1. 30 May, 2019 7 commits
    • Ioana Ciornei's avatar
      net: phy: Add phy_standalone sysfs entry · c920f745
      Ioana Ciornei authored
      Export a phy_standalone device attribute that is meant to give the
      indication that this PHY lacks an attached_dev and its corresponding
      sysfs link. The attribute will be created only when the
      phy_attach_direct() function will be called with a NULL net_device.
      Signed-off-by: default avatarIoana Ciornei <ioana.ciornei@nxp.com>
      Reviewed-by: default avatarFlorian Fainelli <f.fainelli@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      c920f745
    • Ioana Ciornei's avatar
      net: phy: Check against net_device being NULL · 82c76aca
      Ioana Ciornei authored
      In general, we don't want MAC drivers calling phy_attach_direct with the
      net_device being NULL. Add checks against this in all the functions
      calling it: phy_attach() and phy_connect_direct().
      Signed-off-by: default avatarIoana Ciornei <ioana.ciornei@nxp.com>
      Suggested-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Reviewed-by: default avatarFlorian Fainelli <f.fainelli@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      82c76aca
    • Ioana Ciornei's avatar
      net: phy: Guard against the presence of a netdev · 2db2d9d1
      Ioana Ciornei authored
      A prerequisite for PHYLIB to work in the absence of a struct net_device
      is to not access pointers to it.
      
      Changes are needed in the following areas:
      
       - Printing: In some places netdev_err was replaced with phydev_err.
      
       - Incrementing reference count to the parent MDIO bus driver: If there
         is no net device, then the reference count should definitely be
         incremented since there is no chance that it was an Ethernet driver
         who registered the MDIO bus.
      
       - Sysfs links are not created in case there is no attached_dev.
      
       - No netif_carrier_off is done if there is no attached_dev.
      Signed-off-by: default avatarIoana Ciornei <ioana.ciornei@nxp.com>
      Signed-off-by: default avatarVladimir Oltean <olteanv@gmail.com>
      Reviewed-by: default avatarFlorian Fainelli <f.fainelli@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2db2d9d1
    • Vladimir Oltean's avatar
      net: phy: Add phy_sysfs_create_links helper function · 53cfca2d
      Vladimir Oltean authored
      This is a cosmetic patch that wraps the operation of creating sysfs
      links between the netdev->phydev and the phydev->attached_dev.
      
      This is needed to keep the indentation level in check in a follow-up
      patch where this function will be guarded against the existence of a
      phydev->attached_dev.
      Signed-off-by: default avatarVladimir Oltean <olteanv@gmail.com>
      Signed-off-by: default avatarIoana Ciornei <ioana.ciornei@nxp.com>
      Reviewed-by: default avatarFlorian Fainelli <f.fainelli@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      53cfca2d
    • Kevin 'ldir' Darbyshire-Bryant's avatar
      net: sched: Introduce act_ctinfo action · 24ec483c
      Kevin 'ldir' Darbyshire-Bryant authored
      ctinfo is a new tc filter action module.  It is designed to restore
      information contained in firewall conntrack marks to other packet fields
      and is typically used on packet ingress paths.  At present it has two
      independent sub-functions or operating modes, DSCP restoration mode &
      skb mark restoration mode.
      
      The DSCP restore mode:
      
      This mode copies DSCP values that have been placed in the firewall
      conntrack mark back into the IPv4/v6 diffserv fields of relevant
      packets.
      
      The DSCP restoration is intended for use and has been found useful for
      restoring ingress classifications based on egress classifications across
      links that bleach or otherwise change DSCP, typically home ISP Internet
      links.  Restoring DSCP on ingress on the WAN link allows qdiscs such as
      but by no means limited to CAKE to shape inbound packets according to
      policies that are easier to set & mark on egress.
      
