- 24 Aug, 2017 2 commits
-
-
andy zhou authored
Current implementation treats the burst configuration the same as rate configuration. This can cause the per packet cost to be lower than configured. In effect, this bug causes the token bucket to be refilled at a higher rate than what user has specified. This patch changes the implementation so that the token bucket size is controlled by "rate + burst", while maintain the token bucket refill rate the same as user specified. Fixes: 96518518 ("netfilter: add nftables") Signed-off-by:
Andy Zhou <azhou@ovn.org> Acked-by:
Joe Stringer <joe@ovn.org> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
Xin Long authored
Commit 4440a2ab ("netfilter: synproxy: Check oom when adding synproxy and seqadj ct extensions") wanted to drop the packet when it fails to add seqadj ext due to no memory by checking if nfct_seqadj_ext_add returns NULL. But that nfct_seqadj_ext_add returns NULL can also happen when seqadj ext already exists in a nf_conn. It will cause that userspace protocol doesn't work when both dnat and snat are configured. Li Shuang found this issue in the case: Topo: ftp client router ftp server 10.167.131.2 <-> 10.167.131.254 10.167.141.254 <-> 10.167.141.1 Rules: # iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 21 -j \ DNAT --to-destination 10.167.141.1 # iptables -t nat -A POSTROUTING -o eth2 -p tcp -m tcp --dport 21 -j \ SNAT --to-source 10.167.141.254 In router, when both dnat and snat are added, nf_nat_setup_info will be called twice. The packet can be dropped at the 2nd time for DNAT due to seqadj ext is already added at the 1st time for SNAT. This patch is to fix it by checking for seqadj ext existence before adding it, so that the packet will not be dropped if seqadj ext already exists. Note that as Florian mentioned, as a long term, we should review ext_add() behaviour, it's better to return a pointer to the existing ext instead. Fixes: 4440a2ab ("netfilter: synproxy: Check oom when adding synproxy and seqadj ct extensions") Reported-by:
Li Shuang <shuali@redhat.com> Acked-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
- 31 Jul, 2017 1 commit
-
-
Taehee Yoo authored
If verdict is NF_STOLEN in the SYNPROXY target, the skb is consumed. However, ipt_do_table() always tries to get ip header from the skb. So that, KASAN triggers the use-after-free message. We can reproduce this message using below command. # iptables -I INPUT -p tcp -j SYNPROXY --mss 1460 [ 193.542265] BUG: KASAN: use-after-free in ipt_do_table+0x1405/0x1c10 [ ... ] [ 193.578603] Call Trace: [ 193.581590] <IRQ> [ 193.584107] dump_stack+0x68/0xa0 [ 193.588168] print_address_description+0x78/0x290 [ 193.593828] ? ipt_do_table+0x1405/0x1c10 [ 193.598690] kasan_report+0x230/0x340 [ 193.603194] __asan_report_load2_noabort+0x19/0x20 [ 193.608950] ipt_do_table+0x1405/0x1c10 [ 193.613591] ? rcu_read_lock_held+0xae/0xd0 [ 193.618631] ? ip_route_input_rcu+0x27d7/0x4270 [ 193.624348] ? ipt_do_table+0xb68/0x1c10 [ 193.629124] ? do_add_counters+0x620/0x620 [ 193.634234] ? iptable_filter_net_init+0x60/0x60 [ ... ] After this patch, only when verdict is XT_CONTINUE, ipt_do_table() tries to get ip header. Also arpt_do_table() is modified because it has same bug. Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
- 19 Jul, 2017 2 commits
-
-
Pablo Neira Ayuso authored
If the x_tables extension comes with no hook mask, skip this validation. Signed-off-by: -
Sabrina Dubroca authored
