XB113 (AR9380) 3x3 SB 5G only cards were failing to connect to APs
due to incorrect xpabiaslevel configuration. fix it.

Cc: stable@kernel.org
Cc: Ray Li <ray.li@greenwavereality.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: compat@orbit-lab.org
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The function
- increments dropped rx_packet count if status code
  passed to it is "-1".
- frees SKB buffer.

But currently the function is being called with "0" status code.
This patch replaces above function by dev_kfree_skb_any() call.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The XB113 cards are single band, 5 GHz-only, but the
default settings were configured to assume it was dual
band. Users of these cards then would see 2.4 GHz channels
but you would never get any scan results from these channels
given that the radio is not present.

Cc: stable@kernel.org
Cc: Fiona Cain <Fiona.Cain@atheros.com>
Cc: Ray Li <ray.li@greenwavereality.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Dan Friedman <dan.friedman@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When transmitting a frame, the transmitter waits a random number of
slots between 0 and cw. Thus, the contention time is (cw / 2) * t_slot
which we can represent instead as (cw * t_slot) >> 1. Also fix a few
other accounting bugs around contention time, and add comments.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Multiple virtual AP interfaces can currently try
to use different beacon intervals, but that just
leads to problems since it won't actually be done
that way by drivers. Return an error in this case
to make sure it won't be done wrong.

Also, ignore attempts to change the DTIM period
or beacon interval during the lifetime of the BSS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/mac80211/cfg.c: In function ‘sta_apply_parameters’:
net/mac80211/cfg.c:746: error: ‘struct sta_info’ has no member named ‘plink_state’
make[1]: *** [net/mac80211/cfg.o] Error 1
make: *** [net/mac80211/mac80211.ko] Error 2
Signed-off-by: John W. Linville <linville@tuxdriver.com>

They were added by me while testing and I forgot to remove.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

If we can't find a ACL link between the devices, we search
the connection list one second time looking for LE links.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

We need to be able for receive events notifying that the connection
was established, the connection attempt failed or that disconnection
happened.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Introduce NL80211_ATTR_SCHED_SCAN_INTERVAL as a required attribute for
NL80211_CMD_START_SCHED_SCAN.  This value informs the driver at which
intervals the scheduled scan cycles should be executed.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Implement support for HW scheduled scan.  The mac80211 code doesn't perform
scheduled scans itself, but calls the driver to start and stop scheduled
scans.

This patch also creates a trace event class to be used by drv_hw_scan
and the new drv_sched_scan_start and drv_sched_stop functions, in
order to avoid duplicate code.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Implement new functionality for scheduled scan offload.  With this feature we
can scan automatically at certain intervals.

The idea is that the hardware can perform scan automatically and filter on
desired results without waking up the host unnecessarily.

Add NL80211_CMD_START_SCHED_SCAN and NL80211_CMD_STOP_SCHED_SCAN
commands to the nl80211 interface.  When results are available they are
reported by NL80211_CMD_SCHED_SCAN_RESULTS events.  The userspace is
informed when the scheduled scan has stopped with a
NL80211_CMD_SCHED_SCAN_STOPPED event, which can be triggered either by
the driver or by a call to NL80211_CMD_STOP_SCHED_SCAN.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This allows individual users and deployments to disable mesh support at
runtime, i.e. without having to build and maintain a custom kernel.

Based on a patch by Paul Fox <pgf@laptop.org>.
Signed-off-by: Sascha Silbe <silbe@activitycentral.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some structures and macros in ioctl.h are redundant or no longer
used.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Avoid use of local structure in the function if the structure is
already allocated by the caller and the structure pointer is passed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Documented in: <4DCA7E40.9070709@lwfinger.net>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commiting settings is possible on devices without PCI core (but with CC
core). Export it for usage in drivers supporting other cores.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Similar patch was commited to ssb.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Only leave filtering enabled for AP or VLAN interfaces, clear the
destination mask for all other interfaces.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is not N-PHY specific function, we partially duplicate code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The functions drv_add_interface() and drv_remove_interface() print out
the same values in the traces.  Combine the traces of these two
functions into one event class to remove some duplicate code.

Also add a new class for functions drv_set_frag_threshold() and
drv_set_rts_threshold().

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This was introduced in 2.6.39-rc1 it seems.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes routing loops in PREP propagation and is in accordance with Draft
11, Section: 11C.9.8.4.
Signed-off-by: Fabrice Deyber <fabricedeyber@agilemesh.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Mesh beaconing on ath9k was broken by this commit:

commit 4801416c
Author: Ben Greear <greearb@candelatech.com>
Date:   Sat Jan 15 19:13:48 2011 +0000

This patch assigns the right opmode when the device is used in mesh
mode.

Reported-by: Fabrice Deyber fabricedeyber@agilemesh.com
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is necessary for userspace managed stations.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

PROVE_RCU caught that one:

[  431.214070] ===================================================
[  431.215341] [ INFO: suspicious rcu_dereference_check() usage. ]
[  431.215674] ---------------------------------------------------
[  431.216043] net/mac80211/mesh_pathtbl.c:184 invoked
rcu_dereference_check() without protection!
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The mesh and mpp path tables are accessed from softirq and workqueue
context so non-irq locking cannot be used.  Or at least that's what
PROVE_RCU seems to tell us here:

[  431.240946] =================================
[  431.241061] [ INFO: inconsistent lock state ]
[  431.241061] 2.6.39-rc3-wl+ #354
[  431.241061] ---------------------------------
[  431.241061] inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
[  431.241061] kworker/u:1/1423 [HC0[0]:SC0[0]:HE1:SE1] takes:
[  431.241061]  (&(&newtbl->hashwlock[i])->rlock){+.?...}, at:
[<c14671bf>] mesh_path_add+0x167/0x257
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Not sure if I'm chasing a ghost here, seems like the
mesh_path->size_order needs to be inside an RCU-read section to prevent
that value from changing between table allocation and copying.  We have
observed crashes that might be caused by this.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

They may contain encrypted information elements (as AMPE frames do)
but they are not encrypted.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Mesh beacons no longer use all-zeroes BSSID.  Beacon frames for MBSS,
infrastructure BSS, or IBSS are differentiated by the Capability
Information field in the Beacon frame.  A mesh STA sets the ESS and IBSS
subfields to 0 in transmitted Beacon or Probe Response management
frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Previous versions of 11s draft used the all zeroes address.  Current
draft uses the same address as address 2.

Also, use the ANA-approved action category code for peer establishment frames.

Note: This breaks compatibility with previous mesh protocol instances.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Note: This breaks compatibility with previous mesh protocol instances.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Introduce a new configuration option to support AMPE from userspace.

Prior to this series we only supported authentication in userspace: an
authentication daemon would authenticate peer candidates in userspace
and hand them over to the kernel.  From that point the mesh stack would
take over and establish a peer link (Mesh Peering Management).

These patches introduce support for Authenticated Mesh Peering Exchange
in userspace.  The userspace daemon implements the AMPE protocol and on
successfull completion create mesh peers and install encryption keys.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>