      Ingress classification is traditionally a challenging task since
      iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
      lookups, hence are unable to see internal IPv4 addresses as used on the
      typical home masquerading gateway.  Thus marking the connection in some
      manner on egress for later restoration of classification on ingress is
      easier to implement.
      
      Parameters related to DSCP restore mode:
      
      dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
      conntrack mark field contain the DSCP value to be restored.
      
      statemask - a 32 bit mask of (usually) 1 bit length, outside the area
      specified by dscpmask.  This represents a conditional operation flag
      whereby the DSCP is only restored if the flag is set.  This is useful to
      implement a 'one shot' iptables based classification where the
      'complicated' iptables rules are only run once to classify the
      connection on initial (egress) packet and subsequent packets are all
      marked/restored with the same DSCP.  A mask of zero disables the
      conditional behaviour ie. the conntrack mark DSCP bits are always
      restored to the ip diffserv field (assuming the conntrack entry is found
      & the skb is an ipv4/ipv6 type)
      
      e.g. dscpmask 0xfc000000 statemask 0x01000000
      
      |----0xFC----conntrack mark----000000---|
      | Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
      | DSCP       | unused | flag  |unused   |
      |-----------------------0x01---000000---|
            |                   |
            |                   |
            ---|             Conditional flag
               v             only restore if set
      |-ip diffserv-|
      | 6 bits      |
      |-------------|
      
      The skb mark restore mode (cpmark):
      
      This mode copies the firewall conntrack mark to the skb's mark field.
      It is completely the functional equivalent of the existing act_connmark
      action with the additional feature of being able to apply a mask to the
      restored value.
      
      Parameters related to skb mark restore mode:
      
      mask - a 32 bit mask applied to the firewall conntrack mark to mask out
      bits unwanted for restoration.  This can be useful where the conntrack
      mark is being used for different purposes by different applications.  If
      not specified and by default the whole mark field is copied (i.e.
      default mask of 0xffffffff)
      
      e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
      aforementioned DSCP restore mode.
      
      |----0x00----conntrack mark----ffffff---|
      | Bits 31-24 |                          |
      | DSCP & flag|      some value here     |
      |---------------------------------------|
      			|
      			|
      			v
      |------------skb mark-------------------|
      |            |                          |
      |  zeroed    |                          |
      |---------------------------------------|
      
      Overall parameters:
      
      zone - conntrack zone
      
      control - action related control (reclassify | pipe | drop | continue |
      ok | goto chain <CHAIN_INDEX>)
      Signed-off-by: default avatarKevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
      Reviewed-by: default avatarToke Høiland-Jørgensen <toke@redhat.com>
      Acked-by: default avatarCong Wang <xiyou.wangcong@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      24ec483c
    • Heiner Kallweit's avatar
      r8169: remove 1000/Half from supported modes · a6851c61
      Heiner Kallweit authored
      MAC on the GBit versions supports 1000/Full only, however the PHY
      partially claims to support 1000/Half. So let's explicitly remove
      this mode.
      Signed-off-by: default avatarHeiner Kallweit <hkallweit1@gmail.com>
      Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a6851c61
    • Joergen Andreasen's avatar
      net: mscc: ocelot: Implement port policers via tc command · 2c1d029a
      Joergen Andreasen authored
      Hardware offload of matchall classifier and police action are now
      supported via the tc command.
      Supported police parameters are: rate and burst.
      
      Example:
      
      Add:
      tc qdisc add dev eth3 handle ffff: ingress
      tc filter add dev eth3 parent ffff: prio 1 handle 2	\
      	matchall skip_sw				\
      	action police rate 100Mbit burst 10000
      
      Show:
      tc -s -d qdisc show dev eth3
      tc -s -d filter show dev eth3 ingress
      
      Delete:
      tc filter del dev eth3 parent ffff: prio 1
      tc qdisc del dev eth3 handle ffff: ingress
      Signed-off-by: default avatarJoergen Andreasen <joergen.andreasen@microchip.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2c1d029a
  2. 29 May, 2019 33 commits