When we delete a netns with a CLUSTERIP rule, clusterip_net_exit() is called first, removing /proc/net/ipt_CLUSTERIP. Then clusterip_config_entry_put() is called from clusterip_tg_destroy(), and tries to remove its entry under /proc/net/ipt_CLUSTERIP/. Fix this by checking that the parent directory of the entry to remove hasn't already been deleted. The following triggers a KASAN splat (stealing the reproducer from 202f59af, thanks to Jianlin Shi and Xin Long): ip netns add test ip link add veth0_in type veth peer name veth0_out ip link set veth0_in netns test ip netns exec test ip link set lo up ip netns exec test ip link set veth0_in up ip netns exec test iptables -I INPUT -d 1.2.3.4 -i veth0_in -j \ CLUSTERIP --new --clustermac 89:d4:47:eb:9a:fa --total-nodes 3 \ --local-node 1 --hashmode sourceip-sourceport ip netns del test Fixes: ce4ff76c ("netfilter: ipt_CLUSTERIP: make proc directory per net namespace") Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Reviewed-by:
-
- 18 Jul, 2017 6 commits
-
-
Dan Carpenter authored
We accidentally return an uninitialized variable. Fixes: cf56c2f8 ("netfilter: remove old pre-netns era hook api") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for your net tree, they are: 1) Missing netlink message sanity check in nfnetlink, patch from Mateusz Jurczyk. 2) We now have netfilter per-netns hooks, so let's kill global hook infrastructure, this infrastructure is known to be racy with netns. We don't care about out of tree modules. Patch from Florian Westphal. 3) find_appropriate_src() is buggy when colissions happens after the conversion of the nat bysource to rhashtable. Also from Florian. 4) Remove forward chain in nf_tables arp family, it's useless and it is causing quite a bit of confusion, from Florian Westphal. 5) nf_ct_remove_expect() is called with the wrong parameter, causing kernel oops, patch from Florian Westphal. ==================== Signed-off-by: -
Paolo Abeni authored
Eric noticed that in udp_recvmsg() we still need to access skb->dst while processing the IP options. Since commit 0a463c78 ("udp: avoid a cache miss on dequeue") skb->dst is no more available at recvmsg() time and bad things will happen if we enter the relevant code path. This commit address the issue, avoid clearing skb->dst if any IP options are present into the relevant skb. Since the IP CB is contained in the first skb cacheline, we can test it to decide to leverage the consume_stateless_skb() optimization, without measurable additional cost in the faster path. v1 -> v2: updated commit message tags Fixes: 0a463c78 ("udp: avoid a cache miss on dequeue") Reported-by:
Andrey Konovalov <andreyknvl@google.com> Reported-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Christophe Jaillet authored
If 'dma_set_mask_and_coherent()' fails, we must undo the previous 'pci_request_regions()' call. Adjust corresponding 'goto' to jump at the right place of the error handling path. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Alexander Potapenko authored
KMSAN reported use of uninitialized memory in skb_set_hash_from_sk(), which originated from the TCP request socket created in cookie_v6_check(): ================================================================== BUG: KMSAN: use of uninitialized memory in tcp_transmit_skb+0xf77/0x3ec0 CPU: 1 PID: 2949 Comm: syz-execprog Not tainted 4.11.0-rc5+ #2931 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 TCP: request_sock_TCPv6: Possible SYN flooding on port 20028. Sending cookies. Check SNMP counters. Call Trace: <IRQ> __dump_stack lib/dump_stack.c:16 dump_stack+0x172/0x1c0 lib/dump_stack.c:52 kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:927 __msan_warning_32+0x61/0xb0 mm/kmsan/kmsan_instr.c:469 skb_set_hash_from_sk ./include/net/sock.h:2011 tcp_transmit_skb+0xf77/0x3ec0 net/ipv4/tcp_output.c:983 tcp_send_ack+0x75b/0x830 net/ipv4/tcp_output.c:3493 tcp_delack_timer_handler+0x9a6/0xb90 net/ipv4/tcp_timer.c:284 tcp_delack_timer+0x1b0/0x310 net/ipv4/tcp_timer.c:309 call_timer_fn+0x240/0x520 kernel/time/timer.c:1268 expire_timers kernel/time/timer.c:1307 __run_timers+0xc13/0xf10 kernel/time/timer.c:1601 run_timer_softirq+0x36/0xa0 kernel/time/timer.c:1614 __do_softirq+0x485/0x942 kernel/softirq.c:284 invoke_softirq kernel/softirq.c:364 irq_exit+0x1fa/0x230 kernel/softirq.c:405 exiting_irq+0xe/0x10 ./arch/x86/include/asm/apic.h:657 