- 23 Apr, 2020 4 commits
-
-
Chuah, Kim Tatt authored
For dwmac4, enable VLAN promiscuity when MAC controller is requested to enter promiscuous mode. Signed-off-by:
Chuah, Kim Tatt <kim.tatt.chuah@intel.com> Signed-off-by:
Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by:
Tan, Tee Min <tee.min.tan@intel.com> Signed-off-by:
Wong Vee Khee <vee.khee.wong@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Wei Yongjun authored
macvlan_hash_lookup() uses list_for_each_entry_rcu() for traversing should either under RCU in fast path or the protection of rtnl_mutex. In the case of holding RTNL, we should add the corresponding lockdep expression to silence the following false-positive warning: ============================= WARNING: suspicious RCU usage 5.7.0-rc1-next-20200416-00003-ga3b8d28bc #1 Not tainted ----------------------------- drivers/net/macvlan.c:126 RCU-list traversed in non-reader section!! Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David Ahern authored
Add tests for vrf and xfrms with a second round after adding a qdisc. There are a few known problems documented with the test cases that fail. The fix is non-trivial; will come back to it when time allows. Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Xiaoliang Yang authored
Right now it can be seen that the VSC9959 (Felix) switch will not flood frames if they have a VLAN tag with a PCP of 1-7 (nonzero). It turns out that Felix is quite different from its cousin, Ocelot, in that frame flooding can be allowed/denied per traffic class. Where Ocelot has 1 instance of the ANA_FLOODING register, Felix has 8. The approach that this driver is going to take is "thanks, but no thanks". We have no use case of limiting the flooding domain based on traffic class, so we just want to allow packets to be flooded, no matter what traffic class they have. So we copy the line of code from ocelot.c which does the one-shot initialization of the flooding PGIDs, and we add it to felix.c as well - except replicated 8 times. Signed-off-by:
Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 22 Apr, 2020 17 commits
-
-
Manivannan Sadhasivam authored
Add tracepoint support for QRTR with NS as the first candidate. Later on this can be extended to core QRTR and transport drivers. The trace_printk() used in NS has been replaced by tracepoints. Signed-off-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
YueHaibing authored
net/ipv6/ila/ila_xlat.c:604:0: warning: macro "ILA_HASH_TABLE_SIZE" is not used [-Wunused-macros] Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
wenxu authored
When the act_ct SW offload in flowtable, The counter of the conntrack entry will never update. So update the nf_conn_acct conuter in act_ct flowtable software offload. Signed-off-by:
wenxu <wenxu@ucloud.cn> Reviewed-by:
Roi Dayan <roid@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Heiner Kallweit says: ==================== net: phy: add device-managed devm_mdiobus_register If there's no special ordering requirement for mdiobus_unregister(), then driver code can be simplified by using a device-managed version of mdiobus_register(). Prerequisite is that bus allocation has been done device-managed too. Else mdiobus_free() may be called whilst bus is still registered, resulting in a BUG_ON(). Therefore let devm_mdiobus_register() return -EPERM if bus was allocated non-managed. First user of the new functionality is r8169 driver. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Use new function devm_mdiobus_register() to simplify the driver. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
If there's no special ordering requirement for mdiobus_unregister(), then driver code can be simplified by using a device-managed version of mdiobus_register(). Prerequisite is that bus allocation has been done device-managed too. Else mdiobus_free() may be called whilst bus is still registered, resulting in a BUG_ON(). Therefore let devm_mdiobus_register() return -EPERM if bus was allocated non-managed. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Michael Walle authored
The PHY supports monitoring its die temperature as well as two analog voltages. Add support for it. Signed-off-by:
Michael Walle <michael@walle.cc> Acked-by:
Guenter Roeck <linux@roeck-us.net> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Michael Walle authored
