This patch adds the core support for switching and managing the SVE
architectural state of user tasks.

Calls to the existing FPSIMD low-level save/restore functions are
factored out as new functions task_fpsimd_{save,load}(), since SVE
now dynamically may or may not need to be handled at these points
depending on the kernel configuration, hardware features discovered
at boot, and the runtime state of the task.  To make these
decisions as fast as possible, const cpucaps are used where
feasible, via the system_supports_sve() helper.

The SVE registers are only tracked for threads that have explicitly
used SVE, indicated by the new thread flag TIF_SVE.  Otherwise, the
FPSIMD view of the architectural state is stored in
thread.fpsimd_state as usual.

When in use, the SVE registers are not stored directly in
thread_struct due to their potentially large and variable size.
Because the task_struct slab allocator must be configured very
early during kernel boot, it is also tricky to configure it
correctly to match the maximum vector length provided by the
hardware, since this depends on examining secondary CPUs as well as
the primary.  Instead, a pointer sve_state in thread_struct points
to a dynamically allocated buffer containing the SVE register data,
and code is added to allocate and free this buffer at appropriate
times.

TIF_SVE is set when taking an SVE access trap from userspace, if
suitable hardware support has been detected.  This enables SVE for
the thread: a subsequent return to userspace will disable the trap
accordingly.  If such a trap is taken without sufficient system-
wide hardware support, SIGILL is sent to the thread instead as if
an undefined instruction had been executed: this may happen if
userspace tries to use SVE in a system where not all CPUs support
it for example.

The kernel will clear TIF_SVE and disable SVE for the thread
whenever an explicit syscall is made by userspace.  For backwards
compatibility reasons and conformance with the spirit of the base
AArch64 procedure call standard, the subset of the SVE register
state that aliases the FPSIMD registers is still preserved across a
syscall even if this happens.  The remainder of the SVE register
state logically becomes zero at syscall entry, though the actual
zeroing work is currently deferred until the thread next tries to
use SVE, causing another trap to the kernel.  This implementation
is suboptimal: in the future, the fastpath case may be optimised
to zero the registers in-place and leave SVE enabled for the task,
where beneficial.

TIF_SVE is also cleared in the following slowpath cases, which are
taken as reasonable hints that the task may no longer use SVE:
 * exec
 * fork and clone

Code is added to sync data between thread.fpsimd_state and
thread.sve_state whenever enabling/disabling SVE, in a manner
consistent with the SVE architectural programmer's model.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Alex Bennée <alex.bennee@linaro.org>
[will: added #include to fix allnoconfig build]
[will: use enable_daif in do_sve_acc]
Signed-off-by: Will Deacon <will.deacon@arm.com>

To enable the kernel to use SVE, SVE traps from EL1 to EL2 must be
disabled.  To take maximum advantage of the hardware, the full
available vector length also needs to be enabled for EL1 by
programming ZCR_EL2.LEN.  (The kernel will program ZCR_EL1.LEN as
required, but this cannot override the limit set by ZCR_EL2.)

This patch makes the appropriate changes to the EL2 early setup
code.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

This patch defines the representation that will be used for the SVE
register state in the signal frame, and implements support for
saving and restoring the SVE registers around signals.

The same layout will also be used for the in-kernel task state.

Due to the variability of the SVE vector length, it is not possible
to define a fixed C struct to describe all the registers.  Instead,
Macros are defined in sigcontext.h to facilitate access to the
parts of the structure.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

This patch adds CONFIG_ARM64_SVE to control building of SVE support
into the kernel, and adds a stub predicate system_supports_sve() to
control conditional compilation and runtime SVE support.

system_supports_sve() just returns false for now: it will be
replaced with a non-trivial implementation in a later patch, once
SVE support is complete enough to be enabled safely.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Manipulating the SVE architectural state, including the vector and
predicate registers, first-fault register and the vector length,
requires the use of dedicated instructions added by SVE.

