Florian Fainelli says:

====================
net: dsa: bcm_sf2: Add support for CFP statistics

The Broadcom SF2 switch has a Compact Field Processor (CFP) which not
only can perform matching + action, but also counts the number of times
a rule has been hit. This is invaluable while debugging when/if rules
are not matched.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When the source and destination port of a CFP rule match, we must set
the loopback bit enable to allow that, otherwise the frame is discarded.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return CFP policer statistics (Green, Yellow or Red) as part of the
standard ethtool statistics. This helps debug when CFP rules may not be
hit (0 counter).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for adding CFP statistics, we will need to overlay the
standard B53 statistics, so create specific bcm_sf2_sw_* functions to
call into their b53_common.c counterpart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We no longer need a dedicated statistics mutex since we leverage
b53_common for statistics now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The link status value latches link-down events. To get the current
status we read the register twice in genphy_update_link(). There's
a potential risk that we miss a link-down event in polling mode.
This may cause issues if the user e.g. connects his machine to a
different network.

On the other hand reading the latched value may cause issues in
interrupt mode. Following scenario:

- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
  down and link-down info is latched.
- After aneg has finished link goes up and triggers an interrupt.
  Interrupt handler reads link status, means it reads the latched
  "link is down" info. But there won't be another interrupt as long
  as link stays up, therefore phylib will never recognize that link
  is up.

Deal with both scenarios by reading the register twice in interrupt
mode only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new compatibility string for this product. It's using
at91sam9260-macb layout but has a newer hardware revision: it's safer
to use its own string.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the compatibility sting documentation for sam9x60 10/100 interface.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This removes a line left while adding the correct compatibility string for
sama5d3 10/100 interface. Now use the "atmel,sama5d3-macb" string.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Implement periodic ERP rehash

Currently, an ERP set is created for each region according to rules
inserted and order of their insertion. However that might lead to
suboptimal ERP sets and possible unnecessary spillage into C-TCAM.
This patchset aims to fix this problem and introduces periodical checking
of used ERP sets and in case a better ERP set is possible for the given
set of rules, it rehashes the region to use the better ERP set.

Patch 1 prepares devlink params infra in order to fix the
        init/fini sequences.
Patch 2 implements hints infra in objagg library.
Patch 3 fixes a typo
Patch 4 adds number of root objects directly into objagg stats.
Patches 5-7 do split of multiple structs in Spectrum TCAM code.
Patch 8 introduces initial implementation of ERP rehash logic,
         according to objagg hints.
Patch 9 adds hints priv passing trought the layers.
Patch 10 adds multi field into PAGT reg. (new patch)
Patch 11 implements actual region rules migration in TCAM code.
Patch 12 adds a devlink param so user is able to control
         rehash interval.
Patch 13 adds couple of tracepoints in order to track
         rehash procedures.
Patch 14 adds a simple selftest to test region rehash.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Track the basic codepaths of delta rehash handling,
using mlxsw tracepoints.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As vregion rehash is happening in delayed work, add some visibility to
the process using a few tracepoints.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expose new driver-specific "acl_region_rehash_interval" devlink param
which would allow user to alter default ACL region rehash interval.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the hints are returned, the migration should be started. For that to
happen, there is a need to create a second physical region in TCAM with
new ERP set by passing the hints and then move chunk by chunk,
entry by entry.

During the transition, two lookups will occur. One in old region and
another in new region. The highest priority rule will be chosen.

