An error occurred fetching the project authors.
- 05 Oct, 2010 40 commits
-
-
Helmut Schaa authored
rt61pci and rt2800 devices can use up to 7 different rates per tx frame. However, the device uses a global fallback table. Hence, the rc algortihm cannot specify multiple rates to try but the device is able to report multiple rates (based on the retry table). Specify that behavior by correctly setting max_report_rates and max_rates. This makes rt2x00 and minstrel play nicer together. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Some drivers cannot handle multiple retry rates specified by the rc algorithm but instead use their own retry table (for example rt2800). However, if such a device registers itself with a max_rates value of 1 the rc algorithm cannot make use of the extended information the device can provide about retried rates. On the other hand, if a device registers itself with a max_rates value > 1 the rc algorithm assumes that the device can handle multi rate retries. Fix this issue by introducing another hw parameter max_report_rates that can be set to a different value then max_rates to indicate if a device is capable of reporting more rates then specified in max_rates. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Since rt2x00 USB devices have no chance to know when a beacon was sent out in AP mode currently all broad- and multicast traffic is buffered in mac80211 but never sent out at all. Unfortunately we have no chance in sending the traffic out after a DTIM beacon due to hw limitations. Hence, instead of never sending the buffered traffic out better send it out immediately. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Reported-by: Lauri Hintsala <lauri.hintsala@bluegiga.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Add the register definition CH_BUSY_STA_SEC for reading the busy time on the secondary channel in HT40 mode. Also update the comments about channel busy/idle time registers to express the used unit. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ivo van Doorn authored
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Make use of the IEEE80211_TX_RC_DUP_DATA flag to duplicate a transmission with legacy rates to both 20Mhz channels if set. Also update the related comment in rt2800.h to describe the behavior of the BW_40 flag for legacy rates. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
During rx, rt2x00lib calls rt2800pci_fill_rxdone to read the RX descriptor. At that time the skb is already dma unmapped but no new skb was dma mapped for this entry again. However, rt2800pci_fill_rxdone also moves the hw rx queue index, marking this entry to be available for reuse. Since no new skb was dma mapped and also the previous skb was unmapped this might lead to strange hw behavior. To fix this issue move the hw rx queue index increment to rt2800pci_clear_entry where a new skb was already dma mapped and can be safely used by the hw. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Since HT protection is now configurable via mac80211 we don't need this special case for PCI devices anymore. The HT protection config will be overwritten as soon as mac80211 sends us a HT operation mode. Hence, bring the HT MM40 protection config in sync with the other HT protection registers and initialize it to no protection. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Update the HT operation mode when mac80211 sends it to us and set the different HT protection modes and rates accordingly. For now only use CTS-to-self with OFDM 24M or CCK 11M when protection is required. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Fix a check for dynamic SM PS mode in the STAs HT caps. Since a value of 3 means "SM PS disabled" the previous check assumed in that case that "dynamic SM PS" was enabled and as such prefixed every MCS>7 frame with a unnecessary RTS/CTS exchange. Also, the bit shift was done in the wrong direction. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
This patch changes the way tx status reports are handled by rt2800pci. Previously rt2800pci would sometimes lose tx status reports as the TX_STA_FIFO register is a fifo of 16 entries that can overflow in case we don't read it often/fast enough. Since interrupts are disabled in the device during the execution of the interrupt thread it happend sometimes under high network and CPU load that processing took too long and a few tx status reports were dropped by the hw. To fix this issue the TX_STA_FIFO register is read directly in the interrupt handler and stored in a kfifo which is large enough to hold all status reports of all used tx queues. To process the status reports a new tasklet txstatus_tasklet is used. Using the already used interrupt thread is not possible since we don't want to disable the TX_FIFO_STATUS interrupt while processing them and it is not possible to schedule the interrupt thread multiple times for execution. A tasklet instead can be scheduled multiple times which allows to leave the TX_FIFO_STATUS interrupt enabled while a previously scheduled tasklet is still executing. In short: All other interrupts are handled in the interrupt thread as before. Only the TX_FIFO_STATUS interrupt is partly handled in the interrupt handler and finished in the according tasklet. One drawback of this patch is that it duplicates some code from rt2800lib. However, that can be cleaned up in the future once the rt2800usb and rt2800pci tx status handling converge more. Using this patch on a Ralink RT3052 embedded board gives me a reliable wireless connection even under high CPU and network load. I've transferred several gigabytes without any queue lockups. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
rt2800 devices use parts of the pariwise key table to store the beacon frames for beacon 6 and 7. To not overwrite the beacon frame buffers limit the number of entries we store in the pairwise key table to 222. Also add some descriptive comments about this shared memory usage. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Christian Lamparter authored
Source: http://www.wikidevi.com/wiki/Intersil/p54/usb/windows Cc: <stable@kernel.org> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ben Greear authored
Includes pkts/bytes that may have had errors, and includes wireless headers when counting bytes. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ben Greear authored
