This fixes the module init message to tell that the legacy
driver loaded. This makes it less confusing, in case both drivers are loaded.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Replace broken code that attempted to copy 6 byte array to 64-bit
integer. Due to missing cast to 64-bit integer, left shift operation
were 32-bit and lead to bytes been copied over each other. New code
uses simple memcpy, for greater readability and efficiency.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

instead of with itself.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Slightly more useful if we compare it against the sequence number of the
command we have outstanding, rather than comparing the reply with itself.

Doh. Pointed out by Sebastian Siewior
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When I called p54_parse_eeprom() on a hand-coded structure
I managed to make a small mistake with wrap->len which caused
a segfault a few lines down when trying to read entry->len.
This patch changes the validation code to avoid such problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since the EEPROM structure is read from hardware, it is
always little endian, annotate that in the struct and
make sure to convert where applicable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Wu <flamingice@sourmilk.net>
Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch has added pcibios_enable_device() return value check.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge rate_control_pid_shift_adjust() to rate_control_pid_adjust_rate()
in order to make the learning algorithm aware of constraints on rates. Also
add some comments and rename variables.

This fixes a bug which prevented 802.11b/g non-AP STAs from working with
802.11b only AP STAs.

This patch was originally destined for 2.6.26, and is being backported
to fix a user reported problem in post-2.6.24 kernels.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Every skb removed from session->reorder_q needs sock_put().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Every skb removed from session->reorder_q needs sock_put().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the l2cap info_timer is active the info_state will be set to
L2CAP_INFO_FEAT_MASK_REQ_SENT, and it will be unset after the timer is
deleted or timeout triggered.

Here in l2cap_conn_del only call del_timer_sync when the info_state is
set to L2CAP_INFO_FEAT_MASK_REQ_SENT.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

neigh_update sends skb from neigh->arp_queue while neigh_timer_handler
has increased skbs refcount and calls solicit with the
skb. neigh_timer_handler should not increase skbs refcount but make a
copy of the skb and do solicit with the copy.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since a5fbb6d1
"KVM: fix !SMP build error" smp_call_function isn't a define anymore
that folds into nothing but a define that calls up_smp_call_function
with all parameters. Hence we cannot #ifdef out the unused code
anymore...
This seems to be the preferred method, so do this for s390 as well.

net/iucv/iucv.c: In function 'iucv_cleanup_queue':
net/iucv/iucv.c:657: error: '__iucv_cleanup_queue' undeclared
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It makes fackets_out to grow too slowly compared with the
real write queue.

This shouldn't cause those BUG_TRAP(packets <= tp->packets_out)
to trigger but how knows how such inconsistent fackets_out
affects here and there around TCP when everything is nowadays
assuming accurate fackets_out. So lets see if this silences
them all.

Reported by Guillaume Chazarain <guichaz@gmail.com>.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current tun/tap driver sets also net device's hw address when asked to
change character device's hw address. This is a good idea, but it
misses RTLN-locking, resulting following error message in 2.6.25-rc3's
inetdev_event() function:

RTNL: assertion failed at net/ipv4/devinet.c (1050)

Attached patch fixes this problem.
Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In addition to commit 160f17 ("[SCTP]: Use proc_create() to setup
->proc_fops first") use proc_create in two more places.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sangtae Ha <sha2@ncsu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new SCTP socket api (draft 16) updates the AUTH API structures.
We never exported these since we knew they would change.
Update the rest to match the draft.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

The chunks are stored inside a parameter structure in the kernel
and when we copy them to the user, we need to account for
the parameter header.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

I noticed while looking into some odd behavior in sctp, that the variable
name sctp_pf_inet6_specific was used twice to represent two different
pieces of data (its both a structure name and a pointer to that type of
structure), which is confusing to say the least, and potentially dangerous
depending on the variable scope.  This patch cleans that up, and makes the
protocol and address family registration names in SCTP more regular,
increasing readability.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

 ipv6.c     |   12 ++++++------
 protocol.c |   12 ++++++------
 2 files changed, 12 insertions(+), 12 deletions(-)

As Davem mentioned in his recently patch
(d9595a7b)
that the procfs visibility should occur after
the ->proc_fops are setup.

And also, Alexey provide proc_create() to make
sure that ->proc_fops is setup before gluing PDE
to main tree.

We use proc_create().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Several endianity corrections in start_xmit()

Fixed TSO bug where packets were missing the TCP flags.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Limit traffic through an internal queue to prevent overflow.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed locking between fastpath and slowpath operations.

Corrected order of traffic disabling to prevent race when going down
under traffic.

- first have the microcode drop all incoming packets
- then do the slowpath stuff
- only then reset the MAC

Got rid of in_reset_task.

Remove_one() and friends would deference a null pointer if init_one
failed.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>