Michael Schmitz says:

====================
New network driver for Amiga X-Surf 100 (m68k)

[This is a resend of my v3 series which was based on the wrong version and
tree. Only substantial change is to Asix AX99796B PHY driver.]

This patch series adds support for the Individual Computers X-Surf 100
network card for m68k Amiga, a network adapter based on the AX88796 chip set.

The driver was originally written for kernel version 3.19 by Michael Karcher
(see CC:), and adapted to 4.16+ for submission to netdev by me. Questions
regarding motivation for some of the changes are probably best directed at
Michael Karcher.

The driver has been tested by Adrian <glaubitz@physik.fu-berlin.de> who will
send his Tested-by tag separately.

A few changes to the ax88796 driver were required:
- to read the MAC address, some setup of the ax99796 chip must be done,
- attach to the MII bus only on device open to allow module unloading,
- allow to supersede ax_block_input/ax_block_output by card-specific
  optimized code,
- use an optional interrupt status callback to allow easier sharing of the
  card interrupt,
- set IRQF_SHARED if platform IRQ resource is marked shareable

The Asix Electronix PHY used on the X-Surf 100 is buggy, and causes the
software reset to hang if the previous command sent to the PHY was also
a soft reset. This bug requires addition of a PHY driver for Asix PHYs
to provide a fixed .soft_reset function, included in this series.

Some additional cleanup:
- do not attempt to free IRQ in ax_remove (complements 82533ad9),
- clear platform drvdata on probe fail and module remove.

Changes since v1:

Raised in review by Andrew Lunn:
- move MII code around to avoid need for forward declaration,
- combine patches 2 and 7 to add cleanup in error path

Changes since v2:

- corrected authorship attribution to Michael Karcher

Suggested by Geert Uytterhoeven:
- use ei_local->reset_8390() instead of duplicating ax_reset_8390(),
- use %pR to format struct resource pointers,
- assign pdev and xs100 pointers in declaration,
- don't split error messages,
- change Kconfig logic to only require XSURF100 set on Amiga

Suggested by Andrew Lunn:
- add COMPILE_TEST to ax88796 Kconfig options,
- use new Asix PHY driver for X-Surf 100

Suggested by Andrew Lunn/Finn Thain:
- declare struct sk_buff in ax88796.h,
- correct whitespace error in ax88796.h

Changes since v3:

- various checkpatch cleanup

Andrew Lunn:
- don't duplicate genphy_soft_reset in Asix PHY driver, just call
  genphy_soft_reset after writing zero to control register
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add platform device driver to populate the ax88796 platform data from
information provided by the XSurf100 zorro device driver. The ax88796
module will be loaded through this module's probe function.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The net device struct pointer is stored as platform device drvdata on
module probe - clear the drvdata entry on probe fail there, as well as
when unloading the module.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On the Amiga X-Surf100, the network card interrupt is shared with many
other interrupt sources, so requires the IRQF_SHARED flag to register.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To be able to tell the ax88796 driver whether it is sensible to enter
the 8390 interrupt handler, an "is this interrupt caused by the 88796"
callback has been added to the ax_plat_data structure (with NULL being
compatible to the previous behaviour).
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add platform specific hooks for block transfer reads/writes of packet
buffer data, superseding the default provided ax_block_input/output.
Currently used for m68k Amiga XSurf100.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This complements the fix in 82533ad9 ("net: ethernet: ax88796:
don't call free_irq without request_irq first") that removed the
free_irq call in the error path of probe, to also not call free_irq
when remove is called to revert the effects of probe.

Fixes: 82533ad9 (net: ethernet: ax88796: don't call free_irq without request_irq first)
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call ax_mii_init in ax_open(), and unregister/remove mdiobus resources
in ax_close().

This is needed to be able to unload the module, as the module is busy
while the MII bus is attached.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

To read the MAC address from the (virtual) SAprom, the remote DMA
unit needs to be set up like for every other process access to card-local
memory.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Asix Electronics PHY found on the X-Surf 100 Amiga Zorro network
card by Individual Computers is buggy, and needs the reset bit toggled
as workaround to make a PHY soft reset succeed.

