Skip to content

L
linux
Switch branch/tag
  1. 08 Jan, 2017 6 commits
    • Grygorii Strashko's avatar
      net: ethernet: ti: cpsw: add support for ringparam configuration · be034fc1
      Grygorii Strashko authored 
      The CPDMA uses one pool of descriptors for both RX and TX which by default
split between all channels proportionally depending on total number of
CPDMA channels and number of TX and RX channels. As result, more
descriptors will be consumed by TX path if there are more TX channels and
there is no way now to dedicate more descriptors for RX path.

So, add the ability to re-split CPDMA pool of descriptors between RX and TX
path via ethtool '-G' command wich will allow to configure and fix number
of descriptors used by RX and TX path, which, then, will be split between
RX/TX channels proportionally depending on RX/TX channels number and
weight. ethtool '-G' command will accept only number of RX entries and rest
of descriptors will be arranged for TX automatically.

Command:
  ethtool -G <devname> rx <number of descriptors>

defaults and limitations:
- minimum number of rx descriptors is 10% of total number of descriptors in
  CPDMA pool
- maximum number of rx descriptors is 90% of total number of descriptors in
  CPDMA pool
- by default, descriptors will be split equally between RX/TX path
- any values passed in "tx" parameter will be ignored

Usage:

 # ethtool -g eth0
	Pre-set maximums:
	RX:             7372
	RX Mini:        0
	RX Jumbo:       0
	TX:             0
	Current hardware settings:
	RX:             4096
	RX Mini:        0
	RX Jumbo:       0
	TX:             4096

 # ethtool -G eth0 rx 7372
 # ethtool -g eth0
	Ring parameters for eth0:
	Pre-set maximums:
	RX:             7372
	RX Mini:        0
	RX Jumbo:       0
	TX:             0
	Current hardware settings:
	RX:             7372
	RX Mini:        0
	RX Jumbo:       0
	TX:             820
Signed-off-by: default avatarGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      be034fc1
    • Grygorii Strashko's avatar
      net: ethernet: ti: cpsw: add support for descs pool size configuration · 90225bf0
      Grygorii Strashko authored 
      The CPSW CPDMA can process buffer descriptors placed as in internal
CPPI RAM as in DDR. This patch adds support in CPSW and CPDMA for
descs_pool_size mudule parameter, which defines total number of CPDMA CPPI
descriptors to be used for both ingress/egress packets processing:
 - memory size, required for CPDMA descriptor pool, is calculated basing
on number of descriptors specified by user in descs_pool_size and
CPDMA descriptor size and allocated from coherent memory (CMA area);
 - CPDMA descriptor pool will be allocated in DDR if pool memory size >
internal CPPI RAM or use internal CPPI RAM otherwise;
 - if descs_pool_size not specified in DT - the default value 256 will
be used which will allow to place CPDMA descriptors pool into the
internal CPPI RAM (current default behaviour);
 - CPDMA will ignore descs_pool_size if descs_pool_size = 0 for
backward comaptiobility with davinci_emac.

descs_pool_size is boot time setting and can't be changed once
CPSW/CPDMA is initialized.
Signed-off-by: default avatarGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      90225bf0
    • Grygorii Strashko's avatar
      net: ethernet: ti: cpdma: use devm_ioremap · 7f3b490a
      Grygorii Strashko authored 
      Use devm_ioremap() and simplify the code.
Signed-off-by: default avatarGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      7f3b490a
    • Grygorii Strashko's avatar
      net: ethernet: ti: cpdma: minimize number of parameters in cpdma_desc_pool_create/destroy() · 5fcc40a9
      Grygorii Strashko authored 
      Update cpdma_desc_pool_create/destroy() to accept only one parameter
struct cpdma_ctlr*, as this structure contains all required
information for pool creation/destruction.
Signed-off-by: default avatarGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      5fcc40a9
    • Grygorii Strashko's avatar
      net: ethernet: ti: cpdma: fix desc re-queuing · 12a303e3
      Grygorii Strashko authored 
      The currently processing cpdma descriptor with EOQ flag set may
contain two values in Next Descriptor Pointer field:
- valid pointer: means CPDMA missed addition of new desc in queue;
- null: no more descriptors in queue.
In the later case, it's not required to write to HDP register, but now
CPDMA does it.

