The code in rfbi.c tried to get the omapdss platform_device via a static
member defined in dispc.c, leading to a compile error. The same
platform_device is available through rfbi-struct.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>

I was observing the following error messages on my OMAP1 based Amstrad Delta
board when first changing from text to graphics mode or vice versa after the
LCD display had been blanked:
	omapfb omapfb: timeout waiting for FRAME DONE
with a followup error message while unblanking it back:
	omapfb omapfb: resetting (status 0xffffffb2,reset count 1)
As a visible result, image pixels happened to be shifted by a few bits,
giving wrong colors.

Examining the code, I found that this problem occures when an OMAP1 internal
LCD controller is disabled from omap_lcdc_suspend() and then a subsequent
omap_lcdc_setup_plane() calls disable_controller() again. This potentially
error provoking behaviour is triggered by the lcdc.update_mode flag being kept
at OMAP_AUTO_UPDATE, regardless of the controller and panel being suspended.

This patch tries to correct the problem by replacing both omap_lcdc_suspend()
and omap_lcdc_resume() function bodies with single calls to
omap_lcdc_set_update_mode() with a respective OMAP_UPDATE_DISABLE or
OMAP_AUTO_UPDATE argument. As a result, exactly the same lower level
operations are performed, with addition of changing the lcdc.update_mode flag
to a value better suited for the controller state. This prevents any further
calls to disable_controller() from omap_lcdc_setup_plane() while the display
is suspended.

Created against linux-2.6.34-rc7.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>

.. and thus endeth the merge window.

* 'slub/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  SLUB: Allow full duplication of kmalloc array for 390
  slub: move kmem_cache_node into it's own cacheline

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  mutex: Fix optimistic spinning vs. BKL

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf tui: Fix last use_browser problem related to .perfconfig
  perf symbols: Add the build id cache to the vmlinux path
  perf tui: Reset use_browser if stdout is not a tty
  ring-buffer: Move zeroing out excess in page to ring buffer code
  ring-buffer: Reset "real_end" when page is filled

This partially reverts commit 4ec37de8
("[IA64] Fix build breakage"), since the commit that made it necessary
got reverted earlier (see commit 35926ff5, 'Revert "cpusets:
randomize node rotor used in cpuset_mem_spread_node()"')

Even if we ever re-introduce this, there is no reason to make
__node_random be some architecture-specific function.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  mm: export generic_pipe_buf_*() to modules
  fuse: support splice() reading from fuse device
  fuse: allow splice to move pages
  mm: export remove_from_page_cache() to modules
  mm: export lru_cache_add_*() to modules
  fuse: support splice() writing to fuse device
  fuse: get page reference for readpages
  fuse: use get_user_pages_fast()
  fuse: remove unneeded variable

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-kconfig:
  kconfig: Hide error output in find command in streamline_config.pl
  kconfig: Fix typo in comment in streamline_config.pl
  kconfig: Make a variable local in streamline_config.pl

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (47 commits)
  mfd: Rename twl5031 sih modules
  mfd: Storage class for timberdale should be before const qualifier
  mfd: Remove unneeded and dangerous clearing of clientdata
  mfd: New AB8500 driver
  gpio: Fix inverted rdc321x gpio data out registers
  mfd: Change rdc321x resources flags to IORESOURCE_IO
  mfd: Move pcf50633 irq related functions to its own file.
  mfd: Use threaded irq for pcf50633
  mfd: pcf50633-adc: Fix potential race in pcf50633_adc_sync_read
  mfd: Fix pcf50633 bitfield logic in interrupt handler
  gpio: rdc321x needs to select MFD_CORE
  mfd: Use menuconfig for quicker config editing
  ARM: AB3550 board configuration and irq for U300
  mfd: AB3550 core driver
  mfd: AB3100 register access change to abx500 API
  mfd: Renamed ab3100.h to abx500.h
  gpio: Add TC35892 GPIO driver
  mfd: Add Toshiba's TC35892 MFD core
  mfd: Delay to mask tsc irq in max8925
  mfd: Remove incorrect wm8350 kfree
  ...