Add workaround driver just for this special case.

Suggested in xsurf100 patch series review by Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Modernize mdio-gpio

This patchset is inspired by a previous version by Linus Walleij

It reworks the mdio-gpio code to make use of gpio descriptors instead
of gpio numbers. However compared to the previous version, it retains
support for platform devices. It does however remove the platform_data
header file. The needed GPIOs are now passed by making use of a gpiod
lookup table. e.g:

static struct gpiod_lookup_table zii_scu_mdio_gpiod_table = {
	.dev_id = "mdio-gpio.0",
	.table = {
		GPIO_LOOKUP_IDX("gpio_ich", 17, NULL, MDIO_GPIO_MDC,
				GPIO_ACTIVE_HIGH),
		GPIO_LOOKUP_IDX("gpio_ich", 2, NULL, MDIO_GPIO_MDIO,
				GPIO_ACTIVE_HIGH),
		GPIO_LOOKUP_IDX("gpio_ich", 21, NULL, MDIO_GPIO_MDO,
				GPIO_ACTIVE_LOW),
	},
};
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The platform data header file is now unused. Remove it, but add
an extra include which it brought in.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The GPIOs are described in device tree using a list, without names.
Add defines to indicate what each index in the list means. These
defines should also be used by platform devices passing GPIOs via a
GPIO lookup table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same parsing code can be used for both OF and platform devices, if
the platform device uses a gpiod_lookup_table. Parse these properties
directly into the bitbang structure, rather than use an intermediate
platform data structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moving the allocation of this structure to the probe function is a
step towards making it the core data structure of the driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This simplifies the code, removing the need to handle active low
flags, etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

No current devices use IRQs in platform data, so remove support for
it. The MDIO core will also initialise the new bus such that all
addresses are polled, so remove the unneeded re-initialisation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mdio-gpio driver was the only user of the interface reset option.
Since it no longer uses it, remove it from the bit banging code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The platform data can contain a function to call to reset
the bit banging interface. It is not used, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Seems like an old typ0.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
net/ipv6: followup to fib6_info change

Followup to fib change for IPv6.

First 2 patches rename fib6_info struct elements to match its name,
and rename addrconf_dst_alloc to match what it returns.

Patches 3-7 refactor the code to remove the need for fib6_idev reducing
fib6_info by another 8 bytes to 200 bytes.

Patch 8 fixes the gfp flags argument to addrconf_prefix_route in a
couple of places.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric noticed that __ipv6_ifa_notify is called under rcu_read_lock, so
the gfp argument to addrconf_prefix_route can not be GFP_KERNEL.

While scrubbing other calls I noticed addrconf_addr_gen has one
place with GFP_ATOMIC that can be GFP_KERNEL.

Fixes: acb54e3c ("net/ipv6: Add gfp_flags to route add functions")
Reported-by: syzbot+2add39b05179b31f912f@syzkaller.appspotmail.com
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib6_idev can be obtained from __in6_dev_get on the nexthop device
rather than caching it in the fib6_info. Remove it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After 4832c30d ("net: ipv6: put host and anycast routes on device
with address") the comparison of idev does not add value since it
correlates to the nexthop device which is already compared. Remove
the idev comparison.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to 4832c30d ("net: ipv6: put host and anycast routes on device
with address") host routes and anycast routes were installed with the
device set to loopback (or VRF device once that feature was added). In the
older code dst.dev was set to loopback (needed for packet tx) and rt6i_idev
was used to denote the actual interface.

Commit 4832c30d changed the code to have dst.dev pointing to the real
device with the switch to lo or vrf device done on dst clones. As a
consequence of this change ip6_route_get_saddr can just pass the nexthop
device to ipv6_dev_get_saddr.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to 4832c30d ("net: ipv6: put host and anycast routes on device
with address") host routes and anycast routes were installed with the
device set to loopback (or VRF device once that feature was added). In the
older code dst.dev was set to loopback (needed for packet tx) and rt6i_idev
was used to denote the actual interface.