This patch adds suitable assembly functions for saving and
restoring the SVE registers and querying the vector length.
Setting of the vector length is done as part of register restore.

Since people building kernels may not all get an SVE-enabled
toolchain for a while, this patch uses macros that generate
explicit opcodes in place of assembler mnemonics.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

The SVE architecture adds some system registers, ID register fields
and a dedicated ESR exception class.

This patch adds the appropriate definitions that will be needed by
the kernel.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

The existing FPSIMD context switch code contains a couple of
instances of {set,clear}_ti_thread(task_thread_info(task)).  Since
there are thread flag manipulators that operate directly on
task_struct, this verbosity isn't strictly needed.

For consistency, this patch simplifies the affected calls.  This
should have no impact on behaviour.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Currently, armv8_deprected.c takes charge of the "abi" sysctl
directory, which makes life difficult for other code that wants to
register sysctls in the same directory.

There is a "new" [1] sysctl registration interface that removes the
need to define ctl_tables for parent directories explicitly, which
is ideal here.

This patch ports register_insn_emulation_sysctl() over to the
register_sysctl() interface and removes the redundant ctl_table for
"abi".
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>

[1] fea478d4 (sysctl: Add register_sysctl for normal sysctl
users)
The commit message notes an intent to port users of the
pre-existing interfaces over to register_sysctl(), though the
number of users of the new interface currently appears negligible.
Signed-off-by: Will Deacon <will.deacon@arm.com>

The EFI runtime services ABI permits calls to EFI to clobber
certain FPSIMD/NEON registers, as per the AArch64 procedure call
standard.

Saving/restoring the clobbered registers around such calls needs
KERNEL_MODE_NEON, but the dependency is missing from Kconfig.

This patch adds the missing dependency.

This will aid bisection of the patches implementing support for the
ARM Scalable Vector Extension (SVE).
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Currently, a guest kernel sees the true CPU feature registers
(ID_*_EL1) when it reads them using MRS instructions.  This means
that the guest may observe features that are present in the
hardware but the host doesn't understand or doesn't provide support
for.  A guest may legimitately try to use such a feature as per the
architecture, but use of the feature may trap instead of working
normally, triggering undef injection into the guest.

This is not a problem for the host, but the guest may go wrong when
running on newer hardware than the host knows about.

This patch hides from guest VMs any AArch64-specific CPU features
that the host doesn't support, by exposing to the guest the
sanitised versions of the registers computed by the cpufeatures
framework, instead of the true hardware registers.  To achieve
this, HCR_EL2.TID3 is now set for AArch64 guests, and emulation
code is added to KVM to report the sanitised versions of the
affected registers in response to MRS and register reads from
userspace.

The affected registers are removed from invariant_sys_regs[] (since
the invariant_sys_regs handling is no longer quite correct for
them) and added to sys_reg_desgs[], with appropriate access(),
get_user() and set_user() methods.  No runtime vcpu storage is
allocated for the registers: instead, they are read on demand from
the cpufeatures framework.  This may need modification in the
future if there is a need for userspace to customise the features
visible to the guest.

Attempts by userspace to write the registers are handled similarly
to the current invariant_sys_regs handling: writes are permitted,
but only if they don't attempt to change the value.  This is
sufficient to support VM snapshot/restore from userspace.

Because of the additional registers, restoring a VM on an older
kernel may not work unless userspace knows how to handle the extra
VM registers exposed to the KVM user ABI by this patch.

Under the principle of least damage, this patch makes no attempt to
handle any of the other registers currently in
invariant_sys_regs[], or to emulate registers for AArch32: however,
these could be handled in a similar way in future, as necessary.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Currently sys_rt_sigreturn() verifies that the base sigframe is
readable, but no similar check is performed on the extra data to
which an extra_context record points.

