- 26 Sep, 2011 3 commits
-
-
Mohammed Shafi Shajakhan authored
proper dma_unmapping and freeing of skb's has to be done in the rx cleanup for EDMA chipsets when the device is unloaded and this also seems to address the following warning which shows up occasionally when the device is unloaded Call Trace: [<c0148cd2>] warn_slowpath_common+0x72/0xa0 [<c03b669c>] ? dma_debug_device_change+0x19c/0x200 [<c03b669c>] ? dma_debug_device_change+0x19c/0x200 [<c0148da3>] warn_slowpath_fmt+0x33/0x40 [<c03b669c>] dma_debug_device_change+0x19c/0x200 [<c0657f12>] notifier_call_chain+0x82/0xb0 [<c0171370>] __blocking_notifier_call_chain+0x60/0x90 [<c01713bf>] blocking_notifier_call_chain+0x1f/0x30 [<c044f594>] __device_release_driver+0xa4/0xc0 [<c044f647>] driver_detach+0x97/0xa0 [<c044e65c>] bus_remove_driver+0x6c/0xe0 [<c029af0b>] ? sysfs_addrm_finish+0x4b/0x60 [<c0450109>] driver_unregister+0x49/0x80 [<c0299f54>] ? sysfs_remove_file+0x14/0x20 [<c03c3ab2>] pci_unregister_driver+0x32/0x80 [<f92c2162>] ath_pci_exit+0x12/0x20 [ath9k] [<f92c8467>] ath9k_exit+0x17/0x36 [ath9k] [<c06523cd>] ? mutex_unlock+0xd/0x10 [<c018e27f>] sys_delete_module+0x13f/0x200 [<c02139bb>] ? sys_munmap+0x4b/0x60 [<c06547c5>] ? restore_all+0xf/0xf [<c0657a20>] ? spurious_fault+0xe0/0xe0 [<c01832f4>] ? trace_hardirqs_on_caller+0xf4/0x180 [<c065b863>] sysenter_do_call+0x12/0x38 ---[ end trace 16e1c1521c06bcf9 ]--- Mapped at: [<c03b7938>] debug_dma_map_page+0x48/0x120 [<f92ba3e8>] ath_rx_init+0x3f8/0x4b0 [ath9k] [<f92b5ae4>] ath9k_init_device+0x4c4/0x7b0 [ath9k] [<f92c2813>] ath_pci_probe+0x263/0x330 [ath9k] Signed-off-by:
Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Larry Finger authored
Driver rtl8192cu assigns a new struct rtl_tcb_desc object, but fails to clear it. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> [2.6.39+] Signed-off-by:
-
Johannes Berg authored
If iwl_scan_initiate() fails for any reason, priv->scan_request and priv->scan_vif are left dangling. This can lead to a crash later when iwl_bg_scan_completed() tries to run a pending scan request. In practice, this seems to be very rare due to the STATUS_SCANNING check earlier. That check, however, is wrong -- it should allow a scan to be queued when a reset/roc scan is going on. When a normal scan is already going on, a new one can't be issued by mac80211, so that code can be removed completely. I introduced this bug when adding off-channel support in commit 266af4c7. Cc: stable@kernel.org [3.0] Reported-by:
Peng Yan <peng.yan@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
-
- 21 Sep, 2011 4 commits
-
-
Jouni Malinen authored
Incorrect variable was used in validating the akm_suites array from NL80211_ATTR_AKM_SUITES. In addition, there was no explicit validation of the array length (we only have room for NL80211_MAX_NR_AKM_SUITES). This can result in a buffer write overflow for stack variables with arbitrary data from user space. The nl80211 commands using the affected functionality require GENL_ADMIN_PERM, so this is only exposed to admin users. Cc: stable@kernel.org Signed-off-by:
Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by:
-
Stanislaw Gruszka authored
iwlegacy version of fix: commit effd4d9a Author: Johannes Berg <johannes.berg@intel.com> Date: Thu Sep 15 11:46:52 2011 -0700 iwlagn: do not use interruptible waits Since the dawn of its time, iwlwifi has used interruptible waits to wait for synchronous commands and firmware loading. This leads to "interesting" bugs, because it can't actually handle the interruptions; for example when a command sending is interrupted it will assume the command completed fully, and then leave it pending, which leads to all kinds of trouble when the command finishes later. Since there's no easy way to gracefully deal with interruptions, fix the driver to not use interruptible waits. This at least fixes the error iwlagn 0000:02:00.0: Error: Response NULL in 'REPLY_SCAN_ABORT_CMD' I have seen in P2P testing, but it is likely that there are other errors caused by this. Cc: stable@kernel.org # 2.6.39+ Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Stanislaw Gruszka authored
