Firmware doesn't report a complete and
ready-to-use vht cap. Instead the driver is
supposed to fill in the missing bits related to
number of chains.

This effectively increases Compressed Steering
Number and Number of Sounding Dimensions in
AssocReq frames for devices with more than one RF
chain and should improve TxBF performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The command was truncated so the parameter value
was seen in fw as 0. This caused U-APSD enabled
stations to be misconfigured and mistreated by AP.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Allow user to configure the duty cycle upto 100%. Since thermal
mitigation algorithm is running in user space, remove the driver
level limitation and let the user to control the temperature.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When WEP keys are uploaded it's possible that
there are stations associated already (e.g. when
merging) without any keys. Static WEP needs an
explicit per-peer key upload.

Make sure to re-upload wep keys if necessary.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When running 802.1x WEP keys must be installed
without pairwise-groupwise swap (which is
necessary for static WEP).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This has been missed while adding the QCA6174 support.
As in the last time, without advertising the firmware files
as needed (or optional) for ath10k, these won't be built into
ram disk for instance.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

qca6174 with wmi-tlv firmware uses offloaded
beaconing scheme (i.e. templates). This requires a
little different approach when implementing CSA.

Add missing code to update CS count and report CSA
completion to mac80211. Without it channel switch
was never finished.

To avoid races during interface teardown data_lock
has been used to protect is_up and is_started so
they can be compared against before scheduling
count down work.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The current SKID length configuration causes firmware
to reject peer creation for not able to allocate
AST entries for peers. This issue is observed when
least significant 3 bytes are used ramdomly to create
client MAC addresses.

AST table SKID length configuration is increased to
maximum value to fix this issue.
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Certain radar types such as FCC radar type 5 are using chirp
in their pulses, hence looking up the chirp status will enhance
to avoid false radar detection.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Firmware reports chirp status in phy error event if it's detected
and the chirp status is valuable to distinguish radar types.
So save it to use for DFS parttern detector.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Some of radar types such as FCC radar type 5 require
to look up chirp in pulse to detect genuine radar and
it will prevent DFS channels from false radar detection.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Having lower number of copy engine entries for target to host
WMI ring is causing drops in receiving management frames. This
issue is observed during max clients (128 clients) stress testing.
While bursting deauthentication frames from simulated clients,
approx. 70% of frames are getting dropped due to lower ring entries.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Driver for PCIe core requires PCI to be enabled, however we shouldn't
require it for the whole bus. Someone may be not interested in extra
PCI devices and what's more there are SoCs without any PCI at all (like
BCM5356C0, BCM5357*, BCM47186B0). For more details see Kconfig "help".
Please note this patch doesn't allow disabling PCI drivers yet, as it
requires more work on calls to bcma_core_pci_* functions.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

These functions are not exported nor used anywhere, so there is no
reason to put them in public headers.
Also drop unused bcma_chipco_(suspend|resume).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We were providing declarations but actual code was compiled only with
CONFIG_BCMA_HOST_PCI set. This could result in:
ERROR: "bcma_host_pci_down" [drivers/net/wireless/brcm80211/brcmsmac/brcmsmac.ko] undefined!
ERROR: "bcma_host_pci_up" [drivers/net/wireless/brcm80211/brcmsmac/brcmsmac.ko] undefined!
ERROR: "bcma_host_pci_down" [drivers/net/wireless/b43/b43.ko] undefined!
ERROR: "bcma_host_pci_up" [drivers/net/wireless/b43/b43.ko] undefined!
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

bcma also needs PCI, just like IOMEM and DMA, so let it depend on PCI,
or will cause building break for allmodconfig under c6x:

    CC [M]  drivers/bcma/driver_pcie2.o
  drivers/bcma/driver_pcie2.c: In function 'bcma_core_pcie2_up':
  drivers/bcma/driver_pcie2.c:196:8: error: implicit declaration of function 'pcie_set_readrq' [-Werror=implicit-function-declaration]
    err = pcie_set_readrq(dev, pcie2->reqsize);
          ^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Major changes in ath10k:

* qca6174: enable STA transmit beamforming (TxBF) support
* disable multi-vif power save by default

Not all firmware revisions have a proper
multi-interface client powersaving implementation,
e.g. qca6174 WLAN.RM.2.0-00073.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

qca6184 WLAN.RM.2.0-00073 has a bug in sta
powersave state machine and requires peer param to
be poked to enable the powersave.

