semantically this is a noop, the compiler will optimize it away,
but syntactically it makes me happier.

Also replace some explicit container_of() calls with the helper
function.

Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ezra Savard <ezra.savard@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The state container of the vf610 GPIO driver is sometimes
extracted from the gpio_chip exploiting the fact that offsetof()
the struct gpio_chip inside the struct vf610_gpio_port is 0, so
the container_of() is in practice a noop. However if a member
is added to struct vf610_gpio_port in front of struct gpio_chip,
things will break. Using proper container_of() avoids this
problem.

Semantically this is a noop, the compiler will optimize it away,
but syntactically it makes me happier.

Also replace some explicit container_of() calls with the helper
function.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The state container of the sx150x GPIO driver is sometimes
extracted from the gpio_chip exploiting the fact that offsetof()
the struct gpio_chip inside the struct sx150x_chip is 0, so
the container_of() is in practice a noop. However if a member
is added to struct sx150_chip in front of struct gpio_chip, things
will break. Using proper container_of() avoids this problem.

Semantically this is a noop, the compiler will optimize it away,
but syntactically it makes me happier.

Cc: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The state container of the Altera GPIO driver is extracted from
the gpio_chip exploiting the fact that offsetof() the
struct gpio_chip inside the struct of_mm_gpio_chip are both 0, so
the container_of() is in practice a noop. However if a member
is added to struct altera_gpio_chip in front of
struct of_mm_gpio_chip, things will break. Using proper
container_of() avoids this problem.

Semantically this is a noop, the compiler will optimize it away,
but syntactically it makes me happier.

Cc: Tien Hock Loh <thloh@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The state container of the etraxfs GPIO driver is extracted from
the gpio_chip exploiting the fact that offsetof() the
struct gpio_chip inside the struct bgpio_chip are both 0, so
the container_of() is in practice a noop. However if a member
is added to struct etraxfs_gpio_chip in front of
struct bgpio_chip, things will break. Using proper container_of()
avoids this problem.

Semantically this is a noop, the compiler will optimize it away,
but syntactically it makes me happier.
Acked-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

I couldn't follow this code flow. Make it dirt simple to figure
out what is going on and get proper debug prints. Warn if we
set up an IRQ without any trigger. Should make no semantic
difference.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This refactors the changes to the GPIO line naming mechanism to
not have so widespread effects, instead we conclude the patch series
by having created a name attribute in the GPIO descriptor, that need
not be globally unique, and it will be initialized from the old
.names array in struct gpio_chip if it exists, then used in the legacy
sysfs code like the array was used previously.

The associated changes to name lines from the device tree are
controversial and need to stand alone from this. Resulting changes:

1. Remove the export and the header for the gpio_name_to_desc() as so
far the only use is inside gpiolib.c. Staticize gpio_name_to_desc()
and move it above the only function using it.

2. Only print a warning if there are two GPIO lines with the same name.
The reason is to preserve current behaviour: before the previous
changes to the naming mechanism this would not reject probing the
driver, instead the error would occur when trying to export the line
in sysfs, so restore this behaviour, but print a friendly warning
if names collide.

Cc: Johan Hovold <johan@kernel.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add some information about gpio names to the debugfs gpio file. name and
label of a GPIO are then displayed next to each other. This way it is
easy to see what the real name of GPIO is and what the driver requested
it for.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[Dropped unsolicited sysfs ABI patch hunk]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The name is now stored in the gpio descriptor as well, for example to
allow to store names from DT. This patch changes the sysfs gpio files
to use the gpio descriptor name.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds GPIO names to the GPIO descriptors when initializing the
gpiochip. It also introduces a check whether any of the new names will
conflict with an existing GPIO name.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The latest gpio hogging mechanism assigns each gpio a 'line-name' in the
devicetree. The 'name' field is different from the 'label' field.
'label' is only used for requested GPIOs to describe its current use by
driver or userspace.

The 'name' field describes the GPIO itself, not the use. This is most
likely identical to the label in the schematic on the GPIO line and
should help to find this particular GPIO.

This is equivalent to the gpiochip->names array. However names should be
stored in the GPIO descriptor. We will use gpiochip->names in the future
only as initializer for the GPIO descriptors for drivers that assign
GPIO names hardcoded. All other GPIO names will be parsed from DT and
directly assigned to the GPIO descriptor.

