Rearrange 64K PTE bits to free up bits 3, 4, 5 and 6
in the 64K backed HPTE pages. This along with the earlier
patch will entirely free up the four bits from 64K PTE.
The bit numbers are big-endian as defined in the ISA3.0

This patch does the following change to 64K PTE backed
by 64K HPTE.

H_PAGE_F_SECOND (S) which occupied bit 4 moves to the
	second part of the pte to bit 60.
H_PAGE_F_GIX (G,I,X) which occupied bit 5, 6 and 7 also
	moves to the second part of the pte to bit 61,
 	62, 63, 64 respectively

since bit 7 is now freed up, we move H_PAGE_BUSY (B) from
bit 9 to bit 7.

The second part of the PTE will hold
(H_PAGE_F_SECOND|H_PAGE_F_GIX) at bit 60,61,62,63.
NOTE: None of the bits in the secondary PTE were not used
by 64k-HPTE backed PTE.

Before the patch, the 64K HPTE backed 64k PTE format was
as follows

 0 1 2 3 4  5  6  7  8 9 10...........................63
 : : : : :  :  :  :  : : :                            :
 v v v v v  v  v  v  v v v                            v

,-,-,-,-,--,--,--,--,-,-,-,-,-,------------------,-,-,-,
|x|x|x| |S |G |I |X |x|B| |x|x|................|x|x|x|x| <- primary pte
'_'_'_'_'__'__'__'__'_'_'_'_'_'________________'_'_'_'_'
| | | | |  |  |  |  | | | | |..................| | | | | <- secondary pte
'_'_'_'_'__'__'__'__'_'_'_'_'__________________'_'_'_'_'

After the patch, the 64k HPTE backed 64k PTE format is
as follows

 0 1 2 3 4  5  6  7  8 9 10...........................63
 : : : : :  :  :  :  : : :                            :
 v v v v v  v  v  v  v v v                            v

,-,-,-,-,--,--,--,--,-,-,-,-,-,------------------,-,-,-,
|x|x|x| |  |  |  |B |x| | |x|x|................|.|.|.|.| <- primary pte
'_'_'_'_'__'__'__'__'_'_'_'_'_'________________'_'_'_'_'
| | | | |  |  |  |  | | | | |..................|S|G|I|X| <- secondary pte
'_'_'_'_'__'__'__'__'_'_'_'_'__________________'_'_'_'_'

The above PTE changes is applicable to hugetlbpages aswell.

The patch does the following code changes:

a) moves the H_PAGE_F_SECOND and H_PAGE_F_GIX to 4k PTE
	header since it is no more needed b the 64k PTEs.
b) abstracts out __real_pte() and __rpte_to_hidx() so the
	caller need not know the bit location of the slot.
c) moves the slot bits to the secondary pte.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Rearrange 64K PTE bits to free up bits 3, 4, 5 and 6,
in the 4K backed HPTE pages.These bits continue to be used
for 64K backed HPTE pages in this patch, but will be freed
up in the next patch. The bit numbers are big-endian as
defined in the ISA3.0

The patch does the following change to the 4k HTPE backed
64K PTE's format.

H_PAGE_BUSY moves from bit 3 to bit 9 (B bit in the figure
		below)
V0 which occupied bit 4 is not used anymore.
V1 which occupied bit 5 is not used anymore.
V2 which occupied bit 6 is not used anymore.
V3 which occupied bit 7 is not used anymore.

Before the patch, the 4k backed 64k PTE format was as follows

 0 1 2 3 4  5  6  7  8 9 10...........................63
 : : : : :  :  :  :  : : :                            :
 v v v v v  v  v  v  v v v                            v

,-,-,-,-,--,--,--,--,-,-,-,-,-,------------------,-,-,-,
|x|x|x|B|V0|V1|V2|V3|x| | |x|x|................|x|x|x|x| <- primary pte
'_'_'_'_'__'__'__'__'_'_'_'_'_'________________'_'_'_'_'
|S|G|I|X|S |G |I |X |S|G|I|X|..................|S|G|I|X| <- secondary pte
'_'_'_'_'__'__'__'__'_'_'_'_'__________________'_'_'_'_'

