Skip to content

L
linux
Switch branch/tag
  1. 10 Aug, 2018 1 commit
    • Maarten Lankhorst's avatar
      drm/i915: Allow control of PSR at runtime through debugfs, v6 · c44301fc
      Maarten Lankhorst authored 
      Currently tests modify i915.enable_psr and then do a modeset cycle
to change PSR. We can write a value to i915_edp_psr_debug to force
a certain PSR mode without a modeset.

To retain compatibility with older userspace, we also still allow
the override through the module parameter, and add some tracking
to check whether a debugfs mode is specified.

Changes since v1:
- Rename dev_priv->psr.enabled to .dp, and .hw_configured to .enabled.
- Fix i915_psr_debugfs_mode to match the writes to debugfs.
- Rename __i915_edp_psr_write to intel_psr_set_debugfs_mode, simplify
  it and move it to intel_psr.c. This keeps all internals in intel_psr.c
- Perform an interruptible wait for hw completion outside of the psr
  lock, instead of being forced to trywait and return -EBUSY.
Changes since v2:
- Rebase on top of intel_psr changes.
Changes since v3:
- Assign psr.dp during init. (dhnkrn)
- Add prepared bool, which should be used instead of relying on psr.dp. (dhnkrn)
- Fix -EDEADLK handling in debugfs. (dhnkrn)
- Clean up waiting for idle in intel_psr_set_debugfs_mode.
- Print PSR mode when trying to enable PSR. (dhnkrn)
- Move changing psr debug setting to i915_edp_psr_debug_set. (dhnkrn)
Changes since v4:
- Return error in _set() function.
- Change flag values to make them easier to remember. (dhnkrn)
- Only assign psr.dp once. (dhnkrn)
- Only set crtc_state->has_psr on the crtc with psr.dp.
- Fix typo. (dhnkrn)
Changes since v5:
- Only wait for PSR idle on the PSR connector correctly. (dhnkrn)
- Reinstate WARN_ON(drrs.dp) in intel_psr_enable. (dhnkrn)
- Remove stray comment. (dhnkrn)
- Be silent in intel_psr_compute_config on wrong connector. (dhnkrn)
Signed-off-by: default avatarMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180809142101.26155-1-maarten.lankhorst@linux.intel.comReviewed-by: default avatarDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
      c44301fc
  3. 09 Aug, 2018 3 commits
  5. 08 Aug, 2018 13 commits
  7. 07 Aug, 2018 3 commits
  9. 06 Aug, 2018 4 commits
  11. 03 Aug, 2018 4 commits
  13. 02 Aug, 2018 2 commits
  15. 01 Aug, 2018 3 commits
  17. 31 Jul, 2018 1 commit
    • Chris Wilson's avatar
      drm/i915: Interactive RPS mode · 60548c55
      Chris Wilson authored 
      RPS provides a feedback loop where we use the load during the previous
evaluation interval to decide whether to up or down clock the GPU
frequency. Our responsiveness is split into 3 regimes, a high and low
plateau with the intent to keep the gpu clocked high to cover occasional
stalls under high load, and low despite occasional glitches under steady
low load, and inbetween. However, we run into situations like kodi where
we want to stay at low power (video decoding is done efficiently
inside the fixed function HW and doesn't need high clocks even for high
bitrate streams), but just occasionally the pipeline is more complex
than a video decode and we need a smidgen of extra GPU power to present
on time. In the high power regime, we sample at sub frame intervals with
a bias to upclocking, and conversely at low power we sample over a few
frames worth to provide what we consider to be the right levels of
responsiveness respectively. At low power, we more or less expect to be
kicked out to high power at the start of a busy sequence by waitboosting.

Prior to commit e9af4ea2 ("drm/i915: Avoid waitboosting on the active
request") whenever we missed the frame or stalled, we would immediate go
full throttle and upclock the GPU to max. But in commit e9af4ea2, we
relaxed the waitboosting to only apply if the pipeline was deep to avoid
over-committing resources for a near miss. Sadly though, a near miss is
still a miss, and perceptible as jitter in the frame delivery.

To try and prevent the near miss before having to resort to boosting
after the fact, we use the pageflip queue as an indication that we are
in an "interactive" regime and so should sample the load more frequently
to provide power before the frame misses it vblank. This will make us
more favorable to providing a small power increase (one or two bins) as
required rather than going all the way to maximum and then having to
work back down again. (We still keep the waitboosting mechanism around
just in case a dramatic change in system load requires urgent uplocking,
faster than we can provide in a few evaluation intervals.)

v2: Reduce rps_set_interactive to a boolean parameter to avoid the
confusion of what if they wanted a new power mode after pinning to a
different mode (which to choose?)
v3: Only reprogram RPS while the GT is awake, it will be set when we
wake the GT, and while off warns about being used outside of rpm.
v4: Fix deferred application of interactive mode
v5: s/state/interactive/
v6: Group the mutex with its principle in a substruct

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107111
Fixes: e9af4ea2 ("drm/i915: Avoid waitboosting on the active request")
Signed-off-by: default avatarChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: default avatarJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180731132629.3381-1-chris@chris-wilson.co.uk
      60548c55
  19. 30 Jul, 2018 4 commits
  21. 27 Jul, 2018 2 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7