Commit 4832c30d changed the code to have dst.dev pointing to the real
device with the switch to lo or vrf device done on dst clones. As a
consequence of this change a couple of device checks during route lookups
are no longer needed. Remove them.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

aca_idev has only 1 user - inet6_fill_ifacaddr - and it only
wants the device index which can be extracted from the fib6_info
nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

addrconf_dst_alloc now returns a fib6_info. Update the name
and its users to reflect the change.

Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the prefix for fib6_info struct elements from rt6i_ to fib6_.
rt6i_pcpu and rt6i_exception_bucket are left as is given that they
point to rt6_info entries.

Rename only; not functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After working on IP defragmentation lately, I found that some large
packets defeat CHECKSUM_COMPLETE optimization because of NIC adding
zero paddings on the last (small) fragment.

While removing the padding with pskb_trim_rcsum(), we set skb->ip_summed
to CHECKSUM_NONE, forcing a full csum validation, even if all prior
fragments had CHECKSUM_COMPLETE set.

We can instead compute the checksum of the part we are trimming,
usually smaller than the part we keep.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables arm64 platform support for the HINIC driver.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
tracking TCP data delivery and ECN stats

This patch series improve tracking the data delivery status
  1. minor improvement on SYN data
  2. accounting bytes delivered with CE marks
  3. exporting the delivery stats to applications

s.t. users can get better sense of TCP performance at per host,
per connection, and even per application message level.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Export data delivered and delivered with CE marks to
1) SNMP TCPDelivered and TCPDeliveredCE
2) getsockopt(TCP_INFO)
3) Timestamping API SOF_TIMESTAMPING_OPT_STATS

Note that for SCM_TSTAMP_ACK, the delivery info in
SOF_TIMESTAMPING_OPT_STATS is reported before the info
was fully updated on the ACK.

These stats help application monitor TCP delivery and ECN status
on per host, per connection, even per message level.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a new delivered_ce stat in tcp socket to estimate
number of packets being marked with CE bits. The estimation is
done via ACKs with ECE bit. Depending on the actual receiver
behavior, the estimation could have biases.

Since the TCP sender can't really see the CE bit in the data path,
so the sender is technically counting packets marked delivered with
the "ECE / ECN-Echo" flag set.

With RFC3168 ECN, because the ECE bit is sticky, this count can
drastically overestimate the nummber of CE-marked data packets

With DCTCP-style ECN this should be reasonably precise unless there
is loss in the ACK path, in which case it's not precise.

With AccECN proposal this can be made still more precise, even in
the case some degree of ACK loss.

However this is sender's best estimate of CE information.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new helper tcp_newly_delivered() to prepare the ECN accounting change.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

the tcp_sock:delivered has inconsistent accounting for SYN and FIN.
1. it counts pure FIN
2. it counts pure SYN
3. it counts SYN-data twice
4. it does not count SYN-ACK

For congestion control perspective it does not matter much as C.C. only
cares about the difference not the aboslute value. But the next patch
would export this field to user-space so it's better to report the absolute
value w/o these caveats.

This patch counts SYN, SYN-ACK, or SYN-data delivery once always in
the "delivered" field.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lockdep does not know that the locks used by IPv4 defrag
and IPv6 reassembly units are of different classes.

It complains because of following chains :

1) sch_direct_xmit()        (lock txq->_xmit_lock)
    dev_hard_start_xmit()
     xmit_one()
      dev_queue_xmit_nit()
       packet_rcv_fanout()
        ip_check_defrag()
         ip_defrag()
          spin_lock()     (lock frag queue spinlock)

2) ip6_input_finish()
    ipv6_frag_rcv()       (lock frag queue spinlock)
     ip6_frag_queue()
      icmpv6_param_prob() (lock txq->_xmit_lock at some point)

We could add lockdep annotations, but we also can make sure IPv6
calls icmpv6_param_prob() only after the release of the frag queue spinlock,
since this naturally makes frag queue spinlock a leaf in lock hierarchy.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the NetVSP v6 and 6.1 message structures, and includes
these versions into NetVSC/NetVSP version negotiation process.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>