After the patch, the 4k backed 64k PTE format is as follows

 0 1 2 3 4  5  6  7  8 9 10...........................63
 : : : : :  :  :  :  : : :                            :
 v v v v v  v  v  v  v v v                            v

,-,-,-,-,--,--,--,--,-,-,-,-,-,------------------,-,-,-,
|x|x|x| |  |  |  |  |x|B| |x|x|................|.|.|.|.| <- primary pte
'_'_'_'_'__'__'__'__'_'_'_'_'_'________________'_'_'_'_'
|S|G|I|X|S |G |I |X |S|G|I|X|..................|S|G|I|X| <- secondary pte
'_'_'_'_'__'__'__'__'_'_'_'_'__________________'_'_'_'_'

the four bits S,G,I,X (one quadruplet per 4k HPTE) that
cache the hash-bucket slot value, is initialized to
1,1,1,1 indicating -- an invalid slot. If a HPTE gets
cached in a 1111 slot(i.e 7th slot of secondary hash
bucket), it is released immediately. In other words,
even though 1111 is a valid slot value in the hash
bucket, we consider it invalid and release the slot and
the HPTE. This gives us the opportunity to determine
the validity of S,G,I,X bits based on its contents and
not on any of the bits V0,V1,V2 or V3 in the primary PTE

When we release a HPTE cached in the 1111 slot
we also release a legitimate slot in the primary
hash bucket and unmap its corresponding HPTE. This
is to ensure that we do get a HPTE cached in a slot
of the primary hash bucket, the next time we retry.

Though treating 1111 slot as invalid, reduces the
number of available slots in the hash bucket and may
have an effect on the performance, the probabilty of
hitting a 1111 slot is extermely low.

Compared to the current scheme, the above scheme
reduces the number of false hash table updates
significantly and has the added advantage of releasing
four valuable PTE bits for other purpose.

NOTE:even though bits 3, 4, 5, 6, 7 are not used when
the 64K PTE is backed by 4k HPTE, they continue to be
used if the PTE gets backed by 64k HPTE. The next
patch will decouple that aswell, and truely release the
bits.

This idea was jointly developed by Paul Mackerras,
Aneesh, Michael Ellermen and myself.

4K PTE format remains unchanged currently.

The patch does the following code changes
a) PTE flags are split between 64k and 4k header files.
b) __hash_page_4K() is reimplemented to reflect the
 above logic.
Acked-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Introduce pte_get_hash_gslot()() which returns the global slot number of
the HPTE in the global hash table.

This function will come in handy as we work towards re-arranging the PTE
bits in the later patches.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Introduce pte_set_hidx().It sets the (H_PAGE_F_SECOND|H_PAGE_F_GIX) bits
at the appropriate location in the PTE of 4K PTE. For 64K PTE, it sets
the bits in the second part of the PTE. Though the implementation for
the former just needs the slot parameter, it does take some additional
parameters to keep the prototype consistent.

This function will be handy as we work towards re-arranging the bits in
the subsequent patches.
Acked-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

GCC 7 will take "r2" in clobber list as an error and it will get
following build errors for powerpc ptrace selftests even with -fno-pic
option:
  ptrace-tm-vsx.c: In function ‘tm_vsx’:
  ptrace-tm-vsx.c:42:2: error: PIC register clobbered by ‘r2’ in ‘asm’
    asm __volatile__(
    ^~~
  make[1]: *** [ptrace-tm-vsx] Error 1
  ptrace-tm-spd-vsx.c: In function ‘tm_spd_vsx’:
  ptrace-tm-spd-vsx.c:55:2: error: PIC register clobbered by ‘r2’ in ‘asm’
    asm __volatile__(
    ^~~
  make[1]: *** [ptrace-tm-spd-vsx] Error 1
  ptrace-tm-spr.c: In function ‘tm_spr’:
  ptrace-tm-spr.c:46:2: error: PIC register clobbered by ‘r2’ in ‘asm’
    asm __volatile__(
    ^~~