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  DMAENGINE: DMA40 U8500 platform configuration
  DMA: PL330: Add dma api driver

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/qib: Remove DCA support until feature is finished
  IB/qib: Use a single txselect module parameter for serdes tuning
  IB/qib: Don't rely on (undefined) order of function parameter evaluation
  IB/ucm: Use memdup_user()
  IB/qib: Fix undefined symbol error when CONFIG_PCI_MSI=n

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
  quota: Convert quota statistics to generic percpu_counter
  ext3 uses rb_node = NULL; to zero rb_root.
  quota: Fixup dquot_transfer
  reiserfs: Fix resuming of quotas on remount read-write
  pohmelfs: Remove dead quota code
  ufs: Remove dead quota code
  udf: Remove dead quota code
  quota: rename default quotactl methods to dquot_
  quota: explicitly set ->dq_op and ->s_qcop
  quota: drop remount argument to ->quota_on and ->quota_off
  quota: move unmount handling into the filesystem
  quota: kill the vfs_dq_off and vfs_dq_quota_on_remount wrappers
  quota: move remount handling into the filesystem
  ocfs2: Fix use after free on remount read-only

Fix up conflicts in fs/ext4/super.c and fs/ufs/file.c

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, cpufeature: Unbreak compile with gcc 3.x
  x86, pat: Fix memory leak in free_memtype
  x86, k8: Fix section mismatch for powernowk8_exit()
  lib/atomic64_test: fix missing include of linux/kernel.h
  x86: remove last traces of quicklist usage
  x86, setup: Phoenix BIOS fixup is needed on Dell Inspiron Mini 1012
  x86: "nosmp" command line option should force the system into UP mode
  arch/x86/pci: use kasprintf
  x86, apic: ack all pending irqs when crashed/on kexec

If there's only one CPU online when disable_nonboot_cpus() is called,
the error variable will not be initialized and that may lead to
erroneous behavior.  Fix this issue by initializing error in
disable_nonboot_cpus() as appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix a bunch of new rapidio kernel-doc warnings:

Warning(include/linux/rio.h:123): No description found for parameter 'comp_tag'
Warning(include/linux/rio.h:123): No description found for parameter 'phys_efptr'
Warning(include/linux/rio.h:123): No description found for parameter 'em_efptr'
Warning(include/linux/rio.h:123): No description found for parameter 'pwcback'
Warning(include/linux/rio.h:247): No description found for parameter 'set_domain'
Warning(include/linux/rio.h:247): No description found for parameter 'get_domain'
Warning(drivers/rapidio/rio-scan.c:1133): No description found for parameter 'rdev'
Warning(drivers/rapidio/rio-scan.c:1133): Excess function parameter 'port' description in 'rio_init_em'
Warning(drivers/rapidio/rio.c:349): No description found for parameter 'rdev'
Warning(drivers/rapidio/rio.c:349): Excess function parameter 'mport' description in 'rio_request_inb_pwrite'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'port'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'local'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'destid'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'hopcount'
Warning(drivers/rapidio/rio.c:393): Excess function parameter 'rdev' description in 'rio_mport_get_physefb'
Warning(drivers/rapidio/rio.c:845): Excess function parameter 'local' description in 'rio_std_route_clr_table'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  parisc: Call pagefault_disable/pagefault_enable in kmap_atomic/kunmap_atomic
  parisc: Remove unnecessary macros from entry.S
  parisc: LWS fixes for syscall.S
  parisc: Delete unnecessary nop's in entry.S
  parisc: Avoid interruption in critical region in entry.S
  parisc: invoke oom-killer from page fault
  parisc: clear floating point exception flag on SIGFPE signal
  parisc: Use of align_frame provides stack frame.

This reverts commit 0ac0c0d0, which
caused cross-architecture build problems for all the wrong reasons.
IA64 already added its own version of __node_random(), but the fact is,
there is nothing architectural about the function, and the original
commit was just badly done. Revert it, since no fix is forthcoming.
Requested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: clean up on forwarded aborted mds request
  ceph: fix leak of osd authorizer
  ceph: close out mds, osd connections before stopping auth
  ceph: make lease code DN specific
  fs/ceph: Use ERR_CAST
  ceph: renew auth tickets before they expire
  ceph: do not resend mon requests on auth ticket renewal
  ceph: removed duplicated #includes
  ceph: avoid possible null dereference
  ceph: make mds requests killable, not interruptible
  sched: add wait_for_completion_killable_timeout

Commit 756dee75 ("SLUB: Get rid of dynamic DMA
kmalloc cache allocation") makes S390 run out of kmalloc caches.  Increase the
number of kmalloc caches to a safe size.

Cc: <stable@kernel.org> [ .33 and .34 ]
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>

Based on the generic implementation of kmap_atomic and kunmap_atomic,
we should call pagefault_disable and pagefault_enable in our PA8000
implementation.

The define for kmap_atomic_prot was also missing, and I updated
kmap_atomic_pfn to use the generic implementation because of the
change to kmap_atomic.

I believe that this change is needed to fix the fork copy-on-write
bug.
Signed-off-by: John David Anglin <dave.anglin@nrc-cnrc.gc.ca>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

The EXTR, DEP and DEPI macros are unnecessary.  There are PA 1.X
pneumonics available with the same functionality, and the DEP and DEPI
macros conflict with assembler pneumonics.