In an unlikely case that the migration will fail and also rollback to
original region will fail the vregion will become in bad state.
Everything will work, only no future rehash will be possible. In a
follow-up work, this can be resolved by trying to resume the rollback
in delayed work and repair the vregion.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For Spectrum-2 this allows parallel lookups in multiple regions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hints priv comes from ERP code and it is possible to obtain it from
TCAM code. Add arg to appropriate functions so the hints
priv could be passed back down to ERP code. Pass NULL now as the
follow-up patches would pass an actual hints priv pointer.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce an initial implementation of rehash logic in ERP code.
Currently, the rehash is considered as needed only in case number of
roots in the hints is smaller than the number of roots actually in use.
In that case return hints pointer and let it be obtained through the
callpath through the Spectrum-2 TCAM op.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do the split of entry struct so the new entry struct is related to the
actual HW entry, whereas ventry struct is a SW abstration of that.
This split prepares possibility for ventry to hold 2 HW entries which
is needed for region ERP rehash flow.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do the split of chunk struct so the new chunk struct is related to the
actual HW chunk (differs between Spectrum and Spectrum-2),
whereas vchunk struct is a SW abstraction of that. This split
prepares possibility for vchunk to hold 2 HW chunks which is needed
for region ERP rehash flow.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do the split of region struct so the new region struct is related to the
actual HW region, whereas vregion struct is a SW abstration of that.
This split prepares possibility for vregion to hold 2 HW regions which
is needed for region ERP rehash flow.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Count number of roots and add it to stats. It is handy for the library
user to have this stats available as it can act upon it without
counting roots itself.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement simple greedy algo to find more optimized root-delta tree for
a given objagg instance. This "hints" can be used by a driver to:
1) check if the hints are better (driver's choice) than the original
   objagg tree. Driver does comparison of objagg stats and hints stats.
2) use the hints to create a new objagg instance which will construct
   the root-delta tree according to the passed hints. Currently, only a
   simple greedy algorithm is implemented. Basically it finds the roots
   according to the maximal possible user count including deltas.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, user can do dump or get of param values right after the
devlink params are registered. However the driver may not be initialized
which is an issue. The same problem happens during notification
upon param registration. Allow driver to publish devlink params
whenever it is ready to handle get() ops. Note that this cannot
be resolved by init reordering, as the "driverinit" params have
to be available before the driver is initialized (it needs the param
values there).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.

Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

Notice that, in this particular case, the fall-through annotation
is placed at the beginning of the code comment, which is what
GCC is expecting to find.

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Static checker warning complains on uninitialized variable:

        drivers/net/ethernet/netronome/nfp/flower/action.c:618 nfp_fl_pedit()
        error: uninitialized symbol 'idx'.

Which is actually never used from the functions that take it as
parameter. Remove it.

Fixes: 73867881 ("drivers: net: use flow action infrastructure")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Paul Fox <pfox@solarflare.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:
 "This pull request is dedicated to the upcoming snowpocalypse parts 2
  and 3 in the Pacific Northwest:

   1) Drop profiles are broken because some drivers use dev_kfree_skb*
      instead of dev_consume_skb*, from Yang Wei.

   2) Fix IWLWIFI kconfig deps, from Luca Coelho.

   3) Fix percpu maps updating in bpftool, from Paolo Abeni.

   4) Missing station release in batman-adv, from Felix Fietkau.

   5) Fix some networking compat ioctl bugs, from Johannes Berg.

   6) ucc_geth must reset the BQL queue state when stopping the device,
      from Mathias Thore.

   7) Several XDP bug fixes in virtio_net from Toshiaki Makita.

   8) TSO packets must be sent always on queue 0 in stmmac, from Jose
      Abreu.

   9) Fix socket refcounting bug in RDS, from Eric Dumazet.

  10) Handle sparse cpu allocations in bpf selftests, from Martynas
      Pumputis.

  11) Make sure mgmt frames have enough tailroom in mac80211, from Felix
      Feitkau.

  12) Use safe list walking in sctp_sendmsg() asoc list traversal, from
      Greg Kroah-Hartman.

  13) Make DCCP's ccid_hc_[rt]x_parse_options always check for NULL
      ccid, from Eric Dumazet.

  14) Need to reload WoL password into bcmsysport device after deep
      sleeps, from Florian Fainelli.

  15) Remove filter from mask before freeing in cls_flower, from Petr
      Machata.

  16) Missing release and use after free in error paths of s390 qeth
      code, from Julian Wiedmann.

  17) Fix lockdep false positive in dsa code, from Marc Zyngier.

  18) Fix counting of ATU violations in mv88e6xxx, from Andrew Lunn.

  19) Fix EQ firmware assert in qed driver, from Manish Chopra.

  20) Don't default Caivum PTP to Y in kconfig, from Bjorn Helgaas"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
  net: dsa: b53: Fix for failure when irq is not defined in dt
  sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
  geneve: should not call rt6_lookup() when ipv6 was disabled
  net: Don't default Cavium PTP driver to 'y'
  net: broadcom: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: via-velocity: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: tehuti: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: sun: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: fsl_ucc_hdlc: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: fec_mpc52xx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: smsc: epic100: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: dscc4: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: tulip: de2104x: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: defxx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net/mlx5e: Don't overwrite pedit action when multiple pedit used
  net/mlx5e: Update hw flows when encap source mac changed
  qed*: Advance drivers version to 8.37.0.20
  qed: Change verbosity for coalescing message.
  qede: Fix system crash on configuring channels.
  qed: Consider TX tcs while deriving the max num_queues for PF.
  ...