Fix the build error by removing "r2" from the clobber list. None of
these asm blocks actually clobber r2.
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add a pci_vf_drivers_autoprobe() interface. Setting autoprobe to false
on the PF prevents drivers from binding to VFs when they are enabled.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add calls for pseries platform to configure/deconfigure SR-IOV.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@us.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

SR-IOV can now be enabled for the powernv platform and pseries
platform. Therefore move the appropriate calls to machine dependent
code instead of relying on definition at compile time.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@us.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc64 gcc can generate code that offsets an address, to access
part of an object in memory. If the address is a -mcmodel=medium toc
pointer relative address then code like the following is possible.

  addis r9,r2,var@toc@ha
  ld r3,var@toc@l(r9)
  ld r4,(var+8)@toc@l(r9)

This works fine so long as var is naturally aligned, *and* r2 is
sufficiently aligned. If not, there is a possibility that the offset
added to access var+8 wraps over a n*64k+32k boundary. Modules don't
have any guarantee that r2 is sufficiently aligned. Moreover, code
generated by older compilers generates a .toc section with 2**0
alignment, which can result in relocation failures at module load time
even without the wrap problem.

Thus, this patch links modules with an aligned .toc section (Makefile
and module.lds changes), and forces alignment for out of tree modules
or those without a .toc section (module_64.c changes).
Signed-off-by: Alan Modra <amodra@gmail.com>
[desnesn: updated patch to apply to powerpc-next kernel v4.15 ]
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com>
[mpe: Fix out-of-tree build, swap -256 for ~0xff, reflow comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When an interrupt is returning to a soft-disabled context (which can
happen for non-maskable interrupts or synchronous interrupts), it goes
through the motions of soft-disabling again, including calling
TRACE_DISABLE_INTS (i.e., trace_hardirqs_off()).

This is not necessary, because we must already be soft-disabled in the
interrupt context, it also may be causing crashes in the irq tracing
code to re-enter as an nmi. Replace it with a warning to ensure that
soft-interrupts are still disabled.

Fixes: 7c0482e3 ("powerpc/irq: Fix another case of lazy IRQ state getting out of sync")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add irq error handlers for cmu, plb, opb, mcue, conf
with debug information output in case of problems.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

TVSENSE(temperature and voltage sensors) reset is blocked (clock gated)
by the POR default of the TVS sleep config bit. As a consequence,
TVSENSE will provide erratic sensor values, which may result in
spurious (parity) errors recorded in the CMU FIR and leading to
erroneous interrupt requests once the CMU interrupt is unmasked.
Purpose of this to set up CMU in working state in any cases even
in case of parity errors.
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

* clear out any possible plb6 errors
* board interrupt handling setup within l2 reg set
* fsp2 parity error setup

All those points are needed for correct interrupt
handling on board level including error handling report.
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add cmu, plbX, l2, ddr3/4, crcs register definitions.
Add mfcmu, mtcmu functions for indirect access to cmu.
Add mtl2, mfl2 same for l2 cache core reg set.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Match powerpc/64 and include .data.rel* input sections in the .data output
section explicitly.

This solves the warning:

powerpc-linux-gnu-ld: warning: orphan section `.data.rel.ro' from `arch/powerpc/kernel/head_44x.o' being placed in section `.data.rel.ro'.

Link: https://lists.01.org/pipermail/kbuild-all/2017-November/040010.htmlReported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

As far as I can tell CONFIG_CPM is the right symbol to use to
conditionally compile the cpm-serial.c code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Only build the OPAL console code in when necessary. This looks like it
should use CONFIG_PPC_POWERNV, but because the opal-call.S code is
64-bit only, we must only build it when we're building the boot
wrapper 64-bit.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The serial code in uartlite.c only matches if we find one of two
Xilinx (xlnx) nodes in the device tree, there's no need to build or
link the code on other platforms.

As far as I can tell CONFIG_XILINX_VIRTEX is the appropriate symbol to
use to conditionally compile the code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Print the function address associated with the restore_r2() error to
make it easier to debug the problem.