smp_apic_timer_interrupt+0x5a/0x80 arch/x86/kernel/apic/apic.c:966 apic_timer_interrupt+0x86/0x90 arch/x86/entry/entry_64.S:489 RIP: 0010:native_restore_fl ./arch/x86/include/asm/irqflags.h:36 RIP: 0010:arch_local_irq_restore ./arch/x86/include/asm/irqflags.h:77 RIP: 0010:__msan_poison_alloca+0xed/0x120 mm/kmsan/kmsan_instr.c:440 RSP: 0018:ffff880024917cd8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff10 RAX: 0000000000000246 RBX: ffff8800224c0000 RCX: 0000000000000005 RDX: 0000000000000004 RSI: ffff880000000000 RDI: ffffea0000b6d770 RBP: ffff880024917d58 R08: 0000000000000dd8 R09: 0000000000000004 R10: 0000160000000000 R11: 0000000000000000 R12: ffffffff85abf810 R13: ffff880024917dd8 R14: 0000000000000010 R15: ffffffff81cabde4 </IRQ> poll_select_copy_remaining+0xac/0x6b0 fs/select.c:293 SYSC_select+0x4b4/0x4e0 fs/select.c:653 SyS_select+0x76/0xa0 fs/select.c:634 entry_SYSCALL_64_fastpath+0x13/0x94 arch/x86/entry/entry_64.S:204 RIP: 0033:0x4597e7 RSP: 002b:000000c420037ee0 EFLAGS: 00000246 ORIG_RAX: 0000000000000017 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00000000004597e7 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: 000000c420037ef0 R08: 000000c420037ee0 R09: 0000000000000059 R10: 0000000000000000 R11: 0000000000000246 R12: 000000000042dc20 R13: 00000000000000f3 R14: 0000000000000030 R15: 0000000000000003 chained origin: save_stack_trace+0x37/0x40 arch/x86/kernel/stacktrace.c:59 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:302 kmsan_save_stack mm/kmsan/kmsan.c:317 kmsan_internal_chain_origin+0x12a/0x1f0 mm/kmsan/kmsan.c:547 __msan_store_shadow_origin_4+0xac/0x110 mm/kmsan/kmsan_instr.c:259 tcp_create_openreq_child+0x709/0x1ae0 net/ipv4/tcp_minisocks.c:472 tcp_v6_syn_recv_sock+0x7eb/0x2a30 net/ipv6/tcp_ipv6.c:1103 tcp_get_cookie_sock+0x136/0x5f0 net/ipv4/syncookies.c:212 cookie_v6_check+0x17a9/0x1b50 net/ipv6/syncookies.c:245 tcp_v6_cookie_check net/ipv6/tcp_ipv6.c:989 tcp_v6_do_rcv+0xdd8/0x1c60 net/ipv6/tcp_ipv6.c:1298 tcp_v6_rcv+0x41a3/0x4f00 net/ipv6/tcp_ipv6.c:1487 ip6_input_finish+0x82f/0x1ee0 net/ipv6/ip6_input.c:279 NF_HOOK ./include/linux/netfilter.h:257 ip6_input+0x239/0x290 net/ipv6/ip6_input.c:322 dst_input ./include/net/dst.h:492 ip6_rcv_finish net/ipv6/ip6_input.c:69 NF_HOOK ./include/linux/netfilter.h:257 ipv6_rcv+0x1dbd/0x22e0 net/ipv6/ip6_input.c:203 __netif_receive_skb_core+0x2f6f/0x3a20 net/core/dev.c:4208 __netif_receive_skb net/core/dev.c:4246 process_backlog+0x667/0xba0 net/core/dev.c:4866 napi_poll net/core/dev.c:5268 net_rx_action+0xc95/0x1590 net/core/dev.c:5333 __do_softirq+0x485/0x942 kernel/softirq.c:284 origin: save_stack_trace+0x37/0x40 arch/x86/kernel/stacktrace.c:59 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:302 kmsan_internal_poison_shadow+0xb1/0x1a0 mm/kmsan/kmsan.c:198 kmsan_kmalloc+0x7f/0xe0 mm/kmsan/kmsan.c:337 kmem_cache_alloc+0x1c2/0x1e0 mm/slub.c:2766 reqsk_alloc ./include/net/request_sock.h:87 inet_reqsk_alloc+0xa4/0x5b0 net/ipv4/tcp_input.c:6200 cookie_v6_check+0x4f4/0x1b50 net/ipv6/syncookies.c:169 tcp_v6_cookie_check net/ipv6/tcp_ipv6.c:989 tcp_v6_do_rcv+0xdd8/0x1c60 net/ipv6/tcp_ipv6.c:1298 tcp_v6_rcv+0x41a3/0x4f00 net/ipv6/tcp_ipv6.c:1487 ip6_input_finish+0x82f/0x1ee0 net/ipv6/ip6_input.c:279 NF_HOOK ./include/linux/netfilter.h:257 ip6_input+0x239/0x290 net/ipv6/ip6_input.c:322 dst_input ./include/net/dst.h:492 ip6_rcv_finish net/ipv6/ip6_input.c:69 NF_HOOK ./include/linux/netfilter.h:257 ipv6_rcv+0x1dbd/0x22e0 net/ipv6/ip6_input.c:203 __netif_receive_skb_core+0x2f6f/0x3a20 net/core/dev.c:4208 __netif_receive_skb net/core/dev.c:4246 process_backlog+0x667/0xba0 net/core/dev.c:4866 napi_poll net/core/dev.c:5268 net_rx_action+0xc95/0x1590 net/core/dev.c:5333 __do_softirq+0x485/0x942 kernel/softirq.c:284 ================================================================== Similar error is reported for cookie_v4_check(). Fixes: 58d607d3 ("tcp: provide skb->hash to synack packets") Signed-off-by:
Alexander Potapenko <glider@google.com> Acked-by:
-
Gao Feng authored
The global percpu variable ppp_xmit_recursion is used to detect the ppp xmit recursion to avoid the deadlock, which is caused by one CPU tries to lock the xmit lock twice. But it would report false recursion when one CPU wants to send the skb from two different PPP devices, like one L2TP on the PPPoE. It is a normal case actually. Now use one percpu member of struct ppp instead of the gloable variable to detect the xmit recursion of one ppp device. Fixes: 55454a56 ("ppp: avoid dealock on recursive xmit") Signed-off-by:
Gao Feng <gfree.wind@vip.163.com> Signed-off-by:
Liu Jianying <jianying.liu@ikuai8.com> Signed-off-by:
-
- 17 Jul, 2017 7 commits
-
-
WANG Cong authored
When req->rsk_listener is NULL, sk_to_full_sk() returns NULL too, so we have to check its return value against NULL here. Fixes: 40304b2a ("bpf: BPF support for sock_ops") Reported-by:
David Ahern <dsahern@gmail.com> Tested-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Jakub Kicinski authored
GCC 7 added a new -Wimplicit-fallthrough warning. It's only enabled with W=1, but since linux/jhash.h is included in over hundred places (including other global headers) it seems worthwhile fixing this warning. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
-
Florian Westphal authored
We crash in __nf_ct_expect_check, it calls nf_ct_remove_expect on the uninitialised expectation instead of existing one, so del_timer chokes on random memory address. Fixes: ec0e3f01 ("netfilter: nf_ct_expect: Add nf_ct_remove_expect()") Reported-by:
Sergey Kvachonok <ravenexp@gmail.com> Tested-by:
-
Florian Westphal authored
arp packets cannot be forwarded. They can be bridged, but then they can be filtered using either ebtables or nftables bridge family. The bridge netfilter exposes a "call-arptables" switch which pushes packets into arptables, but lets not expose this for nftables, so better close this asap. Signed-off-by:
-
Florian Westphal authored
When doing initial conversion to rhashtable I replaced the bucket walk with a single rhashtable_lookup_fast(). When moving to rhlist I failed to properly walk the list of identical tuples, but that is what is needed for this to work correctly. The table contains the original tuples, so the reply tuples are all distinct. We currently decide that mapping is (not) in range only based on the first entry, but in case its not we need to try the reply tuple of the next entry until we either find an in-range mapping or we checked all the entries. This bug makes nat core attempt collision resolution while it might be able to use the mapping as-is. Fixes: 870190a9 ("netfilter: nat: convert nat bysrc hash to rhashtable") Reported-by:
Jaco Kroon <jaco@uls.co.za> Tested-by:
-
Florian Westphal authored
no more users in the tree, remove this. The old api is racy wrt. module removal, all users have been converted to the netns-aware api. The old api pretended we still have global hooks but that has not been true for a long time. Signed-off-by:
-
Mateusz Jurczyk authored
Verify that the length of the socket buffer is sufficient to cover the nlmsghdr structure before accessing the nlh->nlmsg_len field for further input sanitization. If the client only supplies 1-3 bytes of data in sk_buff, then nlh->nlmsg_len remains partially uninitialized and contains leftover memory from the corresponding kernel allocation. Operating on such data may result in indeterminate evaluation of the nlmsg_len < NLMSG_HDRLEN expression. The bug was discovered by a runtime instrumentation designed to detect use of uninitialized memory in the kernel. The patch prevents this and other similar tools (e.g. KMSAN) from flagging this behavior in the future. Signed-off-by:
Mateusz Jurczyk <mjurczyk@google.com> Signed-off-by:
-
- 16 Jul, 2017 15 commits
-
-
David S. Miller authored