The Broadcom BCM54140 is a Quad SGMII/QSGMII Copper/Fiber Gigabit Ethernet transceiver. This also adds support for tunables to set and get downshift and energy detect auto power-down. The PHY has four ports and each port has its own PHY address. There are per-port registers as well as global registers. Unfortunately, the global registers can only be accessed by reading and writing from/to the PHY address of the first port. Further, there is no way to find out what port you actually are by just reading the per-port registers. We therefore, have to scan the bus on the PHY probe to determine the port and thus what address we need to access the global registers. Signed-off-by:
Michael Walle <michael@walle.cc> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Michael Walle authored
RDB (Register Data Base) registers are used on newer Broadcom PHYs. Add helper to read, write and modify these registers. Signed-off-by:
Michael Walle <michael@walle.cc> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Florian Fainelli says: ==================== dt-bindings: net: mdio.yaml fixes This patch series documents some common MDIO devices properties such as resets (and delays) and broken-turn-around. The second patch also rephrases some descriptions to be more general towards MDIO devices and not specific towards Ethernet PHYs. Changes in v3: - corrected wording of 'broken-turn-around' in ethernet-phy.yaml and mdio.yaml, add Andrew's R-b tag to patch #3 ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
A number of descriptions assume a PHY device, but since this binding describes a MDIO bus which can have different kinds of MDIO devices attached to it, rephrase some descriptions to be more general in that regard. Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
Some of the properties pertaining to the broken turn around or resets were only documented in ethernet-phy.yaml while they are applicable across all MDIO devices and not Ethernet PHYs specifically which are a superset. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
The turn around bytes (2) are placed between the control phase of the MDIO transaction and the data phase, correct the wording to be more exact. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Vladimir Oltean says: ==================== Ocelot MAC_ETYPE tc-flower key improvements As discussed in the comments surrounding this patch: https://patchwork.ozlabs.org/project/netdev/patch/20200417190308.32598-1-olteanv@gmail.com/ the restrictions imposed on non-MAC_ETYPE rules were harsher than they needed to be. IP, IPv6, ARP rules can still be added concurrently with src_mac and dst_mac rules, as long as those MAC address rules do not ask for an offending EtherType. For that to actually be supported, we need to parse the EtherType from the flower classification rule first. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
An attempt was made in commit fe3490e6 ("net: mscc: ocelot: Hardware ofload for tc flower filter") to avoid clashes between MAC_ETYPE rules and IP rules. Because the protocol blacklist should have included ETH_P_ALL too, it created some confusion, but now the situation should be dealt with a bit better by the patch immediately previous to this one ("net: mscc: ocelot: refine the ocelot_ace_is_problematic_mac_etype function"). So now we can remove that check. MAC_ETYPE rules with a protocol of ETH_P_IP, ETH_P_IPV6, ETH_P_ARP and ETH_P_ALL _are_ supported, with some restrictions regarding per-port exclusivity which are enforced now. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
The commit mentioned below was a bit too harsh, and while it restricted the invalid key combinations which are known to not work, such as: tc filter add dev swp0 ingress proto ip \ flower src_ip 192.0.2.1 action drop tc filter add dev swp0 ingress proto all \ flower src_mac 00:11:22:33:44:55 action drop it also restricted some which still should work, such as: tc filter add dev swp0 ingress proto ip \ flower src_ip 192.0.2.1 action drop tc filter add dev swp0 ingress proto 0x22f0 \ flower src_mac 00:11:22:33:44:55 action drop What actually does not match "sanely" is a MAC_ETYPE rule on frames having an EtherType of ARP, IPv4, IPv6, in addition to SNAP and OAM frames (which the ocelot tc-flower implementation does not parse yet, so the function might need to be revisited again in the future). So just make the function recognize the problematic MAC_ETYPE rules by EtherType - thus the VCAP IS2 can be forced to match even on those packets. This patch makes it possible for IP rules to live on a port together with MAC_ETYPE rules that are non-all, non-arp, non-ip and non-ipv6. Fixes: d4d0cb741d7b ("net: mscc: ocelot: deal with problematic MAC_ETYPE VCAP IS2 rules") Reported-by:
Allan W. Nielsen <allan.nielsen@microchip.com> Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
Currently, the filter's protocol is ignored except for a few special cases (IPv4 and IPv6). The EtherType can be matched inside VCAP IS2 by using a MAC_ETYPE key. So there are 2 cases in which EtherType matches are supported: - As part of a larger MAC_ETYPE rule, such as: tc filter add dev swp0 ingress protocol ip \ flower skip_sw src_mac 42:be:24:9b:76:20 action drop - Standalone (matching on protocol only): tc filter add dev swp0 ingress protocol arp \ flower skip_sw action drop As before, if the protocol is not specified, is it implicitly "all" and the EtherType mask in the MAC_ETYPE half key is set to zero. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 21 Apr, 2020 13 commits
-
-
David S. Miller authored
Yangbo Lu says: ==================== Support programmable pins for Ocelot PTP driver The Ocelot PTP clock driver had been embedded into ocelot.c driver. It had supported basic gettime64/settime64/adjtime/adjfine functions by now which were used by both Ocelot switch and Felix switch. This patch-set is to move current ptp clock code out of ocelot.c driver maintaining as a single ocelot_ptp.c driver, and to implement 4 programmable pins with only PTP_PF_PEROUT function for now. The PTP_PF_EXTTS function will be supported in the future, and it should be implemented separately for Felix and Ocelot, because of different hardware interrupt implementation in them. Changes for v2: - Put PTP driver under drivers/net/ethernet/mscc/. - Dropped MAINTAINERS patch. Kept original maintaining. - Initialized PTP separately in ocelot/felix platforms. - Supported PPS case in programmable pin. - Supported disabling pin function since deadlock is fixed by Richard. - Returned -EBUSY if not finding pin available. Changes for v3: - Re-sent. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yangbo Lu authored
Enable PTP programmable pin. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yangbo Lu authored
Enable PTP programmable pin. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yangbo Lu authored
Support 4 PTP programmable pins with only PTP_PF_PEROUT function for now. The PTP_PF_EXTTS function will be supported in the future, and it should be implemented separately for Felix and Ocelot, because of different hardware interrupt implementation in them. Since the hardware is not able to support absolute start time, the periodic clock request only allows start time 0 0. But nsec could be accepted for PPS case for phase adjustment. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yangbo Lu authored
Add wave programming registers definitions for Ocelot platforms. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yangbo Lu authored
There are 5 PTP_PINS register groups on Ocelot switch. Except the one used for TOD operations, there are still 4 register groups for programmable pins. So redefine the 4 programmable pins. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yangbo Lu authored
The timestamp info should be only software timestamp capabilities if ptp clock does not work. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yangbo Lu authored
The Ocelot PTP clock driver had been embedded into ocelot.c driver. It had supported basic gettime64/settime64/adjtime/adjfine functions by now which were used by both Ocelot switch and Felix switch. This patch is to move current ptp clock code out of ocelot.c driver maintaining as a single ocelot_ptp.c. For futher new features implementation, the common code could be put in ocelot_ptp.c and the switch specific code should be in specific switch driver. The interrupt implementation in SoC is different between Ocelot and Felix. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Leon Romanovsky says: ==================== Remove vermagic header from global include folder Changelog: v2: * Changed the implementation of patch #4 to be like Masahiro wants. I personally don't like this implementation and changing it just to move forward this this patchset. v1: https://lore.kernel.org/lkml/20200415133648.1306956-1-leon@kernel.org * Added tags * Updated patch #4 with test results * Changed scripts/mod/modpost.c to create inclusion of vermagic.h from kernel folder and not from general include/linux. This is needed to generate *.mod.c files, while building modules. v0: https://lore.kernel.org/lkml/20200414155732.1236944-1-leon@kernel.org This is followup to the failure reported by Borislav [1] and suggested fix later on [2]. The series removes all includes of linux/vermagic.h, updates hns and nfp to use same kernel versioning scheme (exactly like we did for other drivers in previous cycle) and removes vermagic.h from global include folder. [1] https://lore.kernel.org/lkml/20200411155623.GA22175@zn.tnic [2] https://lore.kernel.org/lkml/20200413080452.GA3772@zn.tnic ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Leon Romanovsky authored