Also clarify the wording a bit.

Before:

  module_64: patch_foo: Expect noop after relocate, got 3c820000

After:

  module_64: patch_foo: Expected nop after call, got 7c630034 at netdev_has_upper_dev+0x54/0xb0 [patch_foo]
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
[mpe: Change noop to nop, as that's the name of the instruction]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When attempting to load a livepatch module, I got the following error:

  module_64: patch_module: Expect noop after relocate, got 3c820000

The error was triggered by the following code in
unregister_netdevice_queue():

  14c:   00 00 00 48     b       14c <unregister_netdevice_queue+0x14c>
                         14c: R_PPC64_REL24      net_set_todo
  150:   00 00 82 3c     addis   r4,r2,0

GCC didn't insert a nop after the branch to net_set_todo() because it's
a sibling call, so it never returns.  The nop isn't needed after the
branch in that case.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-and-tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Livepatch re-uses module loader function apply_relocate_add() to write
relocations, instead of managing them by arch-dependent
klp_write_module_reloc() function.

apply_relocate_add() doesn't understand livepatch symbols (marked with
SHN_LIVEPATCH symbol section index) and assumes them to be local
symbols by default for R_PPC64_REL24 relocation type. It fails with an
error, when trying to calculate offset with local_entry_offset():

  module_64: kpatch_meminfo: REL24 -1152921504897399800 out of range!

Whereas livepatch symbols are essentially SHN_UNDEF, should be called
via stub used for global calls. This issue can be fixed by teaching
apply_relocate_add() to handle both SHN_UNDEF/SHN_LIVEPATCH symbols
via the same stub. This patch extends SHN_UNDEF code to handle
livepatch symbols too.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This message isn't terribly useful.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This statement causes some not very useful messages to always
be printed on the serial port at boot, even on quiet boots.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Current vDSO64 implementation does not have support for coarse clocks
(CLOCK_MONOTONIC_COARSE, CLOCK_REALTIME_COARSE), for which it falls back
to system call, increasing the response time, vDSO implementation reduces
the cycle time. Below is a benchmark of the difference in execution times.

(Non-coarse clocks are also included just for completion)

clock-gettime-realtime: syscall: 172 nsec/call
clock-gettime-realtime:    libc: 28 nsec/call
clock-gettime-realtime:    vdso: 22 nsec/call
clock-gettime-monotonic: syscall: 171 nsec/call
clock-gettime-monotonic:    libc: 30 nsec/call
clock-gettime-monotonic:    vdso: 25 nsec/call
clock-gettime-realtime-coarse: syscall: 153 nsec/call
clock-gettime-realtime-coarse:    libc: 16 nsec/call
clock-gettime-realtime-coarse:    vdso: 10 nsec/call
clock-gettime-monotonic-coarse: syscall: 167 nsec/call
clock-gettime-monotonic-coarse:    libc: 17 nsec/call
clock-gettime-monotonic-coarse:    vdso: 11 nsec/call

CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The workqueue "ps3av->wq" queues a single work item &ps3av->work and hence
doesn't require ordering. It is involved in waking up ps3avd to do the
video mode setting and hence it's not being used on a memory reclaim
path. Hence, it has been converted to use system_wq.

System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.

The work item has been flushed in ps3av_remove to ensure that
there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Instead of manually coding the loop with of_find_node_by_name(), let's
switch to the standard macro for iterating over nodes with given name.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[mpe: Fix build failures due to typo in mpc832x_mds.c]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We are not using result, so this simply results in a leaked refcount.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We need to call of_node_put() for device nodes obtained with
of_find_node_by_name().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

At some point, pr_warning will be removed so all logging messages use
a consistent <prefix>_warn style.

Update arch/powerpc/

Miscellanea:

o Coalesce formats
o Realign arguments
o Use %s, __func__ instead of embedded function names
o Remove unnecessary line continuations
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Geoff Levand <geoff@infradead.org>
[mpe: Rebase due to some %pOF changes.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Pull ARM fix from Russell King:
 "Just one fix this time around, for the late commit in the merge window
  that triggered a problem with qemu. Qemu is apparently also going to
  receive a fix for the discovered issue"

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: avoid faulting on qemu

Pull i2c fixes from Wolfram Sang:
 "Here are two bugfixes for I2C, fixing a memleak in the core and irq
  allocation for i801.