This patch adds a helper function to find gpio descriptors by name
instead of gpio number.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The gpio hogging functions are currently only used for gpio-hogging. But
these functions are widely generic ones which parse gpio device nodes in
the DT.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull ARM fixes from Russell King:
 "Three fixes and a resulting cleanup for -rc2:

   - Andre Przywara reported that he was seeing a warning with the new
     cast inside DMA_ERROR_CODE's definition, and fixed the incorrect
     use.

   - Doug Anderson noticed that kgdb causes a "scheduling while atomic"
     bug.

   - OMAP5 folk noticed that their Thumb-2 compiled X servers crashed
     when enabling support to cover ARMv6 CPUs due to a kernel bug
     leaking some conditional context into the signal handler"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8425/1: kgdb: Don't try to stop the machine when setting breakpoints
  ARM: 8437/1: dma-mapping: fix build warning with new DMA_ERROR_CODE definition
  ARM: get rid of needless #if in signal handling code
  ARM: fix Thumb2 signal handling when ARMv6 is enabled

Merge tag 'linux-kselftest-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest fixes from Shuah Khan:
 "This update contains 7 fixes for problems ranging from build failurs
  to incorrect error reporting"

* tag 'linux-kselftest-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests: exec: revert to default emit rule
  selftests: change install command to rsync
  selftests: mqueue: simplify the Makefile
  selftests: mqueue: allow extra cflags
  selftests: rename jump label to static_keys
  selftests/seccomp: add support for s390
  seltests/zram: fix syntax error

Pull power management and ACPI updates from Rafael Wysocki:
 "Included are: a somewhat late devfreq update which however is mostly
  fixes and cleanups with one new thing only (the PPMUv2 support on
  Exynos5433), an ACPI cpufreq driver fixup and two ACPI core cleanups
  related to preprocessor directives.

  Specifics:

   - Fix a memory allocation size in the devfreq core (Xiaolong Ye).

   - Fix a mistake in the exynos-ppmu DT binding (Javier Martinez
     Canillas).

   - Add support for PPMUv2 ((Platform Performance Monitoring Unit
     version 2.0) on the Exynos5433 SoCs (Chanwoo Choi).

   - Fix a type casting bug in the Exynos PPMU code (MyungJoo Ham).

   - Assorted devfreq code cleanups and optimizations (Javi Merino,
     MyungJoo Ham, Viresh Kumar).

   - Fix up the ACPI cpufreq driver to use a more lightweight way to get
     to its private data in the ->get() callback (Rafael J Wysocki).

   - Fix a CONFIG_ prefix bug in one of the ACPI drivers and make the
     ACPI subsystem use IS_ENABLED() instead of #ifdefs in function
     bodies (Sudeep Holla)"

* tag 'pm+acpi-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: acpi-cpufreq: Use cpufreq_cpu_get_raw() in ->get()
  ACPI: Eliminate CONFIG_.*{, _MODULE} #ifdef in favor of IS_ENABLED()
  ACPI: int340x_thermal: add missing CONFIG_ prefix
  PM / devfreq: Fix incorrect type issue.
  PM / devfreq: tegra: Update governor to use devfreq_update_stats()
  PM / devfreq: comments for get_dev_status usage updated
  PM / devfreq: drop comment about thermal setting max_freq
  PM / devfreq: cache the last call to get_dev_status()
  PM / devfreq: Drop unlikely before IS_ERR(_OR_NULL)
  PM / devfreq: exynos-ppmu: bit-wise operation bugfix.
  PM / devfreq: exynos-ppmu: Update documentation to support PPMUv2
  PM / devfreq: exynos-ppmu: Add the support of PPMUv2 for Exynos5433
  PM / devfreq: event: Remove incorrect property in exynos-ppmu DT binding

Pull clk fixes from Stephen Boyd:
 "A few driver fixes for tegra, rockchip, and st SoCs and a two-liner in
  the framework to avoid oops when get_parent ops return out of range
  values on tegra platforms"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  drivers: clk: st: Rename st_pll3200c32_407_c0_x into st_pll3200c32_cx_x
  clk: check for invalid parent index of orphans in __clk_init()
  clk: tegra: dfll: Properly protect OPP list
  clk: rockchip: add critical clock for rk3368

Merge tag 'led-fixes-for-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED fixes from Jacek Anaszewski:
 - fix module autoload for six OF platform drivers (aat1290, bcm6328,
   bcm6358, ktd2692, max77693, ns2)
 - aat1290: add missing static modifier
 - ipaq-micro: add missing LEDS_CLASS dependency
 - lp55xx: correct Kconfig dependecy for f/w user helper