Doug Berger says: ==================== bcmgenet: Fragmented SKB corrections Two issues were observed in a review of the bcmgenet driver support for fragmented SKBs which are addressed by this patch set. The first addresses a problem that could occur if the driver is not able to DMA map a fragment of the SKB. This would be a highly unusual event but it would leave the hardware descriptors in an invalid state which should be prevented. The second is a hazard that could occur if the driver is able to reclaim the first control block of a fragmented SKB before all of its fragments have completed processing by the hardware. In this case the SKB could be freed leading to reuse of memory that is still in use by hardware. ==================== Signed-off-by: -
Doug Berger authored
Since the skb is attached to the first control block of a fragmented skb it is possible that the skb could be freed when reclaiming that control block before all fragments of the skb have been consumed by the hardware and unmapped. This commit introduces first_cb and last_cb pointers to the skb control block used by the driver to keep track of which transmit control blocks within a transmit ring are the first and last ones associated with the skb. It then splits the bcmgenet_free_cb() function into transmit (bcmgenet_free_tx_cb) and receive (bcmgenet_free_rx_cb) versions that can handle the unmapping of dma mapped memory and cleaning up the corresponding control block structure so that the skb is only freed after the last associated transmit control block is reclaimed. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
Doug Berger <opendmb@gmail.com> Signed-off-by:
-
Doug Berger authored
In case we fail to map a single fragment, we would be leaving the transmit ring populated with stale entries. This commit introduces the helper function bcmgenet_put_txcb() which takes care of rewinding the per-ring write pointer back to where we left. It also consolidates the functionality of bcmgenet_xmit_single() and bcmgenet_xmit_frag() into the bcmgenet_xmit() function to make the unmapping of control blocks cleaner. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Suggested-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Florian Fainelli authored
Commit 07d4510f ("dt-bindings: net: bgmac: add bindings documentation for bgmac") added both brcm,amac-nsp.txt and brcm,bgmac-nsp.txt. The former is actually the one that got updated and is in use by the bgmac driver while the latter is duplicating the former and is not used nor updated. Fixes: 07d4510f ("dt-bindings: net: bgmac: add bindings documentation for bgmac") Signed-off-by:
-
David S. Miller authored
Arvind Yadav says: ==================== Constify isdn pci_device_id's. pci_device_id are not supposed to change at runtime. All functions working with pci_device_id provided by <linux/pci.h> work with const pci_device_id. So mark the non-const structs as const. ==================== Signed-off-by: -
Arvind Yadav authored
pci_device_id are not supposed to change at runtime. All functions working with pci_device_id provided by <linux/pci.h> work with const pci_device_id. So mark the non-const structs as const. File size before: text data bss dec hex filename 11803 544 1 12348 303c isdn/hardware/avm/c4.o File size After adding 'const': text data bss dec hex filename 11931 416 1 12348 303c isdn/hardware/avm/c4.o Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by:
-
Arvind Yadav authored
pci_device_id are not supposed to change at runtime. All functions working with pci_device_id provided by <linux/pci.h> work with const pci_device_id. So mark the non-const structs as const. File size before: text data bss dec hex filename 21656 1024 96 22776 58f8 isdn/hardware/mISDN/hfcpci.o File size After adding 'const': text data bss dec hex filename 22424 256 96 22776 58f8 isdn/hardware/mISDN/hfcpci.o Signed-off-by:
-
Arvind Yadav authored