  Also three bugfixes for the at24 eeprom driver which Bartosz collected
  while taking over maintainership for this driver"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  eeprom: at24: check at24_read/write arguments
  eeprom: at24: fix reading from 24MAC402/24MAC602
  eeprom: at24: correctly set the size for at24mac402
  i2c: i2c-boardinfo: fix memory leaks on devinfo
  i2c: i801: Fix Failed to allocate irq -2147483648 error

Merge tag 'hwmon-for-linus-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Fixes:

   - Drop reference to obsolete maintainer tree

   - Fix overflow bug in pmbus driver

   - Fix SMBUS timeout problem in jc42 driver

  For the SMBUS timeout handling, we had a brief discussion if this
  should be considered a bug fix or a feature. Peter says "it fixes real
  problems where the application misbehave due to faulty content when
  reading from an eeprom", and he needs the patch in his company's v4.14
  images. This is good enough for me and warrants backport to stable
  kernels"

* tag 'hwmon-for-linus-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (jc42) optionally try to disable the SMBUS timeout
  hwmon: (pmbus) Use 64bit math for DIRECT format values
  hwmon: Drop reference to Jean's tree

Merge tag 'at24-4.15-fixes-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-current

Please consider pulling the following fixes for v4.15. While it doesn't
fix any regression introduced in the v4.15 merge window, we have a
feature in at24 since linux v4.8 - reading the mac address block from
at24mac series - which turned out to be not working.

This pull request contains changes that fix it together with a patch
that hardens the read and write argument sanitization with
out-of-bounds checks that were missing.

Pull NFS client fixes from Anna Schumaker:
 "These patches fix a problem with compiling using an old version of
  gcc, and also fix up error handling in the SUNRPC layer.

   - NFSv4: Ensure gcc 4.4.4 can compile initialiser for
     "invalid_stateid"

   - SUNRPC: Allow connect to return EHOSTUNREACH

   - SUNRPC: Handle ENETDOWN errors"

* tag 'nfs-for-4.15-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  SUNRPC: Handle ENETDOWN errors
  SUNRPC: Allow connect to return EHOSTUNREACH
  NFSv4: Ensure gcc 4.4.4 can compile initialiser for "invalid_stateid"

Pull xfs fixes from Darrick Wong:
 "Here are some bug fixes for 4.15-rc2.

   - fix memory leaks that appeared after removing ifork inline data
     buffer

   - recover deferred rmap update log items in correct order

   - fix memory leaks when buffer construction fails

   - fix memory leaks when bmbt is corrupt

   - fix some uninitialized variables and math problems in the quota
     scrubber

   - add some omitted attribution tags on the log replay commit

   - fix some UBSAN complaints about integer overflows with large sparse
     files

   - implement an effective inode mode check in online fsck

   - fix log's inability to retry quota item writeout due to transient
     errors"

* tag 'xfs-4.15-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: Properly retry failed dquot items in case of error during buffer writeback
  xfs: scrub inode mode properly
  xfs: remove unused parameter from xfs_writepage_map
  xfs: ubsan fixes
  xfs: calculate correct offset in xfs_scrub_quota_item
  xfs: fix uninitialized variable in xfs_scrub_quota
  xfs: fix leaks on corruption errors in xfs_bmap.c
  xfs: fortify xfs_alloc_buftarg error handling
  xfs: log recovery should replay deferred ops in order
  xfs: always free inline data before resetting inode fork during ifree

Merge tag 'riscv-for-linus-4.15-rc2_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/linux

Pull RISC-V cleanups and ABI fixes from Palmer Dabbelt:
 "This contains a handful of small cleanups that are a result of
  feedback that didn't make it into our original patch set, either
  because the feedback hadn't been given yet, I missed the original
  emails, or we weren't ready to submit the changes yet.

