Prepare for later dts.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

We've made generic irqchip drivers for Loongson-3 platform, it's time
to say goodbye to these legacy code.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Document Loongson-3 HyperTransport PIC controller.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

This controller appeared on Loongson-3 family of chips to receive
interrupts from PCH PIC.
It is a I8259 with optimized interrupt polling flow. We can poll
interrupt number from HT vector directly but still have to follow
standard I8259 routines to mask, unmask and EOI.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Document Loongson I/O Interrupt controller.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

The 1.0 version of that controller has a bug that status bit
of LPC IRQ sometimes doesn't get set correctly.

So we can always blame LPC IRQ when spurious interrupt happens
at the parent interrupt line which LPC IRQ supposed to route
to.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

This controller appeared on Loongson family of chips as the primary
package interrupt source.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Since the au1xxx-ide IDE host driver is no longer needed its documentation
can be removed.
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Since the only user of this header (au1xxx-ide IDE host driver) is
now gone it can also be removed.
Acked-by: Paul Burton <paulburton@kernel.org>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Commit 54ff4a1d ("MIPS: Alchemy: pata_platform for DB1200")
from year 2014 converted the only user of au1xxx-ide IDE host
driver (MIPS Alchemy DB1200 platform) to use pata_platform
libata host driver instead. This patch removes dead au1xxx-ide
driver code.
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Enable DMI scanning on the MIPS architecture, this setups DMI identifiers
(dmi_system_id) for printing it out on task dumps and prepares DIMM entry
information (dmi_memdev_info) from the SMBIOS table. With this patch, the
driver can easily match various of mainboards.

In the SMBIOS reference specification, the table anchor string "_SM_" is
present in the address range 0xF0000 to 0xFFFFF on a 16-byte boundary,
but there exists a special case for Loongson platform, when call function
dmi_early_remap, it should specify the start address to 0xFFFE000 due to
it is reserved for SMBIOS and can be normally access in the BIOS.

This patch works fine on the Loongson 3A3000 platform which belongs to
MIPS architecture and has no influence on the other architectures such
as x86 and ARM.

Additionally, in order to avoid the unknown risks on the mips platform
which is not MACH_LOONGSON64, the DMI config is better to depend on
MACH_LOONGSON64. If other mips platform also needs this DMI feature in
the future, the "depends on" condition can be modified.
Co-developed-by: Yinglu Yang <yangyinglu@loongson.cn>
Signed-off-by: Yinglu Yang <yangyinglu@loongson.cn>
[jiaxun.yang@flygoat.com: Refine definitions and Kconfig]
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Use SMBIOS_ENTRY_POINT_SCAN_START instead of 0xF0000, because other
archtecture maybe use a special start address such as 0xFFFE000 for
Loongson platform.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

mt7621 SoC has its own 'ralink_soc_info' structure with some
information about the soc itself. Pcie controller and pcie phy
drivers for this soc which are still in staging git tree make uses
of 'soc_device_attribute' looking for revision 'E2' in order to
know if reset lines are or not inverted. This way of doing things
seems to be necessary in order to make things clean and properly.
Hence, introduce this 'soc_device' to be able to properly use those
attributes in drivers. Also set 'data' pointer points to the struct
'ralink_soc_info' to be able to export also current soc information
using this mechanism.

Cc: Paul Burton <paul.burton@mips.com>
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: john@phrozen.org
Cc: NeilBrown <neil@brown.name>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

a) configure for supporting modules

Not all drivers need to be compiled into the kernel.
Support building and loading of kernel modules.

b) compile leds-gpio driver into the kernel and configure for LED triggers

DTS has been augmented to add some gpio-leds. We need the leds-gpio driver
and enable the triggers.

c) configure CONFIG_REGULATOR_ACT8865 for PMU

The PMU on the CI20 board is an ACT8600 using the ACT8865 driver.
Since it is not compiled, the PMU and the CI20 board is running in
power-on reset state of the PMU.

d) compile gpio-ir driver

The CI20 board has a gpio based IR receiver.

e) configure for CONFIG_KEYBOARD_GPIO=m

The SW1 button is hooked up to send input events.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

a) add DT node for SW1 as Enter button

The SW1 button can be used as a simple one-button keyboard
and is connected to PD17.

Note: SW1 has a second meaning to change the boot sequence
when pressed while powering on.

b) give eth0_power a defined voltage.

This is a 3.3V power switch (DVNET3.3V).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

The infrared sensor on the CI20 board is connected to a GPIO and can
be operated by using the gpio-ir-recv driver. Add a DT node for the
sensor to allow that driver to be used.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Pull in mips-fixes avoiding conflicts with more CI20 DT changes.

A few MIPS fixes:

- DT fixes for CI20

- Fix command line handling

- Correct patchwork URL
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Fix the following checkpatch error:

ERROR: do not initialise statics to 0
#125: FILE: loongson64/numa.c:125:
+	static unsigned long num_physpages = 0;
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

There are some common header files which are referenced locally
with #includenext method, includenext is tricky method and only
used on mips platform.