pci_device_id are not supposed to change at runtime. All functions working with pci_device_id provided by <linux/pci.h> work with const pci_device_id. So mark the non-const structs as const. File size before: text data bss dec hex filename 9963 1936 16 11915 2e8b isdn/hardware/mISDN/avmfritz.o File size After adding 'const': text data bss dec hex filename 10091 1808 16 11915 2e8b isdn/hardware/mISDN/avmfritz.o Signed-off-by:
-
Arvind Yadav authored
pci_device_id are not supposed to change at runtime. All functions working with pci_device_id provided by <linux/pci.h> work with const pci_device_id. So mark the non-const structs as const. File size before: text data bss dec hex filename 13959 4080 24 18063 468f isdn/hardware/mISDN/w6692.o File size After adding 'const': text data bss dec hex filename 14087 3952 24 18063 468f isdn/hardware/mISDN/w6692.o Signed-off-by:
-
Arvind Yadav authored
pci_device_id are not supposed to change at runtime. All functions working with pci_device_id provided by <linux/pci.h> work with const pci_device_id. So mark the non-const structs as const. File size before: text data bss dec hex filename 63450 1536 1492 66478 103ae isdn/hardware/mISDN/hfcmulti.o File size After adding 'const': text data bss dec hex filename 64698 288 1492 66478 103ae isdn/hardware/mISDN/hfcmulti.o Signed-off-by:
-
Arvind Yadav authored
pci_device_id are not supposed to change at runtime. All functions working with pci_device_id provided by <linux/pci.h> work with const pci_device_id. So mark the non-const structs as const. File size before: text data bss dec hex filename 10941 1776 16 12733 31bd isdn/hardware/mISDN/netjet.o File size After adding 'const': text data bss dec hex filename 11005 1712 16 12733 31bd isdn/hardware/mISDN/netjet.o Signed-off-by:
-
Arvind Yadav authored
pci_device_id are not supposed to change at runtime. All functions working with pci_device_id provided by <linux/pci.h> work with const pci_device_id. So mark the non-const structs as const. File size before: text data bss dec hex filename 6224 655 8 6887 1ae7 isdn/hardware/eicon/divasmain.o File size After adding 'const': text data bss dec hex filename 6608 271 8 6887 1ae7 isdn/hardware/eicon/divasmain.o Signed-off-by:
-
Arvind Yadav authored
pci_device_id are not supposed to change at runtime. All functions working with pci_device_id provided by <linux/pci.h> work with const pci_device_id. So mark the non-const structs as const. File size before: text data bss dec hex filename 5989 576 0 6565 19a5 isdn/hisax/hisax_fcpcipnp.o File size After adding 'const': text data bss dec hex filename 6085 480 0 6565 19a5 isdn/hisax/hisax_fcpcipnp.o Signed-off-by:
-
Arvind Yadav authored
pci_device_id are not supposed to change at runtime. All functions working with pci_device_id provided by <linux/pci.h> work with const pci_device_id. So mark the non-const structs as const. File size before: text data bss dec hex filename 10512 536 4 11052 2b2c drivers/isdn/hisax/hfc4s8s_l1.o File size After adding 'const': text data bss dec hex filename 10672 376 4 11052 2b2c drivers/isdn/hisax/hfc4s8s_l1.o Signed-off-by:
-
Arvind Yadav authored
pci_device_id are not supposed to change at runtime. All functions working with pci_device_id provided by <linux/pci.h> work with const pci_device_id. So mark the non-const structs as const. File size before: text data bss dec hex filename 13686 2064 4416 20166 4ec6 drivers/isdn/hisax/config.o File size After adding 'const': text data bss dec hex filename 15030 720 4416 20166 4ec6 drivers/isdn/hisax/config.o Signed-off-by:
-
- 15 Jul, 2017 7 commits
-
-
Neal Cardwell authored
Fixes the following behavior: for connections that had no RTT sample at the time of initializing congestion control, BBR was initializing the pacing rate to a high nominal rate (based an a guess of RTT=1ms, in case this is LAN traffic). Then BBR never adjusted the pacing rate downward upon obtaining an actual RTT sample, if the connection never filled the pipe (e.g. all sends were small app-limited writes()). This fix adjusts the pacing rate upon obtaining the first RTT sample. Fixes: 0f8782ea ("tcp_bbr: add BBR congestion control") Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