  I've been maintaining the various cleanup patch sets I have as their
  own branches, which I then merged together and signed. Each merge
  commit has a short summary of the changes, and each branch is based on
  your latest tag (4.15-rc1, in this case). If this isn't the right way
  to do this then feel free to suggest something else, but it seems sane
  to me.

  Here's a short summary of the changes, roughly in order of how
  interesting they are.

   - libgcc.h has been moved from include/lib, where it's the only
     member, to include/linux. This is meant to avoid tab completion
     conflicts.

   - VDSO entries for clock_get/gettimeofday/getcpu have been added.
     These are simple syscalls now, but we want to let glibc use them
     from the start so we can make them faster later.

   - A VDSO entry for instruction cache flushing has been added so
     userspace can flush the instruction cache.

   - The VDSO symbol versions for __vdso_cmpxchg{32,64} have been
     removed, as those VDSO entries don't actually exist.

   - __io_writes has been corrected to respect the given type.

   - A new READ_ONCE in arch_spin_is_locked().

   - __test_and_op_bit_ord() is now actually ordered.

   - Various small fixes throughout the tree to enable allmodconfig to
     build cleanly.

   - Removal of some dead code in our atomic support headers.

   - Improvements to various comments in our atomic support headers"

* tag 'riscv-for-linus-4.15-rc2_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/linux: (23 commits)
  RISC-V: __io_writes should respect the length argument
  move libgcc.h to include/linux
  RISC-V: Clean up an unused include
  RISC-V: Allow userspace to flush the instruction cache
  RISC-V: Flush I$ when making a dirty page executable
  RISC-V: Add missing include
  RISC-V: Use define for get_cycles like other architectures
  RISC-V: Provide stub of setup_profiling_timer()
  RISC-V: Export some expected symbols for modules
  RISC-V: move empty_zero_page definition to C and export it
  RISC-V: io.h: type fixes for warnings
  RISC-V: use RISCV_{INT,SHORT} instead of {INT,SHORT} for asm macros
  RISC-V: use generic serial.h
  RISC-V: remove spin_unlock_wait()
  RISC-V: `sfence.vma` orderes the instruction cache
  RISC-V: Add READ_ONCE in arch_spin_is_locked()
  RISC-V: __test_and_op_bit_ord should be strongly ordered
  RISC-V: Remove smb_mb__{before,after}_spinlock()
  RISC-V: Remove __smp_bp__{before,after}_atomic
  RISC-V: Comment on why {,cmp}xchg is ordered how it is
  ...

Pull arm64 fixes from Will Deacon:
 "The critical one here is a fix for fpsimd register corruption across
  signals which was introduced by the SVE support code (the register
  files overlap), but the others are worth having as well.

  Summary:

   - Fix FP register corruption when SVE is not available or in use

   - Fix out-of-tree module build failure when CONFIG_ARM64_MODULE_PLTS=y

   - Missing 'const' generating errors with LTO builds

   - Remove unsupported events from Cortex-A73 PMU description

   - Removal of stale and incorrect comments"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: context: Fix comments and remove pointless smp_wmb()
  arm64: cpu_ops: Add missing 'const' qualifiers
  arm64: perf: remove unsupported events for Cortex-A73
  arm64: fpsimd: Fix failure to restore FPSIMD state after signals
  arm64: pgd: Mark pgd_cache as __ro_after_init
  arm64: ftrace: emit ftrace-mod.o contents through code
  arm64: module-plts: factor out PLT generation code for ftrace
  arm64: mm: cleanup stale AIVIVT references

Olaf said: Here's a short series of patches that produces a working
allmodconfig. Would be nice to see them go in so we can add build
coverage.

I've dropped patches 8 and 10 from the original set:

* [PATCH 08/10] (RISC-V: Set __ARCH_WANT_RENAMEAT to pick up generic
  version) has a better fix that I've sent out for review, we don't want
  renameat.
* [PATCH 10/10] (input: joystick: riscv has get_cycles) has already been
  taken into Dmitry Torokhov's tree.