92eba04e
(ASoC: rcar: remove RSND_SSI_CLK_FROM_ADG) removed
RSND_SSI_CLK_FROM_ADG, it is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

FSI address size is 0x400, not 0x8400
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Only the SH-Mobile product name is mentioned in the Kconfig descriptions
and help texts. This makes it difficult for external engineers working
on other Renesas platforms to find upstream platform support as the
combination of the SH-Mobile name and using the product number proved an
effective method of concealment.

Replace the "SH-Mobile" name with "Renesas ARM SoCs" in all the related
descriptions, help texts and comments.
Reported-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The USB0 and USB1 VBUS pins must be pulled down. Add corresponding
configuration entries in the pinctrl map table instead of manually
poking the pin control registers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch enables Spansion S25FL512SAGMFIG11 chip on QSPI,
Add support for the QSPI interface on Lager.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Treat both negative and zero return values from clk_round_rate() as
errors.  This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather than a
signed type, since some clock sources can generate rates higher than
(2^31)-1 Hz.

Eventually, when calling clk_round_rate(), only a return value of zero
will be considered a error.  All other values will be considered valid
rates.  The comparison against values less than 0 is kept to preserve
the correct behavior in the meantime.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add code to setup the r8a7791 PFC for the Koelsch board.

At this point serial consoles are added, and in the near
future other platform-device-only devices will be added
here like for instance the r8a7791 DU.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Hook in shmobile_init_late() on Lager V2. This enables some PM
related things like CPUIdle and Suspend-to-RAM.

With this patch applied it is possible to use Suspend-to-RAM:
# echo enabled > /sys/class/tty/ttySC6/power/wakeup
# echo mem > /sys/power/state
(wake by sending a character on the serial console)
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add support for Koelsch SW30-SW36 using GPIO keys.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable wakeup for the GPIO keys on the Koelsch board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Hook in shmobile_init_late() on Koelsch. This enables some PM
related things like CPUIdle and Suspend-to-RAM.

With this patch applied it is possible to use Suspend-to-RAM:
# echo enabled > /sys/class/tty/ttySC6/power/wakeup
# echo mem > /sys/power/state
(wake by sending a character on the serial console)
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable wakeup for the GPIO keys on the Lager board.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add r7s72100 Genmai to SHMOBILE_MULTI.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add C code support for r7s72100 Genmai DT reference.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the DT bits for r7s72100 Genmai DT reference support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add Koelsch and r8a7791 to CONFIG_SHMOBILE_MULTI. At this
point CCF is not yet supported so you cannot run this code
yet. For CCF support to happen several different components
are needed, and this is one simple portion that moves us
forward. Other patches need to build on top of this one.

Koelsch board support exists in 3 flavors:
1) SHMOBILE_MULTI, MACH_KOELSCH - board-koelsch-reference.c (CCF + DT)
2) SHMOBILE, MACH_KOELSCH_REFERENCE - board-koelsch-reference.c (DT)
3) SHMOBILE, MACH_KOELSCH - board-koelsch.c (legacy C code)

When CCF is done then 2) will be removed. When 1) includes same features
as 3) then 3) will be removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

In R-Car GPIO hardware block, 'chattering removal' feature can be
enabled on GPIO-n-[3:0] pins, but it's not supported on rest of pins
GPIO-n-[31:4].

Set an appropriate debounce interval, instead.  We could confirm that
spurious/unnecessary GPIO interrupts are prevented by this settings.

Based on work for the lager board by Shinya Kuribayashi.

Cc: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

In R-Car GPIO hardware block, 'chattering removal' feature can be
enabled on GPIO-n-[3:0] pins, but it's not supported on rest of pins
GPIO-n-[31:4].

Set an appropriate debounce interval, instead.  We could confirm that
spurious/unnecessary GPIO interrupts are prevented by this settings.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

SDHI CD/WP pin needs pull-up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Don't keep FPGA ioremap area.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add DT reference support for the r8a7791 Koelsch board.

This board support file will be used together with common
clocks and multiplatform in the future.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable Koelsch GPIO switch for GPIO input and IRQ testing purpose.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable Koelsch LEDs for GPIO output testing purpose.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable r8a7791 PFC and GPIO on the Koelsch board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

When regulators are used with MMC devices, sh_mmcif_plat_data::ocr
is not needed, they can be removed from platform data.
This patch adds v3.3 regulator settings,
and moved fixed-dummy regulator registration position
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Renesas ARM based SoC cleanups for v3.14

* Tidy up clock table order for r7s72100, r8a7779, r8a7779, r8a7790,
  sh7372 and sh73a0 SoCs.
* Tidy up camera-rcar header for r8a7779 SoC
* Tidy up registration of VIN on r8a7779 SoC
* Tidy up PFC registration on r8a7790 SoC
* Correct typo in clocks for r8a7790 SoC
* Don't use named resources for IPMMU, I2C and TMU on sh73a0 SoC
* Don't use named resources for MMCIF and SDHI on ape6evm board
* Don't use named resources for MMCIF on lager board
* Tidy up device registration on lager board
* Tidy up headers for bockw board

Based on work for the r8a7778 SoC by Kuninori Morimoto.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Since ("ARM: shmobile: Remove legacy KZM9D board code")
It is now necessary for AUTO_ZRELADDR to be selected
in order for the kernel to build with kzm9d_defconfig.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

SuperH lookups clock is using CLKDEV_CON/DEV/ICK_ID() macro
for a long term.
But in these days, the ICK clock is defined in random place.
This patch arranges it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

I2C clock is based on P clock, not HP clock
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

EXTAL clock frequency needs 1/2 when
(MD14, MD13, MD19) = (1, x, x).
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the r8a7791 thermal device as legacy clocks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a thermal platform device for the legacy case
on the r8a7791 SoC. This keeps the r8a7791 in sync
with the r8a7790 sister device.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the r8a7790 DT thermal device to the legacy clocks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

SH-Mobile platforms are transitioning from non-multiplatform to
multiplatform kernel. A new ARCH_SHMOBILE_MULTI configuration symbol has
been created to group all multiplatform-enabled SH-Mobile SoCs. The
existing ARCH_SHMOBILE configuration symbol groups SoCs that haven't
been converted yet.

This arrangement works fine for the arch/ code, but lots of drivers
needed on both ARCH_SHMOBILE and ARCH_SHMOBILE_MULTI depend on
ARCH_SHMOBILE only. In order to avoid changing them, rename
ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY, and create a new boolean
ARCH_SHMOBILE configuration symbol that is selected by both
ARCH_SHMOBILE_LEGACY and ARCH_SHMOBILE_MULTI.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The ZX parent clock isn't implemented yet, add it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Now when the legacy KZM9D board code is gone, make sure
USE_OF is selected in case of the EMEV2 SoC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>