Neal Cardwell authored
Fix a corner case noticed by Eric Dumazet, where BBR's setting sk->sk_pacing_rate to 0 during initialization could theoretically cause packets in the sending host to hang if there were packets "in flight" in the pacing infrastructure at the time the BBR congestion control state is initialized. This could occur if the pacing infrastructure happened to race with bbr_init() in a way such that the pacer read the 0 rather than the immediately following non-zero pacing rate. Fixes: 0f8782ea ("tcp_bbr: add BBR congestion control") Reported-by:
-
Neal Cardwell authored
Introduce a helper to initialize the BBR pacing rate unconditionally, based on the current cwnd and RTT estimate. This is a pure refactor, but is needed for two following fixes. Fixes: 0f8782ea ("tcp_bbr: add BBR congestion control") Signed-off-by:
-
Neal Cardwell authored
Introduce a helper to convert a BBR bandwidth and gain factor to a pacing rate in bytes per second. This is a pure refactor, but is needed for two following fixes. Fixes: 0f8782ea ("tcp_bbr: add BBR congestion control") Signed-off-by:
-
Neal Cardwell authored
In bbr_set_pacing_rate(), which decides whether to cut the pacing rate, there was some code that considered exiting STARTUP to be equivalent to the notion of filling the pipe (i.e., bbr_full_bw_reached()). Specifically, as the code was structured, exiting STARTUP and going into PROBE_RTT could cause us to cut the pacing rate down to something silly and low, based on whatever bandwidth samples we've had so far, when it's possible that all of them have been small app-limited bandwidth samples that are not representative of the bandwidth available in the path. (The code was correct at the time it was written, but the state machine changed without this spot being adjusted correspondingly.) Fixes: 0f8782ea ("tcp_bbr: add BBR congestion control") Signed-off-by:
-
Greg Rose authored
When there is an established connection in direction A->B, it is possible to receive a packet on port B which then executes ct(commit,force) without first performing ct() - ie, a lookup. In this case, we would expect that this packet can delete the existing entry so that we can commit a connection with direction B->A. However, currently we only perform a check in skb_nfct_cached() for whether OVS_CS_F_TRACKED is set and OVS_CS_F_INVALID is not set, ie that a lookup previously occurred. In the above scenario, a lookup has not occurred but we should still be able to statelessly look up the existing entry and potentially delete the entry if it is in the opposite direction. This patch extends the check to also hint that if the action has the force flag set, then we will lookup the existing entry so that the force check at the end of skb_nfct_cached has the ability to delete the connection. Fixes: dd41d330b03 ("openvswitch: Add force commit.") CC: Pravin Shelar <pshelar@nicira.com> CC: dev@openvswitch.org Signed-off-by:Greg Rose <gvrose8192@gmail.com> Signed-off-by:
-
Alexander Potapenko authored
If the length field of the iterator (|pos.p| or |err|) is past the end of the chunk, we shouldn't access it. This bug has been detected by KMSAN. For the following pair of system calls: socket(PF_INET6, SOCK_STREAM, 0x84 /* IPPROTO_??? */) = 3 sendto(3, "A", 1, MSG_OOB, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = 1 the tool has reported a use of uninitialized memory: ================================================================== BUG: KMSAN: use of uninitialized memory in sctp_rcv+0x17b8/0x43b0 CPU: 1 PID: 2940 Comm: probe Not tainted 4.11.0-rc5+ #2926 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:16 