Right now ipvlan has a hard dependency on CONFIG_NETFILTER and
otherwise it cannot be built. However, the only ipvlan operation
mode that actually depends on netfilter is l3s, everything else
is independent of it. Break this hard dependency such that users
are able to use ipvlan l3 mode on systems where netfilter is not
compiled in.

Therefore, this adds a hidden CONFIG_IPVLAN_L3S bool which is
defaulting to y when CONFIG_NETFILTER is set in order to retain
existing behavior for l3s. All l3s related code is refactored
into ipvlan_l3s.c that is compiled in when enabled.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Martynas Pumputis <m@lambda.lt>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull char/misc fixes from Greg KH:
 "Here are some small char and misc driver fixes for 5.0-rc6.

  Nothing huge here, some more binderfs fixups found as people use it,
  and there is a "large" selftest added to validate the binderfs code,
  which makes up the majority of this pull request.

  There's also some small mei and mic fixes to resolve some reported
  issues.

  All of these have been in linux-next for over a week with no reported
  issues"

* tag 'char-misc-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mic: vop: Fix crash on remove
  mic: vop: Fix use-after-free on remove
  binderfs: remove separate device_initcall()
  fpga: stratix10-soc: fix wrong of_node_put() in init function
  mic: vop: Fix broken virtqueues
  mei: free read cb on ctrl_wr list flush
  samples: mei: use /dev/mei0 instead of /dev/mei
  mei: me: add ice lake point device id.
  binderfs: respect limit on binder control creation
  binder: fix CONFIG_ANDROID_BINDER_DEVICES
  selftests: add binderfs selftests

Pull driver core fixes from Greg KH:
 "Here are some driver core fixes for 5.0-rc6.

  Well, not so much "driver core" as "debugfs". There's a lot of
  outstanding debugfs cleanup patches coming in through different
  subsystem trees, and in that process the debugfs core was found that
  it really should return errors when something bad happens, to prevent
  random files from showing up in the root of debugfs afterward. So
  debugfs was fixed up to handle this properly, and then two fixes for
  the relay and blk-mq code was needed as it was making invalid
  assumptions about debugfs return values.

  There's also a cacheinfo fix in here that resolves a tiny issue.

  All of these have been in linux-next for over a week with no reported
  problems"

* tag 'driver-core-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  blk-mq: protect debugfs_create_files() from failures
  relay: check return of create_buf_file() properly
  debugfs: debugfs_lookup() should return NULL if not found
  debugfs: return error values, not NULL
  debugfs: fix debugfs_rename parameter checking
  cacheinfo: Keep the old value if of_property_read_u32 fails

Pull staging/IIO driver fixes from Greg KH:
 "Here are some small iio and staging driver fixes for 5.0-rc6.

  Nothing big, just resolve some reported IIO driver issues, and one
  staging driver bug. One staging driver patch was added and then
  reverted as well.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Revert "staging: erofs: keep corrupted fs from crashing kernel in erofs_namei()"
  staging: erofs: keep corrupted fs from crashing kernel in erofs_namei()
  staging: octeon: fix broken phylib usage
  iio: ti-ads8688: Update buffer allocation for timestamps
  tools: iio: iio_generic_buffer: make num_loops signed
  iio: adc: axp288: Fix TS-pin handling
  iio: chemical: atlas-ph-sensor: correct IIO_TEMP values to millicelsius

Pull tty/serial fixes from Greg KH:
 "Here are some small tty and serial fixes for 5.0-rc6.

  Nothing huge, just a few small fixes for reported issues. The speakup
  fix is in here as it is a tty operation issue.

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'tty-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: fix race between flush_to_ldisc and tty_open
  staging: speakup: fix tty-operation NULL derefs
  serial: sh-sci: Do not free irqs that have already been freed
  serial: 8250_pci: Make PCI class test non fatal
  tty: serial: 8250_mtk: Fix potential NULL pointer dereference