Calling this unconditionally should be safe for
other chips/firmwares.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

During wmm tests changing wmm parameters did not change anything.
This was because of mismatch in WMM params per vdev command.
WMM params per vdev uses different command structure than wmm params
per pdev command.

Patch concerns qca6174.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

qca6174 WLAN.RM.2.0-00073 firmware uses full rx
reordering offload and delivers Rx via a new HTT
event. The event however is incorrectly generated
in firmware and becomes overly long (with trailing
garbage). This was hitting defined CE buffer limit
that was programmed to the device and caused
device to crash upon busier Rx traffic.

Increasing the CE buffer limit for HTT Rx pipe to
2KBytes seems to be enough to workaround this
problem.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Just like on BCM47XX arch, BCM5301X also has ChipCommon with IRQ for
GPIOs. Now we have interrupts working on BCM5301X we can finally make
use of it. This has been successfully tested on 5 different devices
(Buffalo, Luxul, Netgear).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When using a BCM4318 in a PCMCIA format, I get a startup message that the
device uses backplane revision 0xF000000. Next a WARNING is logged. Despite
the message, the device works fine, This patch silences the warning.

Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

cppcheck detected a buffer overflow:

[drivers/net/wireless/ath/wil6210/debugfs.c:634]: (error) Width 8
  given in format string (no. 1) is larger than destination buffer
  'cmd[8]', use %7s to prevent overflowing it.

For the current %8s sscanf we require cmd to be 9 chars long
so increase it by 1 byte to prevent the sscan overflow (rather
than reduce the %8s specifier to %7s as cppcheck recommends).
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

* ath9k_mci_update_rssi() is required only for
  cards that use MCI scheme. Make sure that it
  is not called for 3-wire cards.

* Call ath9k_ps_wakeup() early since register
  accesses are made in ath9k_mci_update_rssi().

* Fix usage of btcoex_lock to handle no_stomp_timer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Make sure that the btcoex timers are started/stopped
properly for both 3-wire and MCI schemes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When disabling BTCOEX, clearing the wlanactive gpio line
is required only for pre-AR9003 cards.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Commit "ath9k_hw: remove ATH_BTCOEX_CFG_MCI" removed
MCI as a separate coex scheme, but we need it to
avoid fiddling with GPIO registers during
ath9k_init_btcoex() that are meant only for 3-wire
cards.

Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The MCI configuration values are assigned
in ath9k_hw_btcoex_init_mci() which are used
by the MCI reset routine. When initializing
BTCOEX/MCI, ath_mci_setup() ends up using
uninitialized data. Fix this by setting up
the configuration parameters before issuing
a MCI reset.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath_init_btcoex_timer() always returns 0, so
checking for error conditions is not required.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add HAL_DEF_WOWLAN case in rtl92cu_get_hw_reg
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Features which are device specific are already updated in
interface specific initialization e.g. register_dev.
We should not initialize them in mwifiex_init_adapter();
else this would overwrite earlier settings.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

From the indenting, it seems like the READ_NEXT_PAIR() was supposed to
be inside the while loop.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The # flag in %X means print a 0X prefix. Remove the extra 0x prefix.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In order to add per-vif TX power capability cap per-packet TX power to vif
configured power if the latter is lower than per-rate TX power and mac80211
per-frame power. Use vif TX power if TPC has been disabled for current the
interface
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Configure the HW with highest TX power among all vif when HW TPC has been
enabled in order to add support to per-vif TX power capability. Use lowest
configured power among all interfaces when TPC is disabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>