Defer the tcf_exts_destroy() in RCU callback to
tc filter workqueue and get RTNL lock.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces a dedicated workqueue for tc filters
so that each tc filter's RCU callback could defer their
action destroy work to this workqueue. The helper
tcf_queue_work() is introduced for them to use.

Because we hold RTNL lock when calling tcf_block_put(), we
can not simply flush works inside it, therefore we have to
defer it again to this workqueue and make sure all flying RCU
callbacks have already queued their work before this one, in
other words, to ensure this is the last one to execute to
prevent any use-after-free.

On the other hand, this makes tcf_block_put() ugly and
harder to understand. Since David and Eric strongly dislike
adding synchronize_rcu(), this is probably the only
solution that could make everyone happy.

Please also see the code comments below.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: a bunch of fixes for some sparse warnings

As Eric noticed, when running 'make C=2 M=net/sctp/', a plenty of
warnings or errors checked by sparse appear. They are all problems
about Endian and type cast.

Most of them are just warnings by which no issues could be caused
while some might be bugs.

This patchset fixes them with four patches basically according to
how they are introduced.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

These warnings were found by running 'make C=2 M=net/sctp/'.
They are there since very beginning.

Note after this patch, there still one warning left in
sctp_outq_flush():
  sctp_chunk_fail(chunk, SCTP_ERROR_INV_STRM)

Since it has been moved to sctp_stream_outq_migrate on net-next,
to avoid the extra job when merging net-next to net, I will post
the fix for it after the merging is done.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These warnings were found by running 'make C=2 M=net/sctp/'.

Commit d4d6fb57 ("sctp: Try not to change a_rwnd when faking a
SACK from SHUTDOWN.") expected to use the peers old rwnd and add
our flight size to the a_rwnd. But with the wrong Endian, it may
not work as well as expected.

So fix it by converting to the right value.

Fixes: d4d6fb57 ("sctp: Try not to change a_rwnd when faking a SACK from SHUTDOWN.")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These warnings were found by running 'make C=2 M=net/sctp/'.

They are introduced by not aware of Endian for the port when
coding transport rhashtable patches.

Fixes: 7fda702f ("sctp: use new rhlist interface on sctp transport rhashtable")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These warnings were found by running 'make C=2 M=net/sctp/'.

They are introduced by not aware of Endian when coding stream
reconf patches.

Since commit c0d8bab6 ("sctp: add get and set sockopt for
reconf_enable") enabled stream reconf feature for users, the
Fixes tag below would use it.

Fixes: c0d8bab6 ("sctp: add get and set sockopt for reconf_enable")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Davide found the following script triggers a NULL pointer
dereference:

ip l a name eth0 type dummy
tc q a dev eth0 parent :1 handle 1: htb

This is because for a freshly created netdevice noop_qdisc
is attached and when passing 'parent :1', kernel actually
tries to match the major handle which is 0 and noop_qdisc
has handle 0 so is matched by mistake. Commit 69012ae4
tries to fix a similar bug but still misses this case.

Handle 0 is not a valid one, should be just skipped. In
fact, kernel uses it as TC_H_UNSPEC.

Fixes: 69012ae4 ("net: sched: fix handling of singleton qdiscs with qdisc_hash")
Fixes: 59cc1f61 ("net: sched:convert qdisc linked list to hashtable")
Reported-by: Davide Caratti <dcaratti@redhat.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now when migrating sock to another one in sctp_sock_migrate(), it only
resets owner sk for the data in receive queues, not the chunks on out
queues.

It would cause that data chunks length on the sock is not consistent
with sk sk_wmem_alloc. When closing the sock or freeing these chunks,
the old sk would never be freed, and the new sock may crash due to
the overflow sk_wmem_alloc.

syzbot found this issue with this series:

  r0 = socket$inet_sctp()
  sendto$inet(r0)
  listen(r0)
  accept4(r0)
  close(r0)

Although listen() should have returned error when one TCP-style socket
is in connecting (I may fix this one in another patch), it could also
be reproduced by peeling off an assoc.

This issue is there since very beginning.

This patch is to reset owner sk for the chunks on out queues so that
sk sk_wmem_alloc has correct value after accept one sock or peeloff
an assoc to one sock.

