NFC_CMD_ACTIVATE_TARGET and NFC_ATTR_SE_PARAMS comments are missing.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Potentially an unexpected HCI event may occur because of a
firmware bug. It could be transparent for the user but we need to
at least log it.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add support for proprietary commands useful mainly for
factory testings. Here is a list:

- FACTORY_MODE: Allow to set the driver into a mode where
  no secure element are activated. It does not consider any
  NFC_ATTR_VENDOR_DATA.
- HCI_CLEAR_ALL_PIPES: Allow to execute a HCI clear all pipes
  command. It does not consider any NFC_ATTR_VENDOR_DATA.
- HCI_DM_PUT_DATA: Allow to configure specific CLF registry
  like for example RF trimmings or low level drivers
  configurations (I2C, SPI, SWP).
- HCI_DM_UPDATE_AID: Allow to configure an AID routing into the
  CLF routing table following RF technology, CLF mode or protocol.
- HCI_DM_GET_INFO: Allow to retrieve CLF information.
- HCI_DM_GET_DATA: Allow to retrieve CLF configurable data such as
  low level drivers configurations or RF trimmings.
- HCI_DM_DIRECT_LOAD: Allow to load a firmware into the CLF.
  A complete packet can be more than 8KB.
- HCI_DM_RESET: Allow to run a CLF reset in order to "commit" CLF
  configuration changes without CLF power off.
- HCI_GET_PARAM: Allow to retrieve an HCI CLF parameter (for example
  the white list).
- HCI_DM_FIELD_GENERATOR: Allow to generate different kind of RF
  technology. When using this command to anti-collision is done.
- HCI_LOOPBACK: Allow to echo a command and test the Dh to CLF
  connectivity.
- HCI_DM_VDC_MEASUREMENT_VALUE: Allow to measure the field applied
  on the CLF antenna. A value between 0 and 0x0f is returned. 0 is
  maximum.
- HCI_DM_FWUPD_START: Allow to put CLF into firmware update mode.
  It is a specific CLF command as there is no GPIO for this.
- HCI_DM_FWUPD_END:  Allow to complete firmware update.
- HCI_DM_VDC_VALUE_COMPARISON: Allow to compare the field applied
  on the CLF antenna to a reference value.
- MANUFACTURER_SPECIFIC: Allow to retrieve manufacturer specific data
  received during a NCI_CORE_INIT_CMD.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

It is useless to start from index 0 when looking for a gate
because only dynamic pipes are retrieved with
ST21NFCA_DM_GETINFO(ST21NFCA_DM_GETINFO_PIPE_LIST).

The first dynamic pipe is present at index 3.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

It is useless to start from index 0 when looking for a gate
because only dynamic pipes are retrieved with
ST_NCI_DM_GETINFO(ST_NCI_DM_GETINFO_PIPE_LIST).

The first dynamic pipe is present at index 3.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NCI_HCI_IDENTITY_MGMT_GATE might be useful to get information
about hardware or firmware version.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When initializing ndev->hci_dev->init_data, only gates field
was set. gate_count needs to be initialized as well.

Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

We need to keep initial st_nci_gates values in order for
nfc_hci_dev_connect_gates to create and open pipe when necessary.

For example after a firmware update CLF pipes are cleared. Changing
pipe values in st21nfca_gates was causing nfc_hci_dev_connect_gates
not using accurate pipes value.

Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

We need to keep initial st_nci_gates values in order for
nci_hci_dev_connect_gates to create and open pipe when necessary.

For example after a firmware update CLF pipes are cleared. Changing
pipe values in st_nci_gates was causing nci_hci_dev_connect_gates
not using accurate pipes value.

Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC_HCI_LINK_MGMT_PIPE was never opened in nfc_hci_load_session.

Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NCI_HCI_LINK_MGMT_PIPE was never opened in st_nci_hci_load_session.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

hdev->init_data.gates is already initialized in st21nfca_hci_probe.

Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

ndev->hci_dev->init_data.gates is already initialized in
st_nci_hci_network.

Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Some gates might need to have their pipes explicitly created.
Add a call to nci_hci_create_pipe in nci_hci_connect_gate for
every gate that is different than NCI_HCI_LINK_MGMT_GATE or
NCI_HCI_ADMIN_GATE.

In case of an error when opening a pipe, like in hci layer,
delete the pipe if it was created.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When session_id is filled to 0xff, the pipe configuration is
probably incorrect and needs to be cleared.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

nci_hci_clear_all_pipes might be use full in some cases
for example after a firmware update.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When receiving data in nci_hci_msg_rx_work, extract pipe
value using NCI_HCP_MSG_GET_PIPE macro.

Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When sending HCI data over NCI, HCI return code is part
of the NCI data. In order to get correctly the HCI return
code, we assume the NCI communication is successful and
extract the return code for the nci_hci functions return code.