* tag 'led-fixes-for-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  leds:lp55xx: Correct Kconfig dependency for f/w user helper
  leds: leds-ipaq-micro: Add LEDS_CLASS dependency
  leds: aat1290: add 'static' modifier to init_mm_current_scale
  leds: leds-ns2: Fix module autoload for OF platform driver
  leds: max77693: Fix module autoload for OF platform driver
  leds: ktd2692: Fix module autoload for OF platform driver
  leds: bcm6358: Fix module autoload for OF platform driver
  leds: bcm6328: Fix module autoload for OF platform driver
  leds: aat1290: Fix module autoload for OF platform driver

Pull rdma fixes from Doug Ledford:
 "The new hfi1 driver in staging/rdma has had a number of fixup patches
  since being added to the tree.  This is the first batch of those fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  IB/hfi: Properly set permissions for user device files
  IB/hfi1: mask vs shift confusion
  IB/hfi1: clean up some defines
  IB/hfi1: info leak in get_ctxt_info()
  IB/hfi1: fix a locking bug
  IB/hfi1: checking for NULL instead of IS_ERR
  IB/hfi1: fix sdma_descq_cnt parameter parsing
  IB/hfi1: fix copy_to/from_user() error handling
  IB/hfi1: fix pstateinfo from returning improperly byteswapped value

Pull libnvdimm fixes from Dan Williams:

 - a boot regression (since v4.2) fix for some ARM configurations from
   Tyler

 - regression (since v4.1) fixes for mkfs.xfs on a DAX enabled device
   from Jeff.  These are tagged for -stable.

 - a pair of locking fixes from Axel that are hidden from lockdep since
   they involve device_lock().  The "btt" one is tagged for -stable, the
   other only applies to the new "pfn" mechanism in v4.3.

 - a fix for the pmem ->rw_page() path to use wmb_pmem() from Ross.

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  mm: fix type cast in __pfn_to_phys()
  pmem: add proper fencing to pmem_rw_page()
  libnvdimm: pfn_devs: Fix locking in namespace_store
  libnvdimm: btt_devs: Fix locking in namespace_store
  blockdev: don't set S_DAX for misaligned partitions
  dax: fix O_DIRECT I/O to the last block of a blockdev

Pull block updates from Jens Axboe:
 "This is a bit bigger than it should be, but I could (did) not want to
  send it off last week due to both wanting extra testing, and expecting
  a fix for the bounce regression as well.  In any case, this contains:

   - Fix for the blk-merge.c compilation warning on gcc 5.x from me.

   - A set of back/front SG gap merge fixes, from me and from Sagi.
     This ensures that we honor SG gapping for integrity payloads as
     well.

   - Two small fixes for null_blk from Matias, fixing a leak and a
     capacity propagation issue.

   - A blkcg fix from Tejun, fixing a NULL dereference.

   - A fast clone optimization from Ming, fixing a performance
     regression since the arbitrarily sized bio's were introduced.

   - Also from Ming, a regression fix for bouncing IOs"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: fix bounce_end_io
  block: blk-merge: fast-clone bio when splitting rw bios
  block: blkg_destroy_all() should clear q->root_blkg and ->root_rl.blkg
  block: Copy a user iovec if it includes gaps
  block: Refuse adding appending a gapped integrity page to a bio
  block: Refuse request/bio merges with gaps in the integrity payload
  block: Check for gaps on front and back merges
  null_blk: fix wrong capacity when bs is not 512 bytes
  null_blk: fix memory leak on cleanup
  block: fix bogus compiler warnings in blk-merge.c

Commit 505a666e ("writeback: plug writeback in wb_writeback() and
writeback_inodes_wb()") has us holding a plug during writeback_sb_inodes,
which increases the merge rate when relatively contiguous small files
are written by the filesystem.  It helps both on flash and spindles.

For an fs_mark workload creating 4K files in parallel across 8 drives,
this commit improves performance ~9% more by unplugging before calling
cond_resched().  cond_resched() doesn't trigger an implicit unplug, so
explicitly getting the IO down to the device before scheduling reduces
latencies for anyone waiting on clean pages.

It also cuts down on how often we use kblockd to unplug, which means
less work bouncing from one workqueue to another.