Note that when resetting owner sk for chunks on outqueue, it has to
sctp_clear_owner_w/skb_orphan chunks before changing assoc->base.sk
first and then sctp_set_owner_w them after changing assoc->base.sk,
due to that sctp_wfree and it's callees are using assoc->base.sk.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

John Fastabend says:

====================
net: sockmap fixes

Last two fixes (as far as I know) for sockmap code this round.

First, we are using the qdisc cb structure when making the data end
calculation. This is really just wrong so, store it with the other
metadata in the correct tcp_skb_cb sturct to avoid breaking things.

Next, with recent work to attach multiple programs to a cgroup a
specific enumeration of return codes was agreed upon. However,
I wrote the sk_skb program types before seeing this work and used
a different convention. Patch 2 in the series aligns the return
codes to avoid breaking with this infrastructure and also aligns
with other programming conventions to avoid being the odd duck out
forcing programs to remember SK_SKB programs are different. Pusing
to net because its a user visible change. With this SK_SKB program
return codes are the same as other cgroup program types.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent additions to support multiple programs in cgroups impose
a strict requirement, "all yes is yes, any no is no". To enforce
this the infrastructure requires the 'no' return code, SK_DROP in
this case, to be 0.

To apply these rules to SK_SKB program types the sk_actions return
codes need to be adjusted.

This fix adds SK_PASS and makes 'SK_DROP = 0'. Finally, remove
SK_ABORTED to remove any chance that the API may allow aborted
program flows to be passed up the stack. This would be incorrect
behavior and allow programs to break existing policies.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

SK_SKB program types use bpf_compute_data to store the end of the
packet data. However, bpf_compute_data assumes the cb is stored in the
qdisc layer format. But, for SK_SKB this is the wrong layer of the
stack for this type.

It happens to work (sort of!) because in most cases nothing happens
to be overwritten today. This is very fragile and error prone.
Fortunately, we have another hole in tcp_skb_cb we can use so lets
put the data_end value there.

Note, SK_SKB program types do not use data_meta, they are failed by
sk_skb_is_valid_access().
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 9a393b5d ("tap: tap as an independent module") created a
separate tap module that implements tap functionality and exports
interfaces that will be used by macvtap and ipvtap modules to create
create respective tap devices.

However, that patch introduced a regression wherein the modules macvtap
and ipvtap can be removed (through modprobe -r) while there are
applications using the respective /dev/tapX devices. These applications
cause kernel to hold reference to /dev/tapX through 'struct cdev
macvtap_cdev' and 'struct cdev ipvtap_dev' defined in macvtap and ipvtap
modules respectively. So,  when the application is later closed the
kernel panics because we are referencing KVA that is present in the
unloaded modules.

----------8<------- Example ----------8<----------
$ sudo ip li add name mv0 link enp7s0 type macvtap
$ sudo ip li show mv0 |grep mv0| awk -e '{print $1 $2}'
  14:mv0@enp7s0:
$ cat /dev/tap14 &
$ lsmod |egrep -i 'tap|vlan'
macvtap                16384  0
macvlan                24576  1 macvtap
tap                    24576  3 macvtap
$ sudo modprobe -r macvtap
$ fg
cat /dev/tap14
^C

<...system panics...>
BUG: unable to handle kernel paging request at ffffffffa038c500
IP: cdev_put+0xf/0x30
----------8<-----------------8<----------

The fix is to set cdev.owner to the module that creates the tap device
(either macvtap or ipvtap). With this set, the operations (in
fs/char_dev.c) on char device holds and releases the module through
cdev_get() and cdev_put() and will not allow the module to unload
prematurely.

Fixes: 9a393b5d (tap: tap as an independent module)
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the unlikely event tcp_mtu_probe() is sending a packet, we
want tp->tcp_mstamp being as accurate as possible.

This means we need to call tcp_mstamp_refresh() a bit earlier in
tcp_write_xmit().

Fixes: 385e2070 ("tcp: use tp->tcp_mstamp in output path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An unaligned alloc_frag->offset caused by previous allocation will
result an unaligned skb->head. This will lead unaligned
skb_shared_info and then unaligned dataref which requires to be
aligned for accessing on some architecture. Fix this by aligning
alloc_frag->offset before the frag refilling.

Fixes: 0bbd7dad ("tun: make tun_build_skb() thread safe")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Wei Wei <dotweiba@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reported-by: Wei Wei <dotweiba@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2017-10-26

This series contains fixes to e1000, igb, ixgbe and i40e.