This patech removes includenext method, replace it with defailed
pathname prefix for header files.

This patch passes to compile on all mips platform with defconfig,
and is verified on my loongson64 box.

Changes:
--------
v2:
  - Fix compiling issue on malta platform
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: bibo mao <maobibo@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Some userland application/program runtime/dynamic loaded need to
know about the current ISA level to use the best runtime.
While kernel doesn't provides this info.

ELF_PLATFORM only provides some info about the CPU, with very few info,
for example, the value is "mips" for both 24Kc and P6600.

Currently ELF_BASE_PLATFORM is not used by MIPS (only by powerpc).
So we cant set its value as:
  mips2, mips3, mips4, mips5,
  mips32, mips32r2, mips32r6
  mips64, mips64r2, mips64r6
Then in userland, we can get it by:
  getauxval(AT_BASE_PLATFORM)

The only problem is that it seems has different defination than ppc:
  on ppc, it is the mircoarchitecture
while now we use it as ISA level on MIPS.
Signed-off-by: YunQiang Su <syq@debian.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Zephyr secondary cache is 256KB, 128B lines. 32B sectors. A secondary cache
line can contain two instruction cache lines (64B), or four data cache
lines (32B). Hardware prefetch Cache detects stream access, and prefetches
ahead of processor access. Add support to invalidate BMIPS5000 cpu zephyr
secondary cache module (ZSCM) on DMA from device so that data returned is
coherent during DMA read operations.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Recently all usages of setup_irq() was replaced by request_irq().
request_irq() does a few sanity checks that were not done in
setup_irq(), if they fail irq registration will fail. One of the check
is to ensure that non-NULL dev_id is passed in the case of shared irq.
This caused malta on qemu to hang.

Fix it by passing handler as dev_id to all request_irq()'s that are
shared. For sni, instead of passing non-NULL dev_id, remove shared irq
flags.

Fixes: ac8fd122 ("MIPS: Replace setup_irq() by request_irq()")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS patchwork lives on patchwork.kernel.org for quite some time.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Interrupts should not be specified by interrupt line but by
gpio parent and reference.

Fixes: 73f2b940 ("MIPS: CI20: DTS: Add I2C nodes")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

There is a ACT8600 on the CI20 board and the bindings of the
ACT8865 driver have changed without updating the CI20 device
tree. Therefore the PMU can not be probed successfully and
is running in power-on reset state.

Fix DT to match the latest act8865-regulator bindings.

Fixes: 73f2b940 ("MIPS: CI20: DTS: Add I2C nodes")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

request_irq() is preferred over setup_irq(). Invocations of setup_irq()
occur after memory allocators are ready.

Per tglx[1], setup_irq() existed in olden days when allocators were not
ready by the time early interrupts were initialized.

Hence replace setup_irq() by request_irq().

remove_irq() has been replaced by free_irq() as well.

There were build error's during previous version, couple of which was
reported by kbuild test robot <lkp@intel.com> of which one was reported
by Thomas Bogendoerfer <tsbogend@alpha.franken.de> as well. There were a
few more issues including build errors, those also have been fixed.

[1] https://lkml.kernel.org/r/alpine.DEB.2.20.1710191609480.1971@nanosSigned-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

There is a potential NULL pointer dereference in case kzalloc()
fails and returns NULL.

Fix this by adding a NULL check on *cd*

This bug was detected with the help of Coccinelle.

Fixes: 64b139f9 ("MIPS: OCTEON: irq: add CIB and other fixes")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Fix wording in NUMA help text.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Default printk log level is KERN_WARNING. This makes automatic log
parsing problematic, since we get false positive alarms on not critical
information.

Set all not critical cache related information to KERN_INFO, the same level
as used on most kernel drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

There is no need to have the 'struct device_node *node' variable static
since new value always be assigned before use it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

The CONFIG_MIPS_CMDLINE_DTB_EXTEND option is used so that the kernel
arguments provided in the 'bootargs' property in devicetree are extended
with the kernel arguments provided by the bootloader.

The code was broken, as it didn't actually take any of the kernel
arguments provided in devicetree when that option was set.

Fixes: 7784cac6 ("MIPS: cmdline: Clean up boot_command_line initialization")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

My time with MIPS the company has reached its end, and so at best I'll
have little time spend on maintaining arch/mips/.

Ralf last authored a patch over 2 years ago, the last time he committed
one is even further back & activity was sporadic for a while before
that. The reality is that he isn't active.

Having a new maintainer with time to do things properly will be
beneficial all round. Thomas Bogendoerfer has been involved in MIPS
development for a long time & has offered to step up as maintainer, so
add Thomas and remove myself & Ralf from the MIPS entry.

Ralf already has an entry in CREDITS to honor his contributions, so this
just adds one for me.
Signed-off-by: Paul Burton <paulburton@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@vger.kernel.org

Enable some options for machine type, framebuffer, serial controller and
ATA interfaces.