Many more details about how we got here:

  https://lkml.org/lkml/2015/9/11/570Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The various definitions of __pfn_to_phys() have been consolidated to
use a generic macro in include/asm-generic/memory_model.h. This hit
mainline in the form of 012dcef3 "mm: move __phys_to_pfn and
__pfn_to_phys to asm/generic/memory_model.h". When the generic macro
was implemented the type cast to phys_addr_t was dropped which caused
boot regressions on ARM platforms with more than 4GB of memory and
LPAE enabled.

It was suggested to use PFN_PHYS() defined in include/linux/pfn.h
as provides the correct logic and avoids further duplication.
Reported-by: kernelci.org bot <bot@kernelci.org>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

* acpi-bus:
  ACPI: Eliminate CONFIG_.*{, _MODULE} #ifdef in favor of IS_ENABLED()
  ACPI: int340x_thermal: add missing CONFIG_ prefix

* pm-cpufreq:
  cpufreq: acpi-cpufreq: Use cpufreq_cpu_get_raw() in ->get()

* pm-devfreq:
  PM / devfreq: Fix incorrect type issue.
  PM / devfreq: tegra: Update governor to use devfreq_update_stats()
  PM / devfreq: comments for get_dev_status usage updated
  PM / devfreq: drop comment about thermal setting max_freq
  PM / devfreq: cache the last call to get_dev_status()
  PM / devfreq: Drop unlikely before IS_ERR(_OR_NULL)
  PM / devfreq: exynos-ppmu: bit-wise operation bugfix.
  PM / devfreq: exynos-ppmu: Update documentation to support PPMUv2
  PM / devfreq: exynos-ppmu: Add the support of PPMUv2 for Exynos5433
  PM / devfreq: event: Remove incorrect property in exynos-ppmu DT binding

Pull virtio fixes and cleanups from Michael Tsirkin:
 "This fixes the virtio-test tool, and improves the error handling for
  virtio-ccw"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio/s390: handle failures of READ_VQ_CONF ccw
  tools/virtio: propagate V=X to kernel build
  vhost: move features to core
  tools/virtio: fix build after 4.2 changes

Pull KVM fixes from Paolo Bonzini:
 "Mostly stable material, a lot of ARM fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
  sched: access local runqueue directly in single_task_running
  arm/arm64: KVM: Remove 'config KVM_ARM_MAX_VCPUS'
  arm64: KVM: Remove all traces of the ThumbEE registers
  arm: KVM: Disable virtual timer even if the guest is not using it
  arm64: KVM: Disable virtual timer even if the guest is not using it
  arm/arm64: KVM: vgic: Check for !irqchip_in_kernel() when mapping resources
  KVM: s390: Replace incorrect atomic_or with atomic_andnot
  arm: KVM: Fix incorrect device to IPA mapping
  arm64: KVM: Fix user access for debug registers
  KVM: vmx: fix VPID is 0000H in non-root operation
  KVM: add halt_attempted_poll to VCPU stats
  kvm: fix zero length mmio searching
  kvm: fix double free for fast mmio eventfd
  kvm: factor out core eventfd assign/deassign logic
  kvm: don't try to register to KVM_FAST_MMIO_BUS for non mmio eventfd
  KVM: make the declaration of functions within 80 characters
  KVM: arm64: add workaround for Cortex-A57 erratum #852523
  KVM: fix polling for guest halt continued even if disable it
  arm/arm64: KVM: Fix PSCI affinity info return value for non valid cores
  arm64: KVM: set {v,}TCR_EL2 RES1 bits
  ...

Some of the device files are required to be user accessible for PSM while
most should remain accessible only by root.

Add a parameter to hfi1_cdev_init which controls if the user should have access
to this device which places it in a different class with the appropriate
devnode callback.

In addition set the devnode call back for the existing class to be a bit more
explicit for those permissions.

Finally remove the unnecessary null check before class_destroy
Tested-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Haralanov, Mitko (mitko.haralanov@intel.com)
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

We are shifting by the _MASK macros instead of the _SHIFT ones.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

I added spaces around operators so it matches kernel style because
normally "-1ULL" is a number and " - 1" is a subtract operation.  Also
removed some superflous "ULL" types so "1ULL" becomes "1".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The cinfo struct has a hole after the last struct member so we need to
zero it out.  Otherwise we disclose some uninitialized stack data.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

mutex_trylock() returns zero on failure, not EBUSY.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

__get_txreq() returns an ERR_PTR() but this checks for NULL so it would
oops on failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The boolean tests should have been or-ed.
Reported-by: David Binderman <dcb314@hotmail.com>
Reviewed-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>