Vincenzo Maffione fixes a potential race condition which would result in
the interface being up but transmits are disabled in the hardware.

Colin Ian King fixes a possible NULL pointer dereference in e1000, which
was found by Coverity.

Jean-Philippe Brucker fixes a possible kernel panic when a driver cannot
map a transmit buffer, which is caused by an erroneous test.

Alex provides a fix for ixgbe, which is a partial revert of the commit
ffed21bc ("ixgbe: Don't bother clearing buffer memory for descriptor rings")
because the previous commit messed up the exception handling path by
adding the count back in when we did not need to.  Also fixed a typo,
where the transmit ITR setting was being used to determine if we were
using adaptive receive interrupt moderation or not.  Lastly, fixed a
memory leak by including programming descriptors in the cleaned count.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When receiving a Toobig icmpv6 packet, ip6gre_err would just set
tunnel dev's mtu, that's not enough. For skb_dst(skb)'s pmtu may
still be using the old value, it has no chance to be updated with
tunnel dev's mtu.

Jianlin found this issue by reducing route's mtu while running
netperf, the performance went to 0.

ip6ip6 and ip4ip6 tunnel can work well with this, as they lookup
the upper dst and update_pmtu it's pmtu or icmpv6_send a Toobig
to upper socket after setting tunnel dev's mtu.

We couldn't do that for ip6_gre, as gre's inner packet could be
any protocol, it's difficult to handle them (like lookup upper
dst) in a good way.

So this patch is to fix it by updating skb_dst(skb)'s pmtu when
dev->mtu < skb_dst(skb)'s pmtu in tx path. It's safe to do this
update there, as usually dev->mtu <= skb_dst(skb)'s pmtu and no
performance regression can be caused by this.

Fixes: c12b395a ("gre: Support GRE over IPv6")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The similar fix in patch 'ipip: only increase err_count for some
certain type icmp in ipip_err' is needed for ip6gre_err.

In Jianlin's case, udp netperf broke even when receiving a TooBig
icmpv6 packet.

Fixes: c12b395a ("gre: Support GRE over IPv6")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

t->err_count is used to count the link failure on tunnel and an err
will be reported to user socket in tx path if t->err_count is not 0.
udp socket could even return EHOSTUNREACH to users.

Since commit fd58156e ("IPIP: Use ip-tunneling code.") removed
the 'switch check' for icmp type in ipip_err(), err_count would be
increased by the icmp packet with ICMP_EXC_FRAGTIME code. an link
failure would be reported out due to this.

In Jianlin's case, when receiving ICMP_EXC_FRAGTIME a icmp packet,
udp netperf failed with the err:
  send_data: data send error: No route to host (errno 113)

We expect this error reported from tunnel to socket when receiving
some certain type icmp, but not ICMP_EXC_FRAGTIME, ICMP_SR_FAILED
or ICMP_PARAMETERPROB ones.

This patch is to bring 'switch check' for icmp type back to ipip_err
so that it only reports link failure for the right type icmp, just as
in ipgre_err() and ipip6_err().

Fixes: fd58156e ("IPIP: Use ip-tunneling code.")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to DWMAC databook the first queue operating mode
must always be in DCB.

As MTL_QUEUE_DCB = 1, we need to always set the first queue
operating mode to DCB otherwise driver will think that queue
is in AVB mode (because MTL_QUEUE_AVB = 0).
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to DT bindings documentation we are expecting a
property called "snps,read-requests" but we are parsing
instead a property called "read,read-requests".

This is clearly a typo. Fix it.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2017-10-26

The series includes some misc fixes for mlx5 core and etherent driver.
Please pull and let me know if there's any problem.

For -Stable:
net/mlx5e: Properly deal with encap flows add/del under neigh update (kernels >= 4.12)
net/mlx5: Fix health work queue spin lock to IRQ safe  (kernels >= 4.13)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2017-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
pull-request: mac80211 2017-10-25

Here are:
 * follow-up fixes for the WoWLAN security issue, to fix a
   partial TKIP key material problem and to use crypto_memneq()
 * a change for better enforcement of FQ's memory limit
 * a disconnect/connect handling fix, and
 * a user rate mask validation fix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the i40e driver to include programming descriptors in
the cleaned_count. Without this change it becomes possible for us to leak
memory as we don't trigger a large enough allocation when the time comes to
allocate new buffers and we end up overwriting a number of rx_buffers equal
to the number of programming descriptors we encountered.