This matters because the extra data will be read with the
unprotected user accessors.  However, this is not a problem at
present because the extra data base address is required to be
exactly at the end of the base sigframe.  So, there would need to
be a non-user-readable kernel address within about 59K
(SIGFRAME_MAXSZ - sizeof(struct rt_sigframe)) of some address for
which access_ok(VERIFY_READ) returns true, in order for sigreturn
to be able to read kernel memory that should be inaccessible to the
user task.  This is currently impossible due to the untranslatable
address hole between the TTBR0 and TTBR1 address ranges.

Disappearance of the hole between the TTBR0 and TTBR1 mapping
ranges would require the VA size for TTBR0 and TTBR1 to grow to at
least 55 bits, and either the disabling of tagged pointers for
userspace or enabling of tagged pointers for kernel space; none of
which is currently envisaged.

Even so, it is wrong to use the unprotected user accessors without
an accompanying access_ok() check.

To avoid the potential for future surprises, this patch does an
explicit access_ok() check on the extra data space when parsing an
extra_context record.

Fixes: 33f08261 ("arm64: signal: Allow expansion of the signal frame")
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

A couple of FPSIMD exception handling functions that are called
from entry.S are currently not annotated as such.

This is not a big deal since asmlinkage does nothing on arm/arm64,
but fixing the annotations is more consistent and may help avoid
future surprises.

This patch adds appropriate asmlinkage annotations for
do_fpsimd_acc() and do_fpsimd_exc().
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Currently the regset API doesn't allow for the possibility that
regsets (or at least, the amount of meaningful data in a regset)
may change in size.

In particular, this results in useless padding being added to
coredumps if a regset's current size is smaller than its
theoretical maximum size.

This patch adds a get_size() function to struct user_regset.
Individual regset implementations can implement this function to
return the current size of the regset data.  A regset_size()
function is added to provide callers with an abstract interface for
determining the size of a regset without needing to know whether
the regset is dynamically sized or not.

The only affected user of this interface is the ELF coredump code:
This patch ports ELF coredump to dump regsets with their actual
size in the coredump.  This has no effect except for new regsets
that are dynamically sized and provide a get_size() implementation.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dmitry Safonov <dsafonov@virtuozzo.com>
Cc: H. J. Lu <hjl.tools@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

When the PMU driver is built as a module, the perf expects the
pmu->module to be valid, so that the driver is prevented from
being unloaded while it is in use. Fix the CCN pmu driver to
fill in this field.

Fixes: a33b0daa ("bus: ARM CCN PMU driver")
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

When the PMU driver is built as a module, the perf expects the
pmu->module to be valid, so that the driver is prevented from
being unloaded while it is in use. Fix the SPE pmu driver to
fill in this field.

Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Function graph does not work currently when CONFIG_DYNAMIC_TRACE is not
set. This is because ftrace_function_trace is not always set to ftrace_stub
when function_graph is in use.

Do not skip checking of graph tracer functions when ftrace_function_trace
is set.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Today SError is taken using the inv_entry macro that ends up in
bad_mode.

SError can be used by the RAS Extensions to notify either the OS or
firmware of CPU problems, some of which may have been corrected.

To allow this handling to be added, add a do_serror() C function
that just panic()s. Add the entry.S boiler plate to save/restore the
CPU registers and unmask debug exceptions. Future patches may change
do_serror() to return if the SError Interrupt was notification of a
corrected error.
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Wang Xiongfeng <wangxiongfengi2@huawei.com>
[Split out of a bigger patch, added compat path, renamed, enabled debug
 exceptions]
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Following our 'dai' order, irqs should be processed with debug and
serror exceptions unmasked.

Add a helper to unmask these two, (and fiq for good measure).
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

el0_sync also unmasks exceptions on a case-by-case basis, debug exceptions
are enabled, unless this was a debug exception. Irqs are unmasked for
some exception types but not for others.

el0_dbg should run with everything masked to prevent us taking a debug
exception from do_debug_exception. For the other cases we can unmask
everything. This changes the behaviour of fpsimd_{acc,exc} and el0_inv
which previously ran with irqs masked.