iwlegacy version of fix: commit 282cdb32 Author: Johannes Berg <johannes.berg@intel.com> Date: Mon Sep 12 12:09:10 2011 -0700 iwlagn: fix command queue timeout If the command queue is constantly busy, which can happen in P2P, the hangcheck timer will frequently find a command in it and will eventually reset the device because nothing sets the timestamp for this queue when commands are processed. Fix this by setting the timestamp when a command completes. iwlegacy does not support P2P, but this patch fix possible unneeded hardware resets, hence is needed. Cc: stable@kernel.org # 2.6.39+ Signed-off-by:
-
Rajkumar Manoharan authored
During the endurance testing, rx frames are not getting DMAd from MAC whereas pcu rx frame counters are getting updated properly. As per systems team input updated the initval to fix rx dma stuck issue. Cc: stable@kernel.org Signed-off-by:
Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by:
-
- 19 Sep, 2011 2 commits
-
-
Manual Munz authored
In ad-hoc mode, driver b43 does not issue beacons. Signed-off-by:
Manual Munz <freifunk@somakoma.de> Tested-by:
-
-
- 17 Sep, 2011 3 commits
-
-
Jurgen Kramer authored
Today I noticed that the usb bluetooth adapter (BCM2046B1) on my 2011 mac mini was not working. I've created a patch to get it going. Signed-off-by:
Jurgen Kramer <gtmkramer@xs4all.nl> Signed-off-by:
Gustavo F. Padovan <padovan@profusion.mobi>
-
Pieter-Augustijn Van Malleghem authored
This patch against current git adds the hardware ID for the Apple MacBookAir4,1, released in July 2011. The device features a BCM2046 USB chip. The patch was inspired by the previous modifications adding support for the MacBookAir3,x. Signed-off-by:
Pieter-Augustijn Van Malleghem <p-a@scarlet.be> Signed-off-by:
-
Chen Ganir authored
Reordered the BT ST channel registration, to make sure that the event channel is registered before all others. This prevents a situation where incoming events may cause kernel panic in the ST driver if the event channel is not yet registered to handle incoming events.In addition, the deregistration of the channels was also modified, to be in the reversed order of the registration, to allow the event channel to be the last one unregistered. Signed-off-by:
Chen Ganir <chen.ganir@ti.com> Signed-off-by:
-
- 16 Sep, 2011 6 commits
-
-
Don Fry authored
This patch reverts commit 9b768832 which was introduced in 2.6.38-rc1. It works around a problem where the iwlagn driver stimulates a bug crashing (requiring power cycle to recover) some APs under heavy traffic. CC: stable@kernel.org #2.6.39, #3.0.0 #3.1.0 Signed-off-by:
Don Fry <donald.h.fry@intel.com> SIgned-off-by:
-
Rajkumar Manoharan authored
The scan request received from cfg80211_connect do not have proper rate mast. So the probe request sent on each channel do not have proper the supported rates ie. Cc: stable@kernel.org Reviewed-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Larry Finger authored
The eeprom data is stored in little-endian order in the rt2x00 library. As it was converted to cpu order in the read routines, the data need to be converted to LE on a big-endian platform. Signed-off-by:
-
Larry Finger authored
Using gcc 4.4.5 on a Powerbook G4 with a PPC cpu, a complicated if statement results in incorrect flow, whereas the equivalent switch statement works correctly. Signed-off-by:
-
Stanislaw Gruszka authored