Fixes: 0e626ff7 ("i40e: Fix support for flow director programming status")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It looks like there was either a copy/paste error or just a typo that
resulted in the Tx ITR setting being used to determine if we were using
adaptive Rx interrupt moderation or not.

This patch fixes the typo.

Fixes: 65e87c03 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a partial revert of "ixgbe: Don't bother clearing buffer
memory for descriptor rings". Specifically I messed up the exception
handling path a bit and this resulted in us incorrectly adding the count
back in when we didn't need to.

In order to make this simpler I am reverting most of the exception handling
path change and instead just replacing the bit that was handled by the
unmap_and_free call.

Fixes: ffed21bc ("ixgbe: Don't bother clearing buffer memory for descriptor rings")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the driver cannot map a TX buffer, instead of rolling back
gracefully and retrying later, we currently get a panic:

[  159.885994] igb 0000:00:00.0: TX DMA map failed
[  159.886588] Unable to handle kernel paging request at virtual address ffff00000a08c7a8
               ...
[  159.897031] PC is at igb_xmit_frame_ring+0x9c8/0xcb8

Fix the erroneous test that leads to this situation.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the stat type is invalid then data[i] is being set
either by dereferencing a null pointer p, or it is reading from
an incorrect previous location if we had a valid stat type
previously.  Fix this by skipping over the read of p on an invalid
stat type.

Detected by CoverityScan, CID#113385 ("Explicit null dereferenced")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a race condition that can result into the interface being
up and carrier on, but with transmits disabled in the hardware.
The bug may show up by repeatedly IFF_DOWN+IFF_UP the interface, which
allows e1000_watchdog() interleave with e1000_down().

    CPU x                           CPU y
    --------------------------------------------------------------------
    e1000_down():
        netif_carrier_off()
                                    e1000_watchdog():
                                        if (carrier == off) {
                                            netif_carrier_on();
                                            enable_hw_transmit();
                                        }
        disable_hw_transmit();
                                    e1000_watchdog():
                                        /* carrier on, do nothing */
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Double free of skb_array in tap module is causing kernel panic. When
tap_set_queue() fails we free skb_array right away by calling
skb_array_cleanup(). However, later on skb_array_cleanup() is called
again by tap_sock_destruct through sock_put(). This patch fixes that
issue.

Fixes: 362899b8 (macvtap: switch to use skb array)
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current implementation calls tcp_rate_skb_sent() when tcp_transmit_skb()
is called when it clones skb only. Not calling tcp_rate_skb_sent() is OK
for all such code paths except from __tcp_retransmit_skb() which happens
when skb->data address is not aligned. This may rarely happen e.g. when
small amount of data is sent initially and the receiver partially acks
odd number of bytes for some reason, possibly malicious.
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In my first attempt to fix the lockdep splat, I forgot we could
enter inet_csk_route_req() with a freshly allocated request socket,
for which refcount has not yet been elevated, due to complex
SLAB_TYPESAFE_BY_RCU rules.

We either are in rcu_read_lock() section _or_ we own a refcount on the
request.

Correct RCU verb to use here is rcu_dereference_check(), although it is
not possible to prove we actually own a reference on a shared
refcount :/

In v2, I added ireq_opt_deref() helper and use in three places, to fix other
possible splats.

[   49.844590]  lockdep_rcu_suspicious+0xea/0xf3
[   49.846487]  inet_csk_route_req+0x53/0x14d
[   49.848334]  tcp_v4_route_req+0xe/0x10
[   49.850174]  tcp_conn_request+0x31c/0x6a0
[   49.851992]  ? __lock_acquire+0x614/0x822
[   49.854015]  tcp_v4_conn_request+0x5a/0x79
[   49.855957]  ? tcp_v4_conn_request+0x5a/0x79
[   49.858052]  tcp_rcv_state_process+0x98/0xdcc
[   49.859990]  ? sk_filter_trim_cap+0x2f6/0x307
[   49.862085]  tcp_v4_do_rcv+0xfc/0x145
[   49.864055]  ? tcp_v4_do_rcv+0xfc/0x145
[   49.866173]  tcp_v4_rcv+0x5ab/0xaf9
[   49.868029]  ip_local_deliver_finish+0x1af/0x2e7
[   49.870064]  ip_local_deliver+0x1b2/0x1c5
[   49.871775]  ? inet_del_offload+0x45/0x45
[   49.873916]  ip_rcv_finish+0x3f7/0x471
[   49.875476]  ip_rcv+0x3f1/0x42f
[   49.876991]  ? ip_local_deliver_finish+0x2e7/0x2e7
[   49.878791]  __netif_receive_skb_core+0x6d3/0x950
[   49.880701]  ? process_backlog+0x7e/0x216
[   49.882589]  __netif_receive_skb+0x1d/0x5e
[   49.884122]  process_backlog+0x10c/0x216
[   49.885812]  net_rx_action+0x147/0x3df