This adds counters for tx and rx bytes, including any errored packets as well as all wireless headers. Signed-off-by: Ben Greear <greearb@candelatech.com> Acked-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bill Jordan authored
Initialize the rate table for WDS interfaces, and add cases to allow WDS packets to pass the xmit and receive tests. Signed-off-by: Bill Jordan <bjordan@rajant.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bill Jordan authored
Added a nl interface to set the peer bssid of a WDS interface. Signed-off-by: Bill Jordan <bjordan@rajant.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bill Jordan authored
Enable WDS for the ath9k driver. Signed-off-by: Bill Jordan <bjordan@rajant.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
On association to an AP, after receiving beacons, the beacon_crc value is set. The beacon_crc value is not reset in disassociation, but the BSS data may be expired at a later point. When associating again, it's possible that a beacon for the AP is not received, resulting in the beacon_ies to remain NULL. After association, further beacons will not update the beacon data, as the crc value of the beacon has not changed, and the beacon_crc still holds a value matching the beacon. The beacon_ies will remain forever null. One of the results of this is that WLAN power save cannot be entered, the STA will remain foreven in active mode. Fix this by adding a validation flag for the beacon_crc, which is cleared on association. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
Move ieee80211_scan_cancel() and all other related code to ieee80211_restart_work() as ieee80211_restart_hw() is intended to be callable from any context. Fix a bug that RTNL lock is not taken during ieee80211_cancel_scan(). Take local->mtx before WARN(test_bit(SCAN_HW_SCANNING, &local->scanning) to prevent the race condition with __ieee80211_start_scan() described here: http://marc.info/?l=linux-wireless&m=128516716810537&w=2Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
In the ath9k debugging feature 'wiphy' the current channel used by the station is incorrectly displayed.This is because the channels available are sequentially mapped from numbers 0 to 37.This mapping cannot be changed as the channel number is also used as an array index This fix solves the above problem by calculating the channel number from center frequency. Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
The percal struct and bitmask for the initial DC calibration are not used anywhere, so they can be removed. Signed-off-by: Felix Fietkau <nbd@openwrt.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Since the regulatory code touches the channel array, it needs to be copied for each device instance. That way the original channel array can also be made const. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org [all] Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Add missing unlocking of the wiphy in set_channel, and don't try to unlock a non-existing wiphy in set_cqm. Cc: stable@kernel.org [2.6.35+] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ben Greear authored
Support up to 4 virtual APs and as many virtual STA interfaces as desired. This patch is ported forward from a patch that Patrick McHardy did for me against 2.6.31. Signed-off-by: Ben Greear <greearb@candelatech.com> Acked-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
The net/cfg80211.h header file isn't exported to userspace, so there's no need for any kind of __KERNEL__ protection in it. If it was exported, everything else in it would need protection as well, not just the logging stuff ... Cc:Joe Perches <joe@perches.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Enable management frame transmission and subscribing to management frames through nl80211 in both cfg80211 and mac80211. Also update a few places that I forgot to update for P2P-client mode previously, and fix a small bug with non-action frames in this API. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
We can start restarting firmware or RF kill switch can be turned on during call to iwl_mac_add_interface(). That are normal working conditions, so do not print call trace, just print simple message instead. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ben Hutchings authored
The combined firmware ar9170.fw is preferred and supports all devices. References to the older two-stage firmware are unnecessary. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Some user space applications only want to display survey data for the operating channel, however there is no API to get that yet. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
common->ani.noise_floor is now only used for a similar redundant debug message similar to the one that was removed from ath9k_htc in an earlier patch. Remove it from ath9k as well now. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
It is unused aside from a single redundant debug message Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Christian Lamparter authored
The hardware rx-filter was essentially disabled, because of a serve, yet unidentifiable problem with iwlagn. Due to these circumstances the driver and mac80211 were left with the job of filtering. This is very unfortunate and has proven to be expensive in terms of latency, memory and load. Therefore the new 1.8.8.3 firmware introduces a flexible filtering infrastructure which allows the driver to offload some of the checks (FCS & PLCP crc check, RA match, control frame filter, etc...) whenever possible. Note: This patch also includes all changes to the shared headers files since the inclusion. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Christian Lamparter authored
This patch fixes an refcounting bug. Previously it was possible to corrupt the per-device recv. filter and monitor management counters when: iw dev wlanX set monitor [new flags] was issued on an active monitor interface. Acked-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ben Greear authored
Choose first available phyX name when creating phy devices. This means that reloading a wifi driver will not cause a change in the name of it's phy device. Also, allow users to rename a phy to any un-used name, including phy%d. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-