This allows a jazz_defconfig build to work on the emulated MIPS Magnum
machine provided by qemu-system-mips64el.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

Remove some redundant assignments, that have no effect on
'make jazz_defconfig':

CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_CRYPTO_HMAC=y

Also drop the settings relating to crypto, wireless, advanced
networking etc. The Kconfig defaults for these options are fine.

This reduces the size of vmlinux so it can be launched by
"NetBSD/arc Bootstrap, Revision 1.1", which is conveniently available
on NetBSD/arc 5.1 ISO images.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

This patch resolves these compiler errors and warnings --

  CC      drivers/video/fbdev/g364fb.o
drivers/video/fbdev/g364fb.c: In function 'g364fb_cursor':
drivers/video/fbdev/g364fb.c:137:9: error: 'x' undeclared (first use in this function)
drivers/video/fbdev/g364fb.c:137:9: note: each undeclared identifier is reported only once for each function it appears in
drivers/video/fbdev/g364fb.c:137:7: error: implicit declaration of function 'fontwidth' [-Werror=implicit-function-declaration]
drivers/video/fbdev/g364fb.c:137:23: error: 'p' undeclared (first use in this function)
drivers/video/fbdev/g364fb.c:137:38: error: 'y' undeclared (first use in this function)
drivers/video/fbdev/g364fb.c:137:7: error: implicit declaration of function 'fontheight' [-Werror=implicit-function-declaration]
drivers/video/fbdev/g364fb.c: In function 'g364fb_init':
drivers/video/fbdev/g364fb.c:233:24: error: 'fbvar' undeclared (first use in this function)
drivers/video/fbdev/g364fb.c:234:24: error: 'xres' undeclared (first use in this function)
drivers/video/fbdev/g364fb.c:201:14: warning: unused variable 'j' [-Wunused-variable]
drivers/video/fbdev/g364fb.c:197:25: warning: unused variable 'pal_ptr' [-Wunused-variable]

The MIPS Magnum framebuffer console now works when tested in QEMU.

Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org

The devicetree ABI was broken on purpose by commit 6d532143
("watchdog: jz4740: Use regmap provided by TCU driver"), and
commit 1d9c3074 ("watchdog: jz4740: Use WDT clock provided
by TCU driver"). The commit message of the latter explains why the ABI
was broken.

However, the current devicetree files were not updated to the new ABI
described in Documentation/devicetree/bindings/timer/ingenic,tcu.txt,
so the watchdog driver would not probe.

Fix this problem by updating the watchdog nodes to comply with the new
ABI.

Fixes: 6d532143 ("watchdog: jz4740: Use regmap provided by TCU driver")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Zhou Yanjie <zhouyanjie@wanyeetech.com>
Cc: od@zcrc.me
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # v5.5+

The devicetree ABI was broken on purpose by commit 6d532143
("watchdog: jz4740: Use regmap provided by TCU driver"), and
commit 1d9c3074 ("watchdog: jz4740: Use WDT clock provided
by TCU driver"). The commit message of the latter explains why the ABI
was broken.

However, the current devicetree files were not updated to the new ABI
described in Documentation/devicetree/bindings/timer/ingenic,tcu.txt,
so the watchdog driver would not probe.

Fix this problem by updating the clock of watchdog node from
"&cgu X1000_CLK_RTCLK" to "&tcu TCU_CLK_WDT" to comply with the new
ABI.

Fixes: 7a16ccd3 ("[v8,1/4] MIPS: Ingenic: Add Ingenic X1000 support.").
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: paul@crapouillou.net
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: ralf@linux-mips.org
Cc: sernia.zhou@foxmail.com
Cc: zhenwenjin@gmail.com
Cc: dongsheng.qiu@ingenic.com

CONFIG_MTD_NAND_IDS is gone and not needed (part of CONFIG_MTD_NAND)
since commit f16bd7ca ("mtd: nand: Kill the MTD_NAND_IDS Kconfig
option").

CONFIG_IOSCHED_DEADLINE, CONFIG_IOSCHED_CFQ and CONFIG_DEFAULT_NOOP are
gone since commit f382fb0b ("block: remove legacy IO schedulers").

The IOSCHED_DEADLINE was replaced by MQ_IOSCHED_DEADLINE and it will be
now enabled by default (along with MQ_IOSCHED_KYBER).

The BFQ_GROUP_IOSCHED is the only multiqueue scheduler which comes with
group scheduling so select it in configs previously choosing
CFQ_GROUP_IOSCHED.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org

The Ralink platform code is not a clock provider, and just needs to call
of_clk_init().

Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: James Hartley <james.hartley@sondrel.com>
Cc: linux-mips@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-clk@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

The Pistachio platform code is not a clock provider, and just needs to
call of_clk_init().

Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: James Hartley <james.hartley@sondrel.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-clk@vger.kernel.org
Cc: linux-kernel@vger.kernel.org