Fixes: a6ca7abe ("tcp/dccp: fix lockdep splat in inet_csk_route_req()")
Fixes: c92e8c02 ("tcp/dccp: fix ireq->opt races")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kernel test robot <fengguang.wu@intel.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The number of unsignaled work-requests posted to the IB send queue is
tracked by a counter in the rds_ib_connection struct. When it reaches
zero, or the caller explicitly asks for it, the send-signaled bit is
set in send_flags and the counter is reset. This is performed by the
rds_ib_set_wr_signal_state() function.

However, this function is not always used which yields inaccurate
accounting. This commit fixes this, re-factors a code bloat related to
the matter, and makes the actual parameter type to the function
consistent.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

send_flags needs to be initialized before calling
rds_ib_set_wr_signal_state().
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.14-20171024' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2017-10-24

here's another pull request for net/master.

The patch by Gerhard Bertelsmann fixes the CAN_CTRLMODE_LOOPBACK in the
sun4i driver. Two patches by Jimmy Assarsson for the kvaser_usb driver
fix a print in the error path of the kvaser_usb_close() and remove a
wrong warning message with the Leaf v2 firmware version v4.1.844.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch replaces GFP_KERNEL by GFP_ATOMIC to avoid sleeping in the
ndo_set_rx_mode() call which is called with BH disabled.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When calling mvpp2_prs_mac_multi_set() from mvpp2_prs_mac_init(), two
parameters (the port index and the table index) are inverted. Fixes
this.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a typo in the mvpp2_prs_tcam_data_cmp() function, as
the shift value is inverted with the data.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, tc with ets type and zero bandwidth is not accepted
by driver. This behavior does not follow the IEEE802.1qaz spec.

If there are tcs with ets type and zero bandwidth, these tcs are
assigned to the lowest priority tc_group #0. We equally distribute
100% bw of the tc_group #0 to these zero bandwidth ets tcs.
Also, the non zero bandwidth ets tcs are assigned to tc_group #1.

If there is no zero bandwidth ets tc, the non zero bandwidth ets tcs
are assigned to tc_group #0.

Fixes: cdcf1121 ("net/mlx5e: Validate BW weight values of ETS")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently, the encap action offload is handled in the actions parse
function and not in mlx5e_tc_add_fdb_flow() where we deal with all
the other aspects of offloading actions (vlan, modify header) and
the rule itself.

When the neigh update code (mlx5e_tc_encap_flows_add()) recreates the
encap entry and offloads the related flows, we wrongly call again into
mlx5e_tc_add_fdb_flow(), this for itself would cause us to handle
again the offloading of vlans and header re-write which puts things
in non consistent state and step on freed memory (e.g the modify
header parse buffer which is already freed).

Since on error, mlx5e_tc_add_fdb_flow() detaches and may release the
encap entry, it causes a corruption at the neigh update code which goes
over the list of flows associated with this encap entry, or double free
when the tc flow is later deleted by user-space.

When neigh update (mlx5e_tc_encap_flows_del()) unoffloads the flows related
to an encap entry which is now invalid, we do a partial repeat of the eswitch
flow removal code which is wrong too.

To fix things up we do the following:

(1) handle the encap action offload in the eswitch flow add function
    mlx5e_tc_add_fdb_flow() as done for the other actions and the rule itself.

(2) modify the neigh update code (mlx5e_tc_encap_flows_add/del) to only
    deal with the encap entry and rules delete/add and not with any of
    the other offloaded actions.

Fixes: 232c0013 ('net/mlx5e: Add support to neighbour update flow')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>