This is done because nci_to_errno does not match hci return
code value.

Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When sending HCI data over NCI, cmd information should be
present only on the first packet.
Each packet shall be specifically allocated and sent to the
NCI layer.

Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When sending data over SPI, the maximum expected length is the maximum
nci packet payload + data header size + the frame head room (1 for the
ndlc header) + the frame trail room (0).

Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Align st21nfca driver with or nfc driver:
- Remove st21nfca_ prefix
- Merge st21nfca_se.h, st21nfca_dep.h in st21nfca.h
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

st-nci.h already include ndlc.h.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Align st-nci driver with other NFC drivers:
- Remove st-nci_ prefix
- Merge se.h in st-nci.h
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Fields Peak complies with the ISO/IEC 14443A/B, 15693, 18092,
and JIS X 6319-4. It is an NCI based controller.

RF Protocols supported:
 - NFC Forum Type 1 Tags (Jewel, Topaz)
 - NFC Forum Type 2 Tags (Mifare UL)
 - NFC Forum Type 3 Tags (FeliCa)
 - NFC Forum Type 4A (ISO/IEC 14443 A-4 106kbps to 848kbps)
 - NFC Forum Type 4B (ISO/IEC 14443 B-4 106kbps to 848kbps)
 - NFCIP in passive and active modes (ISO/IEC 18092 106kbps
   to 424kbps)
 - B’ (based on ISO/IEC 14443 B-2)
 - iCLASS (based on ISO/IEC 15693-2)
 - Vicinity cards (ISO/IEC 15693-3)
 - Kovio tags (NFC Forum Type 2)

The device can be enumerated using ACPI using the id INT339A.
The 1st GPIO is the IRQ and the 2nd is the RESET pin.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This functin takes as a parameter a pointer to the nci_dev
struct and the first byte from the values of the first domain
specific parameter that was used for the connection creation.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If the number of destination speific parameters supplied is 0
the call will fail. If the first destination specific parameter
does not have a value, curr_id will be set to 0.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Initially it was used to create hooks in the driver for
proprietary operations. Currently it is being used for hooks
for both proprietary and generic operations.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The driver may be required to act when some responses or
notifications arrive. For example the NCI core does not have a
handler for NCI_OP_CORE_GET_CONFIG_RSP. The NFCC can send a
config response that has to be read by the driver and the packet
may contain vendor specific data.

The Fields Peak driver needs to take certain actions when a reset
notification arrives (packet also not handled by the nfc core).

The driver handlers do not interfere with the core and they are
called after the core processes the packet.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This allows sending core commands from the driver. The driver
should be able to send NCI core commands like CORE_GET_CONFIG_CMD.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The driver should know that it can continue with post setup where
setup left off. Being able to execute post_setup when setup fails
may force the developer to keep this state in the driver.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add NCI_OP_CORE_GET_CONFIG_CMD, NCI_OP_CORE_GET_CONFIG_RSP
and NCI_OP_CORE_RESET_NTF.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

FDP driver needs to send the firmware as regular packets
(not fragmented). The driver should have a way to
get the max packet size for a given connection.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

For the firmware update the driver may use nci_send_data.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Rename it to se.c to keep the driver files namespace consistent.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The exit label performs device_unlock(&dev->dev);, which will fail when dev
is NULL, and nfc_put_device(dev);, which is not useful when dev is NULL, so
just exit the function immediately.

Problem found using scripts/coccinelle/null/deref_null.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

There is no need to have the 'struct nfcwilink *drv' variable static in the
probe function.
It only wastes a few bytes of memory.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The only instance of a nxp_nci_phy_ops structure is never modified.  Thus
the declaration of the structure and all references to the structure type
can be made const.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

As I understand it, the core nfcmrvl module is useless without
either the USB or the UART access module. So hide NFC_MRVL and select
it automatically if either NFC_MRVL_USB or NFC_MRVL_UART is selected.

This avoids presenting NFC_MRVL when neither NFC_MRVL_USB nor
NFC_MRVL_UART can be selected.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

As I understand it, the core nfc_microread module is useless without
either the I2C or the MEI access module. So hide NFC_MICROREAD and
select it automatically if either NFC_MICROREAD_I2C or
NFC_MICROREAD_MEI is selected.

This avoids presenting NFC_MICROREAD when neither NFC_MICROREAD_I2C
nor NFC_MICROREAD_MEI can be selected.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

As I understand it, the core nfc_pn544 module is useless without
either the I2C or the MEI access module. So hide NFC_PN544 and
select it automatically if either NFC_PN544_I2C or NFC_PN544_MEI is
selected.

This avoids presenting NFC_PN544 when neither NFC_PN544_I2C nor
NFC_PN544_MEI can be selected.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>