Hence, add additional check for Next Descriptor Pointer != null in
cpdma_chan_process() function before writing in HDP register.
Signed-off-by: default avatarGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      12a303e3
    • Grygorii Strashko's avatar
      net: ethernet: ti: cpdma: am437x: allow descs to be plased in ddr · a6c83ccf
      Grygorii Strashko authored 
      It's observed that cpsw/cpdma is not working properly when CPPI
descriptors are placed in DDR instead of internal CPPI RAM on am437x
SoC:
- rx/tx silently stops processing packets;
- or - after boot it's working for sometime, but stuck once Network
load is increased (ping is working, but iperf is not).
(The same issue has not been reproduced on am335x and am57xx).

It seems that write to HDP register processed faster by interconnect
than writing of descriptor memory buffer in DDR, which is probably
caused by store buffer / write buffer differences as these functions
are implemented differently across devices. So, to fix this i come up
with two minimal, required changes:

1) all accesses to the channel register HDP/CP/RXFREE registers should
be done using sync IO accessors readl()/writel(), because all previous
memory writes writes have to be completed before starting channel
(write to HDP) or completing desc processing.

2) the change 1 only doesn't work on am437x and additional reading of
desc's field is required right after the new descriptor was filled
with data and before pointer on it will be stored in
prev_desc->hw_next field or HDP register.

In addition, to above changes this patch eliminates all relaxed ordering
I/O accessors in this driver as suggested by David Miller to avoid such
kind of issues in the future, but with one exception - relaxed IO accessors
will still be used to fill desc in cpdma_chan_submit(), which is safe as
there is read barrier at the end of write sequence, and because sync IO
accessors usage here will affect on net performance.
Signed-off-by: default avatarGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a6c83ccf
  3. 07 Jan, 2017 9 commits
  5. 06 Jan, 2017 23 commits
  7. 05 Jan, 2017 2 commits
    • Sowmini Varadhan's avatar
      tools: psock_tpacket: block Rx until socket filter has been added and socket... · c1878f7a
      Sowmini Varadhan authored 
      tools: psock_tpacket: block Rx until socket filter has been added and socket has been bound to loopback.

Packets from any/all interfaces may be queued up on the PF_PACKET socket
before it is bound to the loopback interface by psock_tpacket, and
when these are passed up by the kernel, they could interfere
with the Rx tests.

Avoid interference from spurious packet by blocking Rx until the
socket filter has been set up, and the packet has been bound to the
desired (lo) interface. The effective sequence is
	socket(PF_PACKET, SOCK_RAW, 0);
	set up ring
	Invoke SO_ATTACH_FILTER
	bind to sll_protocol set to ETH_P_ALL, sll_ifindex for lo
After this sequence, the only packets that will be passed up are
those received on loopback that pass the attached filter.
Signed-off-by: default avatarSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      c1878f7a
    • Soheil Hassas Yeganeh's avatar
      tcp: provide timestamps for partial writes · ad02c4f5
      Soheil Hassas Yeganeh authored 
      For TCP sockets, TX timestamps are only captured when the user data
is successfully and fully written to the socket. In many cases,
however, TCP writes can be partial for which no timestamp is
collected.

Collect timestamps whenever any user data is (fully or partially)
copied into the socket. Pass tcp_write_queue_tail to tcp_tx_timestamp
instead of the local skb pointer since it can be set to NULL on
the error path.

Note that tcp_write_queue_tail can be NULL, even if bytes have been
copied to the socket. This is because acknowledgements are being
processed in tcp_sendmsg(), and by the time tcp_tx_timestamp is
called tcp_write_queue_tail can be NULL. For such cases, this patch
does not collect any timestamps (i.e., it is best-effort).

This patch is written with suggestions from Willem de Bruijn and
Eric Dumazet.

Change-log V1 -> V2:
	- Use sockc.tsflags instead of sk->sk_tsflags.
	- Use the same code path for normal writes and errors.
Signed-off-by: default avatarSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: default avatarYuchung Cheng <ycheng@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: default avatarWillem de Bruijn <willemb@google.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ad02c4f5
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7