This patch removed the last user of enable_dbg_and_irq, remove it.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

el1_sync unmasks exceptions on a case-by-case basis, debug exceptions
are unmasked, unless this was a debug exception. IRQs are unmasked
for instruction and data aborts only if the interupted context had
irqs unmasked.

Following our 'dai' order, el1_dbg should run with everything masked.
For the other cases we can inherit whatever we interrupted.

Add a macro inherit_daif to set daif based on the interrupted pstate.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

enable_step_tsk is the only user of disable_dbg, which doesn't respect
our 'dai' order for exception masking. enable_step_tsk may enable
single-step, so previously needed to mask debug exceptions to prevent us
from single-stepping kernel_exit. enable_step_tsk is called at the end
of the ret_to_user loop, which has already masked all exceptions so this
is no longer needed.

Remove disable_dbg, add a comment that enable_step_tsk's caller should
have masked debug.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

To take RAS Exceptions as quickly as possible we need to keep SError
unmasked as much as possible. We need to mask it during kernel_exit
as taking an error from this code will overwrite the exception-registers.

Adding a naked 'disable_daif' to kernel_exit causes a performance problem
for micro-benchmarks that do no real work, (e.g. calling getpid() in a
loop). This is because the ret_to_user loop has already masked IRQs so
that the TIF_WORK_MASK thread flags can't change underneath it, adding
disable_daif is an additional self-synchronising operation.

In the future, the RAS APEI code may need to modify the TIF_WORK_MASK
flags from an SError, in which case the ret_to_user loop must mask SError
while it examines the flags.

Disable all exceptions for return to EL1. For return to EL0 get the
ret_to_user loop to leave all exceptions masked once it has done its
work, this avoids an extra pstate-write.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Remove the local_{async,fiq}_{en,dis}able macros as they don't respect
our newly defined order and are only used to set the flags for process
context when we bring CPUs online.

Add a helper to do this. The IRQ flag varies as we want it masked on
the boot CPU until we are ready to handle interrupts.
The boot CPU unmasks SError during early boot once it can print an error
message. If we can print an error message about SError, we can do the
same for FIQ. Debug exceptions are already enabled by __cpu_setup(),
which has also configured MDSCR_EL1 to disable MDE and KDE.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Currently SError is always masked in the kernel. To support RAS exceptions
using SError on hardware with the v8.2 RAS Extensions we need to unmask
SError as much as possible.

Let's define an order for masking and unmasking exceptions. 'dai' is
memorable and effectively what we have today.

Disabling debug exceptions should cause all other exceptions to be masked.
Masking SError should mask irq, but not disable debug exceptions.
Masking irqs has no side effects for other flags. Keeping to this order
makes it easier for entry.S to know which exceptions should be unmasked.

FIQ is never expected, but we mask it when we mask debug exceptions, and
unmask it at all other times.

Given masking debug exceptions masks everything, we don't need macros
to save/restore that bit independently. Remove them and switch the last
caller over to use the daif calls.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

There are a few places where we want to mask all exceptions. Today we
do this in a piecemeal fashion, typically we expect the caller to
have masked irqs and the arch code masks debug exceptions, ignoring
serror which is probably masked.

Make it clear that 'mask all exceptions' is the intention by adding
helpers to do exactly that.

This will let us unmask SError without having to add 'oh and SError'
to these paths.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

After commit 9e8e865b ("arm64: unify idmap removal"), we no need to
flush tlb in suspend.c, so the included file tlbflush.h can be removed.
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Commit 42dbf54e ("arm64: consistently log ESR and page table")
dumps page table entries for user faults hitting do_bad entries in the
fault handler table. Whilst this shouldn't really happen in practice,
it's not beyond the realms of possibility if e.g. running an old kernel
on a new CPU.

Generally, we want to avoid exposing physical addresses under the control
of userspace (see commit bf396c09 ("arm64: mm: don't print out page
table entries on EL0 faults")), so walk the page tables only on exceptions
from EL1.
Reported-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

The vdso tries to check for a NULL res pointer in __kernel_clock_getres,
but only checks the lower 32 bits as is uses CBZ on the W register the
res pointer is held in.