Tested on a variety of 32 and 64-bit systems.
Signed-off-by: John David Anglin <dave.anglin@nrc-cnrc.gc.ca>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

1) Gate immediately and save a branch.
2) Fix off by one error in checking entry number.
3) Use sr7 instead of sr3 in error return path as sr3 might not
   contain correct value.
4) Enable locking on UP systems to prevent incorrect operation of
   the cas_action critical region on page faults.

Tested on several systems, including UP c3750 with 2.6.33.2 kernel.
Signed-off-by: John David Anglin <dave.anglin@nrc-cnrc.gc.ca>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

Signed-off-by: John David Anglin <dave.anglin@nrc-cnrc.gc.ca>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

Signed-off-by: John David Anglin <dave.anglin@nrc-cnrc.gc.ca>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

As explained in commit 1c0fe6e3, we want to call the architecture independent
oom killer when getting an unexplained OOM from handle_mm_fault, rather than
simply killing current.

Cc: linux-parisc@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

Clear the floating point exception flag before returning to
user space. This is needed, else the libc trampoline handler
may hit the same SIGFPE again while building up a trampoline
to a signal handler.

Fixes debian bug #559406.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

Any assembly constant generated with the use of
align_frame includes size for a full stack frame.
Signed-off-by: Carlos O'Donell <carlos@systemhalted.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (26 commits)
  ALSA: snd-usb-caiaq: Bump version number to 1.3.21
  ALSA: Revert "ALSA: snd-usb-caiaq: Set default input mode of A4DJ"
  ALSA: snd-usb-caiaq: Simplify single case to an 'if'
  ALSA: snd-usb-caiaq: Restore 'Control vinyl' input mode on A4DJ
  ALSA: hda: Use LPIB for a Shuttle device
  ALSA: hda: Add support for another Lenovo ThinkPad Edge in conexant codec
  ALSA: hda: Use LPIB for Sony VPCS11V9E
  ALSA: usb-audio: fix feature unit parser for UAC2
  ALSA: asihpi - Minor code cleanup
  ALSA: asihpi - Add support for new ASI8800 family
  ALSA: asihpi - Fix bug preventing outstream_write preload from happening
  ALSA: asihpi - Fix imbalanced lock path in hw_message
  ALSA: asihpi - Remove support for old ASI8800 family
  ALSA: asihpi - Add hd radio blend functions
  ALSA: asihpi - Remove unused io map functions
  ALSA: usb-audio: add support for UAC2 pitch control
  ALSA: usb-audio: parse UAC2 endpoint descriptors correctly
  ALSA: usb-audio: fix return values
  ALSA: usb-audio: parse more format descriptors with structs
  sound: Add missing spin_unlock
  ...

Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Do not explicity set the default input mode. Use the hardware default
of mode 0 ('Control vinyl'), which is now available.

This reverts commit e3ca4c99.
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

After removing code, only one case remains. So use an 'if' instead.
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This feature was undocumented on early A4DJ units. It is indicated
by lighting both the 'line' and 'phono' lamps at the same time.
Newer units document this and the newer Windows drivers enable this
for all units, so restore the functionality.

This patch simplifies the code and changes the mode mapping to match
the A8DJ, favouring simpler code and consistency over keeping the
existing mapping.

Both 'Control vinyl' and 'Phono' input modes enable the hardware
preamp. The difference is the input impedance.

This reverts commit 9a9527ed.
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

BugLink: https://launchpad.net/bugs/551949

Symptom: On the reporter's Shuttle device, using PulseAudio in Ubuntu
10.04 LTS results in "popping clicking" audio with the PA crashing
shortly thereafter.

Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, adjust the HDA device's volume with PulseAudio.

Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Christian Mehlis <mehlis@inf.fu-berlin.de>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

If an mds request is aborted (timeout, SIGKILL), it is left registered to
keep our state in sync with the mds.  If we get a forward notification,
though, we know the request didn't succeed and we can unregister it
safely.  We were trying to resend it, but then bailing out (and not
unregistering) in __do_request.
Signed-off-by: Sage Weil <sage@newdream.net>

Release the ceph_authorizer when releasing osd state.
Signed-off-by: Sage Weil <sage@newdream.net>

The auth module (part of the mon_client) is needed to free any
ceph_authorizer(s) used by the mds and osd connections.  Flush the msgr
workqueue before stopping monc to ensure that the destroy_authorizer
auth op is available when those connections are closed out.
Signed-off-by: Sage Weil <sage@newdream.net>