VERMAGIC* definitions are not supposed to be used by the drivers, see this [1] bug report, so introduce special define to guard inclusion of this header file and define it in kernel/modules.h and in internal script that generates *.mod.c files. In-tree module build: ➜ kernel git:(vermagic) ✗ make clean ➜ kernel git:(vermagic) ✗ make M=drivers/infiniband/hw/mlx5 ➜ kernel git:(vermagic) ✗ modinfo drivers/infiniband/hw/mlx5/mlx5_ib.ko filename: /images/leonro/src/kernel/drivers/infiniband/hw/mlx5/mlx5_ib.ko <...> vermagic: 5.6.0+ SMP mod_unload modversions Out-of-tree module build: ➜ mlx5 make -C /images/leonro/src/kernel clean M=/tmp/mlx5 ➜ mlx5 make -C /images/leonro/src/kernel M=/tmp/mlx5 ➜ mlx5 modinfo /tmp/mlx5/mlx5_ib.ko filename: /tmp/mlx5/mlx5_ib.ko <...> vermagic: 5.6.0+ SMP mod_unload modversions [1] https://lore.kernel.org/lkml/20200411155623.GA22175@zn.tnicReported-by:
Borislav Petkov <bp@suse.de> Acked-by:
Borislav Petkov <bp@suse.de> Acked-by:
Jessica Yu <jeyu@kernel.org> Co-developed-by:
Masahiro Yamada <masahiroy@kernel.org> Signed-off-by:
Masahiro Yamada <masahiroy@kernel.org> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Leon Romanovsky authored
Change nfp driver to use globally defined kernel version. Reported-by:
Borislav Petkov <bp@suse.de> Acked-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Reviewed-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Leon Romanovsky authored
Use globally defined kernel version instead of custom driver variant. Reported-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Leon Romanovsky authored
Get rid of linux/vermagic.h includes, so that MODULE_ARCH_VERMAGIC from the arch header arch/x86/include/asm/module.h won't be redefined. In file included from ./include/linux/module.h:30, from drivers/net/ethernet/3com/3c515.c:56: ./arch/x86/include/asm/module.h:73: warning: "MODULE_ARCH_VERMAGIC" redefined 73 | # define MODULE_ARCH_VERMAGIC MODULE_PROC_FAMILY | In file included from drivers/net/ethernet/3com/3c515.c:25: ./include/linux/vermagic.h:28: note: this is the location of the previous definition 28 | #define MODULE_ARCH_VERMAGIC "" | Fixes: 6bba2e89 ("net/3com: Delete driver and module versions from 3com drivers") Co-developed-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
Borislav Petkov <bp@suse.de> Acked-by: Shannon Nelson <snelson@pensando.io> # ionic Acked-by: Sebastian Reichel <sre@kernel.org> # power Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 20 Apr, 2020 6 commits
-
-
Colin Ian King authored
The variable rc is being assigned with a value that is never read and it is being updated later with a new value. The initialization is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Andy Shevchenko says: ==================== net: bcmgenet: Clean up after ACPI enablement ACPI enablement series had missed some clean ups that would have been done at the same time. Here are these bits. In v2: - return dev_dbg() calls to avoid spamming logs when probe is deferred (Florian) - added Ack (Florian) - combined two, earlier sent, series together - added couple more patches ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andy Shevchenko authored
No need to have parentheses around plain pointer variable or negation operator. Drop them for good. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andy Shevchenko authored
It's convenient to use get_unligned_beXX() and put_unaligned_beXX() helpers to get or set MAC instead of open-coded variants. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andy Shevchenko authored
Conversion to devm_clk_get_optional() makes it explicit that clocks are optional. This change allows to handle deferred probe in case clocks are defined, but not yet probed. Due to above changes bail out in error case. While here, check potential error when enable main clock. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andy Shevchenko authored
There is nothing which needs a set of OF headers, followed by redundant OF node ID check. Drop them for good. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-