Thus, if the res pointer happened to be aligned to a 4GiB boundary, we'd
spuriously skip storing the timespec to it, while returning a zero error code
to the caller.

Prevent this by checking the whole pointer, using CBZ on the X register
the res pointer is held in.

Fixes: 9031fefd ("arm64: VDSO support")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Andrew Pinski <apinski@cavium.com>
Reported-by: Mark Salyzyn <salyzyn@android.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Upon upgrading to binutils 2.27, we found that our lz4 and gzip
compressed kernel images were significantly larger, resulting is 10ms
boot time regressions.

As noted by Rahul:
"aarch64 binaries uses RELA relocations, where each relocation entry
includes an addend value. This is similar to x86_64.  On x86_64, the
addend values are also stored at the relocation offset for relative
relocations. This is an optimization: in the case where code does not
need to be relocated, the loader can simply skip processing relative
relocations.  In binutils-2.25, both bfd and gold linkers did this for
x86_64, but only the gold linker did this for aarch64.  The kernel build
here is using the bfd linker, which stored zeroes at the relocation
offsets for relative relocations.  Since a set of zeroes compresses
better than a set of non-zero addend values, this behavior was resulting
in much better lz4 compression.

The bfd linker in binutils-2.27 is now storing the actual addend values
at the relocation offsets. The behavior is now consistent with what it
does for x86_64 and what gold linker does for both architectures.  The
change happened in this upstream commit:
https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=1f56df9d0d5ad89806c24e71f296576d82344613
Since a bunch of zeroes got replaced by non-zero addend values, we see
the side effect of lz4 compressed image being a bit bigger.

To get the old behavior from the bfd linker, "--no-apply-dynamic-relocs"
flag can be used:
$ LDFLAGS="--no-apply-dynamic-relocs" make
With this flag, the compressed image size is back to what it was with
binutils-2.25.

If the kernel is using ASLR, there aren't additional runtime costs to
--no-apply-dynamic-relocs, as the relocations will need to be applied
again anyway after the kernel is relocated to a random address.

If the kernel is not using ASLR, then presumably the current default
behavior of the linker is better. Since the static linker performed the
dynamic relocs, and the kernel is not moved to a different address at
load time, it can skip applying the relocations all over again."

Some measurements:

$ ld -v
GNU ld (binutils-2.25-f3d35cf6) 2.25.51.20141117
                    ^
$ ls -l vmlinux
-rwxr-x--- 1 ndesaulniers eng 300652760 Oct 26 11:57 vmlinux
$ ls -l Image.lz4-dtb
-rw-r----- 1 ndesaulniers eng 16932627 Oct 26 11:57 Image.lz4-dtb

$ ld -v
GNU ld (binutils-2.27-53dd00a1) 2.27.0.20170315
                    ^
pre patch:
$ ls -l vmlinux
-rwxr-x--- 1 ndesaulniers eng 300376208 Oct 26 11:43 vmlinux
$ ls -l Image.lz4-dtb
-rw-r----- 1 ndesaulniers eng 18159474 Oct 26 11:43 Image.lz4-dtb

post patch:
$ ls -l vmlinux
-rwxr-x--- 1 ndesaulniers eng 300376208 Oct 26 12:06 vmlinux
$ ls -l Image.lz4-dtb
-rw-r----- 1 ndesaulniers eng 16932466 Oct 26 12:06 Image.lz4-dtb

By Siqi's measurement w/ gzip:
binutils 2.27 with this patch (with --no-apply-dynamic-relocs):
Image 41535488
Image.gz 13404067

binutils 2.27 without this patch (without --no-apply-dynamic-relocs):
Image 41535488
Image.gz 14125516

Any compression scheme should be able to get better results from the
longer runs of zeros, not just GZIP and LZ4.

