USB1 VBUS is directly tied to the 5V rail on the board. It is not
individually controllable. Drop the regulator.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

On the Lamobo R1, USB2 is connected to the RTL8192CU WiFi module.
The power enable pin is connected to PH12.

Fix the enable pin the reg_usb2_vbus.

Also disable ohci1, as the WiFi module is USB 2.0 capable.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The auxtek t004 has its otg usb vbus hardwired to 5v (likely in case
people use it to power the board instead of the dedicated power micro
usb connector), it does have an id pin, so it allows full otg
functionality.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

In order to be able to properly generate its pixel clock, the pll3-2x fixed
factor needs to be able to change the PLL3 rate too.

Add the needed extra compatible so that it behaves that way.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the new DAI blocks to the device tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This commit adds all the mod1 clocks available on A20 to its device
tree. This list was created by looking at the A20 user manual.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The a10s mk802 uses a rtl8189es sdio wifi chip, add a node enabling
the mmc1 controller, this enables using the wifi chip (together with
an out of tree sdio driver for it).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the axp152 pmic to the mk802 dts, note there are
no regulator nodes as we do not yet support the regulators on the
axp152.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the otg controller, the id pin is not connected so enable
it in peripheral only mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Now that we have a proper binding for Ethernet switches hanging off
different buses, and a driver for the BCM53125 switch, add its Device
Tree as a child MDIO node, at MDIO address 30 (Broadcom pseudo-PHY
address) and describe the ports layout of the Lamobo R1 board.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The early A13 Q8 tablets all use a Realtek WiFi module connected to
USB1. The module is powered by AXP209's LDO3 at 3.3V.

Move the related settings from sun5i-a13-q8-tablet.dts to
sun5i-q8-common.dtsi, for all q8-based tablets.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add support for the Bananapi M1 Plus A20 development board from
sinovoip.com.cn . This board is nearly a clone of the Lemaker's
Bananapro, but differ with the wlan chipset connection and i2s pinout.
And I also enable the integrated audio codec on default.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some of the sun8i q8 boards have an usb wifi controller, on other
variants this will result in an used usb root-hub, but the best
way to deal with wifi on this boards is to simply let the kernel
auto-detect usb or sdio wifi controllers.

This has been tested on an a23 based q8 tablet with a RTL8188ETV wifi
controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Move the mmc nodes above the ohci nodes for proper ordering by name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Move the &pio node below the mmc nodes for proper ordering by name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add NAND Flash controller node definition to the A20 SoC.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add NAND Flash controller node definition to the A10 SoC.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add pmic / regulator nodes to Mele M9 dts.

Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add pmic / regulator nodes to Mele A1000G quad dts.

Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The blue led on the Mele M9 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".

Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.

This renames the led from m9:blue:usr to m9:blue:pwr and marks
it as default on, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The blue led on the Mele A1000 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".

Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.

This renames the led from m9:blue:usr to a1000g:blue:pwr (fixing a copy
and paste error in the prefix while at it) and marks it as default on,
fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The blue led on the Mele A1000 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".

Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.

This renames the led from a1000:blue:usr to a1000:blue:pwr and marks
it as default on, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The Polaroid mid2809pxe04 tablet uses an sdio esp8089 wifi chip, so
ehci0 is not used and should be disabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Now that we've all the necessary bits in place we can enable
full otg support on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Now that we've all the necessary bits in place we can enable
full otg support on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the drivebus regulator which is an (optional)
part of the axp221/axp223 pmic. Since this regulator may not be
available at all depending on the board, mark it as disabled by
default.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the (optional) usbpower-supply of the
axp221 / axp223 pmic.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Use of these as regulators conflicts with use of the gpio pins as
gpios, so disabled the ldo_io# regulators by default, this avoids
the regulator core touching them when the pins are used as gpios.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

No functional change. Re-order sun7i pinctrl nodes alphabetically.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

No functional change. Re-order sun4i pinctrl nodes alphabetically.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Update the simplefb nodes for hdmi / tv-encoder out to point to
tcon0_ch1 instead of tcon0_ch0 as tcon clock.

While at it fix the clocks lines being longer than 80 chars.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Update the simplefb nodes for hdmi / tv-encoder out to point to
tcon0_ch1 instead of tcon0_ch0 as tcon clock.

While at it fix the clocks lines being longer than 80 chars.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

It seems that recent kernels have a shorter timeout when scanning for
ethernet phys causing us to hit a timeout on boards where the phy's
regulator gets enabled just before scanning, which leads to non working
ethernet.

A 10ms startup delay seems to be enough to fix it, this commit adds a
20ms startup delay just to be safe.

This has been tested on a sun4i-a10-a1000 and sun5i-a10s-wobo-i5 board,
both of which have non-working ethernet on recent kernels without this
fix.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

sunxi-common-regulators.dtsi provided dummy regulators vcc3v0, vcc3v3,
vcc5v0. 3.0V/3.3V and 5.0V are commonly used voltages in Allwinner
devices. These dummy regulators provide a stand-in when bindings that
require one, but the real regulator is not supported yet.

Since these are no longer needed, we can drop the include file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

sunxi-common-regulators.dtsi provided dummy regulators vcc3v0, vcc3v3,
vcc5v0. 3.0V/3.3V and 5.0V are commonly used voltages in Allwinner
devices. These dummy regulators provide a stand-in when bindings that
require one, but the real regulator is not supported yet.

Since these are no longer needed, we can drop the include file by
copying over reg_usb1_vbus.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

It seems that the wifi chip is powered by both ldo3 and ldo4 tied
together and that using only one results in the wifi-chip dropping of
the USB bus sometimes.

Ideally we would have a proper way of modelling this (this is being
worked on), but currently we do not. This is not an issue since we need
to keep these regulators always-on anyways, due to these boards
crashing when ldo3/4 get turned back on after having been turned off.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The BPI-M2+ is an H3 development board. It is a smaller form factor than
the original BPI-M2, with the new H3 SoC.

It has 1GB DRAM, 8GB eMMC, a micro SD card slot, HDMI output, 2 USB
host connector and 1 USB OTG connector, an IR receiver, WiFi+BT based
on Ampak AP6212.

The board also has a 3 pin header for (debug) UART, a 40 pin GPIO header
based on the Raspberry Pi B+, but the peripheral signals are not the
same, and an FPC connector for connecting BPI's camera.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add uart1 pins for 4 pin (RX/TX/RTS/CTS) mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Move uart0 pins to sort the list of pin settings in alphabetical order.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>