dump_stack+0x172/0x1c0 lib/dump_stack.c:52 kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:927 __msan_warning_32+0x61/0xb0 mm/kmsan/kmsan_instr.c:469 __sctp_rcv_init_lookup net/sctp/input.c:1074 __sctp_rcv_lookup_harder net/sctp/input.c:1233 __sctp_rcv_lookup net/sctp/input.c:1255 sctp_rcv+0x17b8/0x43b0 net/sctp/input.c:170 sctp6_rcv+0x32/0x70 net/sctp/ipv6.c:984 ip6_input_finish+0x82f/0x1ee0 net/ipv6/ip6_input.c:279 NF_HOOK ./include/linux/netfilter.h:257 ip6_input+0x239/0x290 net/ipv6/ip6_input.c:322 dst_input ./include/net/dst.h:492 ip6_rcv_finish net/ipv6/ip6_input.c:69 NF_HOOK ./include/linux/netfilter.h:257 ipv6_rcv+0x1dbd/0x22e0 net/ipv6/ip6_input.c:203 __netif_receive_skb_core+0x2f6f/0x3a20 net/core/dev.c:4208 __netif_receive_skb net/core/dev.c:4246 process_backlog+0x667/0xba0 net/core/dev.c:4866 napi_poll net/core/dev.c:5268 net_rx_action+0xc95/0x1590 net/core/dev.c:5333 __do_softirq+0x485/0x942 kernel/softirq.c:284 do_softirq_own_stack+0x1c/0x30 arch/x86/entry/entry_64.S:902 </IRQ> do_softirq kernel/softirq.c:328 __local_bh_enable_ip+0x25b/0x290 kernel/softirq.c:181 local_bh_enable+0x37/0x40 ./include/linux/bottom_half.h:31 rcu_read_unlock_bh ./include/linux/rcupdate.h:931 ip6_finish_output2+0x19b2/0x1cf0 net/ipv6/ip6_output.c:124 ip6_finish_output+0x764/0x970 net/ipv6/ip6_output.c:149 NF_HOOK_COND ./include/linux/netfilter.h:246 ip6_output+0x456/0x520 net/ipv6/ip6_output.c:163 dst_output ./include/net/dst.h:486 NF_HOOK ./include/linux/netfilter.h:257 ip6_xmit+0x1841/0x1c00 net/ipv6/ip6_output.c:261 sctp_v6_xmit+0x3b7/0x470 net/sctp/ipv6.c:225 sctp_packet_transmit+0x38cb/0x3a20 net/sctp/output.c:632 sctp_outq_flush+0xeb3/0x46e0 net/sctp/outqueue.c:885 sctp_outq_uncork+0xb2/0xd0 net/sctp/outqueue.c:750 sctp_side_effects net/sctp/sm_sideeffect.c:1773 sctp_do_sm+0x6962/0x6ec0 net/sctp/sm_sideeffect.c:1147 sctp_primitive_ASSOCIATE+0x12c/0x160 net/sctp/primitive.c:88 sctp_sendmsg+0x43e5/0x4f90 net/sctp/socket.c:1954 inet_sendmsg+0x498/0x670 net/ipv4/af_inet.c:762 sock_sendmsg_nosec net/socket.c:633 sock_sendmsg net/socket.c:643 SYSC_sendto+0x608/0x710 net/socket.c:1696 SyS_sendto+0x8a/0xb0 net/socket.c:1664 do_syscall_64+0xe6/0x130 arch/x86/entry/common.c:285 entry_SYSCALL64_slow_path+0x25/0x25 arch/x86/entry/entry_64.S:246 RIP: 0033:0x401133 RSP: 002b:00007fff6d99cd38 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00000000004002b0 RCX: 0000000000401133 RDX: 0000000000000001 RSI: 0000000000494088 RDI: 0000000000000003 RBP: 00007fff6d99cd90 R08: 00007fff6d99cd50 R09: 000000000000001c R10: 0000000000000001 R11: 0000000000000246 R12: 0000000000000000 R13: 00000000004063d0 R14: 0000000000406460 R15: 0000000000000000 origin: save_stack_trace+0x37/0x40 arch/x86/kernel/stacktrace.c:59 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:302 kmsan_internal_poison_shadow+0xb1/0x1a0 mm/kmsan/kmsan.c:198 kmsan_poison_shadow+0x6d/0xc0 mm/kmsan/kmsan.c:211 slab_alloc_node mm/slub.c:2743 __kmalloc_node_track_caller+0x200/0x360 mm/slub.c:4351 __kmalloc_reserve net/core/skbuff.c:138 __alloc_skb+0x26b/0x840 net/core/skbuff.c:231 alloc_skb ./include/linux/skbuff.h:933 sctp_packet_transmit+0x31e/0x3a20 net/sctp/output.c:570 sctp_outq_flush+0xeb3/0x46e0 net/sctp/outqueue.c:885 sctp_outq_uncork+0xb2/0xd0 net/sctp/outqueue.c:750 sctp_side_effects net/sctp/sm_sideeffect.c:1773 sctp_do_sm+0x6962/0x6ec0 net/sctp/sm_sideeffect.c:1147 sctp_primitive_ASSOCIATE+0x12c/0x160 net/sctp/primitive.c:88 sctp_sendmsg+0x43e5/0x4f90 net/sctp/socket.c:1954 inet_sendmsg+0x498/0x670 net/ipv4/af_inet.c:762 sock_sendmsg_nosec net/socket.c:633 sock_sendmsg net/socket.c:643 SYSC_sendto+0x608/0x710 net/socket.c:1696 SyS_sendto+0x8a/0xb0 net/socket.c:1664 do_syscall_64+0xe6/0x130 arch/x86/entry/common.c:285 return_from_SYSCALL_64+0x0/0x6a arch/x86/entry/entry_64.S:246 ================================================================== Signed-off-by:
-