This fix regression introduced by: commit: ecb44335 Author: Stanislaw Gruszka <sgruszka@redhat.com> Date: Fri Aug 12 14:00:59 2011 +0200 mac80211: fix suspend/resume races with unregister hw Above commit add rtnl_lock() into wiphy_register(), what cause deadlock when initializing ipw2x00 driver, which itself call wiphy_register() from register_netdev() internal callback with rtnl mutex taken. To fix move wiphy_register() outside register_netdev(). This solution have side effect of not creating /sys/class/net/wlanX/phy80211 link, but that's a minor issue we can live with. Bisected-by:
Witold Baryluk <baryluk@smp.if.uj.edu.pl> Bisected-by:
Michael Witten <mfwitten@gmail.com> Tested-by:
-
Rajkumar Manoharan authored
During the association, the regulatory is updated by country IE that reaps the previously found beacons. The impact is that after a STA disconnects *or* when for any reason a regulatory domain change happens the beacon hint flag is not cleared therefore preventing future beacon hints to be learned. This is important as a regulatory domain change or a restore of regulatory settings would set back the passive scan and no-ibss flags on the channel. This is the right place to do this given that it covers any regulatory domain change. Cc: stable@kernel.org Reviewed-by:
Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by:
Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by:
-
- 15 Sep, 2011 1 commit
-
-
Oliver Neukum authored
The checks for HCI_INQUIRY and HCI_MGMT were in the wrong order, so that second scans always failed. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
- 13 Sep, 2011 6 commits
-
-
Johannes Berg authored
If the command queue is constantly busy, which can happen in P2P, the hangcheck timer will frequently find a command in it and will eventually reset the device because nothing sets the timestamp for this queue when commands are processed. Fix this by setting the timestamp when a command completes. Cc: stable@kernel.org #2.6.39, #3.0.0 #3.1.0 Signed-off-by:
-
Johannes Berg authored
Alexander reported a strange crash in iwlagn that Meenakshi and Wey couldn't reproduce. I just ran into the same issue and tracked it down to stack corruption. This fixes it. The problem was introduced in commit 4b8b99b6e650d0527f3a123744b7459976581d14 Author: Wey-Yi Guy <wey-yi.w.guy@intel.com> Date: Fri Jul 8 14:29:48 2011 -0700 iwlagn: radio sensor offset in le16 format Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com> Cc: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Reported-by:Alexander Diewald <alex@diewald.cc> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
when the device is yanked out ath_pci_remove starts doing the cleanups, unregistering the hardware etc. so we should bail out immediately when we get drv_flush callback from mac80211 when the card is being unplugged. the panic occurs after we had associated to an AP. EIP: 0060:[<fb315b00>] EFLAGS: 00010246 CPU: 0 EIP is at ath_reset+0xa0/0x1c0 [ath9k] EAX: 00000000 EBX: 000697c0 ECX: 00000002 EDX: f3c3ccf0 ESI: 00000000 EDI: 00000000 EBP: f43e7b78 ESP: f43e7b50 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 Process kworker/u:2 (pid: 182, ti=f43e6000 task=f3c3c7c0 task.ti=f43e6000) Stack: 0000002a 00000000 00000000 003e7b78 0000000f eaaa8500 ffffffea eaaa97c0 eaaaa000 00000001 f43e7ba8 fb315d23 f99e7721 ecece680 eaaac738 eaaa8500 eaaaa020 000000c8 000000c8 00000000 eaaa8d58 eaaa8500 f43e7bd0 fb080b29 Call Trace: [<fb315d23>] ath9k_flush+0x103/0x170 [ath9k] [<fb080b29>] __ieee80211_recalc_idle+0x2c9/0x400 [mac80211] [<fb080c8e>] ieee80211_recalc_idle+0x2e/0x60 [mac80211] [<fb07aa73>] ieee80211_mgd_deauth+0x173/0x210 [mac80211] [<fb084559>] ieee80211_deauth+0x19/0x20 [mac80211] [<f99dda53>] __cfg80211_mlme_deauth+0xf3/0x140 [cfg80211] [<c0633d00>] ? __mutex_lock_common+0x1f0/0x380 [<f99e1b5d>] __cfg80211_disconnect+0x18d/0x1f0 [cfg80211] [<f99c8199>] cfg80211_netdev_notifier_call+0x159/0x5c0 [cfg80211] [<c0608a64>] ? packet_notifier+0x174/0x1f0 [<c0639202>] notifier_call_chain+0x82/0xb0 [<c0170d8f>] raw_notifier_call_chain+0x1f/0x30 [<c053b86c>] call_netdevice_notifiers+0x2c/0x60 [<c0182184>] ? trace_hardirqs_on_caller+0xf4/0x180 [<c053b8ec>] __dev_close_many+0x4c/0xd0 [<c053ba2d>] dev_close_many+0x6d/0xc0 [<c053bb53>] rollback_registered_many+0x93/0x1c0 [<c018221b>] ? trace_hardirqs_on+0xb/0x10 [<c053bc95>] unregister_netdevice_many+0x15/0x50 [<fb07f83b>] ieee80211_remove_interfaces+0x7b/0xb0 [mac80211] [<fb06a14b>] ieee80211_unregister_hw+0x4b/0x110 [mac80211] [<fb311a4a>] ath9k_deinit_device+0x3a/0x60 [ath9k] [<fb31eed6>] ath_pci_remove+0x46/0x90 [ath9k] [<c03b4ac4>] pci_device_remove+0x44/0x100 [<c043eb54>] __device_release_driver+0x64/0xb0 [<c043ec67>] device_release_driver+0x27/0x40 [<c043deeb>] bus_remove_device+0x7b/0xa0 [<c043c491>] device_del+0xf1/0x180 [<c043c530>] device_unregister+0x10/0x20 [<c03afafe>] pci_stop_bus_device+0x6e/0x80 [<c03afb72>] pci_remove_bus_device+0x12/0xa0 [<c03c2f29>] pciehp_unconfigure_device+0x89/0x180 [<c0181e54>] ? mark_held_locks+0x64/0x100 [<c063390f>] ? __mutex_unlock_slowpath+0xaf/0x140 [<c03c1f84>] pciehp_disable_slot+0x64/0x1b0 [<c03c2850>] pciehp_power_thread+0xd0/0x100 [<c0164ad0>] ? process_one_work+0x100/0x4d0 [<c0164b4c>] process_one_work+0x17c/0x4d0 [<c0164ad0>] ? process_one_work+0x100/0x4d0 [<c03c2780>] ? queue_interrupt_event+0xa0/0xa0 [<c01662bb>] worker_thread+0x13b/0x320 [<c018221b>] ? trace_hardirqs_on+0xb/0x10 [<c0166180>] ? manage_workers+0x1e0/0x1e0 [<c016a654>] kthread+0x84/0x90 [<c016a5d0>] ? __init_kthread_worker+0x60/0x60 [<c063d106>] kernel_thread_helper+0x6/0x10 Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by:
-
Johannes Berg authored
Since my commit 34e89507 ("mac80211: allow station add/remove to sleep") there is a race in mac80211 when it clears the TIM bit because a sleeping station disconnected, the spinlock isn't held around the relevant code any more. Use the right API to acquire the spinlock correctly. Cc: stable@kernel.org [2.6.34+] Signed-off-by:
-
George authored
The driver fails to clear encryption keys making it impossible to switch connections. Signed-off-by:
George <george0505@realtek.com> Signed-off-by:
-
George authored
The driver fails to connect to 802.11n-enabled APs. The patch fixes Bug #42262. Signed-off-by:
-
- 30 Aug, 2011 1 commit
-
-
Felix Fietkau authored
ADC calibrations cannot run on 5 GHz with fast clock enabled. They need to be disabled, otherwise they'll hang and IQ mismatch calibration will not be run either. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Reported-by:
Adrian Chadd <adrian@freebsd.org> Cc: stable@kernel.org Signed-off-by:
-
- 29 Aug, 2011 2 commits
-
-
Stanislaw Gruszka authored
When trying to connect to 5GHz we can provide negative index to mac80211 what trigger BUG_ON. Reason of iwl-3945-rs malfunction on 5GHz is unknown and needs further investigation. For now, to do not trigger a bug, correct value and just print WARNING. Address bug: https://bugzilla.redhat.com/show_bug.cgi?id=730653Reported-and-tested-by:
Jan Teichmann <jan.teichmann@gmail.com> Cc: stable@kernel.org Signed-off-by:
-
Rajkumar Manoharan authored
The commit 172805ad overwirtes additional clock settings of AR9330 to all AR9300 chips. Cc: stable@kernel.org Signed-off-by:
-
- 24 Aug, 2011 2 commits
-
-
Mohammed Shafi Shajakhan authored
this callback is called during suspend/resume and also via iw command. it configures parameters like sifs, slottime, acktimeout in ath9k_hw_init_global_settings where few REG_READ, REG_RMW are also done and hence the need for PS wrappers Cc: stable@kernel.org Signed-off-by:
-
Alexey Khoroshilov authored
If is_main_vif(ar, vif) reports that we have to fall back to software encryption, we goto err_softw; before locking ar->mutex. As a result, we have unprotected call to carl9170_set_operating_mode and unmatched mutex_unlock. The patch fix the issue by adding mutex_lock before goto. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: <stable@kernel.org> Acked-By:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
-
- 23 Aug, 2011 3 commits
-
-
Luciano Coelho authored
After commit 5a865bad, we require a separate value to indicate the number of supported SSIDs in scheduled scans. This patch adds a proper value to the wl12xx driver. This fixes a regression in 3.1-rc3 where scheduled scans were not working properly with the wl12xx driver. Signed-off-by:
Luciano Coelho <coelho@ti.com> Signed-off-by:
-
Ido Yariv authored
wl1271_sdio_power_on checks if the return value of pm_runtime_get_sync is non-zero, and if so bails out. However, pm_runtime_get_sync can return a positive number which does not suggest an error has occurred. This is problematic for two reasons: 1. The function will needlessly bail out without decrementing back the runtime PM reference counter. 2. wl1271_power_on only checks if wl1271_power_on return value is negative. This means that wl1271_power_on will continue even if wl1271_sdio_power_on bailed out. As a result, sdio transactions will be initiated without properly enabling the sdio function and claiming the host. This could even lead to a kernel panic. Fix this by only checking that the return value of pm_runtime_get_sync is non-negative. Signed-off-by:
Ido Yariv <ido@wizery.com> Acked-by:
-
Ido Yariv authored
The testmode NVS push command is no longer in use. In addition, it has several implementation issues that prevent it from working correctly: 1. wl1271_tm_cmd_configure relies on wl->chip.id being set. However, since the device was not necessarily booted by the time the function is called, wl->chip.id will be initialized to 0. 2. The NVS file is fetched by calling request_firmware() before it is possible to push an NVS file. 3. The maximum allowed size of nl binary payloads is not sufficient for pushing NVS files. 4. Pushing 128x NVS files will always fail due to a bug in the validation code. 5. In case the pushed NVS file is found invalid, the mutex will be kept locked and the nvs member will become a dangling pointer. Since this feature is not being used, remove it completely instead of fixing it. Signed-off-by:
-
- 22 Aug, 2011 5 commits
-
-
David Woodhouse authored
Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Acked-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Senthil Balasubramanian authored
Due to some recent optimization done in the way the mac address bytes are written into the OTP memory, some AR9485 chipsets were forced to use the first byte from the eeprom template and the remaining bytes are read from OTP. AR9485 happens to use generic eeprom template which has 0x1 as the first byte causes issues in bringing up the card. So fixed the eeprom template accordingly to address the issue. Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Signed-off-by:
Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by:
-
Stanislaw Gruszka authored