10ms boot time savings isn't anything to get excited about, but users of
arm64+compression+bfd-2.27 should not have to pay a penalty for no
runtime improvement.
Reported-by: Gopinath Elanchezhian <gelanchezhian@google.com>
Reported-by: Sindhuri Pentyala <spentyala@google.com>
Reported-by: Wei Wang <wvw@google.com>
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Rahul Chaudhry <rahulchaudhry@google.com>
Suggested-by: Siqi Lin <siqilin@google.com>
Suggested-by: Stephen Hines <srhines@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: added comment to Makefile]
Signed-off-by: Will Deacon <will.deacon@arm.com>

The generic pte_access_permitted() implementation only checks for
pte_present() (together with the write permission where applicable).
However, for both kernel ptes and PROT_NONE mappings pte_present() also
returns true on arm64 even though such mappings are not user accessible.
Additionally, arm64 now supports execute-only user permission
(PROT_EXEC) which is implemented by clearing the PTE_USER bit.

With this patch the arm64 implementation of pte_access_permitted()
checks for the PTE_VALID and PTE_USER bits together with writable access
if applicable.

Cc: <stable@vger.kernel.org>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

PSTATE.Q only exists for AArch32, which can be referred to using
COMPAT_PSR_Q_BIT. Remove PSR_Q_BIT, since the native bit doesn't exist
in the architecture
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

We can decode the PSTATE easily enough, so pretty-print it in register
dumps.
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Printing raw pointer values in backtraces has potential security
implications and are of questionable value anyway.

This patch follows x86's lead and removes the "Exception stack:" dump
from kernel backtraces, as well as converting PC/LR values to symbols
such as "sysrq_handle_crash+0x20/0x30".
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

When we take a fault we can't handle, we try to dump some relevant
information, but we're not consistent about doing so.

In do_mem_abort(), we log the full ESR, but don't dump a page table
walk. In __do_kernel_fault, we dump an attempted decoding of the ESR
(but not the ESR itself) along with a page table walk.

Let's try to make things more consistent by dumping the full ESR in
mem_abort_decode(), and having do_mem_abort dump a page table walk. The
existing dump of the ESR in do_mem_abort() is rendered redundant, and
removed.
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Julien Thierry <julien.thierry@arm.com>
Cc: Kristina Martsenko <kristina.martsenko@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Currently ASM_BUG() and its constituent macros define local
assembler labels 0, 1 and 2 internally, which carries a high risk
of clash with callers' labels and consequent mis-assembly.

This patch gives the labels a big random offset to minimise the
chance of such errors.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Software Step exception is missing after stepping a trapped instruction.

Ensure SPSR.SS gets set to 0 after emulating/skipping a trapped instruction
before doing ERET.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[will: replaced AARCH32_INSN_SIZE with 4]
Signed-off-by: Will Deacon <will.deacon@arm.com>

Literal values are being used to set single stepping in mdscr from assembly
code. There are already existing defines representing those values, use
those instead of the literal values.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

__memcpy_{to,from}io fall back to byte-at-a-time copying if both the
source and destination pointers are not 8-byte aligned. Since one of the
pointers always points at normal memory, this is unnecessary and
detrimental to performance, so only do byte copying until we hit an 8-byte
boundary for the device pointer.

This change was motivated by performance issues in the pstore driver.
On a test platform, measuring probe time for pstore, console buffer
size of 1/4MB and pmsg of 1/2MB, was in the 90-107ms region. Change
managed to reduce it to 10-25ms, an improvement in boot time.

Cc: Kees Cook <keescook@chromium.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Mark Salyzyn <salyzyn@android.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Merge in ARM PMU and perf updates for 4.15:

  - Support for the Statistical Profiling Extension
  - Support for Hisilicon's SoC PMU
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm_pmu interrupts are maked as PERCPU even when these are not local
physical interrupts to a single CPU. When using non-local interrupts,
interrupts marked as PERCPU will not get freed not disabled properly
by the PMU driver.

Check if interrupts are local to a single CPU with PERCPU_DEVID since
this is what the PMU driver really needs to know.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>