When hibernating ->resume may not be called by usb core, but disconnect and probe instead, so we do not increase the counter after decreasing it in ->supend. As a result we free memory early, and get crash when unplugging usb dongle. BUG: unable to handle kernel paging request at 6b6b6b9f IP: [<c06909b0>] driver_sysfs_remove+0x10/0x30 *pdpt = 0000000034f21001 *pde = 0000000000000000 Pid: 20, comm: khubd Not tainted 3.1.0-rc1-wl+ #20 LENOVO 6369CTO/6369CTO EIP: 0060:[<c06909b0>] EFLAGS: 00010202 CPU: 1 EIP is at driver_sysfs_remove+0x10/0x30 EAX: 6b6b6b6b EBX: f52bba34 ECX: 00000000 EDX: 6b6b6b6b ESI: 6b6b6b6b EDI: c0a0ea20 EBP: f61c9e68 ESP: f61c9e64 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 Process khubd (pid: 20, ti=f61c8000 task=f6138270 task.ti=f61c8000) Call Trace: [<c06909ef>] __device_release_driver+0x1f/0xa0 [<c0690b20>] device_release_driver+0x20/0x40 [<c068fd64>] bus_remove_device+0x84/0xe0 [<c068e12a>] ? device_remove_attrs+0x2a/0x80 [<c068e267>] device_del+0xe7/0x170 [<c06d93d4>] usb_disconnect+0xd4/0x180 [<c06d9d61>] hub_thread+0x691/0x1600 [<c0473260>] ? wake_up_bit+0x30/0x30 [<c0442a39>] ? complete+0x49/0x60 [<c06d96d0>] ? hub_disconnect+0xd0/0xd0 [<c06d96d0>] ? hub_disconnect+0xd0/0xd0 [<c0472eb4>] kthread+0x74/0x80 [<c0472e40>] ? kthread_worker_fn+0x150/0x150 [<c0809b3e>] kernel_thread_helper+0x6/0x10 Cc: stable@kernel.org Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
Stanislaw Gruszka authored
Do not call ->suspend, ->resume methods after we unregister wiphy. Also delete sta_clanup timer after we finish wiphy unregister to avoid this: WARNING: at lib/debugobjects.c:262 debug_print_object+0x85/0xa0() Hardware name: 6369CTO ODEBUG: free active (active state 0) object type: timer_list hint: sta_info_cleanup+0x0/0x180 [mac80211] Modules linked in: aes_i586 aes_generic fuse bridge stp llc autofs4 sunrpc cpufreq_ondemand acpi_cpufreq mperf ext2 dm_mod uinput thinkpad_acpi hwmon sg arc4 rt2800usb rt2800lib crc_ccitt rt2x00usb rt2x00lib mac80211 cfg80211 i2c_i801 iTCO_wdt iTCO_vendor_support e1000e ext4 mbcache jbd2 sd_mod crc_t10dif sr_mod cdrom yenta_socket ahci libahci pata_acpi ata_generic ata_piix i915 drm_kms_helper drm i2c_algo_bit video [last unloaded: microcode] Pid: 5663, comm: pm-hibernate Not tainted 3.1.0-rc1-wl+ #19 Call Trace: [<c0454cfd>] warn_slowpath_common+0x6d/0xa0 [<c05e05e5>] ? debug_print_object+0x85/0xa0 [<c05e05e5>] ? debug_print_object+0x85/0xa0 [<c0454dae>] warn_slowpath_fmt+0x2e/0x30 [<c05e05e5>] debug_print_object+0x85/0xa0 [<f8a808e0>] ? sta_info_alloc+0x1a0/0x1a0 [mac80211] [<c05e0bd2>] debug_check_no_obj_freed+0xe2/0x180 [<c051175b>] kfree+0x8b/0x150 [<f8a126ae>] cfg80211_dev_free+0x7e/0x90 [cfg80211] [<f8a13afd>] wiphy_dev_release+0xd/0x10 [cfg80211] [<c068d959>] device_release+0x19/0x80 [<c05d06ba>] kobject_release+0x7a/0x1c0 [<c07646a8>] ? rtnl_unlock+0x8/0x10 [<f8a13adb>] ? wiphy_resume+0x6b/0x80 [cfg80211] [<c05d0640>] ? kobject_del+0x30/0x30 [<c05d1a6d>] kref_put+0x2d/0x60 [<c05d056d>] kobject_put+0x1d/0x50 [<c08015f4>] ? mutex_lock+0x14/0x40 [<c068d60f>] put_device+0xf/0x20 [<c069716a>] dpm_resume+0xca/0x160 [<c04912bd>] hibernation_snapshot+0xcd/0x260 [<c04903df>] ? freeze_processes+0x3f/0x90 [<c049151b>] hibernate+0xcb/0x1e0 [<c048fdc0>] ? pm_async_store+0x40/0x40 [<c048fe60>] state_store+0xa0/0xb0 [<c048fdc0>] ? pm_async_store+0x40/0x40 [<c05d0200>] kobj_attr_store+0x20/0x30 [<c0575ea4>] sysfs_write_file+0x94/0xf0 [<c051e26a>] vfs_write+0x9a/0x160 [<c0575e10>] ? sysfs_open_file+0x200/0x200 [<c051e3fd>] sys_write+0x3d/0x70 [<c080959f>] sysenter_do_call+0x12/0x28 Cc: stable@kernel.org Signed-off-by:
-
John W. Linville authored
-
- 13 Aug, 2011 2 commits
-
-
Emmanuel Grumbach authored
This bug has been introduced by: d5934110 Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Date: Mon Jul 11 10:48:51 2011 +0300 iwlagn: simplify the bus architecture Revert part of the buggy patch: dev_get_drvdata will now return iwl_priv as it did before the patch. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
This reverts commit cc1a93e6. This fix introduced a bug: bad pointer in unload. Signed-off-by:
-
